| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Override the hardware strap configuration for MDI-X mode to ensure a
predictable initial state for the driver. The initial mode of the LAN87xx
PHY is determined by the AUTOMDIX_EN strap pin, but the driver has no
documented way to read its latched status.
This unpredictability means the driver cannot know if the PHY has
initialized with Auto-MDIX enabled or disabled, preventing it from
providing a reliable interface to the user.
This patch introduces a `config_init` hook that forces the PHY into a
known state by explicitly enabling Auto-MDIX.
Fixes: 05b35e7eb9a1 ("smsc95xx: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andre Edich <andre.edich@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250703114941.3243890-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Correct the Auto-MDIX configuration to ensure userspace settings are
respected when the feature is disabled by the AUTOMDIX_EN hardware strap.
The LAN9500 PHY allows its default MDI-X mode to be configured via a
hardware strap. If this strap sets the default to "MDI-X off", the
driver was previously unable to enable Auto-MDIX from userspace.
When handling the ETH_TP_MDI_AUTO case, the driver would set the
SPECIAL_CTRL_STS_AMDIX_ENABLE_ bit but neglected to set the required
SPECIAL_CTRL_STS_OVRRD_AMDIX_ bit. Without the override flag, the PHY
falls back to its hardware strap default, ignoring the software request.
This patch corrects the behavior by also setting the override bit when
enabling Auto-MDIX. This ensures that the userspace configuration takes
precedence over the hardware strap, allowing Auto-MDIX to be enabled
correctly in all scenarios.
Fixes: 05b35e7eb9a1 ("smsc95xx: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andre Edich <andre.edich@microchip.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250703114941.3243890-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
According to the Synopsys Controller IP XGMAC-10G Ethernet MAC Databook
v3.30a (section 2.7.2), when the INTM bit in the DMA_Mode register is set
to 2, the sbd_perch_tx_intr_o[] and sbd_perch_rx_intr_o[] signals operate
in level-triggered mode. However, in this configuration, the DMA does not
assert the XGMAC_NIS status bit for Rx or Tx interrupt events.
This creates a functional regression where the condition
if (likely(intr_status & XGMAC_NIS)) in dwxgmac2_dma_interrupt() will
never evaluate to true, preventing proper interrupt handling for
level-triggered mode. The hardware specification explicitly states that
"The DMA does not assert the NIS status bit for the Rx or Tx interrupt
events" (Synopsys DWC_XGMAC2 Databook v3.30a, sec. 2.7.2).
The fix ensures correct handling of both edge and level-triggered
interrupts while maintaining backward compatibility with existing
configurations. It has been tested on the hardware device (not publicly
available), and it can properly trigger the RX and TX interrupt handling
in both the INTM=0 and INTM=2 configurations.
Fixes: d6ddfacd95c7 ("net: stmmac: Add DMA related callbacks for XGMAC2")
Tested-by: EricChan <chenchuangyu@xiaomi.com>
Signed-off-by: EricChan <chenchuangyu@xiaomi.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250703020449.105730-1-chenchuangyu@xiaomi.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Under some circumstances, the compiler will emit the following warning for
rxrpc_send_response():
net/rxrpc/output.c: In function 'rxrpc_send_response':
net/rxrpc/output.c:974:1: warning: the frame size of 1160 bytes is larger than 1024 bytes
This occurs because the local variables include a 16-element scatterlist
array and a 16-element bio_vec array. It's probably not actually a problem
as this function is only called by the rxrpc I/O thread function in a
kernel thread and there won't be much on the stack before it.
Fix this by overlaying the bio_vec array over the kvec array in the
rxrpc_local struct. There is one of these per I/O thread and the kvec
array is intended for pointing at bits of a packet to be transmitted,
typically a DATA or an ACK packet. As packets for a local endpoint are
only transmitted by its specific I/O thread, there can be no race, and so
overlaying this bit of memory should be no problem.
Fixes: 5800b1cf3fd8 ("rxrpc: Allow CHALLENGEs to the passed to the app for a RESPONSE")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202506240423.E942yKJP-lkp@intel.com/
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org
Link: https://patch.msgid.link/20250707102435.2381045-2-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If an error occurs after a successful airoha_hw_init() call,
airoha_ppe_deinit() needs to be called as already done in the remove
function.
Fixes: 00a7678310fe ("net: airoha: Introduce flowtable offload support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/1c940851b4fa3c3ed2a142910c821493a136f121.1746715755.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support returning VMADDR_CID_LOCAL in case no other vsock transport is
available.
Fixes: 0e12190578d0 ("vsock: add local transport support in the vsock core")
Suggested-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Michal Luczaj <mhal@rbox.co>
Link: https://patch.msgid.link/20250703-vsock-transports-toctou-v4-3-98f0eb530747@rbox.co
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Transport assignment may race with module unload. Protect new_transport
from becoming a stale pointer.
This also takes care of an insecure call in vsock_use_local_transport();
add a lockdep assert.
BUG: unable to handle page fault for address: fffffbfff8056000
Oops: Oops: 0000 [#1] SMP KASAN
RIP: 0010:vsock_assign_transport+0x366/0x600
Call Trace:
vsock_connect+0x59c/0xc40
__sys_connect+0xe8/0x100
__x64_sys_connect+0x6e/0xc0
do_syscall_64+0x92/0x1c0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
Fixes: c0cfa2d8a788 ("vsock: add multi-transports support")
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Michal Luczaj <mhal@rbox.co>
Link: https://patch.msgid.link/20250703-vsock-transports-toctou-v4-2-98f0eb530747@rbox.co
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
vsock_find_cid() and vsock_dev_do_ioctl() may race with module unload.
transport_{g2h,h2g} may become NULL after the NULL check.
Introduce vsock_transport_local_cid() to protect from a potential
null-ptr-deref.
KASAN: null-ptr-deref in range [0x0000000000000118-0x000000000000011f]
RIP: 0010:vsock_find_cid+0x47/0x90
Call Trace:
__vsock_bind+0x4b2/0x720
vsock_bind+0x90/0xe0
__sys_bind+0x14d/0x1e0
__x64_sys_bind+0x6e/0xc0
do_syscall_64+0x92/0x1c0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
KASAN: null-ptr-deref in range [0x0000000000000118-0x000000000000011f]
RIP: 0010:vsock_dev_do_ioctl.isra.0+0x58/0xf0
Call Trace:
__x64_sys_ioctl+0x12d/0x190
do_syscall_64+0x92/0x1c0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
Fixes: c0cfa2d8a788 ("vsock: add multi-transports support")
Suggested-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Michal Luczaj <mhal@rbox.co>
Link: https://patch.msgid.link/20250703-vsock-transports-toctou-v4-1-98f0eb530747@rbox.co
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add check for the return value of rcar_gen4_ptp_alloc()
to prevent potential null pointer dereference.
Fixes: b0d3969d2b4d ("net: ethernet: rtsn: Add support for Renesas Ethernet-TSN")
Cc: stable@vger.kernel.org
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://patch.msgid.link/20250703100109.2541018-1-haoxiang_li2024@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The datasheets refer to the first Ethernet controller as GMAC0, not
EMAC0.
Rename the compatible string to align with the datasheets. A fix for
the device trees will be sent separately.
Fixes: 0454b9057e98 ("dt-bindings: net: sun8i-emac: Add A523 EMAC0 compatible")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250628054438.2864220-2-wens@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Syzkaller reported a bug [1] where sk->sk_forward_alloc can overflow.
When we send data, if an skb exists at the tail of the write queue, the
kernel will attempt to append the new data to that skb. However, the code
that checks for available space in the skb is flawed:
'''
copy = size_goal - skb->len
'''
The types of the variables involved are:
'''
copy: ssize_t (s64 on 64-bit systems)
size_goal: int
skb->len: unsigned int
'''
Due to C's type promotion rules, the signed size_goal is converted to an
unsigned int to match skb->len before the subtraction. The result is an
unsigned int.
When this unsigned int result is then assigned to the s64 copy variable,
it is zero-extended, preserving its non-negative value. Consequently, copy
is always >= 0.
Assume we are sending 2GB of data and size_goal has been adjusted to a
value smaller than skb->len. The subtraction will result in copy holding a
very large positive integer. In the subsequent logic, this large value is
used to update sk->sk_forward_alloc, which can easily cause it to overflow.
The syzkaller reproducer uses TCP_REPAIR to reliably create this
condition. However, this can also occur in real-world scenarios. The
tcp_bound_to_half_wnd() function can also reduce size_goal to a small
value. This would cause the subsequent tcp_wmem_schedule() to set
sk->sk_forward_alloc to a value close to INT_MAX. Further memory
allocation requests would then cause sk_forward_alloc to wrap around and
become negative.
[1]: https://syzkaller.appspot.com/bug?extid=de6565462ab540f50e47
Reported-by: syzbot+de6565462ab540f50e47@syzkaller.appspotmail.com
Fixes: 270a1c3de47e ("tcp: Support MSG_SPLICE_PAGES")
Signed-off-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Howells <dhowells@redhat.com>
Link: https://patch.msgid.link/20250707054112.101081-1-jiayuan.chen@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Initialize u64 stats as it uses seq counter on 32bit machines
as suggested by lockdep below.
[ 1.830953][ T1] INFO: trying to register non-static key.
[ 1.830993][ T1] The code is fine but needs lockdep annotation, or maybe
[ 1.831027][ T1] you didn't initialize this object before use?
[ 1.831057][ T1] turning off the locking correctness validator.
[ 1.831090][ T1] CPU: 1 UID: 0 PID: 1 Comm: swapper/0 Tainted: G W 6.16.0-rc2-v7l+ #1 PREEMPT
[ 1.831097][ T1] Tainted: [W]=WARN
[ 1.831099][ T1] Hardware name: BCM2711
[ 1.831101][ T1] Call trace:
[ 1.831104][ T1] unwind_backtrace from show_stack+0x18/0x1c
[ 1.831120][ T1] show_stack from dump_stack_lvl+0x8c/0xcc
[ 1.831129][ T1] dump_stack_lvl from register_lock_class+0x9e8/0x9fc
[ 1.831141][ T1] register_lock_class from __lock_acquire+0x420/0x22c0
[ 1.831154][ T1] __lock_acquire from lock_acquire+0x130/0x3f8
[ 1.831166][ T1] lock_acquire from bcmgenet_get_stats64+0x4a4/0x4c8
[ 1.831176][ T1] bcmgenet_get_stats64 from dev_get_stats+0x4c/0x408
[ 1.831184][ T1] dev_get_stats from rtnl_fill_stats+0x38/0x120
[ 1.831193][ T1] rtnl_fill_stats from rtnl_fill_ifinfo+0x7f8/0x1890
[ 1.831203][ T1] rtnl_fill_ifinfo from rtmsg_ifinfo_build_skb+0xd0/0x138
[ 1.831214][ T1] rtmsg_ifinfo_build_skb from rtmsg_ifinfo+0x48/0x8c
[ 1.831225][ T1] rtmsg_ifinfo from register_netdevice+0x8c0/0x95c
[ 1.831237][ T1] register_netdevice from register_netdev+0x28/0x40
[ 1.831247][ T1] register_netdev from bcmgenet_probe+0x690/0x6bc
[ 1.831255][ T1] bcmgenet_probe from platform_probe+0x64/0xbc
[ 1.831263][ T1] platform_probe from really_probe+0xd0/0x2d4
[ 1.831269][ T1] really_probe from __driver_probe_device+0x90/0x1a4
[ 1.831273][ T1] __driver_probe_device from driver_probe_device+0x38/0x11c
[ 1.831278][ T1] driver_probe_device from __driver_attach+0x9c/0x18c
[ 1.831282][ T1] __driver_attach from bus_for_each_dev+0x84/0xd4
[ 1.831291][ T1] bus_for_each_dev from bus_add_driver+0xd4/0x1f4
[ 1.831303][ T1] bus_add_driver from driver_register+0x88/0x120
[ 1.831312][ T1] driver_register from do_one_initcall+0x78/0x360
[ 1.831320][ T1] do_one_initcall from kernel_init_freeable+0x2bc/0x314
[ 1.831331][ T1] kernel_init_freeable from kernel_init+0x1c/0x144
[ 1.831339][ T1] kernel_init from ret_from_fork+0x14/0x20
[ 1.831344][ T1] Exception stack(0xf082dfb0 to 0xf082dff8)
[ 1.831349][ T1] dfa0: 00000000 00000000 00000000 00000000
[ 1.831353][ T1] dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 1.831356][ T1] dfe0: 00000000 00000000 00000000 00000000 00000013 00000000
Fixes: 59aa6e3072aa ("net: bcmgenet: switch to use 64bit statistics")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Ryo Takakura <ryotkkr98@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250702092417.46486-1-ryotkkr98@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot reported a null-ptr-deref in tipc_conn_close() during netns
dismantle. [0]
tipc_topsrv_stop() iterates tipc_net(net)->topsrv->conn_idr and calls
tipc_conn_close() for each tipc_conn.
The problem is that tipc_conn_close() is called after releasing the
IDR lock.
At the same time, there might be tipc_conn_recv_work() running and it
could call tipc_conn_close() for the same tipc_conn and release its
last ->kref.
Once we release the IDR lock in tipc_topsrv_stop(), there is no
guarantee that the tipc_conn is alive.
Let's hold the ref before releasing the lock and put the ref after
tipc_conn_close() in tipc_topsrv_stop().
[0]:
BUG: KASAN: use-after-free in tipc_conn_close+0x122/0x140 net/tipc/topsrv.c:165
Read of size 8 at addr ffff888099305a08 by task kworker/u4:3/435
CPU: 0 PID: 435 Comm: kworker/u4:3 Not tainted 4.19.204-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: netns cleanup_net
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1fc/0x2ef lib/dump_stack.c:118
print_address_description.cold+0x54/0x219 mm/kasan/report.c:256
kasan_report_error.cold+0x8a/0x1b9 mm/kasan/report.c:354
kasan_report mm/kasan/report.c:412 [inline]
__asan_report_load8_noabort+0x88/0x90 mm/kasan/report.c:433
tipc_conn_close+0x122/0x140 net/tipc/topsrv.c:165
tipc_topsrv_stop net/tipc/topsrv.c:701 [inline]
tipc_topsrv_exit_net+0x27b/0x5c0 net/tipc/topsrv.c:722
ops_exit_list+0xa5/0x150 net/core/net_namespace.c:153
cleanup_net+0x3b4/0x8b0 net/core/net_namespace.c:553
process_one_work+0x864/0x1570 kernel/workqueue.c:2153
worker_thread+0x64c/0x1130 kernel/workqueue.c:2296
kthread+0x33f/0x460 kernel/kthread.c:259
ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:415
Allocated by task 23:
kmem_cache_alloc_trace+0x12f/0x380 mm/slab.c:3625
kmalloc include/linux/slab.h:515 [inline]
kzalloc include/linux/slab.h:709 [inline]
tipc_conn_alloc+0x43/0x4f0 net/tipc/topsrv.c:192
tipc_topsrv_accept+0x1b5/0x280 net/tipc/topsrv.c:470
process_one_work+0x864/0x1570 kernel/workqueue.c:2153
worker_thread+0x64c/0x1130 kernel/workqueue.c:2296
kthread+0x33f/0x460 kernel/kthread.c:259
ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:415
Freed by task 23:
__cache_free mm/slab.c:3503 [inline]
kfree+0xcc/0x210 mm/slab.c:3822
tipc_conn_kref_release net/tipc/topsrv.c:150 [inline]
kref_put include/linux/kref.h:70 [inline]
conn_put+0x2cd/0x3a0 net/tipc/topsrv.c:155
process_one_work+0x864/0x1570 kernel/workqueue.c:2153
worker_thread+0x64c/0x1130 kernel/workqueue.c:2296
kthread+0x33f/0x460 kernel/kthread.c:259
ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:415
The buggy address belongs to the object at ffff888099305a00
which belongs to the cache kmalloc-512 of size 512
The buggy address is located 8 bytes inside of
512-byte region [ffff888099305a00, ffff888099305c00)
The buggy address belongs to the page:
page:ffffea000264c140 count:1 mapcount:0 mapping:ffff88813bff0940 index:0x0
flags: 0xfff00000000100(slab)
raw: 00fff00000000100 ffffea00028b6b88 ffffea0002cd2b08 ffff88813bff0940
raw: 0000000000000000 ffff888099305000 0000000100000006 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888099305900: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff888099305980: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff888099305a00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff888099305a80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff888099305b00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: c5fa7b3cf3cb ("tipc: introduce new TIPC server infrastructure")
Reported-by: syzbot+d333febcf8f4bc5f6110@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=27169a847a70550d17be
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Tung Nguyen <tung.quang.nguyen@est.tech>
Link: https://patch.msgid.link/20250702014350.692213-1-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
From commit 634f1a7110b4 ("vsock: support sockmap"), `struct proto
vsock_proto`, defined in af_vsock.c, is not static anymore, since it's
used by vsock_bpf.c.
If CONFIG_BPF_SYSCALL is not defined, `make C=2` will print a warning:
$ make O=build C=2 W=1 net/vmw_vsock/
...
CC [M] net/vmw_vsock/af_vsock.o
CHECK ../net/vmw_vsock/af_vsock.c
../net/vmw_vsock/af_vsock.c:123:14: warning: symbol 'vsock_proto' was not declared. Should it be static?
Declare `vsock_proto` regardless of CONFIG_BPF_SYSCALL, since it's defined
in af_vsock.c, which is built regardless of CONFIG_BPF_SYSCALL.
Fixes: 634f1a7110b4 ("vsock: support sockmap")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://patch.msgid.link/20250703112329.28365-1-sgarzare@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Netlink has this pattern in some places
if (atomic_read(&sk->sk_rmem_alloc) > sk->sk_rcvbuf)
atomic_add(skb->truesize, &sk->sk_rmem_alloc);
, which has the same problem fixed by commit 5a465a0da13e ("udp:
Fix multiple wraparounds of sk->sk_rmem_alloc.").
For example, if we set INT_MAX to SO_RCVBUFFORCE, the condition
is always false as the two operands are of int.
Then, a single socket can eat as many skb as possible until OOM
happens, and we can see multiple wraparounds of sk->sk_rmem_alloc.
Let's fix it by using atomic_add_return() and comparing the two
variables as unsigned int.
Before:
[root@fedora ~]# ss -f netlink
Recv-Q Send-Q Local Address:Port Peer Address:Port
-1668710080 0 rtnl:nl_wraparound/293 *
After:
[root@fedora ~]# ss -f netlink
Recv-Q Send-Q Local Address:Port Peer Address:Port
2147483072 0 rtnl:nl_wraparound/290 *
^
`--- INT_MAX - 576
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Jason Baron <jbaron@akamai.com>
Closes: https://lore.kernel.org/netdev/cover.1750285100.git.jbaron@akamai.com/
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250704054824.1580222-1-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The previous commit unintentionally removed the code responsible for
enabling WoL via MMD3 register 0x8012 BIT5. As a result, Wake-on-LAN
(WoL) support for the QCA808X PHY is no longer functional.
The WoL (Wake-on-LAN) feature for the QCA808X PHY is enabled via MMD3
register 0x8012, BIT5. This implementation is aligned with the approach
used in at8031_set_wol().
Fixes: e58f30246c35 ("net: phy: at803x: fix the wol setting functions")
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250704-qcom_phy_wol_support-v1-2-053342b1538d@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the WoL (Wake-on-LAN) functionality to a shared library to enable
its reuse by the QCA808X PHY driver, incorporating support for WoL
functionality similar to the implementation in at8031_set_wol().
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Link: https://patch.msgid.link/20250704-qcom_phy_wol_support-v1-1-053342b1538d@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
I received a kernel-test-bot report[1] that shows the
[-Wunused-but-set-variable] warning. Since the previous commit I made, as
the 'Fixes' tag shows, gives users an option to turn on and off the
CONFIG_RFS_ACCEL, the issue then can be discovered and reproduced with
GCC specifically.
Like Simon and Jakub suggested, use fewer #ifdefs which leads to fewer
bugs.
[1]
All warnings (new ones prefixed by >>):
drivers/net/ethernet/broadcom/bnxt/bnxt.c: In function 'bnxt_request_irq':
>> drivers/net/ethernet/broadcom/bnxt/bnxt.c:10703:9: warning: variable 'j' set but not used [-Wunused-but-set-variable]
10703 | int i, j, rc = 0;
| ^
Fixes: 9b6a30febddf ("net: allow rps/rfs related configs to be switched")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202506282102.x1tXt0qz-lkp@intel.com/
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Upon receiving HCI_EVT_LE_BIG_SYNC_ESTABLISHED with status 0x00
(success) the corresponding BIS hci_conn state shall be set to
BT_CONNECTED otherwise they will be left with BT_OPEN which is invalid
at that point, also create the debugfs and sysfs entries following the
same logic as the likes of Broadcast Source BIS and CIS connections.
Fixes: f777d8827817 ("Bluetooth: ISO: Notify user space about failed bis connections")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
BIS/PA connections do have their own cleanup proceedure which are
performed by hci_conn_cleanup/bis_cleanup.
Fixes: 23205562ffc8 ("Bluetooth: separate CIS_LINK and BIS_LINK link types")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The check for destination to be BDADDR_ANY is no longer necessary with
the introduction of BIS_LINK.
Fixes: 23205562ffc8 ("Bluetooth: separate CIS_LINK and BIS_LINK link types")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
As the code comments on hci_setup_ext_adv_instance_sync suggests the
advertising instance needs to be disabled in order to update its
parameters, but it was wrongly checking that !adv->pending.
Fixes: cba6b758711c ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
In vmci_transport_packet_init memset the vmci_transport_packet before
populating the fields to avoid any uninitialised data being left in the
structure.
Cc: Bryan Tan <bryan-bt.tan@broadcom.com>
Cc: Vishnu Dasa <vishnu.dasa@broadcom.com>
Cc: Broadcom internal kernel review list
Cc: Stefano Garzarella <sgarzare@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Simon Horman <horms@kernel.org>
Cc: virtualization@lists.linux.dev
Cc: netdev@vger.kernel.org
Cc: stable <stable@kernel.org>
Signed-off-by: HarshaVardhana S A <harshavardhana.sa@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: d021c344051a ("VSOCK: Introduce VM Sockets")
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://patch.msgid.link/20250701122254.2397440-1-gregkh@linuxfoundation.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Examples should be complete and should not have a 'status' property,
especially a disabled one because this disables the dt_binding_check of
the example against the schema. Dropping 'status' property shows
missing other properties - phy-mode and phy-handle.
Fixes: 114508a89ddc ("dt-bindings: net: Add support for Sophgo SG2044 dwmac")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Reviewed-by: Chen Wang <unicorn_wang@outlook.com>
Link: https://patch.msgid.link/20250701063621.23808-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
For NGBE devices, the queue number is limited to be 1 when SRIOV is
enabled. In this case, IRQ vector[0] is used for MISC and vector[1] is
used for queue, based on the previous patches. But for the hardware
design, the IRQ vector[1] must be allocated for use by the VF[6] when
the number of VFs is 7. So the IRQ vector[0] should be shared for PF
MISC and QUEUE interrupts.
+-----------+----------------------+
| Vector | Assigned To |
+-----------+----------------------+
| Vector 0 | PF MISC and QUEUE |
| Vector 1 | VF 6 |
| Vector 2 | VF 5 |
| Vector 3 | VF 4 |
| Vector 4 | VF 3 |
| Vector 5 | VF 2 |
| Vector 6 | VF 1 |
| Vector 7 | VF 0 |
+-----------+----------------------+
Minimize code modifications, only adjust the IRQ vector number for this
case.
Fixes: 877253d2cbf2 ("net: ngbe: add sriov function support")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://patch.msgid.link/20250701063030.59340-4-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Due to hardware limitations of NGBE, queue IRQs can only be requested
on vector 0 to 7. When the number of queues is set to the maximum 8,
the PCI IRQ vectors are allocated from 0 to 8. The vector 0 is used by
MISC interrupt, and althrough the vector 8 is used by queue interrupt,
it is unable to receive packets. This will cause some packets to be
dropped when RSS is enabled and they are assigned to queue 8.
So revert the adjustment of the MISC IRQ location, to make it be the
last one in IRQ vectors.
Fixes: 937d46ecc5f9 ("net: wangxun: add ethtool_ops for channel number")
Cc: stable@vger.kernel.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://patch.msgid.link/20250701063030.59340-3-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Move the creating of irq_domain for MISC IRQ from .probe to .ndo_open,
and free it in .ndo_stop, to maintain consistency with the queue IRQs.
This it for subsequent adjustments to the IRQ vectors.
Fixes: aefd013624a1 ("net: txgbe: use irq_domain for interrupt controller")
Cc: stable@vger.kernel.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20250701063030.59340-2-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The `tx_may_stop()` logic stops TX queues if free descriptors
(`sq->vq->num_free`) fall below the threshold of (`MAX_SKB_FRAGS` + 2).
If the total ring size (`ring_num`) is not strictly greater than this
value, queues can become persistently stopped or stop after minimal
use, severely degrading performance.
A single sk_buff transmission typically requires descriptors for:
- The virtio_net_hdr (1 descriptor)
- The sk_buff's linear data (head) (1 descriptor)
- Paged fragments (up to MAX_SKB_FRAGS descriptors)
This patch enforces that the TX ring size ('ring_num') must be strictly
greater than (MAX_SKB_FRAGS + 2). This ensures that the ring is
always large enough to hold at least one maximally-fragmented packet
plus at least one additional slot.
Reported-by: Lei Yang <leiyang@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://patch.msgid.link/20250521092236.661410-4-lvivier@redhat.com
Tested-by: Lei Yang <leiyang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Improve consistency by using everywhere it is needed
'MAX_SKB_FRAGS + 2' rather than '2+MAX_SKB_FRAGS' or
'2 + MAX_SKB_FRAGS'.
No functional change.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://patch.msgid.link/20250521092236.661410-3-lvivier@redhat.com
Tested-by: Lei Yang <leiyang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The virtqueue_resize() function was not correctly propagating error codes
from its internal resize helper functions, specifically
virtqueue_resize_packet() and virtqueue_resize_split(). If these helpers
returned an error, but the subsequent call to virtqueue_enable_after_reset()
succeeded, the original error from the resize operation would be masked.
Consequently, virtqueue_resize() could incorrectly report success to its
caller despite an underlying resize failure.
This change restores the original code behavior:
if (vdev->config->enable_vq_after_reset(_vq))
return -EBUSY;
return err;
Fix: commit ad48d53b5b3f ("virtio_ring: separate the logic of reset/enable from virtqueue_resize")
Cc: xuanzhuo@linux.alibaba.com
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://patch.msgid.link/20250521092236.661410-2-lvivier@redhat.com
Tested-by: Lei Yang <leiyang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When calling buf_to_xdp, the len argument is the frame data's length
without virtio header's length (vi->hdr_len). We check that len with
xsk_pool_get_rx_frame_size() + vi->hdr_len
to ensure the provided len does not larger than the allocated chunk
size. The additional vi->hdr_len is because in virtnet_add_recvbuf_xsk,
we use part of XDP_PACKET_HEADROOM for virtio header and ask the vhost
to start placing data from
hard_start + XDP_PACKET_HEADROOM - vi->hdr_len
not
hard_start + XDP_PACKET_HEADROOM
But the first buffer has virtio_header, so the maximum frame's length in
the first buffer can only be
xsk_pool_get_rx_frame_size()
not
xsk_pool_get_rx_frame_size() + vi->hdr_len
like in the current check.
This commit adds an additional argument to buf_to_xdp differentiate
between the first buffer and other ones to correctly calculate the maximum
frame's length.
Cc: stable@vger.kernel.org
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Fixes: a4e7ba702701 ("virtio_net: xsk: rx: support recv small mode")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://patch.msgid.link/20250630151315.86722-2-minhquangbui99@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Replace the current repeated code to check received length in mergeable
mode with the new check_mergeable_len helper.
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://patch.msgid.link/20250630144212.48471-4-minhquangbui99@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The truesize is guaranteed not to exceed PAGE_SIZE in
get_mergeable_buf_len(). It is saved in mergeable context, which is not
changeable by the host side, so the check in receive path is quite
redundant.
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://patch.msgid.link/20250630144212.48471-3-minhquangbui99@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In xdp_linearize_page, when reading the following buffers from the ring,
we forget to check the received length with the true allocate size. This
can lead to an out-of-bound read. This commit adds that missing check.
Cc: <stable@vger.kernel.org>
Fixes: 4941d472bf95 ("virtio-net: do not reset during XDP set")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://patch.msgid.link/20250630144212.48471-2-minhquangbui99@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
udp_v4_early_demux now returns drop reasons as it either returns 0 or
ip_mc_validate_source, which returns itself a drop reason. However its
use was not converted in ip_rcv_finish_core and the drop reason is
ignored, leading to potentially skipping increasing LINUX_MIB_IPRPFILTER
if the drop reason is SKB_DROP_REASON_IP_RPFILTER.
This is a fix and we're not converting udp_v4_early_demux to explicitly
return a drop reason to ease backports; this can be done as a follow-up.
Fixes: d46f827016d8 ("net: ip: make ip_mc_validate_source() return drop reason")
Cc: Menglong Dong <menglong8.dong@gmail.com>
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/20250701074935.144134-1-atenart@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When setting "ethtool -L eth0 combined 1", the number of RX/TX queue is
changed to be 1. RSS is disabled at this moment, and the indices of FDIR
have not be changed in wx_set_rss_queues(). So the combined count still
shows the previous value. This issue was introduced when supporting
FDIR. Fix it for those devices that support FDIR.
Fixes: 34744a7749b3 ("net: txgbe: add FDIR info to ethtool ops")
Cc: stable@vger.kernel.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/A5C8FE56D6C04608+20250701070625.73680-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The link status is latched low so that momentary link drops
can be detected. Always double-reading the status defeats this
design feature. Only double read if link was already down
This prevents unnecessary duplicate readings of the link status.
Fixes: 4f3b20bfbb75 ("amd-xgbe: add support for rx-adaptation")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250701065016.4140707-1-Raju.Rangoju@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Certain classful qdiscs may invoke their classes' dequeue handler on an
enqueue operation. This may unexpectedly empty the child qdisc and thus
make an in-flight class passive via qlen_notify(). Most qdiscs do not
expect such behaviour at this point in time and may re-activate the
class eventually anyways which will lead to a use-after-free.
The referenced fix commit attempted to fix this behavior for the HFSC
case by moving the backlog accounting around, though this turned out to
be incomplete since the parent's parent may run into the issue too.
The following reproducer demonstrates this use-after-free:
tc qdisc add dev lo root handle 1: drr
tc filter add dev lo parent 1: basic classid 1:1
tc class add dev lo parent 1: classid 1:1 drr
tc qdisc add dev lo parent 1:1 handle 2: hfsc def 1
tc class add dev lo parent 2: classid 2:1 hfsc rt m1 8 d 1 m2 0
tc qdisc add dev lo parent 2:1 handle 3: netem
tc qdisc add dev lo parent 3:1 handle 4: blackhole
echo 1 | socat -u STDIN UDP4-DATAGRAM:127.0.0.1:8888
tc class delete dev lo classid 1:1
echo 1 | socat -u STDIN UDP4-DATAGRAM:127.0.0.1:8888
Since backlog accounting issues leading to a use-after-frees on stale
class pointers is a recurring pattern at this point, this patch takes
a different approach. Instead of trying to fix the accounting, the patch
ensures that qdisc_tree_reduce_backlog always calls qlen_notify when
the child qdisc is empty. This solves the problem because deletion of
qdiscs always involves a call to qdisc_reset() and / or
qdisc_purge_queue() which ultimately resets its qlen to 0 thus causing
the following qdisc_tree_reduce_backlog() to report to the parent. Note
that this may call qlen_notify on passive classes multiple times. This
is not a problem after the recent patch series that made all the
classful qdiscs qlen_notify() handlers idempotent.
Fixes: 3f981138109f ("sch_hfsc: Fix qlen accounting bug when using peek in hfsc_enqueue()")
Signed-off-by: Lion Ackermann <nnamrec@gmail.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://patch.msgid.link/d912cbd7-193b-4269-9857-525bee8bbb6a@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
dma_map_XXX() functions return values DMA_MAPPING_ERROR as error values
which is often ~0. The error value should be tested with
dma_mapping_error().
This patch creates a new function in niu_ops to test if the mapping
failed. The test is fixed in niu_rbr_add_page(), added in
niu_start_xmit() and the successfully mapped pages are unmaped upon error.
Fixes: ec2deec1f352 ("niu: Fix to check for dma mapping errors.")
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two bugs in rose_rt_device_down() that can cause
use-after-free:
1. The loop bound `t->count` is modified within the loop, which can
cause the loop to terminate early and miss some entries.
2. When removing an entry from the neighbour array, the subsequent entries
are moved up to fill the gap, but the loop index `i` is still
incremented, causing the next entry to be skipped.
For example, if a node has three neighbours (A, A, B) with count=3 and A
is being removed, the second A is not checked.
i=0: (A, A, B) -> (A, B) with count=2
^ checked
i=1: (A, B) -> (A, B) with count=2
^ checked (B, not A!)
i=2: (doesn't occur because i < count is false)
This leaves the second A in the array with count=2, but the rose_neigh
structure has been freed. Code that accesses these entries assumes that
the first `count` entries are valid pointers, causing a use-after-free
when it accesses the dangling pointer.
Fix both issues by iterating over the array in reverse order with a fixed
loop bound. This ensures that all entries are examined and that the removal
of an entry doesn't affect subsequent iterations.
Reported-by: syzbot+e04e2c007ba2c80476cb@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=e04e2c007ba2c80476cb
Tested-by: syzbot+e04e2c007ba2c80476cb@syzkaller.appspotmail.com
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Kohei Enju <enjuk@amazon.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250629030833.6680-1-enjuk@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The comparison in enic_change_mtu() incorrectly used the current
netdev->mtu instead of the new new_mtu value when warning about
an MTU exceeding the port MTU. This could suppress valid warnings
or issue incorrect ones.
Fix the condition and log to properly reflect the new_mtu.
Fixes: ab123fe071c9 ("enic: handle mtu change for vf properly")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Acked-by: John Daley <johndale@cisco.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250628145612.476096-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update the Clause 37 Auto-Negotiation implementation to properly align
with the PCS hardware specifications:
- Fix incorrect bit settings in Link Status and Link Duplex fields
- Implement missing sequence steps 2 and 7
These changes ensure CL37 auto-negotiation protocol follows the exact
sequence patterns as specified in the hardware databook.
Fixes: 1bf40ada6290 ("amd-xgbe: Add support for clause 37 auto-negotiation")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20250630192636.3838291-1-Raju.Rangoju@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Smatch complains that the error message isn't set in the caller:
lib/test_objagg.c:923 test_hints_case2()
error: uninitialized symbol 'errmsg'.
This static checker warning only showed up after a recent refactoring
but the bug dates back to when the code was originally added. This
likely doesn't affect anything in real life.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/r/202506281403.DsuyHFTZ-lkp@intel.com/
Fixes: 0a020d416d0a ("lib: introduce initial implementation of object aggregation manager")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/8548f423-2e3b-4bb7-b816-5041de2762aa@sabinyo.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
I226 devices advertise support for the PCI-E link L1.2 substate. However,
due to a hardware limitation, the exit latency from this low-power state
is longer than the packet buffer can tolerate under high traffic
conditions. This can lead to packet loss and degraded performance.
To mitigate this, disable the L1.2 substate. The increased power draw
between L1.1 and L1.2 is insignificant.
Fixes: 43546211738e ("igc: Add new device ID's")
Link: https://lore.kernel.org/intel-wired-lan/15248b4f-3271-42dd-8e35-02bfc92b25e1@intel.com
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
With VIRTCHNL2_CAP_MACFILTER enabled, the following warning is generated
on module load:
[ 324.701677] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:578
[ 324.701684] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 1582, name: NetworkManager
[ 324.701689] preempt_count: 201, expected: 0
[ 324.701693] RCU nest depth: 0, expected: 0
[ 324.701697] 2 locks held by NetworkManager/1582:
[ 324.701702] #0: ffffffff9f7be770 (rtnl_mutex){....}-{3:3}, at: rtnl_newlink+0x791/0x21e0
[ 324.701730] #1: ff1100216c380368 (_xmit_ETHER){....}-{2:2}, at: __dev_open+0x3f0/0x870
[ 324.701749] Preemption disabled at:
[ 324.701752] [<ffffffff9cd23b9d>] __dev_open+0x3dd/0x870
[ 324.701765] CPU: 30 UID: 0 PID: 1582 Comm: NetworkManager Not tainted 6.15.0-rc5+ #2 PREEMPT(voluntary)
[ 324.701771] Hardware name: Intel Corporation M50FCP2SBSTD/M50FCP2SBSTD, BIOS SE5C741.86B.01.01.0001.2211140926 11/14/2022
[ 324.701774] Call Trace:
[ 324.701777] <TASK>
[ 324.701779] dump_stack_lvl+0x5d/0x80
[ 324.701788] ? __dev_open+0x3dd/0x870
[ 324.701793] __might_resched.cold+0x1ef/0x23d
<..>
[ 324.701818] __mutex_lock+0x113/0x1b80
<..>
[ 324.701917] idpf_ctlq_clean_sq+0xad/0x4b0 [idpf]
[ 324.701935] ? kasan_save_track+0x14/0x30
[ 324.701941] idpf_mb_clean+0x143/0x380 [idpf]
<..>
[ 324.701991] idpf_send_mb_msg+0x111/0x720 [idpf]
[ 324.702009] idpf_vc_xn_exec+0x4cc/0x990 [idpf]
[ 324.702021] ? rcu_is_watching+0x12/0xc0
[ 324.702035] idpf_add_del_mac_filters+0x3ed/0xb50 [idpf]
<..>
[ 324.702122] __hw_addr_sync_dev+0x1cf/0x300
[ 324.702126] ? find_held_lock+0x32/0x90
[ 324.702134] idpf_set_rx_mode+0x317/0x390 [idpf]
[ 324.702152] __dev_open+0x3f8/0x870
[ 324.702159] ? __pfx___dev_open+0x10/0x10
[ 324.702174] __dev_change_flags+0x443/0x650
<..>
[ 324.702208] netif_change_flags+0x80/0x160
[ 324.702218] do_setlink.isra.0+0x16a0/0x3960
<..>
[ 324.702349] rtnl_newlink+0x12fd/0x21e0
The sequence is as follows:
rtnl_newlink()->
__dev_change_flags()->
__dev_open()->
dev_set_rx_mode() - > # disables BH and grabs "dev->addr_list_lock"
idpf_set_rx_mode() -> # proceed only if VIRTCHNL2_CAP_MACFILTER is ON
__dev_uc_sync() ->
idpf_add_mac_filter ->
idpf_add_del_mac_filters ->
idpf_send_mb_msg() ->
idpf_mb_clean() ->
idpf_ctlq_clean_sq() # mutex_lock(cq_lock)
Fix by converting cq_lock to a spinlock. All operations under the new
lock are safe except freeing the DMA memory, which may use vunmap(). Fix
by requesting a contiguous physical memory for the DMA mapping.
Fixes: a251eee62133 ("idpf: add SRIOV support and other ndo_ops")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Returning -EOPNOTSUPP from function returning u32 is leading to
cast and invalid size value as a result.
-EOPNOTSUPP as a size probably will lead to allocation fail.
Command: ethtool -x eth0
It is visible on all devices that don't have RSS caps set.
[ 136.615917] Call Trace:
[ 136.615921] <TASK>
[ 136.615927] ? __warn+0x89/0x130
[ 136.615942] ? __alloc_frozen_pages_noprof+0x322/0x330
[ 136.615953] ? report_bug+0x164/0x190
[ 136.615968] ? handle_bug+0x58/0x90
[ 136.615979] ? exc_invalid_op+0x17/0x70
[ 136.615987] ? asm_exc_invalid_op+0x1a/0x20
[ 136.616001] ? rss_prepare_get.constprop.0+0xb9/0x170
[ 136.616016] ? __alloc_frozen_pages_noprof+0x322/0x330
[ 136.616028] __alloc_pages_noprof+0xe/0x20
[ 136.616038] ___kmalloc_large_node+0x80/0x110
[ 136.616072] __kmalloc_large_node_noprof+0x1d/0xa0
[ 136.616081] __kmalloc_noprof+0x32c/0x4c0
[ 136.616098] ? rss_prepare_get.constprop.0+0xb9/0x170
[ 136.616105] rss_prepare_get.constprop.0+0xb9/0x170
[ 136.616114] ethnl_default_doit+0x107/0x3d0
[ 136.616131] genl_family_rcv_msg_doit+0x100/0x160
[ 136.616147] genl_rcv_msg+0x1b8/0x2c0
[ 136.616156] ? __pfx_ethnl_default_doit+0x10/0x10
[ 136.616168] ? __pfx_genl_rcv_msg+0x10/0x10
[ 136.616176] netlink_rcv_skb+0x58/0x110
[ 136.616186] genl_rcv+0x28/0x40
[ 136.616195] netlink_unicast+0x19b/0x290
[ 136.616206] netlink_sendmsg+0x222/0x490
[ 136.616215] __sys_sendto+0x1fd/0x210
[ 136.616233] __x64_sys_sendto+0x24/0x30
[ 136.616242] do_syscall_64+0x82/0x160
[ 136.616252] ? __sys_recvmsg+0x83/0xe0
[ 136.616265] ? syscall_exit_to_user_mode+0x10/0x210
[ 136.616275] ? do_syscall_64+0x8e/0x160
[ 136.616282] ? __count_memcg_events+0xa1/0x130
[ 136.616295] ? count_memcg_events.constprop.0+0x1a/0x30
[ 136.616306] ? handle_mm_fault+0xae/0x2d0
[ 136.616319] ? do_user_addr_fault+0x379/0x670
[ 136.616328] ? clear_bhb_loop+0x45/0xa0
[ 136.616340] ? clear_bhb_loop+0x45/0xa0
[ 136.616349] ? clear_bhb_loop+0x45/0xa0
[ 136.616359] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ 136.616369] RIP: 0033:0x7fd30ba7b047
[ 136.616376] Code: 0c 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 80 3d bd d5 0c 00 00 41 89 ca 74 10 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 71 c3 55 48 83 ec 30 44 89 4c 24 2c 4c 89 44
[ 136.616381] RSP: 002b:00007ffde1796d68 EFLAGS: 00000202 ORIG_RAX: 000000000000002c
[ 136.616388] RAX: ffffffffffffffda RBX: 000055d7bd89f2a0 RCX: 00007fd30ba7b047
[ 136.616392] RDX: 0000000000000028 RSI: 000055d7bd89f3b0 RDI: 0000000000000003
[ 136.616396] RBP: 00007ffde1796e10 R08: 00007fd30bb4e200 R09: 000000000000000c
[ 136.616399] R10: 0000000000000000 R11: 0000000000000202 R12: 000055d7bd89f340
[ 136.616403] R13: 000055d7bd89f3b0 R14: 000055d78943f200 R15: 0000000000000000
Fixes: 02cbfba1add5 ("idpf: add ethtool callbacks")
Reviewed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Commit d53320aeef18 ("dt-bindings: net: Rename
renesas,r9a09g057-gbeth.yaml") renames the net devicetree binding
renesas,r9a09g057-gbeth.yaml to renesas,rzv2h-gbeth.yaml, but misses to
adjust the file entry in the RENESAS RZ/V2H(P) DWMAC GBETH GLUE LAYER
DRIVER section in MAINTAINERS.
Adjust the file entry after this file renaming.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@redhat.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20250627134453.51780-1-lukas.bulwahn@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove redundant netif_napi_del() call from disconnect path.
A WARN may be triggered in __netif_napi_del_locked() during USB device
disconnect:
WARNING: CPU: 0 PID: 11 at net/core/dev.c:7417 __netif_napi_del_locked+0x2b4/0x350
This happens because netif_napi_del() is called in the disconnect path while
NAPI is still enabled. However, it is not necessary to call netif_napi_del()
explicitly, since unregister_netdev() will handle NAPI teardown automatically
and safely. Removing the redundant call avoids triggering the warning.
Full trace:
lan78xx 1-1:1.0 enu1: Failed to read register index 0x000000c4. ret = -ENODEV
lan78xx 1-1:1.0 enu1: Failed to set MAC down with error -ENODEV
lan78xx 1-1:1.0 enu1: Link is Down
lan78xx 1-1:1.0 enu1: Failed to read register index 0x00000120. ret = -ENODEV
------------[ cut here ]------------
WARNING: CPU: 0 PID: 11 at net/core/dev.c:7417 __netif_napi_del_locked+0x2b4/0x350
Modules linked in: flexcan can_dev fuse
CPU: 0 UID: 0 PID: 11 Comm: kworker/0:1 Not tainted 6.16.0-rc2-00624-ge926949dab03 #9 PREEMPT
Hardware name: SKOV IMX8MP CPU revC - bd500 (DT)
Workqueue: usb_hub_wq hub_event
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __netif_napi_del_locked+0x2b4/0x350
lr : __netif_napi_del_locked+0x7c/0x350
sp : ffffffc085b673c0
x29: ffffffc085b673c0 x28: ffffff800b7f2000 x27: ffffff800b7f20d8
x26: ffffff80110bcf58 x25: ffffff80110bd978 x24: 1ffffff0022179eb
x23: ffffff80110bc000 x22: ffffff800b7f5000 x21: ffffff80110bc000
x20: ffffff80110bcf38 x19: ffffff80110bcf28 x18: dfffffc000000000
x17: ffffffc081578940 x16: ffffffc08284cee0 x15: 0000000000000028
x14: 0000000000000006 x13: 0000000000040000 x12: ffffffb0022179e8
x11: 1ffffff0022179e7 x10: ffffffb0022179e7 x9 : dfffffc000000000
x8 : 0000004ffdde8619 x7 : ffffff80110bcf3f x6 : 0000000000000001
x5 : ffffff80110bcf38 x4 : ffffff80110bcf38 x3 : 0000000000000000
x2 : 0000000000000000 x1 : 1ffffff0022179e7 x0 : 0000000000000000
Call trace:
__netif_napi_del_locked+0x2b4/0x350 (P)
lan78xx_disconnect+0xf4/0x360
usb_unbind_interface+0x158/0x718
device_remove+0x100/0x150
device_release_driver_internal+0x308/0x478
device_release_driver+0x1c/0x30
bus_remove_device+0x1a8/0x368
device_del+0x2e0/0x7b0
usb_disable_device+0x244/0x540
usb_disconnect+0x220/0x758
hub_event+0x105c/0x35e0
process_one_work+0x760/0x17b0
worker_thread+0x768/0xce8
kthread+0x3bc/0x690
ret_from_fork+0x10/0x20
irq event stamp: 211604
hardirqs last enabled at (211603): [<ffffffc0828cc9ec>] _raw_spin_unlock_irqrestore+0x84/0x98
hardirqs last disabled at (211604): [<ffffffc0828a9a84>] el1_dbg+0x24/0x80
softirqs last enabled at (211296): [<ffffffc080095f10>] handle_softirqs+0x820/0xbc8
softirqs last disabled at (210993): [<ffffffc080010288>] __do_softirq+0x18/0x20
---[ end trace 0000000000000000 ]---
lan78xx 1-1:1.0 enu1: failed to kill vid 0081/0
Fixes: ec4c7e12396b ("lan78xx: Introduce NAPI polling support")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20250627051346.276029-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a occasional problem that ping is failed between AML devices.
That is because the manual enablement of the security Tx path on the
hardware is missing, no matter what its previous state was.
Fixes: 6f8b4c01a8cd ("net: txgbe: Implement PHYLINK for AML 25G/10G devices")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/5BDFB14C57D1C42A+20250626085153.86122-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
I have been working on mlx5 related code for several years,
contributing features, code reviews, and occasional maintainer tasks
when needed. This patch makes my maintainer role official.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://patch.msgid.link/20250627014252.1262592-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
Oleksij Rempel
EricChan
David Howells
Christophe JAILLET
Michal Luczaj
Haoxiang Li
Chen-Yu Tsai
Jiayuan Chen
Ryo Takakura
Kuniyuki Iwashima
Stefano Garzarella
Luo Jie
Jason Xing
Luiz Augusto von Dentz
HarshaVardhana S A
Krzysztof Kozlowski
Jiawen Wu
Laurent Vivier
Bui Quang Minh
Antoine Tenart
Raju Rangoju
Lion Ackermann
Thomas Fourier
Kohei Enju
Alok Tiwari
Dan Carpenter
Vitaly Lifshits
Ahmed Zaki
Michal Swiatkowski
Lukas Bulwahn
Mark Bloch