| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In this code, if devm_add_action_or_reset() fails, it will call
max1720x_unregister_ancillary() which in turn calls
i2c_unregister_device(). Thus the call to i2c_unregister_device() on the
following line is not required and is a double unregister. Delete it.
Fixes: 47271a935619 ("power: supply: max1720x: add read support for nvmem")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/9c2f76e7-5679-473b-9b9c-e11b492b96ac@stanley.mountain
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add support for the AXP717 PMIC battery charger. The AXP717 differs
greatly from existing AXP battery chargers in that it cannot measure
the discharge current. The datasheet does not document the current
value's offset or scale, so the POWER_SUPPLY_PROP_CURRENT_NOW is left
unscaled.
Tested-by: Philippe Simons <simons.philippe@gmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240821215456.962564-15-macroalpha82@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add support for the AXP717 PMIC. The AXP717 PMIC allows for detection
of USB type like the AXP813, but has little in common otherwise with
the other AXP PMICs. The USB charger is able to provide between
100000uA and 3250000uA of power, and can measure the VBUS input in mV
with up to 14 bits of precision.
Tested-by: Philippe Simons <simons.philippe@gmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240821215456.962564-14-macroalpha82@gmail.com
[fix axp717_usb_power_desc.usb_types]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add binding information for AXP717.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20240821215456.962564-11-macroalpha82@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add support for the AXP717. It has BC 1.2 detection like the AXP813
and uses ADC channels like all other AXP devices, but otherwise is
very different requiring new registers for most functions.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240821215456.962564-10-macroalpha82@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
There is a spelling mistake in a dev_warn message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20240828093447.271503-1-colin.i.king@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The bit_types array just hold a list of valid enum power_supply_usb_type
values which map to 0 - 9. This can easily be represented as a bitmap.
This reduces the size of struct power_supply_desc and further reduces
the data section size by drivers no longer needing to store the array.
This also unifies how usb_types are handled with charge_behaviours,
which allows power_supply_show_usb_type() to be removed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240831142039.28830-7-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Move power_supply_show_enum_with_available() higher up in
the power_supply_sysfs.c file.
This is a preparation patch to avoid needing a forward declaration
when replacing power_supply_show_usb_type() with it later on.
This commit only moves the function, there are no changes to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240831142039.28830-6-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Turn power_supply_charge_behaviour_show() into a generic function for
showing enum values with their available (for writing) values shown
and the current value shown surrounded by sqaure-brackets like
the show() output for "usb_type" and "charge_behaviour".
This is a preparation patch for refactoring the "usb_type" property
handling to use a bitmask indicating available usb-types + this new
generic function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240831142039.28830-5-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The "usb_type" property must be read-only for charger power-supply devices,
see: Documentation/ABI/testing/sysfs-class-power.
But the rt9467 driver allows writing 0/1 to it to disable/enable charging.
Other charger drivers use the "status" property for this and the rt9467
code also allows writing 0/1 to its "status" property and this does
the exact same thing as writing 0/1 to its "usb_type" property.
Drop write support for the "usb_type" property making it readonly to match
the ABI documentation. If userspace wants to disable/enable charging it
can use the "status" property for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240831142039.28830-4-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
power_supply_sysfs.c accept wrrites of strings to "usb_type" for strings
values matching an entry in POWER_SUPPLY_USB_TYPE_TEXT[]. If such a
string value is written then the int value passed to ucs1002_set_property()
will be an enum power_supply_usb_type value.
Before this change ucs1002_set_usb_type() expected the value to be an index
into ucs1002_usb_types[]. Adjust ucs1002_set_usb_type() to use the enum
value directly so that writing string values works.
The list of supported types in ucs1002_usb_types[] is: PD, SDP, DCP, CDP.
The [POWER_SUPPLY_USB_TYPE_]SDP, DCP and CDP enum labels have a value of
1, 2 and 3. So userspace selecting SDP, DCP or CDP by writing 1, 2 or 3
will keep working. POWER_SUPPLY_USB_TYPE_PD which is mapped to the ucs1002
dedicated mode however has a value of 6. Before this change writing 0 would
select the dedicated mode. To preserve userspace API compatibility also map
POWER_SUPPLY_USB_TYPE_UNKNOWN (which is 0) to the dedicated mode.
Cc: Enric Balletbo Serra <enric.balletbo@collabora.com>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240831142039.28830-3-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
According to Documentation/ABI/testing/sysfs-class-power the "usb_type"
property is Read-Only.
For power-supplies which consume USB power such as battery charger chips,
this is correct.
But the UCS1002 USB Port Power Controller driver which is a driver
for a chip which is a power-source for USB-A charging ports "usb_type"
is actually writable to configure the type of USB charger emulated
by the USB-A port.
Adjust the docs and the power_supply_sysfs.c code to adjust for this
new writeable use of "usb_type":
1. Update Documentation/ABI/testing/sysfs-class-power to document that
"usb_type" may be writable
2. Change the power_supply_attr type in power_supply_sysfs.c from
POWER_SUPPLY_ATTR() into POWER_SUPPLY_ENUM_ATTR() so that the various
usb_type string values from POWER_SUPPLY_TYPE_TEXT[] such as e.g.
"SDP" and "USB_PD" can be written to the "usb_type" attribute instead
of only accepting integer values.
Cc: Enric Balletbo Serra <enric.balletbo@collabora.com>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240831142039.28830-2-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
ModelGauge m5 and device configuration values are stored in nonvolatile
memory to prevent data loss if the IC loses power. Add read support for
the nonvolatile memory on MAX1720X devices.
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Link: https://lore.kernel.org/r/20240903063526.222890-1-dima.fedrau@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add support for the AXP717 PMIC to utilize the ADC (for reading
voltage, current, and temperature information from the PMIC) as well
as the USB charger and battery.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240821215456.962564-12-macroalpha82@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
This struct is never modified, so mark it const.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20240828-power-supply-const-psy_tzd_ops-v1-1-dc27176fda5b@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
There may be other backup reset methods available, do not halt
here so that other reset methods can be tried.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240610142836.168603-5-afd@ti.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Function register_restart_handler() is deprecated. Using this new API
removes our need to keep and manage a struct notifier_block.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240610142836.168603-4-afd@ti.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Simplify probe by fetching the regmap and its arguments in one call.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240610142836.168603-3-afd@ti.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Use device_get_match_data() for finding the matching node and fetching
the match data all in one.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240610142836.168603-2-afd@ti.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The platform_driver_probe() helper is useful when the probe function
is in the _init section, that is not the case here. Use the normal
platform_driver_register() function.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240610142836.168603-1-afd@ti.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The OCP board used a BlueField's GPIO pin for entering
low power mode. That board was not commercialized and
has been dropped from production so all its code is unused.
The new hardware requirement is to trigger a graceful shutdown
when that GPIO pin is toggled. So replace the unused low power
mode with a graceful shutdown.
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/20240611134327.30975-1-asmaa@nvidia.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://lore.kernel.org/r/20240710032023.2003742-1-nichen@iscas.ac.cn
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
There are two charger current limit registers:
- Fast charge current limit (which controls current going from the
charger to the battery);
- CHGIN input current limit (which controls current going into the
charger through the cable).
Add the necessary functions to retrieve the CHGIN input limit (from CHARGER
regulator) and maximum fast charge current values, and expose them as power
supply properties.
Tested-by: Henrik Grimler <henrik@grimler.se>
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240816-max77693-charger-extcon-v4-3-050a0a9bfea0@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Commit 223a3b82834f ("power: supply: max17042_battery: use VFSOC for
capacity when no rsns") made it so that capacity on systems without
current sensing would be read from VFSOC instead of RepSOC. However,
the SOC threshold calculation still read RepSOC to get the SOC
regardless of the current sensing option state.
Fix this by applying the same conditional to determine which register
should be read.
This also seems to be the intended behavior as per the datasheet - SOC
alert config value in MiscCFG on setups without current sensing is set
to a value of 0b11, indicating SOC alerts being generated based on
VFSOC, instead of 0b00 which indicates SOC alerts being generated based
on RepSOC.
This fixes an issue on the Galaxy S3/Midas boards, where the alert
interrupt would be constantly retriggered, causing high CPU usage
on idle (around ~12%-15%).
Fixes: e5f3872d2044 ("max17042: Add support for signalling change in SOC")
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240817-max17042-soc-threshold-fix-v1-1-72b45899c3cc@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Document the monitored-battery property, which the existing driver can
use to set certain properties.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240821215456.962564-8-macroalpha82@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Allow users to specify a maximum input current for the device. Some
devices allow up to 3.25A of input current (such as the AXP717), which
may be too much for some implementations.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240821215456.962564-7-macroalpha82@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Allow specifying a hard limit of the maximum input current. Some PMICs
such as the AXP717 can pull up to 3.25A, so allow a value to be
specified that clamps this in the event the hardware is not designed
for it.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240821215456.962564-6-macroalpha82@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Make reading of the vbus value and configuring of the iio channels
device specific, to allow additional devices (such as the AXP717) to
be supported by this driver.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240821215456.962564-5-macroalpha82@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Move the configuration of battery specific information and available
iio channels from the probe function to a device specific routine,
allowing us to use this driver for devices with slightly different
configurations (such as the AXP717).
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240821215456.962564-4-macroalpha82@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN and
POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN values should be immutable
properties of the battery, but for this driver they are writable values
and used as the minimum and maximum values for charging. Remove the
DESIGN designation from these values.
Fixes: 46c202b5f25f ("power: supply: add battery driver for AXP20X and AXP22X PMICs")
Suggested-by: Chen-Yu Tsai <wens@kernel.org>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240821215456.962564-3-macroalpha82@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Driver reads existing current value from two 8-bit registers, but then
compares only one of them with the new 16-bit value. clang W=1 is also
not happy:
twl4030_charger.c:243:16: error: variable 'cur_reg' set but not used [-Werror,-Wunused-but-set-variable]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240705113113.42851-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Allocate the memory with scoped/cleanup.h to reduce error handling and
make the code a bit simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240705113113.42851-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The SC27XX fuel gauge supports a low voltage alarm IRQ, which is used
for more accurate battery capacity measurements with lower voltages.
This was unfortunately never documented in bindings, do so now.
The only in-tree user (sc2731.dtsi) has had interrupts specified
since its initial fuel-gauge submission and the current kernel
driver returns an error when no interrupt is specified, so also
add it to the required list.
Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/Zr3SAHlq5A78QvrW@standask-GA-A55M-S2HP
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from platform_device_id table.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20240819040831.2801543-1-ruanjinjie@huawei.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The existing docs here are a bit vague. This reformats and rewords it,
and is based upon the wording originally used by the dell-laptop driver
battery documentation and also sysfs-class-power-wilco.
The wording for "Long Life" and "Bypass" remain the same, because I'm
unfamiliar with hardware that use them.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240820041942.30ed42f3@5400
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
|
|
This simplifies the min_t() and max_t() macros by no longer making them
work in the context of a C constant expression.
That means that you can no longer use them for static initializers or
for array sizes in type definitions, but there were only a couple of
such uses, and all of them were converted (famous last words) to use
MIN_T/MAX_T instead.
Cc: David Laight <David.Laight@aculab.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 3a7e02c040b1 ("minmax: avoid overly complicated constant
expressions in VM code") added the simpler MIN_T/MAX_T macros in order
to avoid some excessive expansion from the rather complicated regular
min/max macros.
The complexity of those macros stems from two issues:
(a) trying to use them in situations that require a C constant
expression (in static initializers and for array sizes)
(b) the type sanity checking
and MIN_T/MAX_T avoids both of these issues.
Now, in the whole (long) discussion about all this, it was pointed out
that the whole type sanity checking is entirely unnecessary for
min_t/max_t which get a fixed type that the comparison is done in.
But that still leaves min_t/max_t unnecessarily complicated due to
worries about the C constant expression case.
However, it turns out that there really aren't very many cases that use
min_t/max_t for this, and we can just force-convert those.
This does exactly that.
Which in turn will then allow for much simpler implementations of
min_t()/max_t(). All the usual "macros in all upper case will evaluate
the arguments multiple times" rules apply.
We should do all the same things for the regular min/max() vs MIN/MAX()
cases, but that has the added complexity of various drivers defining
their own local versions of MIN/MAX, so that needs another level of
fixes first.
Link: https://lore.kernel.org/all/b47fad1d0cf8449886ad148f8c013dae@AcuMS.aculab.com/
Cc: David Laight <David.Laight@aculab.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
After a recent change in clang to stop consuming all instances of '-S'
and '-c' [1], the stack protector scripts break due to the kernel's use
of -Werror=unused-command-line-argument to catch cases where flags are
not being properly consumed by the compiler driver:
$ echo | clang -o - -x c - -S -c -Werror=unused-command-line-argument
clang: error: argument unused during compilation: '-c' [-Werror,-Wunused-command-line-argument]
This results in CONFIG_STACKPROTECTOR getting disabled because
CONFIG_CC_HAS_SANE_STACKPROTECTOR is no longer set.
'-c' and '-S' both instruct the compiler to stop at different stages of
the pipeline ('-S' after compiling, '-c' after assembling), so having
them present together in the same command makes little sense. In this
case, the test wants to stop before assembling because it is looking at
the textual assembly output of the compiler for either '%fs' or '%gs',
so remove '-c' from the list of arguments to resolve the error.
All versions of GCC continue to work after this change, along with
versions of clang that do or do not contain the change mentioned above.
Cc: stable@vger.kernel.org
Fixes: 4f7fd4d7a791 ("[PATCH] Add the -fstack-protector option to the CFLAGS")
Fixes: 60a5317ff0f4 ("x86: implement x86_32 stack protector")
Link: https://github.com/llvm/llvm-project/commit/6461e537815f7fa68cef06842505353cf5600e9c [1]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Since ubiblock_exit() is now called from an init function,
the __exit section no longer makes sense.
Cc: Ben Hutchings <bwh@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202407131403.wZJpd8n2-lkp@intel.com/
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
|
|
In the same way as for other similar files, mark as ghost the new file
generated by depmod for configured weak dependencies for modules,
modules.weakdep, so that although it is not included in the package,
claim the ownership on it.
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
hostfs not keep the host directory when mounting. When the host
directory is none (default), fc->source is used as the host root
directory, and this is wrong. Here we use `parse_monolithic` to
handle the old mount path for parsing the root directory. For new
mount path, The `parse_param` is used for the host directory parse.
Reported-and-tested-by: Maciej Żenczykowski <maze@google.com>
Fixes: cd140ce9f611 ("hostfs: convert hostfs to use the new mount API")
Link: https://lore.kernel.org/all/CANP3RGceNzwdb7w=vPf5=7BCid5HVQDmz1K5kC9JG42+HVAh_g@mail.gmail.com/
Cc: Christian Brauner <brauner@kernel.org>
Signed-off-by: Hongbo Li <lihongbo22@huawei.com>
Link: https://lore.kernel.org/r/20240725065130.1821964-1-lihongbo22@huawei.com
[brauner: minor fixes]
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Christian noticed that it is possible for a privileged user to mount
most filesystems with a non-initial user namespace in sb->s_user_ns.
When fsopen() is called in a non-init namespace the caller's namespace
is recorded in fs_context->user_ns. If the returned file descriptor is
then passed to a process priviliged in init_user_ns, that process can
call fsconfig(fd_fs, FSCONFIG_CMD_CREATE), creating a new superblock
with sb->s_user_ns set to the namespace of the process which called
fsopen().
This is problematic. We cannot assume that any filesystem which does not
set FS_USERNS_MOUNT has been written with a non-initial s_user_ns in
mind, increasing the risk for bugs and security issues.
Prevent this by returning EPERM from sget_fc() when FS_USERNS_MOUNT is
not set for the filesystem and a non-initial user namespace will be
used. sget() does not need to be updated as it always uses the user
namespace of the current context, or the initial user namespace if
SB_SUBMOUNT is set.
Fixes: cb50b348c71f ("convenience helpers: vfs_get_super() and sget_fc()")
Reported-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Seth Forshee (DigitalOcean) <sforshee@kernel.org>
Link: https://lore.kernel.org/r/20240724-s_user_ns-fix-v1-1-895d07c94701@kernel.org
Reviewed-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
In a commit 1d717123bb1a ("ALSA: firewire-lib: Avoid
-Wflex-array-member-not-at-end warning"), DEFINE_FLEX() macro was used to
handle variable length of array for header field in struct fw_iso_packet
structure. The usage of macro has a side effect that the designated
initializer assigns the count of array to the given field. Therefore
CIP_HEADER_QUADLETS (=2) is assigned to struct fw_iso_packet.header,
while the original designated initializer assigns zero to all fields.
With CIP_NO_HEADER flag, the change causes invalid length of header in
isochronous packet for 1394 OHCI IT context. This bug affects all of
devices supported by ALSA fireface driver; RME Fireface 400, 800, UCX, UFX,
and 802.
This commit fixes the bug by replacing it with the alternative version of
macro which corresponds no initializer.
Cc: stable@vger.kernel.org
Fixes: 1d717123bb1a ("ALSA: firewire-lib: Avoid -Wflex-array-member-not-at-end warning")
Reported-by: Edmund Raile <edmund.raile@proton.me>
Closes: https://lore.kernel.org/r/rrufondjeynlkx2lniot26ablsltnynfaq2gnqvbiso7ds32il@qk4r6xps7jh2/
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240725155640.128442-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
|
|
This reverts commit d3155742db89df3b3c96da383c400e6ff4d23c25.
The header_length field is byte unit, thus it can not express the number of
elements in header field. It seems that the argument for counted_by
attribute can have no arithmetic expression, therefore this commit just
reverts the issued commit.
Suggested-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20240725161648.130404-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
|
|
The minmax infrastructure is overkill for simple constants, and can
cause huge expansions because those simple constants are then used by
other things.
For example, 'pageblock_order' is a core VM constant, but because it was
implemented using 'min_t()' and all the type-checking that involves, it
actually expanded to something like 2.5kB of preprocessor noise.
And when that simple constant was then used inside other expansions:
#define pageblock_nr_pages (1UL << pageblock_order)
#define pageblock_start_pfn(pfn) ALIGN_DOWN((pfn), pageblock_nr_pages)
and we then use that inside a 'max()' macro:
case ISOLATE_SUCCESS:
update_cached = false;
last_migrated_pfn = max(cc->zone->zone_start_pfn,
pageblock_start_pfn(cc->migrate_pfn - 1));
the end result was that one statement expanding to 253kB in size.
There are probably other cases of this, but this one case certainly
stood out.
I've added 'MIN_T()' and 'MAX_T()' macros for this kind of "core simple
constant with specific type" use. These macros skip the type checking,
and as such need to be very sparingly used only for obvious cases that
have active issues like this.
Reported-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Link: https://lore.kernel.org/all/36aa2cad-1db1-4abf-8dd2-fb20484aabc3@lucifer.local/
Cc: David Laight <David.Laight@aculab.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We have some very fancy min/max macros that have tons of sanity checking
to warn about mixed signedness etc.
This is all things that a sane compiler should warn about, but there are
no sane compiler interfaces for this, and '-Wsign-compare' is broken [1]
and not useful.
So then we compensate (some would say over-compensate) by doing the
checks manually with some truly horrid macro games.
And no, we can't just use __builtin_types_compatible_p(), because the
whole question of "does it make sense to compare these two values" is a
lot more complicated than that.
For example, it makes a ton of sense to compare unsigned values with
simple constants like "5", even if that is indeed a signed type. So we
have these very strange macros to try to make sensible type checking
decisions on the arguments to 'min()' and 'max()'.
But that can cause enormous code expansion if the min()/max() macros are
used with complicated expressions, and particularly if you nest these
things so that you get the first big expansion then expanded again.
The xen setup.c file ended up ballooning to over 50MB of preprocessed
noise that takes 15s to compile (obviously depending on the build host),
largely due to one single line.
So let's split that one single line to just be simpler. I think it ends
up being more legible to humans too at the same time. Now that single
file compiles in under a second.
Reported-and-reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Link: https://lore.kernel.org/all/c83c17bb-be75-4c67-979d-54eee38774c6@lucifer.local/
Link: https://staticthinking.wordpress.com/2023/07/25/wsign-compare-is-garbage/ [1]
Cc: David Laight <David.Laight@aculab.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Syzbot reported that a buffer state inconsistency was detected in
nilfs_btnode_create_block(), triggering a kernel bug.
It is not appropriate to treat this inconsistency as a bug; it can occur
if the argument block address (the buffer index of the newly created
block) is a virtual block number and has been reallocated due to
corruption of the bitmap used to manage its allocation state.
So, modify nilfs_btnode_create_block() and its callers to treat it as a
possible filesystem error, rather than triggering a kernel bug.
Link: https://lkml.kernel.org/r/20240725052007.4562-1-konishi.ryusuke@gmail.com
Fixes: a60be987d45d ("nilfs2: B-tree node cache")
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+89cc4f2324ed37988b60@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=89cc4f2324ed37988b60
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Post my improvement of the test in e4a4ba415419 ("selftests/mm:
va_high_addr_switch: dynamically initialize testcases to enable LPA2
testing"):
The test begins to fail on 4k and 16k pages, on non-LPA2 systems. To
reduce noise in the CI systems, let us skip the test when higher address
space is not implemented.
Link: https://lkml.kernel.org/r/20240718052504.356517-1-dev.jain@arm.com
Fixes: e4a4ba415419 ("selftests/mm: va_high_addr_switch: dynamically initialize testcases to enable LPA2 testing")
Signed-off-by: Dev Jain <dev.jain@arm.com>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
It's expected that no page should be left in pcp_list after calling
zone_pcp_disable() in offline_pages(). Previously, it's observed that
offline_pages() gets stuck [1] due to some pages remaining in pcp_list.
Cause:
There is a race condition between drain_pages_zone() and __rmqueue_pcplist()
involving the pcp->count variable. See below scenario:
CPU0 CPU1
---------------- ---------------
spin_lock(&pcp->lock);
__rmqueue_pcplist() {
zone_pcp_disable() {
/* list is empty */
if (list_empty(list)) {
/* add pages to pcp_list */
alloced = rmqueue_bulk()
mutex_lock(&pcp_batch_high_lock)
...
__drain_all_pages() {
drain_pages_zone() {
/* read pcp->count, it's 0 here */
count = READ_ONCE(pcp->count)
/* 0 means nothing to drain */
/* update pcp->count */
pcp->count += alloced << order;
...
...
spin_unlock(&pcp->lock);
In this case, after calling zone_pcp_disable() though, there are still some
pages in pcp_list. And these pages in pcp_list are neither movable nor
isolated, offline_pages() gets stuck as a result.
Solution:
Expand the scope of the pcp->lock to also protect pcp->count in
drain_pages_zone(), to ensure no pages are left in the pcp list after
zone_pcp_disable()
[1] https://lore.kernel.org/linux-mm/6a07125f-e720-404c-b2f9-e55f3f166e85@fujitsu.com/
Link: https://lkml.kernel.org/r/20240723064428.1179519-1-lizhijian@fujitsu.com
Fixes: 4b23a68f9536 ("mm/page_alloc: protect PCP lists with a spinlock")
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Reported-by: Yao Xingtao <yaoxt.fnst@fujitsu.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Cc: David Hildenbrand <david@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
Dan Carpenter
Chris Morgan
Colin Ian King
Hans de Goede
Dimitri Fedrau
Thomas Weißschuh
Andrew Davis
Asmaa Mnebhi
Chen Ni
Artur Weber
Krzysztof Kozlowski
Stanislav Jakubek
Jinjie Ruan
Andres Salomon
Linus Torvalds
Nathan Chancellor
Richard Weinberger
Jose Ignacio Tornos Martinez
Hongbo Li
Seth Forshee (DigitalOcean)
Takashi Sakamoto
Ryusuke Konishi
Dev Jain
Li Zhijian