| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The calculation of memblock_limit in adjust_lowmem_bounds() assumes that
bank 0 starts from a PMD-aligned address. However, the beginning of the
first bank may be NOMAP memory and the start of usable memory
will be not aligned to PMD boundary. In such case the memblock_limit will
be set to the end of the NOMAP region, which will prevent any memblock
allocations.
Mark the region between the end of the NOMAP area and the next PMD-aligned
address as NOMAP as well, so that the usable memory will start at
PMD-aligned address.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The Armada 38x and other integrated SoCs use a reduced pin count so the
width of the SDRAM interface is smaller than the Armada XP SoCs. This
means that the definition of "full" and "half" width is reduced from
64/32 to 32/16.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add support for the ECC functionality as found in the DDR RAM and L2
cache controllers on the MV78230/MV78x60 SoCs. This driver has been
tested on the MV78460 (on a custom board with a DDR3 ECC DIMM).
[cp use SPDX license]
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
We already have wrappers for x8 and x16, so add the missing x32 one.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The aurora cache on the Marvell Armada-XP SoC supports ECC protection
for the L2 data arrays. Add a "marvell,ecc-enable" device tree property
which can be used to enable this.
[jlu@pengutronix.de: use aurora specific define AURORA_ACR_ECC_EN]
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add documentation for the marvell,ecc-enable properties which can be
used to enable ECC on the Marvell aurora cache.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The aurora cache on the Marvell Armada-XP SoC supports the same tag
parity features as the other l2x0 cache implementations.
[jlu@pengutronix.de: use aurora specific define AURORA_ACR_PARITY_EN]
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
These defines will be used by subsequent patches to add support for the
parity check and error correction functionality in the Aurora L2 cache
controller.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The macro name is too generic, so add a AURORA_ prefix.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
This include file will be used by the AURORA EDAC code.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The stackframe setup when compiled with clang is different.
Since the stack unwinder expects the gcc stackframe setup it
fails to print backtraces. This patch adds support for the
clang stackframe setup.
Link: https://github.com/ClangBuiltLinux/linux/issues/35
Cc: clang-built-linux@googlegroups.com
Suggested-by: Tri Vo <trong@google.com>
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Translation faults arising from cache maintenance instructions are
rather unhelpfully reported with an FSR value where the WnR field is set
to 1, indicating that the faulting access was a write. Since cache
maintenance instructions on 32-bit ARM do not require any particular
permissions, this can cause our private 'cacheflush' system call to fail
spuriously if a translation fault is generated due to page aging when
targetting a read-only VMA.
In this situation, we will return -EFAULT to userspace, although this is
unfortunately suppressed by the popular '__builtin___clear_cache()'
intrinsic provided by GCC, which returns void.
Although it's tempting to write this off as a userspace issue, we can
actually do a little bit better on CPUs that support LPAE, even if the
short-descriptor format is in use. On these CPUs, cache maintenance
faults additionally set the CM field in the FSR, which we can use to
suppress the write permission checks in the page fault handler and
succeed in performing cache maintenance to read-only areas even in the
presence of a translation fault.
Reported-by: Orion Hodson <oth@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Since commit ad67b74d2469d9b8 ("printk: hash addresses printed with
%p"), an obfuscated kernel pointer is printed at every boot if
debugging is enabled:
vdso: 1 text pages at base (____ptrval____)
Remove the print completely, as it's useless without the address.
Based on commit 0f1bf7e39822476b ("arm64/vdso: don't leak kernel
addresses").
Fixes: ad67b74d2469d9b8 ("printk: hash addresses printed with %p")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
When you run "make clean" for arm, it never visits mach-* or plat-*
directories because machine-y and plat-y are just empty.
When cleaning, all machine, plat directories are accumulated to
machine-, plat-, respectively. So, let's pass them to core- to
clean up those directories.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
This open-coded nop as mov r0, r0 is a development history
artifact.
First commit b11fe38883d1
("ARM: 6663/1: make Thumb2 kernel entry point more similar
to the ARM one") moved the code around so that the nops
would come before the conditional thumb instructions, as it
turned out that some boot loaders were patching the initial
nop instructions in the kernel. At this point it is clear
that all mov r0,r0 are open-coded nops.
Then commit 81a0bc39ea19 ("ARM: add UEFI stub support")
moved things around and defined __nop for EFI support and
missed this open-coded nop.
commit 06a4b6d009a1
("ARM: 8677/1: boot/compressed: fix decompressor header
layout for v7-M") makes all invocations of __nop be wide,
but that is fine, because this is what we want: the
mov r0,r0 is inside ifndef CONFIG_THUMB2_KERNEL.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: Roy Franz <rfranz@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
This was unclear to me until Russell explained the obvious
that 8 nops are added to offset an a.out image. Reading
git history reveals that thumb kernels first removed the
nops and then kept 7 of them (the last instruction being
a switch to thumb mode) as it turns out that some boot
loaders were using this as a "patch area". Also the magic
numbers after the initial nops and the jump of course
need to stay in the same offset for kernel file
detection.
Make the code easier to understand with a comment.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: Roy Franz <rfranz@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
To use Fastfpe, a user is supposed to enable CONFIG_FPE_FASTFPE
and put downstream source files into arch/arm/fastfpe/.
It is not working for O= build because $(wildcard arch/arm/fastfpe)
checks if it exists in $(objtree), not in $(srctree).
Add the $(srctree)/ prefix to fix it.
While I was here, I slightly refactored the code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Clang produces references to __aeabi_uidivmod and __aeabi_idivmod for
arm-linux-gnueabi and arm-linux-gnueabihf targets incorrectly when AEABI
is not selected (such as when OABI_COMPAT is selected).
While this means that OABI userspaces wont be able to upgraded to
kernels built with Clang, it means that boards that don't enable AEABI
like s3c2410_defconfig will stop failing to link in KernelCI when built
with Clang.
Link: https://github.com/ClangBuiltLinux/linux/issues/482
Link: https://groups.google.com/forum/#!msg/clang-built-linux/yydsAAux5hk/GxjqJSW-AQAJ
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
There is error from cppcheck tool.
"Shifting signed 32-bit value by 31 bits is undefined behaviour errors"
This error is false positive.
change to use BIT() macro for improvement.
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
This commit removes the open-coded CPU-offline notification with new
common code. In particular, this change avoids calling scheduler code
using RCU from an offline CPU that RCU is ignoring. This is a minimal
change. A more intrusive change might invoke the cpu_check_up_prepare()
and cpu_set_state_online() functions at CPU-online time, which would
allow onlining throw an error if the CPU did not go offline properly.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: linux-arm-kernel@lists.infradead.org
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
clang warns:
arch/arm/mach-iop13xx/pci.c:292:7: warning: logical not is only applied
to the left hand side of this comparison [-Wlogical-not-parentheses]
if (!iop13xx_atux_pci_status(1) == 0)
^ ~~
arch/arm/mach-iop13xx/pci.c:439:7: warning: logical not is only applied
to the left hand side of this comparison [-Wlogical-not-parentheses]
if (!iop13xx_atue_pci_status(1) == 0)
^ ~~
!func() == 0 is equivalent to func(), which clears up this warning and
makes the code more readable.
Link: https://github.com/ClangBuiltLinux/linux/issues/543
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
|
|
The Hyperv vIOMMU file name should be "hyperv-iommu.c" rather
than "hyperv_iommu.c". This patch is to fix it.
Signed-off-by: Lan Tianyu <Tianyu.Lan@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
This patch corrects the SPDX License Identifier style
in the trace header file related to Microsoft Hyper-V
client drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Fix typos in the HyperV toolchain.
Signed-off-by: Adrian Vladu <avladu@cloudbasesolutions.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sasha Levin <sashal@kernel.org>
Cc: Alessandro Pilotti <apilotti@cloudbasesolutions.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
HyperV KVP and VSS daemons should exit with 0 when the '--help'
or '-h' flags are used.
Signed-off-by: Adrian Vladu <avladu@cloudbasesolutions.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sasha Levin <sashal@kernel.org>
Cc: Alessandro Pilotti <apilotti@cloudbasesolutions.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Fixed pep8/flake8 python style code for lsvmbus tool.
The TAB indentation was on purpose ignored (pep8 rule W191) to make
sure the code is complying with the Linux code guideline.
The following command doe not show any warnings now:
pep8 --ignore=W191 lsvmbus
flake8 --ignore=W191 lsvmbus
Signed-off-by: Adrian Vladu <avladu@cloudbasesolutions.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sasha Levin <sashal@kernel.org>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Alessandro Pilotti <apilotti@cloudbasesolutions.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
The initial support for dynamic ftrace trampolines in modules made use
of an indirect branch which loaded its target from the beginning of
a special section (e71a4e1bebaf7 ("arm64: ftrace: add support for far
branches to dynamic ftrace")). Since no instructions were being patched,
no cache maintenance was needed. However, later in be0f272bfc83 ("arm64:
ftrace: emit ftrace-mod.o contents through code") this code was reworked
to output the trampoline instructions directly into the PLT entry but,
unfortunately, the necessary cache maintenance was overlooked.
Add a call to __flush_icache_range() after writing the new trampoline
instructions but before patching in the branch to the trampoline.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: James Morse <james.morse@arm.com>
Cc: <stable@vger.kernel.org>
Fixes: be0f272bfc83 ("arm64: ftrace: emit ftrace-mod.o contents through code")
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Recent gcc compilers (gcc 9.1) generate warnings about an out of bounds
memset, if the memset goes accross several fields of a struct. This
generated a couple of warnings on x86_64 builds in sanitize_boot_params().
Fix this by explicitly saving the fields in struct boot_params
that are intended to be preserved, and zeroing all the rest.
[ tglx: Tagged for stable as it breaks the warning free build there as well ]
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Suggested-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190731054627.5627-2-jhubbard@nvidia.com
|
|
`check_input_term` recursively calls itself with input from
device side (e.g., uac_input_terminal_descriptor.bCSourceID)
as argument (id). In `check_input_term`, if `check_input_term`
is called with the same `id` argument as the caller, it triggers
endless recursive call, resulting kernel space stack overflow.
This patch fixes the bug by adding a bitmap to `struct mixer_build`
to keep track of the checked ids and stop the execution if some id
has been checked (similar to how parse_audio_unit handles unitid
argument).
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Hui Peng <benquike@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch may fix two issues:
First, when IOSQE_IO_DRAIN set, the next IOs need to be inserted into
defer list to delay execution, but link io will be actively scheduled to
run by calling io_queue_sqe.
Second, when multiple LINK_IOs are inserted together with defer_list,
the LINK_IO is no longer keep order.
|-------------|
| LINK_IO | ----> insert to defer_list -----------
|-------------| |
| LINK_IO | ----> insert to defer_list ----------|
|-------------| |
| LINK_IO | ----> insert to defer_list ----------|
|-------------| |
| NORMAL_IO | ----> insert to defer_list ----------|
|-------------| |
|
queue_work at same time <-----|
Fixes: 9e645e1105c ("io_uring: add support for sqe links")
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We had a few issues with this code, and there's still a problem around
how we deal with error handling for chained/split bios. For now, just
revert the code and we'll try again with a thoroug solution. This
reverts commits:
e15c2ffa1091 ("block: fix O_DIRECT error handling for bio fragments")
0eb6ddfb865c ("block: Fix __blkdev_direct_IO() for bio fragments")
6a43074e2f46 ("block: properly handle IOCB_NOWAIT for async O_DIRECT IO")
893a1c97205a ("blk-mq: allow REQ_NOWAIT to return an error inline")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit bd11b3a391e3 ("io_uring: don't use iov_iter_advance() for fixed
buffers") introduced an optimization to avoid using the slow
iov_iter_advance by manually populating the iov_iter iterator in some
cases.
However, the computation of the iterator count field was erroneous: The
first bvec was always accounted for an extent of page size even if the
bvec length was smaller.
In consequence, some I/O operations on fixed buffers were unable to
operate on the full extent of the buffer, consistently skipping some
bytes at the end of it.
Fixes: bd11b3a391e3 ("io_uring: don't use iov_iter_advance() for fixed buffers")
Cc: stable@vger.kernel.org
Signed-off-by: Aleix Roca Nonell <aleix.rocanonell@bsc.es>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
lib/devres.c, which implements devm_ioremap_resource(), is only built
when CONFIG_HAS_IOMEM is set/enabled, so XILINX_SDFEC should depend
on HAS_IOMEM. Fixes this build error (as seen on UML builds):
ERROR: "devm_ioremap_resource" [drivers/misc/xilinx_sdfec.ko] undefined!
Fixes: 76d83e1c3233 ("misc: xilinx-sdfec: add core driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Derek Kiernan <derek.kiernan@xilinx.com>
Cc: Dragan Cvetic <dragan.cvetic@xilinx.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/f9004be5-9925-327b-3ec2-6506e46fe565@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB buffer allocation code is the only place in the usb core (and in
fact the whole kernel) that uses is_device_dma_capable, while the URB
mapping code uses the uses_dma flag in struct usb_bus. Switch the buffer
allocation to use the uses_dma flag used by the rest of the USB code,
and create a helper in hcd.h that checks this flag as well as the
CONFIG_HAS_DMA to simplify the caller a bit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20190811080520.21712-3-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the HCD provides a localmem pool we will never use the DMA pools, so
don't create them.
Fixes: b0310c2f09bb ("USB: use genalloc for USB HCs with local memory")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20190811080520.21712-2-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If driver probe needs to be deferred, e.g. because ci_hdrc_add_device()
isn't ready yet, this driver currently misbehaves badly:
a) success is still reported to the driver core (meaning a 2nd
probe attempt will never be done), leaving the driver in
a dysfunctional state and the hardware unusable
b) driver remove / shutdown OOPSes:
[ 206.786916] Unable to handle kernel paging request at virtual address fffffdff
[ 206.794148] pgd = 880b9f82
[ 206.796890] [fffffdff] *pgd=abf5e861, *pte=00000000, *ppte=00000000
[ 206.803179] Internal error: Oops: 37 [#1] PREEMPT SMP ARM
[ 206.808581] Modules linked in: wl18xx evbug
[ 206.813308] CPU: 1 PID: 1 Comm: systemd-shutdow Not tainted 4.19.35+gf345c93b4195 #1
[ 206.821053] Hardware name: Freescale i.MX7 Dual (Device Tree)
[ 206.826813] PC is at ci_hdrc_remove_device+0x4/0x20
[ 206.831699] LR is at ci_hdrc_imx_remove+0x20/0xe8
[ 206.836407] pc : [<805cd4b0>] lr : [<805d62cc>] psr: 20000013
[ 206.842678] sp : a806be40 ip : 00000001 fp : 80adbd3c
[ 206.847906] r10: 80b1b794 r9 : 80d5dfe0 r8 : a8192c44
[ 206.853136] r7 : 80db93a0 r6 : a8192c10 r5 : a8192c00 r4 : a93a4a00
[ 206.859668] r3 : 00000000 r2 : a8192ce4 r1 : ffffffff r0 : fffffdfb
[ 206.866201] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 206.873341] Control: 10c5387d Table: a9e0c06a DAC: 00000051
[ 206.879092] Process systemd-shutdow (pid: 1, stack limit = 0xb271353c)
[ 206.885624] Stack: (0xa806be40 to 0xa806c000)
[ 206.889992] be40: a93a4a00 805d62cc a8192c1c a8170e10 a8192c10 8049a490 80d04d08 00000000
[ 206.898179] be60: 00000000 80d0da2c fee1dead 00000000 a806a000 00000058 00000000 80148b08
[ 206.906366] be80: 01234567 80148d8c a9858600 00000000 00000000 00000000 00000000 80d04d08
[ 206.914553] bea0: 00000000 00000000 a82741e0 a9858600 00000024 00000002 a9858608 00000005
[ 206.922740] bec0: 0000001e 8022c058 00000000 00000000 a806bf14 a9858600 00000000 a806befc
[ 206.930927] bee0: a806bf78 00000000 7ee12c30 8022c18c a806bef8 a806befc 00000000 00000001
[ 206.939115] bf00: 00000000 00000024 a806bf14 00000005 7ee13b34 7ee12c68 00000004 7ee13f20
[ 206.947302] bf20: 00000010 7ee12c7c 00000005 7ee12d04 0000000a 76e7dc00 00000001 80d0f140
[ 206.955490] bf40: ab637880 a974de40 60000013 80d0f140 ab6378a0 80d04d08 a8080470 a9858600
[ 206.963677] bf60: a9858600 00000000 00000000 8022c24c 00000000 80144310 00000000 00000000
[ 206.971864] bf80: 80101204 80d04d08 00000000 80d04d08 00000000 00000000 00000003 00000058
[ 206.980051] bfa0: 80101204 80101000 00000000 00000000 fee1dead 28121969 01234567 00000000
[ 206.988237] bfc0: 00000000 00000000 00000003 00000058 00000000 00000000 00000000 00000000
[ 206.996425] bfe0: 0049ffb0 7ee13d58 0048a84b 76f245a6 60000030 fee1dead 00000000 00000000
[ 207.004622] [<805cd4b0>] (ci_hdrc_remove_device) from [<805d62cc>] (ci_hdrc_imx_remove+0x20/0xe8)
[ 207.013509] [<805d62cc>] (ci_hdrc_imx_remove) from [<8049a490>] (device_shutdown+0x16c/0x218)
[ 207.022050] [<8049a490>] (device_shutdown) from [<80148b08>] (kernel_restart+0xc/0x50)
[ 207.029980] [<80148b08>] (kernel_restart) from [<80148d8c>] (sys_reboot+0xf4/0x1f0)
[ 207.037648] [<80148d8c>] (sys_reboot) from [<80101000>] (ret_fast_syscall+0x0/0x54)
[ 207.045308] Exception stack(0xa806bfa8 to 0xa806bff0)
[ 207.050368] bfa0: 00000000 00000000 fee1dead 28121969 01234567 00000000
[ 207.058554] bfc0: 00000000 00000000 00000003 00000058 00000000 00000000 00000000 00000000
[ 207.066737] bfe0: 0049ffb0 7ee13d58 0048a84b 76f245a6
[ 207.071799] Code: ebffffa8 e3a00000 e8bd8010 e92d4010 (e5904004)
[ 207.078021] ---[ end trace be47424e3fd46e9f ]---
[ 207.082647] Kernel panic - not syncing: Fatal exception
[ 207.087894] ---[ end Kernel panic - not syncing: Fatal exception ]---
c) the error path in combination with driver removal causes
imbalanced calls to the clk_*() and pm_()* APIs
a) happens because the original intended return value is
overwritten (with 0) by the return code of
regulator_disable() in ci_hdrc_imx_probe()'s error path
b) happens because ci_pdev is -EPROBE_DEFER, which causes
ci_hdrc_remove_device() to OOPS
Fix a) by being more careful in ci_hdrc_imx_probe()'s error
path and not overwriting the real error code
Fix b) by calling the respective cleanup functions during
remove only when needed (when ci_pdev != NULL, i.e. when
everything was initialised correctly). This also has the
side effect of not causing imbalanced clk_*() and pm_*()
API calls as part of the error code path.
Fixes: 7c8e8909417e ("usb: chipidea: imx: add HSIC support")
Signed-off-by: André Draszik <git@andred.net>
Cc: stable <stable@vger.kernel.org>
CC: Peter Chen <Peter.Chen@nxp.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Pengutronix Kernel Team <kernel@pengutronix.de>
CC: Fabio Estevam <festevam@gmail.com>
CC: NXP Linux Team <linux-imx@nxp.com>
CC: linux-usb@vger.kernel.org
CC: linux-arm-kernel@lists.infradead.org
CC: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190810150758.17694-1-git@andred.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On the Gemini SoC the FOTG2 stalls after port reset
so restart the HCD after each port reset.
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190810150458.817-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A few checks checked for the size of the pointer to a structure
instead of the structure itself. Copy & paste issue presumably.
Fixes: e4c6fb7794982 ("usbnet: move the CDC parser into USB core")
Cc: stable <stable@vger.kernel.org>
Reported-by: syzbot+45a53506b65321c1fe91@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20190813093541.18889-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
destroy() will decrement the refcount on the interface, so that
it needs to be taken so early that it never undercounts.
Fixes: 7fb57a019f94e ("USB: cdc-acm: Fix potential deadlock (lockdep warning)")
Cc: stable <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+1b2449b7b5dc240d107a@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20190808142119.7998-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a VID:PID for the BroadMobi BM818 M.2 card
T: Bus=01 Lev=03 Prnt=40 Port=03 Cnt=01 Dev#= 44 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2020 ProdID=2060 Rev=00.00
S: Manufacturer=Qualcomm, Incorporated
S: Product=Qualcomm CDMA Technologies MSM
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=(none)
I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
Signed-off-by: Bob Ham <bob.ham@puri.sm>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: stable <stable@vger.kernel.org>
[ johan: use USB_DEVICE_INTERFACE_CLASS() ]
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
On Motorola Mapphone devices such as Droid 4 there are five USB ports
that do not use the same layout as Gobi 1K/2K/etc devices listed in
qcserial.c. So we should use qcaux.c or option.c as noted by
Dan Williams <dan.j.williams@intel.com>.
As the Motorola USB serial ports have an interrupt endpoint as shown
with lsusb -v, we should use option.c instead of qcaux.c as pointed out
by Johan Hovold <johan@kernel.org>.
The ff/ff/ff interfaces seem to always be UARTs on Motorola devices.
For the other interfaces, class 0x0a (CDC Data) should not in general
be added as they are typically part of a multi-interface function as
noted earlier by Bjørn Mork <bjorn@mork.no>.
However, looking at the Motorola mapphone kernel code, the mdm6600 0x0a
class is only used for flashing the modem firmware, and there are no
other interfaces. So I've added that too with more details below as it
works just fine.
The ttyUSB ports on Droid 4 are:
ttyUSB0 DIAG, CQDM-capable
ttyUSB1 MUX or NMEA, no response
ttyUSB2 MUX or NMEA, no response
ttyUSB3 TCMD
ttyUSB4 AT-capable
The ttyUSB0 is detected as QCDM capable by ModemManager. I think
it's only used for debugging with ModemManager --debug for sending
custom AT commands though. ModemManager already can manage data
connection using the USB QMI ports that are already handled by the
qmi_wwan.c driver.
To enable the MUX or NMEA ports, it seems that something needs to be
done additionally to enable them, maybe via the DIAG or TCMD port.
It might be just a NVRAM setting somewhere, but I have no idea what
NVRAM settings may need changing for that.
The TCMD port seems to be a Motorola custom protocol for testing
the modem and to configure it's NVRAM and seems to work just fine
based on a quick test with a minimal tcmdrw tool I wrote.
The voice modem AT-capable port seems to provide only partial
support, and no PM support compared to the TS 27.010 based UART
wired directly to the modem.
The UARTs added with this change are the same product IDs as the
Motorola Mapphone Android Linux kernel mdm6600_id_table. I don't
have any mdm9600 based devices, so I have only tested these on
mdm6600 based droid 4.
Then for the class 0x0a (CDC Data) mode, the Motorola Mapphone Android
Linux kernel driver moto_flashqsc.c just seems to change the
port->bulk_out_size to 8K from the default. And is only used for
flashing the modem firmware it seems.
I've verified that flashing the modem with signed firmware works just
fine with the option driver after manually toggling the GPIO pins, so
I've added droid 4 modem flashing mode to the option driver. I've not
added the other devices listed in moto_flashqsc.c in case they really
need different port->bulk_out_size. Those can be added as they get
tested to work for flashing the modem.
After this patch the output of /sys/kernel/debug/usb/devices has
the following for normal 22b8:2a70 mode including the related qmi_wwan
interfaces:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=22b8 ProdID=2a70 Rev= 0.00
S: Manufacturer=Motorola, Incorporated
S: Product=Flash MZ600
C:* #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=8a(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 7 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=8b(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=8c(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=08(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=8d(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=09(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
In 22b8:900e "qc_dload" mode the device shows up as:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=22b8 ProdID=900e Rev= 0.00
S: Manufacturer=Motorola, Incorporated
S: Product=Flash MZ600
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
And in 22b8:4281 "ram_downloader" mode the device shows up as:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=22b8 ProdID=4281 Rev= 0.00
S: Manufacturer=Motorola, Incorporated
S: Product=Flash MZ600
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=fc Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
Cc: Bjørn Mork <bjorn@mork.no>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Lars Melin <larsm17@gmail.com>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
There are a few different subsystems in the kernel that depend on model
specific behaviour (perf, EDAC, power, ...). Easier for just one person
to have the task to get new model numbers included instead of having
these groups trip over each other to do it.
[ bp: s/Cpu/CPU/ and add x86@kernel.org so that it gets CCed too as
FYI. ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190814234030.30817-1-tony.luck@intel.com
|
|
I -thought- I had fixed this entirely, but it looks like that I didn't
test this thoroughly enough as we apparently still make one big mistake
with nv50_msto_atomic_check() - we don't handle the following scenario:
* CRTC #1 has n VCPI allocated to it, is attached to connector DP-4
which is attached to encoder #1. enabled=y active=n
* CRTC #1 is changed from DP-4 to DP-5, causing:
* DP-4 crtc=#1→NULL (VCPI n→0)
* DP-5 crtc=NULL→#1
* CRTC #1 steals encoder #1 back from DP-4 and gives it to DP-5
* CRTC #1 maintains the same mode as before, just with a different
connector
* mode_changed=n connectors_changed=y
(we _SHOULD_ do VCPI 0→n here, but don't)
Once the above scenario is repeated once, we'll attempt freeing VCPI
from the connector that we didn't allocate due to the connectors
changing, but the mode staying the same. Sigh.
Since nv50_msto_atomic_check() has broken a few times now, let's rethink
things a bit to be more careful: limit both VCPI/PBN allocations to
mode_changed || connectors_changed, since neither VCPI or PBN should
ever need to change outside of routing and mode changes.
Changes since v1:
* Fix accidental reversal of clock and bpp arguments in
drm_dp_calc_pbn_mode() - William Lewis
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reported-by: Bohdan Milar <bmilar@redhat.com>
Tested-by: Bohdan Milar <bmilar@redhat.com>
Fixes: 232c9eec417a ("drm/nouveau: Use atomic VCPI helpers for MST")
References: 412e85b60531 ("drm/nouveau: Only release VCPI slots on mode changes")
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@redhat.com>
Cc: Jerry Zuo <Jerry.Zuo@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Juston Li <juston.li@intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Karol Herbst <karolherbst@gmail.com>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: <stable@vger.kernel.org> # v5.1+
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190809005307.18391-1-lyude@redhat.com
|
|
There is another thread still access standard VGA I/O while loading drm driver.
Disable standard VGA I/O decode to avoid this issue.
Signed-off-by: Y.C. Chen <yc_chen@aspeedtech.com>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1523410059-18415-1-git-send-email-yc_chen@aspeedtech.com
|
|
Diverged from what the code does with commit 530210c7814e ("of/irq: Replace
of_irq with of_phandle_args").
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The proper way to add additional contraints to an existing json-schema
is using 'allOf' to reference the base schema. Using just '$ref' doesn't
work. Fix this for the 'st,syscfg' property.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The spsc_queue_peek function is accessing queue->head which belongs to
the consumer thread and shouldn't be accessed by the producer
This is fixing a rare race condition when destroying entities.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Monk.liu@amd.com
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Make the __fstate_clean() function correctly set the
state of sstatus.FS in pt_regs to SR_FS_CLEAN.
Fixes: 7db91e57a0acd ("RISC-V: Task implementation")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[paul.walmsley@sifive.com: expanded "Fixes" commit ID]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
The following two reasons cause FP registers are sometimes not
initialized before starting the user program.
1. Currently, the FP context is initialized in flush_thread() function
and we expect these initial values to be restored to FP register when
doing FP context switch. However, the FP context switch only occurs in
switch_to function. Hence, if this process does not be scheduled out
and scheduled in before entering the user space, the FP registers
have no chance to initialize.
2. In flush_thread(), the state of reg->sstatus.FS inherits from the
parent. Hence, the state of reg->sstatus.FS may be dirty. If this
process is scheduled out during flush_thread() and initializing the
FP register, the fstate_save() in switch_to will corrupt the FP context
which has been initialized until flush_thread().
To solve the 1st case, the initialization of the FP register will be
completed in start_thread(). It makes sure all FP registers are initialized
before starting the user program. For the 2nd case, the state of
reg->sstatus.FS in start_thread will be set to SR_FS_OFF to prevent this
process from corrupting FP context in doing context save. The FP state is
set to SR_FS_INITIAL in start_trhead().
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Fixes: 7db91e57a0acd ("RISC-V: Task implementation")
Cc: stable@vger.kernel.org
[paul.walmsley@sifive.com: fixed brace alignment issue reported by
checkpatch]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
Mike Rapoport
Chris Packham
Jan Luebbe
Nathan Huckleberry
Will Deacon
Geert Uytterhoeven
Masahiro Yamada
Linus Walleij
Nick Desaulniers
Phong Tran
Paul E. McKenney
Nathan Chancellor
Linus Torvalds
Lan Tianyu
Nishad Kamdar
Adrian Vladu
John Hubbard
Hui Peng
Jackie Liu
Jens Axboe
Aleix Roca Nonell
Randy Dunlap
Christoph Hellwig
André Draszik
Hans Ulli Kroll
Oliver Neukum
Bob Ham
Tony Lindgren
Tony Luck
Lyude Paul
Y.C. Chen
Lubomir Rintel
Rob Herring
Christian König
Vincent Chen