| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When used on Huawei hisi platforms, Prolific Mass Storage Card Reader
which the VID:PID is in 067b:2731 might fail to enumerate at boot time
and doesn't work well with LPM enabled, combination quirks:
USB_QUIRK_DELAY_INIT + USB_QUIRK_NO_LPM
fixed the problems.
Signed-off-by: Miao Li <limiao@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250304070757.139473-1-limiao870622@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A recent cleanup went a bit too far and dropped clearing the cycle bit
of link TRBs, so it stays different from the rest of the ring half of
the time. Then a race occurs: if the xHC reaches such link TRB before
more commands are queued, the link's cycle bit unintentionally matches
the xHC's cycle so it follows the link and waits for further commands.
If more commands are queued before the xHC gets there, inc_enq() flips
the bit so the xHC later sees a mismatch and stops executing commands.
This function is called before suspend and 50% of times after resuming
the xHC is doomed to get stuck sooner or later. Then some Stop Endpoint
command fails to complete in 5 seconds and this shows up
xhci_hcd 0000:00:10.0: xHCI host not responding to stop endpoint command
xhci_hcd 0000:00:10.0: xHCI host controller not responding, assume dead
xhci_hcd 0000:00:10.0: HC died; cleaning up
followed by loss of all USB decives on the affected bus. That's if you
are lucky, because if Set Deq gets stuck instead, the failure is silent.
Likely responsible for kernel bug 219824. I found this while searching
for possible causes of that regression and reproduced it locally before
hearing back from the reporter. To repro, simply wait for link cycle to
become set (debugfs), then suspend, resume and wait. To accelerate the
failure I used a script which repeatedly starts and stops a UVC camera.
Some HCs get fully reinitialized on resume and they are not affected.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219824
Fixes: 36b972d4b7ce ("usb: xhci: improve xhci_clear_command_ring()")
Cc: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250304113147.3322584-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After phy initialization, some phy operations can only be executed while
in lower P states. Ensure GUSB3PIPECTL.SUSPENDENABLE and
GUSB2PHYCFG.SUSPHY are set soon after initialization to avoid blocking
phy ops.
Previously the SUSPENDENABLE bits are only set after the controller
initialization, which may not happen right away if there's no gadget
driver or xhci driver bound. Revise this to clear SUSPENDENABLE bits
only when there's mode switching (change in GCTL.PRTCAPDIR).
Fixes: 6d735722063a ("usb: dwc3: core: Prevent phy suspend during init")
Cc: stable <stable@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/633aef0afee7d56d2316f7cc3e1b2a6d518a8cc9.1738280911.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The xHC resources allocated for USB devices are not released in correct
order after resuming in case when while suspend device was reconnected.
This issue has been detected during the fallowing scenario:
- connect hub HS to root port
- connect LS/FS device to hub port
- wait for enumeration to finish
- force host to suspend
- reconnect hub attached to root port
- wake host
For this scenario during enumeration of USB LS/FS device the Cadence xHC
reports completion error code for xHC commands because the xHC resources
used for devices has not been properly released.
XHCI specification doesn't mention that device can be reset in any order
so, we should not treat this issue as Cadence xHC controller bug.
Similar as during disconnecting in this case the device resources should
be cleared starting form the last usb device in tree toward the root hub.
To fix this issue usbcore driver should call hcd->driver->reset_device
for all USB devices connected to hub which was reconnected while
suspending.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/PH7PR07MB953841E38C088678ACDCF6EEDDCC2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When performing continuous unbind/bind operations on the USB drivers
available on the Renesas RZ/G2L SoC, a kernel crash with the message
"Unable to handle kernel NULL pointer dereference at virtual address"
may occur. This issue points to the usbhsc_notify_hotplug() function.
Flush the delayed work to avoid its execution when driver resources are
unavailable.
Fixes: bc57381e6347 ("usb: renesas_usbhs: use delayed_work instead of work_struct")
Cc: stable <stable@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250225110248.870417-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The gpriv->transceiver is retrieved in probe() through usb_get_phy() but
never released. Use devm_usb_get_phy() to handle this scenario.
This issue was identified through code investigation. No issue was found
without this change.
Fixes: b5a2875605ca ("usb: renesas_usbhs: Allow an OTG PHY driver to provide VBUS")
Cc: stable <stable@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250225110248.870417-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Clocks acquired with of_clk_get() need to be freed with clk_put(). Call
clk_put() on priv->clks[0] on error path.
Fixes: 3df0e240caba ("usb: renesas_usbhs: Add multiple clocks management")
Cc: stable <stable@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250225110248.870417-2-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While commit d325a1de49d6 ("usb: dwc3: gadget: Prevent losing events in
event cache") makes sure that top half(TH) does not end up overwriting the
cached events before processing them when the TH gets invoked more than one
time, returning IRQ_HANDLED results in occasional irq storm where the TH
hogs the CPU. The irq storm can be prevented by the flag before event
handler busy is cleared. Default enable interrupt moderation in all
versions which support them.
ftrace event stub during dwc3 irq storm:
irq/504_dwc3-1111 ( 1111) [000] .... 70.000866: irq_handler_exit: irq=14 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000872: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000874: irq_handler_exit: irq=504 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000881: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000883: irq_handler_exit: irq=504 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000889: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000892: irq_handler_exit: irq=504 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000898: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000901: irq_handler_exit: irq=504 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000907: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000909: irq_handler_exit: irq=504 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000915: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000918: irq_handler_exit: irq=504 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000924: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000927: irq_handler_exit: irq=504 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000933: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000935: irq_handler_exit: irq=504 ret=handled
....
Cc: stable <stable@kernel.org>
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Fixes: d325a1de49d6 ("usb: dwc3: gadget: Prevent losing events in event cache")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250216223003.3568039-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the USB configuration is not valid, then avoid checking for
bmAttributes to prevent null pointer deference.
Cc: stable <stable@kernel.org>
Fixes: 40e89ff5750f ("usb: gadget: Set self-powered based on MaxPower and bmAttributes")
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250224085604.417327-1-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When adding support for USB3-over-USB4 tunnelling detection, a check
for an Intel-specific capability was added. This capability, which
goes by ID 206, is used without any check that we are actually
dealing with an Intel host.
As it turns out, the Cadence XHCI controller *also* exposes an
extended capability numbered 206 (for unknown purposes), but of
course doesn't have the Intel-specific registers that the tunnelling
code is trying to access. Fun follows.
The core of the problems is that the tunnelling code blindly uses
vendor-specific capabilities without any check (the Intel-provided
documentation I have at hand indicates that 192-255 are indeed
vendor-specific).
Restrict the detection code to Intel HW for real, preventing any
further explosion on my (non-Intel) HW.
Cc: stable <stable@kernel.org>
Fixes: 948ce83fbb7df ("xhci: Add USB4 tunnel detection for USB3 devices on Intel hosts")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250227194529.2288718-1-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Raspberry Pi is a major user of those chips and they discovered a bug -
when the end of a transfer ring segment is reached, up to four TRBs can
be prefetched from the next page even if the segment ends with link TRB
and on page boundary (the chip claims to support standard 4KB pages).
It also appears that if the prefetched TRBs belong to a different ring
whose doorbell is later rung, they may be used without refreshing from
system RAM and the endpoint will stay idle if their cycle bit is stale.
Other users complain about IOMMU faults on x86 systems, unsurprisingly.
Deal with it by using existing quirk which allocates a dummy page after
each transfer ring segment. This was seen to resolve both problems. RPi
came up with a more efficient solution, shortening each segment by four
TRBs, but it complicated the driver and they ditched it for this quirk.
Also rename the quirk and add VL805 device ID macro.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Link: https://github.com/raspberrypi/linux/issues/4685
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=215906
CC: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250225095927.2512358-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
cdev->config might be NULL, so check it before dereferencing.
CC: stable <stable@kernel.org>
Fixes: 40e89ff5750f ("usb: gadget: Set self-powered based on MaxPower and bmAttributes")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20250220120314.3614330-1-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is observed that on some systems an initial PPM reset during the boot
phase can trigger a timeout:
[ 6.482546] ucsi_acpi USBC000:00: failed to reset PPM!
[ 6.482551] ucsi_acpi USBC000:00: error -ETIMEDOUT: PPM init failed
Still, increasing the timeout value, albeit being the most straightforward
solution, eliminates the problem: the initial PPM reset may take up to
~8000-10000ms on some Lenovo laptops. When it is reset after the above
period of time (or even if ucsi_reset_ppm() is not called overall), UCSI
works as expected.
Moreover, if the ucsi_acpi module is loaded/unloaded manually after the
system has booted, reading the CCI values and resetting the PPM works
perfectly, without any timeout. Thus it's only a boot-time issue.
The reason for this behavior is not clear but it may be the consequence
of some tricks that the firmware performs or be an actual firmware bug.
As a workaround, increase the timeout to avoid failing the UCSI
initialization prematurely.
Fixes: b1b59e16075f ("usb: typec: ucsi: Increase command completion timeout value")
Cc: stable <stable@kernel.org>
Signed-off-by: Fedor Pchelkin <boddah8794@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250217105442.113486-3-boddah8794@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For the ACPI backend of UCSI the UCSI "registers" are just a memory copy
of the register values in an opregion. The ACPI implementation in the
BIOS ensures that the opregion contents are synced to the embedded
controller and it ensures that the registers (in particular CCI) are
synced back to the opregion on notifications. While there is an ACPI call
that syncs the actual registers to the opregion there is rarely a need to
do this and on some ACPI implementations it actually breaks in various
interesting ways.
The only reason to force a sync from the embedded controller is to poll
CCI while notifications are disabled. Only the ucsi core knows if this
is the case and guessing based on the current command is suboptimal, i.e.
leading to the following spurious assertion splat:
WARNING: CPU: 3 PID: 76 at drivers/usb/typec/ucsi/ucsi.c:1388 ucsi_reset_ppm+0x1b4/0x1c0 [typec_ucsi]
CPU: 3 UID: 0 PID: 76 Comm: kworker/3:0 Not tainted 6.12.11-200.fc41.x86_64 #1
Hardware name: LENOVO 21D0/LNVNB161216, BIOS J6CN45WW 03/17/2023
Workqueue: events_long ucsi_init_work [typec_ucsi]
RIP: 0010:ucsi_reset_ppm+0x1b4/0x1c0 [typec_ucsi]
Call Trace:
<TASK>
ucsi_init_work+0x3c/0xac0 [typec_ucsi]
process_one_work+0x179/0x330
worker_thread+0x252/0x390
kthread+0xd2/0x100
ret_from_fork+0x34/0x50
ret_from_fork_asm+0x1a/0x30
</TASK>
Thus introduce a ->poll_cci() method that works like ->read_cci() with an
additional forced sync and document that this should be used when polling
with notifications disabled. For all other backends that presumably don't
have this issue use the same implementation for both methods.
Fixes: fa48d7e81624 ("usb: typec: ucsi: Do not call ACPI _DSM method for UCSI read operations")
Cc: stable <stable@kernel.org>
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Tested-by: Fedor Pchelkin <boddah8794@gmail.com>
Signed-off-by: Fedor Pchelkin <boddah8794@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250217105442.113486-2-boddah8794@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During probe, the TCPC alert interrupts are getting masked to
avoid unwanted interrupts during chip setup: this is ok to do
but there is no unmasking happening at any later time, which
means that the chip will not raise any interrupt, essentially
making it not functional as, while internally it does perform
all of the intended functions, it won't signal anything to the
outside.
Unmask the alert interrupts to fix functionality.
Fixes: ce08eaeb6388 ("staging: typec: rt1711h typec chip driver")
Cc: stable <stable@kernel.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20250219114700.41700-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently the USB gadget will be set as bus-powered based solely
on whether its bMaxPower is greater than 100mA, but this may miss
devices that may legitimately draw less than 100mA but still want
to report as bus-powered. Similarly during suspend & resume, USB
gadget is incorrectly marked as bus/self powered without checking
the bmAttributes field. Fix these by configuring the USB gadget
as self or bus powered based on bmAttributes, and explicitly set
it as bus-powered if it draws more than 100mA.
Cc: stable <stable@kernel.org>
Fixes: 5e5caf4fa8d3 ("usb: gadget: composite: Inform controller driver of self-powered")
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250217120328.2446639-1-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently while UDC suspends, u_ether attempts to remote wakeup
the host if there are any pending transfers. However, if remote
wakeup fails, the UDC remains suspended but the is_suspend flag
is not set. And since is_suspend flag isn't set, the subsequent
eth_start_xmit() would queue USB requests to suspended UDC.
To fix this, bail out from gether_suspend() only if remote wakeup
operation is successful.
Cc: stable <stable@kernel.org>
Fixes: 0a1af6dfa077 ("usb: gadget: f_ecm: Add suspend/resume and remote wakeup support")
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250212100840.3812153-1-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Syzbot once again identified a flaw in usb endpoint checking, see [1].
This time the issue stems from a commit authored by me (2eabb655a968
("usb: atm: cxacru: fix endpoint checking in cxacru_bind()")).
While using usb_find_common_endpoints() may usually be enough to
discard devices with wrong endpoints, in this case one needs more
than just finding and identifying the sufficient number of endpoints
of correct types - one needs to check the endpoint's address as well.
Since cxacru_bind() fills URBs with CXACRU_EP_CMD address in mind,
switch the endpoint verification approach to usb_check_XXX_endpoints()
instead to fix incomplete ep testing.
[1] Syzbot report:
usb 5-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 0 PID: 1378 at drivers/usb/core/urb.c:504 usb_submit_urb+0xc4e/0x18c0 drivers/usb/core/urb.c:503
...
RIP: 0010:usb_submit_urb+0xc4e/0x18c0 drivers/usb/core/urb.c:503
...
Call Trace:
<TASK>
cxacru_cm+0x3c8/0xe50 drivers/usb/atm/cxacru.c:649
cxacru_card_status drivers/usb/atm/cxacru.c:760 [inline]
cxacru_bind+0xcf9/0x1150 drivers/usb/atm/cxacru.c:1223
usbatm_usb_probe+0x314/0x1d30 drivers/usb/atm/usbatm.c:1058
cxacru_usb_probe+0x184/0x220 drivers/usb/atm/cxacru.c:1377
usb_probe_interface+0x641/0xbb0 drivers/usb/core/driver.c:396
really_probe+0x2b9/0xad0 drivers/base/dd.c:658
__driver_probe_device+0x1a2/0x390 drivers/base/dd.c:800
driver_probe_device+0x50/0x430 drivers/base/dd.c:830
...
Reported-and-tested-by: syzbot+ccbbc229a024fa3e13b5@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=ccbbc229a024fa3e13b5
Fixes: 2eabb655a968 ("usb: atm: cxacru: fix endpoint checking in cxacru_bind()")
Cc: stable@kernel.org
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20250213122259.730772-1-n.zhandarovich@fintech.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
The pages_touched field represents the number of subbuffers in the ring
buffer that have content that can be read. This is used in accounting of
"dirty_pages" and "buffer_percent" to allow the user to wait for the
buffer to be filled to a certain amount before it reads the buffer in
blocking mode.
The persistent buffer never updated this value so it was set to zero, and
this accounting would take it as it had no content. This would cause user
space to wait for content even though there's enough content in the ring
buffer that satisfies the buffer_percent.
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Vincent Donnefort <vdonnefort@google.com>
Link: https://lore.kernel.org/20250214123512.0631436e@gandalf.local.home
Fixes: 5f3b6e839f3ce ("ring-buffer: Validate boot range memory events")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
When trying to mmap a trace instance buffer that is attached to
reserve_mem, it would crash:
BUG: unable to handle page fault for address: ffffe97bd00025c8
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 2862f3067 P4D 2862f3067 PUD 0
Oops: Oops: 0000 [#1] PREEMPT_RT SMP PTI
CPU: 4 UID: 0 PID: 981 Comm: mmap-rb Not tainted 6.14.0-rc2-test-00003-g7f1a5e3fbf9e-dirty #233
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
RIP: 0010:validate_page_before_insert+0x5/0xb0
Code: e2 01 89 d0 c3 cc cc cc cc 66 66 2e 0f 1f 84 00 00 00 00 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 <48> 8b 46 08 a8 01 75 67 66 90 48 89 f0 8b 50 34 85 d2 74 76 48 89
RSP: 0018:ffffb148c2f3f968 EFLAGS: 00010246
RAX: ffff9fa5d3322000 RBX: ffff9fa5ccff9c08 RCX: 00000000b879ed29
RDX: ffffe97bd00025c0 RSI: ffffe97bd00025c0 RDI: ffff9fa5ccff9c08
RBP: ffffb148c2f3f9f0 R08: 0000000000000004 R09: 0000000000000004
R10: 0000000000000000 R11: 0000000000000200 R12: 0000000000000000
R13: 00007f16a18d5000 R14: ffff9fa5c48db6a8 R15: 0000000000000000
FS: 00007f16a1b54740(0000) GS:ffff9fa73df00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffe97bd00025c8 CR3: 00000001048c6006 CR4: 0000000000172ef0
Call Trace:
<TASK>
? __die_body.cold+0x19/0x1f
? __die+0x2e/0x40
? page_fault_oops+0x157/0x2b0
? search_module_extables+0x53/0x80
? validate_page_before_insert+0x5/0xb0
? kernelmode_fixup_or_oops.isra.0+0x5f/0x70
? __bad_area_nosemaphore+0x16e/0x1b0
? bad_area_nosemaphore+0x16/0x20
? do_kern_addr_fault+0x77/0x90
? exc_page_fault+0x22b/0x230
? asm_exc_page_fault+0x2b/0x30
? validate_page_before_insert+0x5/0xb0
? vm_insert_pages+0x151/0x400
__rb_map_vma+0x21f/0x3f0
ring_buffer_map+0x21b/0x2f0
tracing_buffers_mmap+0x70/0xd0
__mmap_region+0x6f0/0xbd0
mmap_region+0x7f/0x130
do_mmap+0x475/0x610
vm_mmap_pgoff+0xf2/0x1d0
ksys_mmap_pgoff+0x166/0x200
__x64_sys_mmap+0x37/0x50
x64_sys_call+0x1670/0x1d70
do_syscall_64+0xbb/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
The reason was that the code that maps the ring buffer pages to user space
has:
page = virt_to_page((void *)cpu_buffer->subbuf_ids[s]);
And uses that in:
vm_insert_pages(vma, vma->vm_start, pages, &nr_pages);
But virt_to_page() does not work with vmap()'d memory which is what the
persistent ring buffer has. It is rather trivial to allow this, but for
now just disable mmap() of instances that have their ring buffer from the
reserve_mem option.
If an mmap() is performed on a persistent buffer it will return -ENODEV
just like it would if the .mmap field wasn't defined in the
file_operations structure.
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Vincent Donnefort <vdonnefort@google.com>
Link: https://lore.kernel.org/20250214115547.0d7287d3@gandalf.local.home
Fixes: 9b7bdf6f6ece6 ("tracing: Have trace_printk not use binary prints if boot buffer")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Namely: s/becasue/because/ and s/wiht/with/ plus an added article.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
scripts/Makefile.clang was changed in the linked commit to move --target from
KBUILD_CFLAGS to KBUILD_CPPFLAGS, as that generally has a broader scope.
However that variable is not inspected by the userprogs logic,
breaking cross compilation on clang.
Use both variables to detect bitsize and target arguments for userprogs.
Fixes: feb843a469fb ("kbuild: add $(CLANG_FLAGS) to KBUILD_CPPFLAGS")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
The Tegra210 Audio DMA controller driver did a plain divide:
page_no = (res_page->start - res_base->start) / cdata->ch_base_offset;
which causes problems on 32-bit x86 configurations that have 64-bit
resource sizes:
x86_64-linux-ld: drivers/dma/tegra210-adma.o: in function `tegra_adma_probe':
tegra210-adma.c:(.text+0x1322): undefined reference to `__udivdi3'
because gcc doesn't generate the trivial code for a 64-by-32 divide,
turning it into a function call to do a full 64-by-64 divide. And the
kernel intentionally doesn't provide that helper function, because 99%
of the time all you want is the narrower version.
Of course, tegra210 is a 64-bit architecture and the 32-bit x86 build is
purely for build testing, so this really is just about build coverage
failure.
But build coverage is good.
Side note: div_u64() would be suboptimal if you actually have a 32-bit
resource_t, so our "helper" for divides are admittedly making it harder
than it should be to generate good code for all the possible cases.
At some point, I'll consider 32-bit x86 so entirely legacy that I can't
find it in myself to care any more, and we'll just add the __udivdi3
library function.
But for now, the right thing to do is to use "div_u64()" to show that
you know that you are doing the simpler divide with a 32-bit number.
And the build error enforces that.
While fixing the build issue, also check for division-by-zero, and for
overflow. Which hopefully cannot happen on real production hardware,
but the value of 'ch_base_offset' can definitely be zero in other
places.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since commit 5f73e7d0386d ("kbuild: refactor cross-compiling
linux-headers package"), the linux-headers Debian package fails to
build when $(CC) cannot build userspace applications, for example,
when using toolchains installed by the 0day bot.
The host programs in the linux-headers package should be rebuilt using
the disto's cross-compiler, ${DEB_HOST_GNU_TYPE}-gcc instead of $(CC).
Hence, the variable 'CC' must be expanded in this shell script instead
of in the top-level Makefile.
Commit f354fc88a72a ("kbuild: install-extmod-build: add missing
quotation marks for CC variable") was not a correct fix because
CC="ccache gcc" should be unrelated when rebuilding userspace tools.
Fixes: 5f73e7d0386d ("kbuild: refactor cross-compiling linux-headers package")
Reported-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Closes: https://lore.kernel.org/linux-kbuild/CAK7LNARb3xO3ptBWOMpwKcyf3=zkfhMey5H2KnB1dOmUwM79dA@mail.gmail.com/T/#t
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
When CONFIG_OBJTOOL=y or CONFIG_DEBUG_INFO_BTF=y, parallel builds
show awkward "mkdir -p ..." logs.
$ make -j16
[ snip ]
mkdir -p /home/masahiro/ref/linux/tools/objtool && make O=/home/masahiro/ref/linux subdir=tools/objtool --no-print-directory -C objtool
mkdir -p /home/masahiro/ref/linux/tools/bpf/resolve_btfids && make O=/home/masahiro/ref/linux subdir=tools/bpf/resolve_btfids --no-print-directory -C bpf/resolve_btfids
Defining MAKEFLAGS=<value> on the command line wipes out command line
switches from the resultant MAKEFLAGS definition, even though the command
line switches are active. [1]
MAKEFLAGS puts all single-letter options into the first word, and that
word will be empty if no single-letter options were given. [2]
However, this breaks if MAKEFLAGS=<value> is given on the command line.
The tools/ and tools/% targets set MAKEFLAGS=<value> on the command
line, which breaks the following code in tools/scripts/Makefile.include:
short-opts := $(firstword -$(MAKEFLAGS))
If MAKEFLAGS really needs modification, it should be done through the
environment variable, as follows:
MAKEFLAGS=<value> $(MAKE) ...
That said, I question whether modifying MAKEFLAGS is necessary here.
The only flag we might want to exclude is --no-print-directory, as the
tools build system changes the working directory. However, people might
find the "Entering/Leaving directory" logs annoying.
I simply removed the offending MAKEFLAGS=<value>.
[1]: https://savannah.gnu.org/bugs/?62469
[2]: https://www.gnu.org/software/make/manual/make.html#Testing-Flags
Fixes: ea01fa9f63ae ("tools: Connect to the kernel build system")
Fixes: a50e43332756 ("perf tools: Honor parallel jobs")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Daniel Xu <dxu@dxuuu.xyz>
|
|
Fix issues with enabling SNP host support and effectively SNP support
which is broken with respect to the KVM module being built-in.
SNP host support is enabled in snp_rmptable_init() which is invoked as
device_initcall(). SNP check on IOMMU is done during IOMMU PCI init
(IOMMU_PCI_INIT stage). And for that reason snp_rmptable_init() is
currently invoked via device_initcall() and cannot be invoked via
subsys_initcall() as core IOMMU subsystem gets initialized via
subsys_initcall().
Now, if kvm_amd module is built-in, it gets initialized before SNP host
support is enabled in snp_rmptable_init() :
[ 10.131811] kvm_amd: TSC scaling supported
[ 10.136384] kvm_amd: Nested Virtualization enabled
[ 10.141734] kvm_amd: Nested Paging enabled
[ 10.146304] kvm_amd: LBR virtualization supported
[ 10.151557] kvm_amd: SEV enabled (ASIDs 100 - 509)
[ 10.156905] kvm_amd: SEV-ES enabled (ASIDs 1 - 99)
[ 10.162256] kvm_amd: SEV-SNP enabled (ASIDs 1 - 99)
[ 10.171508] kvm_amd: Virtual VMLOAD VMSAVE supported
[ 10.177052] kvm_amd: Virtual GIF supported
...
...
[ 10.201648] kvm_amd: in svm_enable_virtualization_cpu
And then svm_x86_ops->enable_virtualization_cpu()
(svm_enable_virtualization_cpu) programs MSR_VM_HSAVE_PA as following:
wrmsrl(MSR_VM_HSAVE_PA, sd->save_area_pa);
So VM_HSAVE_PA is non-zero before SNP support is enabled on all CPUs.
snp_rmptable_init() gets invoked after svm_enable_virtualization_cpu()
as following :
...
[ 11.256138] kvm_amd: in svm_enable_virtualization_cpu
...
[ 11.264918] SEV-SNP: in snp_rmptable_init
This triggers a #GP exception in snp_rmptable_init() when snp_enable()
is invoked to set SNP_EN in SYSCFG MSR:
[ 11.294289] unchecked MSR access error: WRMSR to 0xc0010010 (tried to write 0x0000000003fc0000) at rIP: 0xffffffffaf5d5c28 (native_write_msr+0x8/0x30)
...
[ 11.294404] Call Trace:
[ 11.294482] <IRQ>
[ 11.294513] ? show_stack_regs+0x26/0x30
[ 11.294522] ? ex_handler_msr+0x10f/0x180
[ 11.294529] ? search_extable+0x2b/0x40
[ 11.294538] ? fixup_exception+0x2dd/0x340
[ 11.294542] ? exc_general_protection+0x14f/0x440
[ 11.294550] ? asm_exc_general_protection+0x2b/0x30
[ 11.294557] ? __pfx_snp_enable+0x10/0x10
[ 11.294567] ? native_write_msr+0x8/0x30
[ 11.294570] ? __snp_enable+0x5d/0x70
[ 11.294575] snp_enable+0x19/0x20
[ 11.294578] __flush_smp_call_function_queue+0x9c/0x3a0
[ 11.294586] generic_smp_call_function_single_interrupt+0x17/0x20
[ 11.294589] __sysvec_call_function+0x20/0x90
[ 11.294596] sysvec_call_function+0x80/0xb0
[ 11.294601] </IRQ>
[ 11.294603] <TASK>
[ 11.294605] asm_sysvec_call_function+0x1f/0x30
...
[ 11.294631] arch_cpu_idle+0xd/0x20
[ 11.294633] default_idle_call+0x34/0xd0
[ 11.294636] do_idle+0x1f1/0x230
[ 11.294643] ? complete+0x71/0x80
[ 11.294649] cpu_startup_entry+0x30/0x40
[ 11.294652] start_secondary+0x12d/0x160
[ 11.294655] common_startup_64+0x13e/0x141
[ 11.294662] </TASK>
This #GP exception is getting triggered due to the following errata for
AMD family 19h Models 10h-1Fh Processors:
Processor may generate spurious #GP(0) Exception on WRMSR instruction:
Description:
The Processor will generate a spurious #GP(0) Exception on a WRMSR
instruction if the following conditions are all met:
- the target of the WRMSR is a SYSCFG register.
- the write changes the value of SYSCFG.SNPEn from 0 to 1.
- One of the threads that share the physical core has a non-zero
value in the VM_HSAVE_PA MSR.
The document being referred to above:
https://www.amd.com/content/dam/amd/en/documents/processor-tech-docs/revision-guides/57095-PUB_1_01.pdf
To summarize, with kvm_amd module being built-in, KVM/SVM initialization
happens before host SNP is enabled and this SVM initialization
sets VM_HSAVE_PA to non-zero, which then triggers a #GP when
SYSCFG.SNPEn is being set and this will subsequently cause
SNP_INIT(_EX) to fail with INVALID_CONFIG error as SYSCFG[SnpEn] is not
set on all CPUs.
Essentially SNP host enabling code should be invoked before KVM
initialization, which is currently not the case when KVM is built-in.
Add fix to call snp_rmptable_init() early from iommu_snp_enable()
directly and not invoked via device_initcall() which enables SNP host
support before KVM initialization with kvm_amd module built-in.
Add additional handling for `iommu=off` or `amd_iommu=off` options.
Note that IOMMUs need to be enabled for SNP initialization, therefore,
if host SNP support is enabled but late IOMMU initialization fails
then that will cause PSP driver's SNP_INIT to fail as IOMMU SNP sanity
checks in SNP firmware will fail with invalid configuration error as
below:
[ 9.723114] ccp 0000:23:00.1: sev enabled
[ 9.727602] ccp 0000:23:00.1: psp enabled
[ 9.732527] ccp 0000:a2:00.1: enabling device (0000 -> 0002)
[ 9.739098] ccp 0000:a2:00.1: no command queues available
[ 9.745167] ccp 0000:a2:00.1: psp enabled
[ 9.805337] ccp 0000:23:00.1: SEV-SNP: failed to INIT rc -5, error 0x3
[ 9.866426] ccp 0000:23:00.1: SEV API:1.53 build:5
Fixes: c3b86e61b756 ("x86/cpufeatures: Enable/unmask SEV-SNP CPU feature")
Co-developed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Co-developed-by: Vasant Hegde <vasant.hegde@amd.com>
Signed-off-by: Vasant Hegde <vasant.hegde@amd.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Ashish Kalra <ashish.kalra@amd.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Message-ID: <138b520fb83964782303b43ade4369cd181fdd9c.1739226950.git.ashish.kalra@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The kernel's initcall infrastructure lacks the ability to express
dependencies between initcalls, whereas the modules infrastructure
automatically handles dependencies via symbol loading. Ensure the
PSP SEV driver is initialized before proceeding in sev_hardware_setup()
if KVM is built-in as the dependency isn't handled by the initcall
infrastructure.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Ashish Kalra <ashish.kalra@amd.com>
Message-ID: <f78ddb64087df27e7bcb1ae0ab53f55aa0804fab.1739226950.git.ashish.kalra@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
KVM is dependent on the PSP SEV driver and PSP SEV driver needs to be
loaded before KVM module. In case of module loading any dependent
modules are automatically loaded but in case of built-in modules there
is no inherent mechanism available to specify dependencies between
modules and ensure that any dependent modules are loaded implicitly.
Add a new external API interface for PSP module initialization which
allows PSP SEV driver to be loaded explicitly if KVM is built-in.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Co-developed-by: Ashish Kalra <ashish.kalra@amd.com>
Signed-off-by: Ashish Kalra <ashish.kalra@amd.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-ID: <15279ca0cad56a07cf12834ec544310f85ff5edc.1739226950.git.ashish.kalra@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Remove hard-coded strings by using the str_yes_no() helper function.
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Matt Turner <mattst88@gmail.com>
|
|
Replace the deprecated one-element array with a modern flexible array
member in the struct crb_struct.
Reviewed-by: Kees Cook <kees@kernel.org>
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Matt Turner <mattst88@gmail.com>
|
|
do_page_fault() and do_entUna() are special because they use
non-standard stack frame layout. Fix them manually.
Cc: stable@vger.kernel.org
Tested-by: Maciej W. Rozycki <macro@orcam.me.uk>
Tested-by: Magnus Lindholm <linmag7@gmail.com>
Tested-by: Matt Turner <mattst88@gmail.com>
Reviewed-by: Maciej W. Rozycki <macro@orcam.me.uk>
Suggested-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Ivan Kokshaysky <ink@unseen.parts>
Signed-off-by: Matt Turner <mattst88@gmail.com>
|
|
The problem is that GCC expects 16-byte alignment of the incoming stack
since early 2004, as Maciej found out [1]:
Having actually dug speculatively I can see that the psABI was changed in
GCC 3.5 with commit e5e10fb4a350 ("re PR target/14539 (128-bit long double
improperly aligned)") back in Mar 2004, when the stack pointer alignment
was increased from 8 bytes to 16 bytes, and arch/alpha/kernel/entry.S has
various suspicious stack pointer adjustments, starting with SP_OFF which
is not a whole multiple of 16.
Also, as Magnus noted, "ALPHA Calling Standard" [2] required the same:
D.3.1 Stack Alignment
This standard requires that stacks be octaword aligned at the time a
new procedure is invoked.
However:
- the "normal" kernel stack is always misaligned by 8 bytes, thanks to
the odd number of 64-bit words in 'struct pt_regs', which is the very
first thing pushed onto the kernel thread stack;
- syscall, fault, interrupt etc. handlers may, or may not, receive aligned
stack depending on numerous factors.
Somehow we got away with it until recently, when we ended up with
a stack corruption in kernel/smp.c:smp_call_function_single() due to
its use of 32-byte aligned local data and the compiler doing clever
things allocating it on the stack.
This adds padding between the PAL-saved and kernel-saved registers
so that 'struct pt_regs' have an even number of 64-bit words.
This makes the stack properly aligned for most of the kernel
code, except two handlers which need special threatment.
Note: struct pt_regs doesn't belong in uapi/asm; this should be fixed,
but let's put this off until later.
Link: https://lore.kernel.org/rcu/alpine.DEB.2.21.2501130248010.18889@angie.orcam.me.uk/ [1]
Link: https://bitsavers.org/pdf/dec/alpha/Alpha_Calling_Standard_Rev_2.0_19900427.pdf [2]
Cc: stable@vger.kernel.org
Tested-by: Maciej W. Rozycki <macro@orcam.me.uk>
Tested-by: Magnus Lindholm <linmag7@gmail.com>
Tested-by: Matt Turner <mattst88@gmail.com>
Reviewed-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Ivan Kokshaysky <ink@unseen.parts>
Signed-off-by: Matt Turner <mattst88@gmail.com>
|
|
This allows the assembly in entry.S to automatically keep in sync with
changes in the stack layout (struct pt_regs and struct switch_stack).
Cc: stable@vger.kernel.org
Tested-by: Maciej W. Rozycki <macro@orcam.me.uk>
Tested-by: Matt Turner <mattst88@gmail.com>
Reviewed-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Ivan Kokshaysky <ink@unseen.parts>
Signed-off-by: Matt Turner <mattst88@gmail.com>
|
|
The meta data for a mapped ring buffer contains an array of indexes of all
the subbuffers. The first entry is the reader page, and the rest of the
entries lay out the order of the subbuffers in how the ring buffer link
list is to be created.
The validator currently makes sure that all the entries are within the
range of 0 and nr_subbufs. But it does not check if there are any
duplicates.
While working on the ring buffer, I corrupted this array, where I added
duplicates. The validator did not catch it and created the ring buffer
link list on top of it. Luckily, the corruption was only that the reader
page was also in the writer path and only presented corrupted data but did
not crash the kernel. But if there were duplicates in the writer side,
then it could corrupt the ring buffer link list and cause a crash.
Create a bitmask array with the size of the number of subbuffers. Then
clear it. When walking through the subbuf array checking to see if the
entries are within the range, test if its bit is already set in the
subbuf_mask. If it is, then there is duplicates and fail the validation.
If not, set the corresponding bit and continue.
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Vincent Donnefort <vdonnefort@google.com>
Link: https://lore.kernel.org/20250214102820.7509ddea@gandalf.local.home
Fixes: c76883f18e59b ("ring-buffer: Add test if range of boot buffer is valid")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Currently if __tracing_resize_ring_buffer() returns an error, the
tracing_resize_ringbuffer() returns -ENOMEM. But it may not be a memory
issue that caused the function to fail. If the ring buffer is memory
mapped, then the resizing of the ring buffer will be disabled. But if the
user tries to resize the buffer, it will get an -ENOMEM returned, which is
confusing because there is plenty of memory. The actual error returned was
-EBUSY, which would make much more sense to the user.
Cc: stable@vger.kernel.org
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Vincent Donnefort <vdonnefort@google.com>
Link: https://lore.kernel.org/20250213134132.7e4505d7@gandalf.local.home
Fixes: 117c39200d9d7 ("ring-buffer: Introducing ring-buffer mapping functions")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
|
|
Memory mapping the tracing ring buffer will disable resizing the buffer.
But if there's an error in the memory mapping like an invalid parameter,
the function exits out without re-enabling the resizing of the ring
buffer, preventing the ring buffer from being resized after that.
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Vincent Donnefort <vdonnefort@google.com>
Link: https://lore.kernel.org/20250213131957.530ec3c5@gandalf.local.home
Fixes: 117c39200d9d7 ("ring-buffer: Introducing ring-buffer mapping functions")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Fix several issues in partition probing:
- The bailout for a bad partoffset must use put_dev_sector(), since the
preceding read_part_sector() succeeded.
- If the partition table claims a silly sector size like 0xfff bytes
(which results in partition table entries straddling sector boundaries),
bail out instead of accessing out-of-bounds memory.
- We must not assume that the partition table contains proper NUL
termination - use strnlen() and strncmp() instead of strlen() and
strcmp().
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20250214-partition-mac-v1-1-c1c626dffbd5@google.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When flushing the serial port's buffer, uart_flush_buffer() calls
kfifo_reset() but if there is an outstanding DMA transfer then the
completion function will consume data from the kfifo via
uart_xmit_advance(), underflowing and leading to ongoing DMA as the
driver tries to transmit another 2^32 bytes.
This is readily reproduced with serial-generic and amidi sending even
short messages as closing the device on exit will wait for the fifo to
drain and in the underflow case amidi hangs for 30 seconds on exit in
tty_wait_until_sent(). A trace of that gives:
kworker/1:1-84 [001] 51.769423: bprint: serial8250_tx_dma: tx_size=3 fifo_len=3
amidi-763 [001] 51.769460: bprint: uart_flush_buffer: resetting fifo
irq/21-fe530000-76 [000] 51.769474: bprint: __dma_tx_complete: tx_size=3
irq/21-fe530000-76 [000] 51.769479: bprint: serial8250_tx_dma: tx_size=4096 fifo_len=4294967293
irq/21-fe530000-76 [000] 51.781295: bprint: __dma_tx_complete: tx_size=4096
irq/21-fe530000-76 [000] 51.781301: bprint: serial8250_tx_dma: tx_size=4096 fifo_len=4294963197
irq/21-fe530000-76 [000] 51.793131: bprint: __dma_tx_complete: tx_size=4096
irq/21-fe530000-76 [000] 51.793135: bprint: serial8250_tx_dma: tx_size=4096 fifo_len=4294959101
irq/21-fe530000-76 [000] 51.804949: bprint: __dma_tx_complete: tx_size=4096
Since the port lock is held in when the kfifo is reset in
uart_flush_buffer() and in __dma_tx_complete(), adding a flush_buffer
hook to adjust the outstanding DMA byte count is sufficient to avoid the
kfifo underflow.
Fixes: 9ee4b83e51f74 ("serial: 8250: Add support for dmaengine")
Cc: stable <stable@kernel.org>
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Link: https://lore.kernel.org/r/20250208124148.1189191-1-jkeeping@inmusicbrands.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As PD2.0 spec ("6.5.6.2 PSSourceOffTimer")，the PSSourceOffTimer is
used by the Policy Engine in Dual-Role Power device that is currently
acting as a Sink to timeout on a PS_RDY Message during a Power Role
Swap sequence. This condition leads to a Hard Reset for USB Type-A and
Type-B Plugs and Error Recovery for Type-C plugs and return to USB
Default Operation.
Therefore, after PSSourceOffTimer timeout, the tcpm state machine should
switch from PR_SWAP_SNK_SRC_SINK_OFF to ERROR_RECOVERY. This can also
solve the test items in the USB power delivery compliance test:
TEST.PD.PROT.SNK.12 PR_Swap – PSSourceOffTimer Timeout
[1] https://usb.org/document-library/usb-power-delivery-compliance-test-specification-0/USB_PD3_CTS_Q4_2025_OR.zip
Fixes: f0690a25a140 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable <stable@kernel.org>
Signed-off-by: Jos Wang <joswang@lenovo.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Amit Sunil Dhamne <amitsd@google.com>
Link: https://lore.kernel.org/r/20250213134921.3798-1-joswang1221@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The role switch registration and set_role() can happen in parallel as they
are invoked independent of each other. There is a possibility that a driver
might spend significant amount of time in usb_role_switch_register() API
due to the presence of time intensive operations like component_add()
which operate under common mutex. This leads to a time window after
allocating the switch and before setting the registered flag where the set
role notifications are dropped. Below timeline summarizes this behavior
Thread1 | Thread2
usb_role_switch_register() |
| |
---> allocate switch |
| |
---> component_add() | usb_role_switch_set_role()
| | |
| | --> Drop role notifications
| | since sw->registered
| | flag is not set.
| |
--->Set registered flag.|
To avoid this, set the registered flag early on in the switch register
API.
Fixes: b787a3e78175 ("usb: roles: don't get/set_role() when usb_role_switch is unregistered")
Cc: stable <stable@kernel.org>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250206193950.22421-1-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The behaviour of kthread_create_worker() was recently changed to align
with the one of kthread_create(). The kthread worker is created but not
awaken by default. This is to allow the use of kthread_affine_preferred()
and kthread_bind[_mask]() with kthread workers. In order to keep the
old behaviour and wake the kthread up, kthread_run_worker() must be
used. All the pre-existing users have been converted, except for UVC
that was introduced in the same merge window as the API change.
This results in hangs:
INFO: task UVCG:82 blocked for more than 491 seconds.
Tainted: G T 6.13.0-rc2-00014-gb04e317b5226 #1
task:UVCG state:D stack:0 pid:82
Call Trace:
__schedule
schedule
schedule_preempt_disabled
kthread
? kthread_flush_work
ret_from_fork
ret_from_fork_asm
entry_INT80_32
Fix this with converting UVCG kworker to the new API.
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202502121025.55bfa801-lkp@intel.com
Fixes: f0bbfbd16b3b ("usb: gadget: uvc: rework to enqueue in pump worker from encoded queue")
Cc: stable <stable@kernel.org>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20250212135514.30539-1-frederic@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Teclast disk used on Huawei hisi platforms doesn't work well,
losing connectivity intermittently if LPM is enabled.
Add quirk disable LPM to resolve the issue.
Signed-off-by: Lei Huang <huanglei@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250212093829.7379-1-huanglei814@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
device_del() can lead to new work being scheduled in gadget->work
workqueue. This is observed, for example, with the dwc3 driver with the
following call stack:
device_del()
gadget_unbind_driver()
usb_gadget_disconnect_locked()
dwc3_gadget_pullup()
dwc3_gadget_soft_disconnect()
usb_gadget_set_state()
schedule_work(&gadget->work)
Move flush_work() after device_del() to ensure the workqueue is cleaned
up.
Fixes: 5702f75375aa9 ("usb: gadget: udc-core: move sysfs_notify() to a workqueue")
Cc: stable <stable@kernel.org>
Signed-off-by: Roy Luo <royluo@google.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250204233642.666991-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When using USB MIDI, a lock is attempted to be acquired twice through a
re-entrant call to f_midi_transmit, causing a deadlock.
Fix it by using queue_work() to schedule the inner f_midi_transmit() via
a high priority work queue from the completion handler.
Link: https://lore.kernel.org/all/CAArt=LjxU0fUZOj06X+5tkeGT+6RbXzpWg1h4t4Fwa_KGVAX6g@mail.gmail.com/
Fixes: d5daf49b58661 ("USB: gadget: midi: add midi function driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Jill Donahue <jilliandonahue58@gmail.com>
Link: https://lore.kernel.org/r/20250211174805.1369265-1-jdonahue@fender.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When usb_control_msg is used in the get_bMaxPacketSize0 function, the
USB pipe does not include the endpoint device number. This can cause
failures when a usb hub port is reinitialized after encountering a bad
cable connection. As a result, the system logs the following error
messages:
usb usb2-port1: cannot reset (err = -32)
usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
usb usb2-port1: attempt power cycle
usb 2-1: new high-speed USB device number 5 using ci_hdrc
usb 2-1: device descriptor read/8, error -71
The problem began after commit 85d07c556216 ("USB: core: Unite old
scheme and new scheme descriptor reads"). There
usb_get_device_descriptor was replaced with get_bMaxPacketSize0. Unlike
usb_get_device_descriptor, the get_bMaxPacketSize0 function uses the
macro usb_rcvaddr0pipe, which does not include the endpoint device
number. usb_get_device_descriptor, on the other hand, used the macro
usb_rcvctrlpipe, which includes the endpoint device number.
By modifying the get_bMaxPacketSize0 function to use usb_rcvctrlpipe
instead of usb_rcvaddr0pipe, the issue can be resolved. This change will
ensure that the endpoint device number is included in the USB pipe,
preventing reinitialization failures. If the endpoint has not set the
device number yet, it will still work because the device number is 0 in
udev.
Cc: stable <stable@kernel.org>
Fixes: 85d07c556216 ("USB: core: Unite old scheme and new scheme descriptor reads")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250203105840.17539-1-eichest@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a frequent timeout during controller enter/exit from halt state
after toggling the run_stop bit by SW. This timeout occurs when
performing frequent role switches between host and device, causing
device enumeration issues due to the timeout. This issue was not present
when USB2 suspend PHY was disabled by passing the SNPS quirks
(snps,dis_u2_susphy_quirk and snps,dis_enblslpm_quirk) from the DTS.
However, there is a requirement to enable USB2 suspend PHY by setting of
GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY bits when controller starts
in gadget or host mode results in the timeout issue.
This commit addresses this timeout issue by ensuring that the bits
GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY are cleared before starting
the dwc3_gadget_run_stop sequence and restoring them after the
dwc3_gadget_run_stop sequence is completed.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250201163903.459-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The fastboot tool for communicating with Android bootloaders does not
work reliably with this device if USB 2 Link Power Management (LPM)
is enabled.
Various fastboot commands are affected, including the
following, which usually reproduces the problem within two tries:
fastboot getvar kernel
getvar:kernel FAILED (remote: 'GetVar Variable Not found')
This issue was hidden on many systems up until commit 63a1f8454962
("xhci: stored cached port capability values in one place") as the xhci
driver failed to detect USB 2 LPM support if USB 3 ports were listed
before USB 2 ports in the "supported protocol capabilities".
Adding the quirk resolves the issue. No drawbacks are expected since
the device uses different USB product IDs outside of fastboot mode, and
since fastboot commands worked before, until LPM was enabled on the
tested system by the aforementioned commit.
Based on a patch from Forest <forestix@nom.one> from which most of the
code and commit message is taken.
Cc: stable <stable@kernel.org>
Reported-by: Forest <forestix@nom.one>
Closes: https://lore.kernel.org/hk8umj9lv4l4qguftdq1luqtdrpa1gks5l@sonic.net
Tested-by: Forest <forestix@nom.one>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250206151836.51742-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add Renesas R-Car D3 USB Download mode quirk and update comments
on all the other Renesas R-Car USB Download mode quirks to discern
them from each other. This follows R-Car Series, 3rd Generation
reference manual Rev.2.00 chapter 19.2.8 USB download mode .
Fixes: 6d853c9e4104 ("usb: cdc-acm: Add DISABLE_ECHO for Renesas USB Download mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250209145708.106914-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If we receive an initial fragment of size 8 bytes which specifies a wLength
of 1 byte (so the reassembled message is supposed to be 9 bytes long), and
we then receive a second fragment of size 9 bytes (which is not supposed to
happen), we currently wrongly bypass the fragment reassembly code but still
pass the pointer to the acm->notification_buffer to
acm_process_notification().
Make this less wrong by always going through fragment reassembly when we
expect more fragments.
Before this patch, receiving an overlong fragment could lead to `newctrl`
in acm_process_notification() being uninitialized data (instead of data
coming from the device).
Cc: stable <stable@kernel.org>
Fixes: ea2583529cd1 ("cdc-acm: reassemble fragmented notifications")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Miao Li
Michal Pecio
Thinh Nguyen
Pawel Laszczak
Claudiu Beznea
Badhri Jagan Sridharan
Prashanth K
Marc Zyngier
Marek Szyprowski
Fedor Pchelkin
Christian A. Ehrhardt
AngeloGioacchino Del Regno
Nikita Zhandarovich
Linus Torvalds
Steven Rostedt
Uwe Kleine-König
Thomas Weißschuh
Masahiro Yamada
Ashish Kalra
Sean Christopherson
Thorsten Blum
Ivan Kokshaysky
Jann Horn
John Keeping
Jos Wang
Elson Roy Serrao
Frederic Weisbecker
Lei Huang
Roy Luo
Jill Donahue
Stefan Eichenberger
Selvarasu Ganesan
Mathias Nyman
Marek Vasut