| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Quirk is needed to enable headset microphone on missing pin 0x19.
Signed-off-by: Christoffer Sandberg <cs@tuxedo.de>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20241029151653.80726-2-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Quirk is needed to enable headset microphone on missing pin 0x19.
Signed-off-by: Christoffer Sandberg <cs@tuxedo.de>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20241029151653.80726-1-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The WD19 family of docks has the same audio chipset as the WD15. This
change enables jack detection on the WD19.
We don't need the dell_dock_mixer_init quirk for the WD19. It is only
needed because of the dell_alc4020_map quirk for the WD15 in
mixer_maps.c, which disables the volume controls. Even for the WD15,
this quirk was apparently only needed when the dock firmware was not
updated.
Signed-off-by: Jan Schär <jan@jschaer.ch>
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20241029221249.15661-1-jan@jschaer.ch
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
On a system with wcd937x, rxmacro and Qualcomm audio DSP, which is pretty
common set of devices on Qualcomm platforms, and due to the order of how
DAPM widgets are powered on (they are sorted), there is a small time window
when wcd937x chip is online and expects the flow of incoming data but
rxmacro is not yet online. When wcd937x is programmed to receive data
via AUX port then its AUX PDM watchdog is enabled in
wcd937x_codec_enable_aux_pa(). If due to some reasons the rxmacro and
soundwire machinery are delayed to start streaming data, then there is
a chance for this AUX PDM watchdog to reset the wcd937x codec. Such event
is not logged as a message and only wcd937x IRQ counter is increased
however there could be a lot of other reasons for that IRQ.
There is a similar opportunity for such delay during DAPM widgets power
down sequence.
If wcd937x codec reset happens on the start of the playback, then there
will be no sound and if such reset happens at the end of a playback then
it may generate additional clicks and pops noises.
On qrb4210 RB2 board without any debugging bits the wcd937x resets are
sometimes observed at the end of a playback though not always.
With some debugging messages or with some tracing enabled the AUX PDM
watchdog resets the wcd937x codec at the start of a playback and there
is no sound output at all.
In this patch:
- TIMEOUT_SEL bit in PDM_WD_CTL2 register is set to increase the watchdog
reset delay to 100ms which eliminates the AUX PDM watchdog IRQs on
qrb4210 RB2 board completely and decreases the number of unwanted clicks
noises;
- HOLD_OFF bit postpones triggering such watchdog IRQ till wcd937x codec
reset which usually happens at the end of a playback. This allows to
actually output some sound in case of debugging.
Cc: Adam Skladowski <a39.skl@gmail.com>
Cc: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Cc: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Link: https://patch.msgid.link/20241022033132.787416-3-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The wcd937x supports also AUX input but the control that sets correct
soundwire port for this is missing. This control is required for audio
playback, for instance, on qrb4210 RB2 board as well as on other
SoCs.
Reported-by: Adam Skladowski <a39.skl@gmail.com>
Reported-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Suggested-by: Adam Skladowski <a39.skl@gmail.com>
Suggested-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Link: https://patch.msgid.link/20241022033132.787416-2-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix DTB warnings when rk3308-codec used with audio-graph-card by
documenting port property:
codec@ff560000: 'port' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Dmitry Yashin <dmt.yashin@gmail.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patch.msgid.link/20241028213314.476776-2-dmt.yashin@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch addresses an issue introduced by commit 1a83a716ec233 ("mm:
krealloc: consider spare memory for __GFP_ZERO") which causes MTE
(Memory Tagging Extension) to falsely report a slab-out-of-bounds error.
The problem occurs when zeroing out spare memory in __do_krealloc. The
original code only considered software-based KASAN and did not account
for MTE. It does not reset the KASAN tag before calling memset, leading
to a mismatch between the pointer tag and the memory tag, resulting
in a false positive.
Example of the error:
==================================================================
swapper/0: BUG: KASAN: slab-out-of-bounds in __memset+0x84/0x188
swapper/0: Write at addr f4ffff8005f0fdf0 by task swapper/0/1
swapper/0: Pointer tag: [f4], memory tag: [fe]
swapper/0:
swapper/0: CPU: 4 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.12.
swapper/0: Hardware name: MT6991(ENG) (DT)
swapper/0: Call trace:
swapper/0: dump_backtrace+0xfc/0x17c
swapper/0: show_stack+0x18/0x28
swapper/0: dump_stack_lvl+0x40/0xa0
swapper/0: print_report+0x1b8/0x71c
swapper/0: kasan_report+0xec/0x14c
swapper/0: __do_kernel_fault+0x60/0x29c
swapper/0: do_bad_area+0x30/0xdc
swapper/0: do_tag_check_fault+0x20/0x34
swapper/0: do_mem_abort+0x58/0x104
swapper/0: el1_abort+0x3c/0x5c
swapper/0: el1h_64_sync_handler+0x80/0xcc
swapper/0: el1h_64_sync+0x68/0x6c
swapper/0: __memset+0x84/0x188
swapper/0: btf_populate_kfunc_set+0x280/0x3d8
swapper/0: __register_btf_kfunc_id_set+0x43c/0x468
swapper/0: register_btf_kfunc_id_set+0x48/0x60
swapper/0: register_nf_nat_bpf+0x1c/0x40
swapper/0: nf_nat_init+0xc0/0x128
swapper/0: do_one_initcall+0x184/0x464
swapper/0: do_initcall_level+0xdc/0x1b0
swapper/0: do_initcalls+0x70/0xc0
swapper/0: do_basic_setup+0x1c/0x28
swapper/0: kernel_init_freeable+0x144/0x1b8
swapper/0: kernel_init+0x20/0x1a8
swapper/0: ret_from_fork+0x10/0x20
==================================================================
Fixes: 1a83a716ec233 ("mm: krealloc: consider spare memory for __GFP_ZERO")
Signed-off-by: Qun-Wei Lin <qun-wei.lin@mediatek.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
|
|
Infinix ZERO BOOK 13 has a 2+2 speaker system which isn't probed correctly.
This patch adds a quirk with the proper pin connections.
Also The mic in this laptop suffers too high gain resulting in mostly
fan noise being recorded,
This patch Also limit mic boost.
HW Probe for device; https://linux-hardware.org/?probe=a2e892c47b
Test: All 4 speaker works, Mic has low noise.
Signed-off-by: Piyush Raj Chouhan <piyushchouhan1598@gmail.com>
Link: https://patch.msgid.link/20241028155516.15552-1-piyuschouhan1598@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Commit 13ddaf26be32 ("mm/swap: fix race when skipping swapcache")
introduced an unconditional one-tick sleep when `swapcache_prepare()`
fails, which has led to reports of UI stuttering on latency-sensitive
Android devices. To address this, we can use a waitqueue to wake up tasks
that fail `swapcache_prepare()` sooner, instead of always sleeping for a
full tick. While tasks may occasionally be woken by an unrelated
`do_swap_page()`, this method is preferable to two scenarios: rapid
re-entry into page faults, which can cause livelocks, and multiple
millisecond sleeps, which visibly degrade user experience.
Oven's testing shows that a single waitqueue resolves the UI stuttering
issue. If a 'thundering herd' problem becomes apparent later, a waitqueue
hash similar to `folio_wait_table[PAGE_WAIT_TABLE_SIZE]` for page bit
locks can be introduced.
[v-songbaohua@oppo.com: wake_up only when swapcache_wq waitqueue is active]
Link: https://lkml.kernel.org/r/20241008130807.40833-1-21cnbao@gmail.com
Link: https://lkml.kernel.org/r/20240926211936.75373-1-21cnbao@gmail.com
Fixes: 13ddaf26be32 ("mm/swap: fix race when skipping swapcache")
Signed-off-by: Barry Song <v-songbaohua@oppo.com>
Reported-by: Oven Liyang <liyangouwen1@oppo.com>
Tested-by: Oven Liyang <liyangouwen1@oppo.com>
Cc: Kairui Song <kasong@tencent.com>
Cc: "Huang, Ying" <ying.huang@intel.com>
Cc: Yu Zhao <yuzhao@google.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Chris Li <chrisl@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Yosry Ahmed <yosryahmed@google.com>
Cc: SeongJae Park <sj@kernel.org>
Cc: Kalesh Singh <kaleshsingh@google.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Pedro Falcato's optimization [1] for checking sealed VMAs, which replaces
the can_modify_mm() function with an in-loop check, necessitates an update
to the mseal.rst documentation to reflect this change.
Furthermore, the document has received offline comments regarding the code
sample and suggestions for sentence clarification to enhance reader
comprehension.
[1] https://lore.kernel.org/linux-mm/20240817-mseal-depessimize-v3-0-d8d2e037df30@gmail.com/
Update doc after in-loop change: mprotect/madvise can have
partially updated and munmap is atomic.
Fix indentation and clarify some sections to improve readability.
Link: https://lkml.kernel.org/r/20241008040942.1478931-2-jeffxu@chromium.org
Fixes: df2a7df9a9aa ("mm/munmap: replace can_modify_mm with can_modify_vma")
Fixes: 4a2dd02b0916 ("mm/mprotect: replace can_modify_mm with can_modify_vma")
Fixes: 38075679b5f1 ("mm/mremap: replace can_modify_mm with can_modify_vma")
Fixes: 23c57d1fa2b9 ("mseal: replace can_modify_mm_madv with a vma variant")
Signed-off-by: Jeff Xu <jeffxu@chromium.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Elliott Hughes <enh@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: Jann Horn <jannh@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Jorge Lucangeli Obes <jorgelo@chromium.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: "Liam R. Howlett" <Liam.Howlett@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Muhammad Usama Anjum <usama.anjum@collabora.com>
Cc: Pedro Falcato <pedro.falcato@gmail.com>
Cc: Stephen Röttger <sroettger@google.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: "Theo de Raadt" <deraadt@openbsd.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Commit ea7e2d5e49c0 ("mm: call the security_mmap_file() LSM hook in
remap_file_pages()") fixed a security issue, it added an LSM check when
trying to remap file pages, so that LSMs have the opportunity to evaluate
such action like for other memory operations such as mmap() and
mprotect().
However, that commit called security_mmap_file() inside the mmap_lock
lock, while the other calls do it before taking the lock, after commit
8b3ec6814c83 ("take security_mmap_file() outside of ->mmap_sem").
This caused lock inversion issue with IMA which was taking the mmap_lock
and i_mutex lock in the opposite way when the remap_file_pages() system
call was called.
Solve the issue by splitting the critical region in remap_file_pages() in
two regions: the first takes a read lock of mmap_lock, retrieves the VMA
and the file descriptor associated, and calculates the 'prot' and 'flags'
variables; the second takes a write lock on mmap_lock, checks that the VMA
flags and the VMA file descriptor are the same as the ones obtained in the
first critical region (otherwise the system call fails), and calls
do_mmap().
In between, after releasing the read lock and before taking the write
lock, call security_mmap_file(), and solve the lock inversion issue.
Link: https://lkml.kernel.org/r/20241018161415.3845146-1-roberto.sassu@huaweicloud.com
Fixes: ea7e2d5e49c0 ("mm: call the security_mmap_file() LSM hook in remap_file_pages()")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reported-by: syzbot+1cd571a672400ef3a930@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-security-module/66f7b10e.050a0220.46d20.0036.GAE@google.com/
Tested-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Jann Horn <jannh@google.com>
Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@Oracle.com>
Reviewed-by: Paul Moore <paul@paul-moore.com>
Tested-by: syzbot+1cd571a672400ef3a930@syzkaller.appspotmail.com
Cc: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Dmitry Kasatkin <dmitry.kasatkin@gmail.com>
Cc: Eric Snowberg <eric.snowberg@oracle.com>
Cc: James Morris <jmorris@namei.org>
Cc: Mimi Zohar <zohar@linux.ibm.com>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Shu Han <ebpqwerty472123@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Some additional synchronization is needed on Android ARM64; we see a
deadlock with pthread_create when the parent thread races forward before
the child has a chance to start doing work.
Link: https://lkml.kernel.org/r/20241018171734.2315053-4-edliaw@google.com
Fixes: cff294582798 ("selftests/mm: extend and rename uffd pagemap test")
Signed-off-by: Edward Liaw <edliaw@google.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
This reverts commit e61ef21e27e8deed8c474e9f47f4aa7bc37e138c.
uffd_poll_thread may be called by other tests that do not initialize the
pthread_barrier, so this approach is not correct. This will revert to
using atomic_bool instead.
Link: https://lkml.kernel.org/r/20241018171734.2315053-3-edliaw@google.com
Fixes: e61ef21e27e8 ("selftests/mm: replace atomic_bool with pthread_barrier_t")
Signed-off-by: Edward Liaw <edliaw@google.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Patch series "selftests/mm: revert pthread_barrier change"
On Android arm, pthread_create followed by a fork caused a deadlock in
the case where the fork required work to be completed by the created
thread.
The previous patches incorrectly assumed that the parent would
always initialize the pthread_barrier for the child thread. This
reverts the change and replaces the fix for wp-fork-with-event with the
original use of atomic_bool.
This patch (of 3):
This reverts commit e142cc87ac4ec618f2ccf5f68aedcd6e28a59d9d.
fork_event_consumer may be called by other tests that do not initialize
the pthread_barrier, so this approach is not correct. The subsequent
patch will revert to using atomic_bool instead.
Link: https://lkml.kernel.org/r/20241018171734.2315053-1-edliaw@google.com
Link: https://lkml.kernel.org/r/20241018171734.2315053-2-edliaw@google.com
Fixes: e142cc87ac4e ("fix deadlock for fork after pthread_create on ARM")
Signed-off-by: Edward Liaw <edliaw@google.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Add a test to assert that VMG_FLAG_JUST_EXPAND functions as expected - that
is, when the VMA iterator is positioned at the previous VMA and no VMAs
proceed it, we observe an expansion with all state as expected.
Explicitly place a prior VMA that would otherwise fail this test if the
mode were not enabled (as it would traverse to the previous-previous VMA).
Link: https://lkml.kernel.org/r/d2f88330254a6448092412bf7dfe077a579ab0dc.1729174352.git.lorenzo.stoakes@oracle.com
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Jann Horn <jannh@google.com>
Cc: kernel test robot <oliver.sang@intel.com>
Cc: Liam R. Howlett <Liam.Howlett@Oracle.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Patch series "introduce VMA merge mode to improve brk() performance".
A ~5% performance regression was discovered on the
aim9.brk_test.ops_per_sec by the linux kernel test bot [0].
In the past to satisfy brk() performance we duplicated VMA expansion code
and special-cased do_brk_flags(). This is however horrid and undoes work
to abstract this logic, so in resolving the issue I have endeavoured to
avoid this.
Investigating further I was able to observe that the use of a
vma_iter_next_range() and vma_prev() pair, causing an unnecessary maple
tree walk. In addition there is work that we do that is simply
unnecessary for brk().
Therefore, add a special VMA merge mode VMG_FLAG_JUST_EXPAND to avoid
doing any of this - it assumes the VMA iterator is pointing at the
previous VMA and which skips logic that brk() does not require.
This mostly eliminates the performance regression reducing it to ~2% which
is in the realm of noise. In addition, the will-it-scale test brk2,
written to be more representative of real-world brk() usage, shows a
modest performance improvement - which gives me confidence that we are not
meaningfully regressing real workloads here.
This series includes a test asserting that the 'just expand' mode works as
expected.
With many thanks to Oliver Sang for helping with performance testing of
candidate patch sets!
[0]:https://lore.kernel.org/linux-mm/202409301043.629bea78-oliver.sang@intel.com
This patch (of 2):
We know in advance that do_brk_flags() wants only to perform a VMA
expansion (if the prior VMA is compatible), and that we assume no
mergeable VMA follows it.
These are the semantics of this function prior to the recent rewrite of
the VMA merging logic, however we are now doing more work than necessary -
positioning the VMA iterator at the prior VMA and performing tasks that
are not required.
Add a new field to the vmg struct to permit merge flags and add a new
merge flag VMG_FLAG_JUST_EXPAND which implies this behaviour, and have
do_brk_flags() use this.
This fixes a reported performance regression in a brk() benchmarking suite.
Link: https://lkml.kernel.org/r/cover.1729174352.git.lorenzo.stoakes@oracle.com
Link: https://lkml.kernel.org/r/4e65d4395e5841c5acf8470dbcb714016364fd39.1729174352.git.lorenzo.stoakes@oracle.com
Fixes: cacded5e42b9 ("mm: avoid using vma_merge() for new VMAs")
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/linux-mm/202409301043.629bea78-oliver.sang@intel.com
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@Oracle.com>
Cc: Jann Horn <jannh@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
walk_system_ram_res_rev() erroneously discards resource flags when passing
the information to the callback.
This causes systems with IORESOURCE_SYSRAM_DRIVER_MANAGED memory to have
these resources selected during kexec to store kexec buffers if that
memory happens to be at placed above normal system ram.
This leads to undefined behavior after reboot. If the kexec buffer is
never touched, nothing happens. If the kexec buffer is touched, it could
lead to a crash (like below) or undefined behavior.
Tested on a system with CXL memory expanders with driver managed memory,
TPM enabled, and CONFIG_IMA_KEXEC=y. Adding printk's showed the flags
were being discarded and as a result the check for
IORESOURCE_SYSRAM_DRIVER_MANAGED passes.
find_next_iomem_res: name(System RAM (kmem))
start(10000000000)
end(1034fffffff)
flags(83000200)
locate_mem_hole_top_down: start(10000000000) end(1034fffffff) flags(0)
[.] BUG: unable to handle page fault for address: ffff89834ffff000
[.] #PF: supervisor read access in kernel mode
[.] #PF: error_code(0x0000) - not-present page
[.] PGD c04c8bf067 P4D c04c8bf067 PUD c04c8be067 PMD 0
[.] Oops: 0000 [#1] SMP
[.] RIP: 0010:ima_restore_measurement_list+0x95/0x4b0
[.] RSP: 0018:ffffc900000d3a80 EFLAGS: 00010286
[.] RAX: 0000000000001000 RBX: 0000000000000000 RCX: ffff89834ffff000
[.] RDX: 0000000000000018 RSI: ffff89834ffff000 RDI: ffff89834ffff018
[.] RBP: ffffc900000d3ba0 R08: 0000000000000020 R09: ffff888132b8a900
[.] R10: 4000000000000000 R11: 000000003a616d69 R12: 0000000000000000
[.] R13: ffffffff8404ac28 R14: 0000000000000000 R15: ffff89834ffff000
[.] FS: 0000000000000000(0000) GS:ffff893d44640000(0000) knlGS:0000000000000000
[.] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[.] ata5: SATA link down (SStatus 0 SControl 300)
[.] CR2: ffff89834ffff000 CR3: 000001034d00f001 CR4: 0000000000770ef0
[.] PKRU: 55555554
[.] Call Trace:
[.] <TASK>
[.] ? __die+0x78/0xc0
[.] ? page_fault_oops+0x2a8/0x3a0
[.] ? exc_page_fault+0x84/0x130
[.] ? asm_exc_page_fault+0x22/0x30
[.] ? ima_restore_measurement_list+0x95/0x4b0
[.] ? template_desc_init_fields+0x317/0x410
[.] ? crypto_alloc_tfm_node+0x9c/0xc0
[.] ? init_ima_lsm+0x30/0x30
[.] ima_load_kexec_buffer+0x72/0xa0
[.] ima_init+0x44/0xa0
[.] __initstub__kmod_ima__373_1201_init_ima7+0x1e/0xb0
[.] ? init_ima_lsm+0x30/0x30
[.] do_one_initcall+0xad/0x200
[.] ? idr_alloc_cyclic+0xaa/0x110
[.] ? new_slab+0x12c/0x420
[.] ? new_slab+0x12c/0x420
[.] ? number+0x12a/0x430
[.] ? sysvec_apic_timer_interrupt+0xa/0x80
[.] ? asm_sysvec_apic_timer_interrupt+0x16/0x20
[.] ? parse_args+0xd4/0x380
[.] ? parse_args+0x14b/0x380
[.] kernel_init_freeable+0x1c1/0x2b0
[.] ? rest_init+0xb0/0xb0
[.] kernel_init+0x16/0x1a0
[.] ret_from_fork+0x2f/0x40
[.] ? rest_init+0xb0/0xb0
[.] ret_from_fork_asm+0x11/0x20
[.] </TASK>
Link: https://lore.kernel.org/all/20231114091658.228030-1-bhe@redhat.com/
Link: https://lkml.kernel.org/r/20241017190347.5578-1-gourry@gourry.net
Fixes: 7acf164b259d ("resource: add walk_system_ram_res_rev()")
Signed-off-by: Gregory Price <gourry@gourry.net>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Baoquan He <bhe@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: "Huang, Ying" <ying.huang@intel.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Syzbot reported that in directory operations after nilfs2 detects
filesystem corruption and degrades to read-only,
__block_write_begin_int(), which is called to prepare block writes, may
fail the BUG_ON check for accesses exceeding the folio/page size,
triggering a kernel bug.
This was found to be because the "checked" flag of a page/folio was not
cleared when it was discarded by nilfs2's own routine, which causes the
sanity check of directory entries to be skipped when the directory
page/folio is reloaded. So, fix that.
This was necessary when the use of nilfs2's own page discard routine was
applied to more than just metadata files.
Link: https://lkml.kernel.org/r/20241017193359.5051-1-konishi.ryusuke@gmail.com
Fixes: 8c26c4e2694a ("nilfs2: fix issue with flush kernel thread after remount in RO mode because of driver's internal error or metadata corruption")
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+d6ca2daf692c7a82f959@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=d6ca2daf692c7a82f959
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The acquired memory blocks for reserved may include blocks outside of
memory management. In this case, the nid variable is set to NUMA_NO_NODE
(-1), so an error occurs in node_set(). This adds a check using
numa_valid_node() to numa_clear_kernel_node_hotplug() that skips
node_set() when nid is set to NUMA_NO_NODE.
Link: https://lkml.kernel.org/r/1729070461-13576-1-git-send-email-nobuhiro1.iwamatsu@toshiba.co.jp
Fixes: 87482708210f ("mm: introduce numa_memblks")
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Suggested-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Syzbot reported a kernel BUG in ocfs2_truncate_inline. There are two
reasons for this: first, the parameter value passed is greater than
ocfs2_max_inline_data_with_xattr, second, the start and end parameters of
ocfs2_truncate_inline are "unsigned int".
So, we need to add a sanity check for byte_start and byte_len right before
ocfs2_truncate_inline() in ocfs2_remove_inode_range(), if they are greater
than ocfs2_max_inline_data_with_xattr return -EINVAL.
Link: https://lkml.kernel.org/r/tencent_D48DB5122ADDAEDDD11918CFB68D93258C07@qq.com
Fixes: 1afc32b95233 ("ocfs2: Write support for inline data")
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Reported-by: syzbot+81092778aac03460d6b7@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=81092778aac03460d6b7
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
I got the following KCSAN report during syzbot testing:
==================================================================
BUG: KCSAN: data-race in generic_fillattr / inode_set_ctime_current
write to 0xffff888102eb3260 of 4 bytes by task 6565 on cpu 1:
inode_set_ctime_to_ts include/linux/fs.h:1638 [inline]
inode_set_ctime_current+0x169/0x1d0 fs/inode.c:2626
shmem_mknod+0x117/0x180 mm/shmem.c:3443
shmem_create+0x34/0x40 mm/shmem.c:3497
lookup_open fs/namei.c:3578 [inline]
open_last_lookups fs/namei.c:3647 [inline]
path_openat+0xdbc/0x1f00 fs/namei.c:3883
do_filp_open+0xf7/0x200 fs/namei.c:3913
do_sys_openat2+0xab/0x120 fs/open.c:1416
do_sys_open fs/open.c:1431 [inline]
__do_sys_openat fs/open.c:1447 [inline]
__se_sys_openat fs/open.c:1442 [inline]
__x64_sys_openat+0xf3/0x120 fs/open.c:1442
x64_sys_call+0x1025/0x2d60 arch/x86/include/generated/asm/syscalls_64.h:258
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0x54/0x120 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x76/0x7e
read to 0xffff888102eb3260 of 4 bytes by task 3498 on cpu 0:
inode_get_ctime_nsec include/linux/fs.h:1623 [inline]
inode_get_ctime include/linux/fs.h:1629 [inline]
generic_fillattr+0x1dd/0x2f0 fs/stat.c:62
shmem_getattr+0x17b/0x200 mm/shmem.c:1157
vfs_getattr_nosec fs/stat.c:166 [inline]
vfs_getattr+0x19b/0x1e0 fs/stat.c:207
vfs_statx_path fs/stat.c:251 [inline]
vfs_statx+0x134/0x2f0 fs/stat.c:315
vfs_fstatat+0xec/0x110 fs/stat.c:341
__do_sys_newfstatat fs/stat.c:505 [inline]
__se_sys_newfstatat+0x58/0x260 fs/stat.c:499
__x64_sys_newfstatat+0x55/0x70 fs/stat.c:499
x64_sys_call+0x141f/0x2d60 arch/x86/include/generated/asm/syscalls_64.h:263
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0x54/0x120 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x76/0x7e
value changed: 0x2755ae53 -> 0x27ee44d3
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 UID: 0 PID: 3498 Comm: udevd Not tainted 6.11.0-rc6-syzkaller-00326-gd1f2d51b711a-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/06/2024
==================================================================
When calling generic_fillattr(), if you don't hold read lock, data-race
will occur in inode member variables, which can cause unexpected
behavior.
Since there is no special protection when shmem_getattr() calls
generic_fillattr(), data-race occurs by functions such as shmem_unlink()
or shmem_mknod(). This can cause unexpected results, so commenting it out
is not enough.
Therefore, when calling generic_fillattr() from shmem_getattr(), it is
appropriate to protect the inode using inode_lock_shared() and
inode_unlock_shared() to prevent data-race.
Link: https://lkml.kernel.org/r/20240909123558.70229-1-aha310510@gmail.com
Fixes: 44a30220bc0a ("shmem: recalculate file inode when fstat")
Signed-off-by: Jeongjun Park <aha310510@gmail.com>
Reported-by: syzbot <syzkaller@googlegroup.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Yu Zhao <yuzhao@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
vms_abort_munmap_vmas() is a recovery path where, on entry, some VMAs have
already been torn down halfway (in a way we can't undo) but are still
present in the maple tree.
At this point, we *must* remove the VMAs from the VMA tree, otherwise we
get UAF.
Because removing VMA tree nodes can require memory allocation, the
existing code has an error path which tries to handle this by reattaching
the VMAs; but that can't be done safely.
A nicer way to fix it would probably be to preallocate enough maple tree
nodes for the removal before the point of no return, or something like
that; but for now, fix it the easy and kinda ugly way, by marking this
allocation __GFP_NOFAIL.
Link: https://lkml.kernel.org/r/20241016-fix-munmap-abort-v1-1-601c94b2240d@google.com
Fixes: 4f87153e82c4 ("mm: change failure of MAP_FIXED to restoring the gap on failure")
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@Oracle.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
During x86_64 kernel build with CONFIG_KMSAN, the objtool warns following:
AR built-in.a
AR vmlinux.a
LD vmlinux.o
vmlinux.o: warning: objtool: handle_bug+0x4: call to
kmsan_unpoison_entry_regs() leaves .noinstr.text section
OBJCOPY modules.builtin.modinfo
GEN modules.builtin
MODPOST Module.symvers
CC .vmlinux.export.o
Moving kmsan_unpoison_entry_regs() _after_ instrumentation_begin() fixes
the warning.
There is decode_bug(regs->ip, &imm) is left before KMSAN unpoisoining, but
it has the return condition and if we include it after
instrumentation_begin() it results the warning "return with
instrumentation enabled", hence, I'm concerned that regs will not be KMSAN
unpoisoned if `ud_type == BUG_NONE` is true.
Link: https://lkml.kernel.org/r/20241016152407.3149001-1-snovitoll@gmail.com
Fixes: ba54d194f8da ("x86/traps: avoid KMSAN bugs originating from handle_bug()")
Signed-off-by: Sabyrzhan Tasbolatov <snovitoll@gmail.com>
Reviewed-by: Alexander Potapenko <glider@google.com>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
We want to use the functions (get_free_mem_region()) configured via
GET_FREE_REGION in resource kunit tests. However, GET_FREE_REGION
depends on SPARSEMEM now. This makes resource kunit tests cannot be
built on some architectures lacking SPARSEMEM, or causes config warning
as follows,
WARNING: unmet direct dependencies detected for GET_FREE_REGION
Depends on [n]: SPARSEMEM [=n]
Selected by [y]:
- RESOURCE_KUNIT_TEST [=y] && RUNTIME_TESTING_MENU [=y] && KUNIT [=y]
When get_free_mem_region() was introduced the only consumers were those
looking to pass the address range to memremap_pages(). That address
range needed to be mindful of the maximum addressable platform physical
address which at the time only SPARSMEM defined via MAX_PHYSMEM_BITS.
Given that memremap_pages() also depended on SPARSEMEM via ZONE_DEVICE,
it was easier to just depend on that definition than invent a general
MAX_PHYSMEM_BITS concept outside of SPARSEMEM.
Turns out that decision was buggy and did not account for KASAN
consumption of physical address space. That problem was resolved
recently with commit ea72ce5da228 ("x86/kaslr: Expose and use the end
of the physical memory address space"), and GET_FREE_REGION dropped its
MAX_PHYSMEM_BITS dependency.
Then commit 99185c10d5d9 ("resource, kunit: add test case for
region_intersects()"), went ahead and fixed up the only remaining
dependency on SPARSEMEM which was usage of the PA_SECTION_SHIFT macro
for setting the default alignment. A PAGE_SIZE fallback is fine in the
SPARSEMEM=n case.
With those build dependencies gone GET_FREE_REGION no longer depends on
SPARSEMEM. So, the patch removes dependency on SPARSEMEM from
GET_FREE_REGION to fix the build issues.
Link: https://lkml.kernel.org/r/20241016014730.339369-1-ying.huang@intel.com
Link: https://lore.kernel.org/lkml/20240922225041.603186-1-linux@roeck-us.net/
Link: https://lkml.kernel.org/r/20241015051554.294734-1-ying.huang@intel.com
Fixes: 99185c10d5d9 ("resource, kunit: add test case for region_intersects()")
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Co-developed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: David Hildenbrand <david@redhat.com>
Tested-by: Nathan Chancellor <nathan@kernel.org> # build
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jonathan Cameron <jonathan.cameron@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Avoiding the zeroing of the vma tree in mmap_region() introduced a race
with truncate in the page table walk. To avoid any races, create a hole
in the rmap during the operation by clearing the pagetable entries earlier
under the mmap write lock and (critically) before the new vma is installed
into the vma tree. The result is that the old vma(s) are left in the vma
tree, but free_pgtables() removes them from the rmap and clears the ptes
while holding the necessary locks.
This change extends the fix required for hugetblfs and the call_mmap()
function by moving the cleanup higher in the function and running it
unconditionally.
Link: https://lkml.kernel.org/r/20241016013455.2241533-1-Liam.Howlett@oracle.com
Fixes: f8d112a4e657 ("mm/mmap: avoid zeroing vma tree in mmap_region()")
Signed-off-by: Liam R. Howlett <Liam.Howlett@Oracle.com>
Reported-by: Jann Horn <jannh@google.com>
Closes: https://lore.kernel.org/all/CAG48ez0ZpGzxi=-5O_uGQ0xKXOmbjeQ0LjZsRJ1Qtf2X5eOr1w@mail.gmail.com/
Reviewed-by: Jann Horn <jannh@google.com>
Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Under memory pressure it's possible for GFP_ATOMIC order-0 allocations to
fail even though free pages are available in the highatomic reserves.
GFP_ATOMIC allocations cannot trigger unreserve_highatomic_pageblock()
since it's only run from reclaim.
Given that such allocations will pass the watermarks in
__zone_watermark_unusable_free(), it makes sense to fallback to highatomic
reserves the same way that ALLOC_OOM can.
This fixes order-0 page allocation failures observed on Cloudflare's fleet
when handling network packets:
kswapd1: page allocation failure: order:0, mode:0x820(GFP_ATOMIC),
nodemask=(null),cpuset=/,mems_allowed=0-7
CPU: 10 PID: 696 Comm: kswapd1 Kdump: loaded Tainted: G O 6.6.43-CUSTOM #1
Hardware name: MACHINE
Call Trace:
<IRQ>
dump_stack_lvl+0x3c/0x50
warn_alloc+0x13a/0x1c0
__alloc_pages_slowpath.constprop.0+0xc9d/0xd10
__alloc_pages+0x327/0x340
__napi_alloc_skb+0x16d/0x1f0
bnxt_rx_page_skb+0x96/0x1b0 [bnxt_en]
bnxt_rx_pkt+0x201/0x15e0 [bnxt_en]
__bnxt_poll_work+0x156/0x2b0 [bnxt_en]
bnxt_poll+0xd9/0x1c0 [bnxt_en]
__napi_poll+0x2b/0x1b0
bpf_trampoline_6442524138+0x7d/0x1000
__napi_poll+0x5/0x1b0
net_rx_action+0x342/0x740
handle_softirqs+0xcf/0x2b0
irq_exit_rcu+0x6c/0x90
sysvec_apic_timer_interrupt+0x72/0x90
</IRQ>
[mfleming@cloudflare.com: update comment]
Link: https://lkml.kernel.org/r/20241015125158.3597702-1-matt@readmodwrite.com
Link: https://lkml.kernel.org/r/20241011120737.3300370-1-matt@readmodwrite.com
Link: https://lore.kernel.org/all/CAGis_TWzSu=P7QJmjD58WWiu3zjMTVKSzdOwWE8ORaGytzWJwQ@mail.gmail.com/
Fixes: 1d91df85f399 ("mm/page_alloc: handle a missing case for memalloc_nocma_{save/restore} APIs")
Signed-off-by: Matt Fleming <mfleming@cloudflare.com>
Suggested-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
There is no reason to invoke these hooks early against an mm that is in an
incomplete state.
The change in commit d24062914837 ("fork: use __mt_dup() to duplicate
maple tree in dup_mmap()") makes this more pertinent as we may be in a
state where entries in the maple tree are not yet consistent.
Their placement early in dup_mmap() only appears to have been meaningful
for early error checking, and since functionally it'd require a very small
allocation to fail (in practice 'too small to fail') that'd only occur in
the most dire circumstances, meaning the fork would fail or be OOM'd in
any case.
Since both khugepaged and KSM tracking are there to provide optimisations
to memory performance rather than critical functionality, it doesn't
really matter all that much if, under such dire memory pressure, we fail
to register an mm with these.
As a result, we follow the example of commit d2081b2bf819 ("mm:
khugepaged: make khugepaged_enter() void function") and make ksm_fork() a
void function also.
We only expose the mm to these functions once we are done with them and
only if no error occurred in the fork operation.
Link: https://lkml.kernel.org/r/e0cb8b840c9d1d5a6e84d4f8eff5f3f2022aa10c.1729014377.git.lorenzo.stoakes@oracle.com
Fixes: d24062914837 ("fork: use __mt_dup() to duplicate maple tree in dup_mmap()")
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reported-by: Jann Horn <jannh@google.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@Oracle.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Jann Horn <jannh@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Patch series "fork: do not expose incomplete mm on fork".
During fork we may place the virtual memory address space into an
inconsistent state before the fork operation is complete.
In addition, we may encounter an error during the fork operation that
indicates that the virtual memory address space is invalidated.
As a result, we should not be exposing it in any way to external machinery
that might interact with the mm or VMAs, machinery that is not designed to
deal with incomplete state.
We specifically update the fork logic to defer khugepaged and ksm to the
end of the operation and only to be invoked if no error arose, and
disallow uffd from observing fork events should an error have occurred.
This patch (of 2):
Currently on fork we expose the virtual address space of a process to
userland unconditionally if uffd is registered in VMAs, regardless of
whether an error arose in the fork.
This is performed in dup_userfaultfd_complete() which is invoked
unconditionally, and performs two duties - invoking registered handlers
for the UFFD_EVENT_FORK event via dup_fctx(), and clearing down
userfaultfd_fork_ctx objects established in dup_userfaultfd().
This is problematic, because the virtual address space may not yet be
correctly initialised if an error arose.
The change in commit d24062914837 ("fork: use __mt_dup() to duplicate
maple tree in dup_mmap()") makes this more pertinent as we may be in a
state where entries in the maple tree are not yet consistent.
We address this by, on fork error, ensuring that we roll back state that
we would otherwise expect to clean up through the event being handled by
userland and perform the memory freeing duty otherwise performed by
dup_userfaultfd_complete().
We do this by implementing a new function, dup_userfaultfd_fail(), which
performs the same loop, only decrementing reference counts.
Note that we perform mmgrab() on the parent and child mm's, however
userfaultfd_ctx_put() will mmdrop() this once the reference count drops to
zero, so we will avoid memory leaks correctly here.
Link: https://lkml.kernel.org/r/cover.1729014377.git.lorenzo.stoakes@oracle.com
Link: https://lkml.kernel.org/r/d3691d58bb58712b6fb3df2be441d175bd3cdf07.1729014377.git.lorenzo.stoakes@oracle.com
Fixes: d24062914837 ("fork: use __mt_dup() to duplicate maple tree in dup_mmap()")
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reported-by: Jann Horn <jannh@google.com>
Reviewed-by: Jann Horn <jannh@google.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@Oracle.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
pmd_leaf()/pud_leaf() only implies a pmd_present()/pud_present() check on
some architectures. We really should check for
pmd_present()/pud_present() first.
This should explain the report we got on ppc64 (which has
CONFIG_PGTABLE_HAS_HUGE_LEAVES set in the config) that triggered:
VM_WARN_ON_ONCE(pmd_leaf(pmdp_get_lockless(pmdp)));
Likely we had a PMD migration entry for which pmd_leaf() did not trigger.
We raced with restoring the PMD migration entry, and suddenly saw a
pmd_leaf(). In this case, pte_offset_map_lock() saved us from more
trouble, because it rechecks the PMD value, but we would not have
processed the migration entry -- which is not too bad because the only
user of FW_MIGRATION is KSM for unsharing, and KSM only applies to small
folios.
Further, we shouldn't re-read the PMD/PUD value for our warning, the
primary purpose of the VM_WARN_ON_ONCE() is to find spurious use of
pmd_leaf()/pud_leaf() without CONFIG_PGTABLE_HAS_HUGE_LEAVES.
As a side note, we are currently not implementing FW_MIGRATION support for
PUD migration entries, which likely should exist due to hugetlb. Add a
TODO so this won't fall through the cracks if more FW_MIGRATION users get
added.
Was able to write a quick reproducer and verify that the issue no longer triggers with this fix.
https://gitlab.com/davidhildenbrand/scratchspace/-/blob/main/reproducers/move-pages-pmd-leaf.c
Without this fix after a couple of seconds in a VM with 2 NUMA nodes:
[ 54.333753] ------------[ cut here ]------------
[ 54.334901] WARNING: CPU: 20 PID: 1704 at mm/pagewalk.c:815 folio_walk_start+0x48f/0x6e0
[ 54.336455] Modules linked in: ...
[ 54.345009] CPU: 20 UID: 0 PID: 1704 Comm: move-pages-pmd- Not tainted 6.12.0-rc2+ #81
[ 54.346529] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-2.fc40 04/01/2014
[ 54.348191] RIP: 0010:folio_walk_start+0x48f/0x6e0
[ 54.349134] Code: b5 ad 48 8d 35 00 00 00 00 e8 6d 59 d7 ff e8 08 74 da ff e9 9c fe ff ff 4c 8b 7c 24 08 4c 89 ff e8 26 2b be 00 e9 8a fe ff ff <0f> 0b e9 ec fe ff ff f7 c2 ff 0f 00 00 0f 85 81 fe ff ff 48 8b 02
[ 54.352660] RSP: 0018:ffffb7e4c430bc78 EFLAGS: 00010282
[ 54.353679] RAX: 80000002a3e008e7 RBX: ffff9946039aa580 RCX: ffff994380000000
[ 54.355056] RDX: ffff994606aec000 RSI: 00007f004b000000 RDI: 0000000000000000
[ 54.356440] RBP: 00007f004b000000 R08: 0000000000000591 R09: 0000000000000001
[ 54.357820] R10: 0000000000000200 R11: 0000000000000001 R12: ffffb7e4c430bd10
[ 54.359198] R13: ffff994606aec2c0 R14: 0000000000000002 R15: ffff994604a89b00
[ 54.360564] FS: 00007f004ae006c0(0000) GS:ffff9947f7400000(0000) knlGS:0000000000000000
[ 54.362111] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 54.363242] CR2: 00007f004adffe58 CR3: 0000000281e12005 CR4: 0000000000770ef0
[ 54.364615] PKRU: 55555554
[ 54.365153] Call Trace:
[ 54.365646] <TASK>
[ 54.366073] ? __warn.cold+0xb7/0x14d
[ 54.366796] ? folio_walk_start+0x48f/0x6e0
[ 54.367628] ? report_bug+0xff/0x140
[ 54.368324] ? handle_bug+0x58/0x90
[ 54.369019] ? exc_invalid_op+0x17/0x70
[ 54.369771] ? asm_exc_invalid_op+0x1a/0x20
[ 54.370606] ? folio_walk_start+0x48f/0x6e0
[ 54.371415] ? folio_walk_start+0x9e/0x6e0
[ 54.372227] do_pages_move+0x1c5/0x680
[ 54.372972] kernel_move_pages+0x1a1/0x2b0
[ 54.373804] __x64_sys_move_pages+0x25/0x30
Link: https://lkml.kernel.org/r/20241015111236.1290921-1-david@redhat.com
Fixes: aa39ca6940f1 ("mm/pagewalk: introduce folio_walk_start() + folio_walk_end()")
Signed-off-by: David Hildenbrand <david@redhat.com>
Reported-by: syzbot+7d917f67c05066cec295@syzkaller.appspotmail.com
Closes: https://lkml.kernel.org/r/670d3248.050a0220.3e960.0064.GAE@google.com
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Qi Zheng <zhengqi.arch@bytedance.com>
Cc: Jann Horn <jannh@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The widgets array in the snd_soc_dapm_widget_list has a __counted_by
attribute attached to it, which points to the num_widgets variable. This
attribute is used in bounds checking, and if it is not set before the
array is filled, then the bounds sanitizer will issue a warning or a
kernel panic if CONFIG_UBSAN_TRAP is set.
This patch sets the size of the widgets list calculated with
list_for_each as the initial value for num_widgets as it is used for
allocating memory for the array. It is updated with the actual number of
added elements after the array is filled.
Signed-off-by: Aleksei Vetrov <vvvvvv@google.com>
Fixes: 80e698e2df5b ("ASoC: soc-dapm: Annotate struct snd_soc_dapm_widget_list with __counted_by")
Link: https://patch.msgid.link/20241028-soc-dapm-bounds-checker-fix-v1-1-262b0394e89e@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move the allocation of chip->auth to tpm2_start_auth_session() so that this
field can be used as flag to tell whether auth session is active or not.
Instead of flushing and reloading the auth session for every transaction
separately, keep the session open unless /dev/tpm0 is used.
Reported-by: Pengyu Ma <mapengyu@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219229
Cc: stable@vger.kernel.org # v6.10+
Fixes: 7ca110f2679b ("tpm: Address !chip->auth in tpm_buf_append_hmac_session*()")
Tested-by: Pengyu Ma <mapengyu@gmail.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
Fix the new "LPE0F28" code path using the uninitialized ctx variable
to log an error.
Fixes: 6668610b4d8c ("ASoC: Intel: sst: Support LPE0F28 ACPI HID")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202410261106.EBx49ssy-lkp@intel.com/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241026143615.171821-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
As there are duplicated kernel headers in tools/include libc can pick
up the wrong definitions. This was causing the wrong system call for
capget in perf.
Reported-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: e25ebda78e230283 ("perf cap: Tidy up and improve capability testing")
Closes: https://lore.kernel.org/lkml/cc7d6bdf-1aeb-4179-9029-4baf50b59342@intel.com/
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20241026055448.312247-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
To pick up the changes in:
7f053812dab3946c ("random: vDSO: minimize and simplify header includes")
That required adding a copy of include/vdso/unaligned.h and its checking
in tools/perf/check-headers.h.
Addressing this perf tools build warning:
Warning: Kernel ABI header differences:
diff -u tools/include/linux/unaligned.h include/linux/unaligned.h
Please see tools/include/uapi/README for further details.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Ian Rogers <irogers@google.com>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/lkml/Zx-uHvAbPAESofEN@x1
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
To get the changes in:
924725707d80bc25 ("arm64: cputype: Add Neoverse-N3 definitions")
That makes this perf source code to be rebuilt:
CC /tmp/build/perf-tools/util/arm-spe.o
The changes in the above patch add MIDR_NEOVERSE_N3, that probably need
changes in arm-spe.c, so probably we need to add it to that array? Or
maybe we need to leave this for later when this is all tested on those
machines?
static const struct midr_range neoverse_spe[] = {
MIDR_ALL_VERSIONS(MIDR_NEOVERSE_N1),
MIDR_ALL_VERSIONS(MIDR_NEOVERSE_N2),
MIDR_ALL_VERSIONS(MIDR_NEOVERSE_V1),
{},
};
Mark Rutland recommended about arm-spe.c in a previous update to this
file:
"I would not touch this for now -- someone would have to go audit the
TRMs to check that those other cores have the same encoding, and I think
it'd be better to do that as a follow-up."
That addresses this perf build warning:
Warning: Kernel ABI header differences:
diff -u tools/arch/arm64/include/asm/cputype.h arch/arm64/include/asm/cputype.h
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/lkml/Zx-dffKdGsgkhG96@x1
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
To pick up the changes in this cset:
947697c6f0f75f98 ("uapi: Define GENMASK_U128")
This addresses these perf build warnings:
Warning: Kernel ABI header differences:
diff -u tools/include/uapi/linux/bits.h include/uapi/linux/bits.h
diff -u tools/include/linux/bits.h include/linux/bits.h
Please see tools/include/uapi/README for further details.
Acked-by: Yury Norov <yury.norov@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/lkml/Zx-ZVH7bHqtFn8Dv@x1
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Do not continue on tpm2_create_primary() failure in tpm2_load_null().
Cc: stable@vger.kernel.org # v6.10+
Fixes: eb24c9788cd9 ("tpm: disable the TPM if NULL name changes")
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
Do not continue tpm2_sessions_init() further if the null key pair creation
fails.
Cc: stable@vger.kernel.org # v6.10+
Fixes: d2add27cf2b8 ("tpm: Add NULL primary creation")
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
If devm_gpiod_get_optional() fails, we need to disable previously enabled
regulators, as done in the other error handling path of the function.
Also, gpiod_set_value_cansleep(, 1) needs to be called to undo a
potential gpiod_set_value_cansleep(, 0).
If the "reset" gpio is not defined, this additional call is just a no-op.
This behavior is the same as the one already in the .remove() function.
Fixes: 11b9cd748e31 ("ASoC: cs42l51: add reset management")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/a5e5f4b9fb03f46abd2c93ed94b5c395972ce0d1.1729975570.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
In a commit 24b7f8e5cd65 ("firewire: core: use helper functions for self
ID sequence"), the enumeration over self ID sequence was refactored with
some helper functions with KUnit tests. These helper functions are
guaranteed to work expectedly by the KUnit tests, however their application
includes a mistake to assign invalid value to the index of port connected
to parent device.
This bug affects the case that any extra node devices which has three or
more ports are connected to 1394 OHCI controller. In the case, the path
to update the tree cache could hits WARN_ON(), and gets general protection
fault due to the access to invalid address computed by the invalid value.
This commit fixes the bug to assign correct port index.
Cc: stable@vger.kernel.org
Reported-by: Edmund Raile <edmund.raile@proton.me>
Closes: https://lore.kernel.org/lkml/8a9902a4ece9329af1e1e42f5fea76861f0bf0e8.camel@proton.me/
Fixes: 24b7f8e5cd65 ("firewire: core: use helper functions for self ID sequence")
Link: https://lore.kernel.org/r/20241025034137.99317-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
|
|
When support for vivobook fan profiles was added, the initial
call to throttle_thermal_policy_set_default() was removed, which
however is necessary for full initialization.
Fix this by calling throttle_thermal_policy_set_default() again
when setting up the platform profile.
Fixes: bcbfcebda2cb ("platform/x86: asus-wmi: add support for vivobook fan profiles")
Reported-by: Michael Larabel <Michael@phoronix.com>
Closes: https://www.phoronix.com/review/lunar-lake-xe2/5
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20241025191514.15032-2-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
cc9877fb7677 ("sched_ext: Improve error reporting during loading") changed
how load failures are reported so that more error context can be
communicated. This breaks the enq_last_no_enq_fails test as attach no longer
fails. The scheduler is guaranteed to be ejected on attach completion with
full error information. Update enq_last_no_enq_fails so that it checks that
the scheduler is ejected using ops.exit().
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Vishal Chourasia <vishalc@linux.ibm.com>
Link: http://lkml.kernel.org/r/Zxknp7RAVNjmdJSc@linux.ibm.com
Fixes: cc9877fb7677 ("sched_ext: Improve error reporting during loading")
|
|
cast_mask() doesn't do any actual work and is defined in a header file.
Force it to be inline. When it is not inlined and the function is not used,
it can cause verificaiton failures like the following:
# tools/testing/selftests/sched_ext/runner -t minimal
===== START =====
TEST: minimal
DESCRIPTION: Verify we can load a fully minimal scheduler
OUTPUT:
libbpf: prog 'cast_mask': missing BPF prog type, check ELF section name '.text'
libbpf: prog 'cast_mask': failed to load: -22
libbpf: failed to load object 'minimal'
libbpf: failed to load BPF skeleton 'minimal': -22
ERR: minimal.c:20
Failed to open and load skel
not ok 1 minimal #
===== END =====
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: a748db0c8c6a ("tools/sched_ext: Receive misc updates from SCX repo")
|
|
scx_ops_bypass() can currently race on the ops enable / disable path as
follows:
1. scx_ops_bypass(true) called on enable path, bypass depth is set to 1
2. An op on the init path exits, which schedules scx_ops_disable_workfn()
3. scx_ops_bypass(false) is called on the disable path, and bypass depth
is decremented to 0
4. kthread is scheduled to execute scx_ops_disable_workfn()
5. scx_ops_bypass(true) called, bypass depth set to 1
6. scx_ops_bypass() races when iterating over CPUs
While it's not safe to take any blocking locks on the bypass path, it is
safe to take a raw spinlock which cannot be preempted. This patch therefore
updates scx_ops_bypass() to use a raw spinlock to synchronize, and changes
scx_ops_bypass_depth to be a regular int.
Without this change, we observe the following warnings when running the
'exit' sched_ext selftest (sometimes requires a couple of runs):
.[root@virtme-ng sched_ext]# ./runner -t exit
===== START =====
TEST: exit
...
[ 14.935078] WARNING: CPU: 2 PID: 360 at kernel/sched/ext.c:4332 scx_ops_bypass+0x1ca/0x280
[ 14.935126] Modules linked in:
[ 14.935150] CPU: 2 UID: 0 PID: 360 Comm: sched_ext_ops_h Not tainted 6.11.0-virtme #24
[ 14.935192] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.16.3-1-1 04/01/2014
[ 14.935242] Sched_ext: exit (enabling+all)
[ 14.935244] RIP: 0010:scx_ops_bypass+0x1ca/0x280
[ 14.935300] Code: ff ff ff e8 48 96 10 00 fb e9 08 ff ff ff c6 05 7b 34 e8 01 01 90 48 c7 c7 89 86 88 87 e8 be 1d f8 ff 90 0f 0b 90 90 eb 95 90 <0f> 0b 90 41 8b 84 24 24 0a 00 00 eb 97 90 0f 0b 90 41 8b 84 24 24
[ 14.935394] RSP: 0018:ffffb706c0957ce0 EFLAGS: 00010002
[ 14.935424] RAX: 0000000000000009 RBX: 0000000000000001 RCX: 00000000e3fb8b2a
[ 14.935465] RDX: 0000000000000001 RSI: 0000000000000004 RDI: ffffffff88a4c080
[ 14.935512] RBP: 0000000000009b56 R08: 0000000000000004 R09: 00000003f12e520a
[ 14.935555] R10: ffffffff863a9795 R11: 0000000000000000 R12: ffff8fc5fec31300
[ 14.935598] R13: ffff8fc5fec31318 R14: 0000000000000286 R15: 0000000000000018
[ 14.935642] FS: 0000000000000000(0000) GS:ffff8fc5fe680000(0000) knlGS:0000000000000000
[ 14.935684] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 14.935721] CR2: 0000557d92890b88 CR3: 000000002464a000 CR4: 0000000000750ef0
[ 14.935765] PKRU: 55555554
[ 14.935782] Call Trace:
[ 14.935802] <TASK>
[ 14.935823] ? __warn+0xce/0x220
[ 14.935850] ? scx_ops_bypass+0x1ca/0x280
[ 14.935881] ? report_bug+0xc1/0x160
[ 14.935909] ? handle_bug+0x61/0x90
[ 14.935934] ? exc_invalid_op+0x1a/0x50
[ 14.935959] ? asm_exc_invalid_op+0x1a/0x20
[ 14.935984] ? raw_spin_rq_lock_nested+0x15/0x30
[ 14.936019] ? scx_ops_bypass+0x1ca/0x280
[ 14.936046] ? srso_alias_return_thunk+0x5/0xfbef5
[ 14.936081] ? __pfx_scx_ops_disable_workfn+0x10/0x10
[ 14.936111] scx_ops_disable_workfn+0x146/0xac0
[ 14.936142] ? finish_task_switch+0xa9/0x2c0
[ 14.936172] ? srso_alias_return_thunk+0x5/0xfbef5
[ 14.936211] ? __pfx_scx_ops_disable_workfn+0x10/0x10
[ 14.936244] kthread_worker_fn+0x101/0x2c0
[ 14.936268] ? __pfx_kthread_worker_fn+0x10/0x10
[ 14.936299] kthread+0xec/0x110
[ 14.936327] ? __pfx_kthread+0x10/0x10
[ 14.936351] ret_from_fork+0x37/0x50
[ 14.936374] ? __pfx_kthread+0x10/0x10
[ 14.936400] ret_from_fork_asm+0x1a/0x30
[ 14.936427] </TASK>
[ 14.936443] irq event stamp: 21002
[ 14.936467] hardirqs last enabled at (21001): [<ffffffff863aa35f>] resched_cpu+0x9f/0xd0
[ 14.936521] hardirqs last disabled at (21002): [<ffffffff863dd0ba>] scx_ops_bypass+0x11a/0x280
[ 14.936571] softirqs last enabled at (20642): [<ffffffff863683d7>] __irq_exit_rcu+0x67/0xd0
[ 14.936622] softirqs last disabled at (20637): [<ffffffff863683d7>] __irq_exit_rcu+0x67/0xd0
[ 14.936672] ---[ end trace 0000000000000000 ]---
[ 14.953282] sched_ext: BPF scheduler "exit" disabled (unregistered from BPF)
[ 14.953352] ------------[ cut here ]------------
[ 14.953383] WARNING: CPU: 2 PID: 360 at kernel/sched/ext.c:4335 scx_ops_bypass+0x1d8/0x280
[ 14.953428] Modules linked in:
[ 14.953453] CPU: 2 UID: 0 PID: 360 Comm: sched_ext_ops_h Tainted: G W 6.11.0-virtme #24
[ 14.953505] Tainted: [W]=WARN
[ 14.953527] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.16.3-1-1 04/01/2014
[ 14.953574] RIP: 0010:scx_ops_bypass+0x1d8/0x280
[ 14.953603] Code: c6 05 7b 34 e8 01 01 90 48 c7 c7 89 86 88 87 e8 be 1d f8 ff 90 0f 0b 90 90 eb 95 90 0f 0b 90 41 8b 84 24 24 0a 00 00 eb 97 90 <0f> 0b 90 41 8b 84 24 24 0a 00 00 eb 92 f3 0f 1e fa 49 8d 84 24 f0
[ 14.953693] RSP: 0018:ffffb706c0957ce0 EFLAGS: 00010046
[ 14.953722] RAX: 0000000000000001 RBX: 0000000000000000 RCX: 0000000000000001
[ 14.953763] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff8fc5fec31318
[ 14.953804] RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000000
[ 14.953845] R10: ffffffff863a9795 R11: 0000000000000000 R12: ffff8fc5fec31300
[ 14.953888] R13: ffff8fc5fec31318 R14: 0000000000000286 R15: 0000000000000018
[ 14.953934] FS: 0000000000000000(0000) GS:ffff8fc5fe680000(0000) knlGS:0000000000000000
[ 14.953974] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 14.954009] CR2: 0000557d92890b88 CR3: 000000002464a000 CR4: 0000000000750ef0
[ 14.954052] PKRU: 55555554
[ 14.954068] Call Trace:
[ 14.954085] <TASK>
[ 14.954102] ? __warn+0xce/0x220
[ 14.954126] ? scx_ops_bypass+0x1d8/0x280
[ 14.954150] ? report_bug+0xc1/0x160
[ 14.954178] ? handle_bug+0x61/0x90
[ 14.954203] ? exc_invalid_op+0x1a/0x50
[ 14.954226] ? asm_exc_invalid_op+0x1a/0x20
[ 14.954250] ? raw_spin_rq_lock_nested+0x15/0x30
[ 14.954285] ? scx_ops_bypass+0x1d8/0x280
[ 14.954311] ? __mutex_unlock_slowpath+0x3a/0x260
[ 14.954343] scx_ops_disable_workfn+0xa3e/0xac0
[ 14.954381] ? __pfx_scx_ops_disable_workfn+0x10/0x10
[ 14.954413] kthread_worker_fn+0x101/0x2c0
[ 14.954442] ? __pfx_kthread_worker_fn+0x10/0x10
[ 14.954479] kthread+0xec/0x110
[ 14.954507] ? __pfx_kthread+0x10/0x10
[ 14.954530] ret_from_fork+0x37/0x50
[ 14.954553] ? __pfx_kthread+0x10/0x10
[ 14.954576] ret_from_fork_asm+0x1a/0x30
[ 14.954603] </TASK>
[ 14.954621] irq event stamp: 21002
[ 14.954644] hardirqs last enabled at (21001): [<ffffffff863aa35f>] resched_cpu+0x9f/0xd0
[ 14.954686] hardirqs last disabled at (21002): [<ffffffff863dd0ba>] scx_ops_bypass+0x11a/0x280
[ 14.954735] softirqs last enabled at (20642): [<ffffffff863683d7>] __irq_exit_rcu+0x67/0xd0
[ 14.954782] softirqs last disabled at (20637): [<ffffffff863683d7>] __irq_exit_rcu+0x67/0xd0
[ 14.954829] ---[ end trace 0000000000000000 ]---
[ 15.022283] sched_ext: BPF scheduler "exit" disabled (unregistered from BPF)
[ 15.092282] sched_ext: BPF scheduler "exit" disabled (unregistered from BPF)
[ 15.149282] sched_ext: BPF scheduler "exit" disabled (unregistered from BPF)
ok 1 exit #
===== END =====
And with it, the test passes without issue after 1000s of runs:
.[root@virtme-ng sched_ext]# ./runner -t exit
===== START =====
TEST: exit
DESCRIPTION: Verify we can cleanly exit a scheduler in multiple places
OUTPUT:
[ 7.412856] sched_ext: BPF scheduler "exit" enabled
[ 7.427924] sched_ext: BPF scheduler "exit" disabled (unregistered from BPF)
[ 7.466677] sched_ext: BPF scheduler "exit" enabled
[ 7.475923] sched_ext: BPF scheduler "exit" disabled (unregistered from BPF)
[ 7.512803] sched_ext: BPF scheduler "exit" enabled
[ 7.532924] sched_ext: BPF scheduler "exit" disabled (unregistered from BPF)
[ 7.586809] sched_ext: BPF scheduler "exit" enabled
[ 7.595926] sched_ext: BPF scheduler "exit" disabled (unregistered from BPF)
[ 7.661923] sched_ext: BPF scheduler "exit" disabled (unregistered from BPF)
[ 7.723923] sched_ext: BPF scheduler "exit" disabled (unregistered from BPF)
ok 1 exit #
===== END =====
=============================
RESULTS:
PASSED: 1
SKIPPED: 0
FAILED: 0
Fixes: f0e1a0643a59 ("sched_ext: Implement BPF extensible scheduler class")
Signed-off-by: David Vernet <void@manifault.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
If ufshcd_rtc_work calls ufshcd_rpm_put_sync() and the pm's usage_count
is 0, we will enter the runtime suspend callback. However, the runtime
suspend callback will wait to flush ufshcd_rtc_work, causing a deadlock.
Replace ufshcd_rpm_put_sync() with ufshcd_rpm_put() to avoid the
deadlock.
Fixes: 6bf999e0eb41 ("scsi: ufs: core: Add UFS RTC support")
Cc: stable@vger.kernel.org #6.11.x
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Link: https://lore.kernel.org/r/20241024015453.21684-1-peter.wang@mediatek.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If the sg_copy_buffer() call returns less than sdebug_sector_size, then
we drop out of the copy loop. However, we still report that we copied
the full expected amount, which is not proper.
Fix by keeping a running total and return that value.
Fixes: 84f3a3c01d70 ("scsi: scsi_debug: Atomic write support")
Reported-by: Colin Ian King <colin.i.king@gmail.com>
Suggested-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20241018101655.4207-1-john.g.garry@oracle.com
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In commit 63fb3ec80516 ("sched_ext: Allow only user DSQs for
scx_bpf_consume(), scx_bpf_dsq_nr_queued() and bpf_iter_scx_dsq_new()"), we
updated the consume path to only accept user DSQs, thus making it invalid
to consume SCX_DSQ_GLOBAL. This selftest was doing that, so let's create a
custom DSQ and use that instead. The test now passes:
[root@virtme-ng sched_ext]# ./runner -t exit
===== START =====
TEST: exit
DESCRIPTION: Verify we can cleanly exit a scheduler in multiple places
OUTPUT:
[ 12.387229] sched_ext: BPF scheduler "exit" enabled
[ 12.406064] sched_ext: BPF scheduler "exit" disabled (unregistered from BPF)
[ 12.453325] sched_ext: BPF scheduler "exit" enabled
[ 12.474064] sched_ext: BPF scheduler "exit" disabled (unregistered from BPF)
[ 12.515241] sched_ext: BPF scheduler "exit" enabled
[ 12.532064] sched_ext: BPF scheduler "exit" disabled (unregistered from BPF)
[ 12.592063] sched_ext: BPF scheduler "exit" disabled (unregistered from BPF)
[ 12.654063] sched_ext: BPF scheduler "exit" disabled (unregistered from BPF)
[ 12.715062] sched_ext: BPF scheduler "exit" disabled (unregistered from BPF)
ok 1 exit #
===== END =====
Signed-off-by: David Vernet <void@manifault.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The x86 user pointer validation changes made me look at compiler output
a lot, and the wrong indentation for the ".popsection" in the generated
assembler triggered me.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It turns out that AMD has a "Meltdown Lite(tm)" issue with non-canonical
accesses in kernel space. And so using just the high bit to decide
whether an access is in user space or kernel space ends up with the good
old "leak speculative data" if you have the right gadget using the
result:
CVE-2020-12965 “Transient Execution of Non-Canonical Accesses“
Now, the kernel surrounds the access with a STAC/CLAC pair, and those
instructions end up serializing execution on older Zen architectures,
which closes the speculation window.
But that was true only up until Zen 5, which renames the AC bit [1].
That improves performance of STAC/CLAC a lot, but also means that the
speculation window is now open.
Note that this affects not just the new address masking, but also the
regular valid_user_address() check used by access_ok(), and the asm
version of the sign bit check in the get_user() helpers.
It does not affect put_user() or clear_user() variants, since there's no
speculative result to be used in a gadget for those operations.
Reported-by: Andrew Cooper <andrew.cooper3@citrix.com>
Link: https://lore.kernel.org/all/80d94591-1297-4afb-b510-c665efd37f10@citrix.com/
Link: https://lore.kernel.org/all/20241023094448.GAZxjFkEOOF_DM83TQ@fat_crate.local/ [1]
Link: https://www.amd.com/en/resources/product-security/bulletin/amd-sb-1010.html
Link: https://arxiv.org/pdf/2108.10771
Cc: Josh Poimboeuf <jpoimboe@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Tested-by: Maciej Wieczor-Retman <maciej.wieczor-retman@intel.com> # LAM case
Fixes: 2865baf54077 ("x86: support user address masking instead of non-speculative conditional")
Fixes: 6014bc27561f ("x86-64: make access_ok() independent of LAM")
Fixes: b19b74bc99b1 ("x86/mm: Rework address range check in get_user() and put_user()")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
Christoffer Sandberg
Jan Schär
Alexey Klimov
Dmitry Yashin
Qun-Wei Lin
Piyush Raj Chouhan
Barry Song
Jeff Xu
Kirill A. Shutemov
Edward Liaw
Lorenzo Stoakes
Gregory Price
Ryusuke Konishi
Nobuhiro Iwamatsu
Edward Adam Davis
Jeongjun Park
Jann Horn
Sabyrzhan Tasbolatov
Huang Ying
Liam R. Howlett
Matt Fleming
David Hildenbrand
Aleksei Vetrov
Jarkko Sakkinen
Hans de Goede
Ian Rogers
Arnaldo Carvalho de Melo
Christophe JAILLET
Linus Torvalds
Takashi Sakamoto
Armin Wolf
Tejun Heo
David Vernet
Peter Wang
John Garry