| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add Adreno SMMU, GPU clock controller, GMU and GPU nodes for the
SC8280XP.
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230614142204.2675653-2-quic_bjorande@quicinc.com
|
|
Some of the regulators must be always-on to ensure correct operation of
the system, e.g. PM8916 L2 for the LPDDR RAM, L5 for most digital I/O
and L7 for the CPU PLL (strictly speaking the CPU PLL might only need
an active-only vote but this is not supported for regulators in
mainline currently).
The RPM firmware seems to enforce that internally, these supplies stay
on even if we vote for them to power off (and there is no other
processor running). This means it's pointless to keep sending
enable/disable requests because they will just be ignored.
Also, drivers are much more likely to get a wrong impression of the
regulator status, because regulator_is_enabled() will return false when
there are no users, even though the regulator is always on.
Describe this properly by marking the regulators as always-on.
The same changes was already made for MSM8916 in commit 8bbd35771f90
("arm64: dts: qcom: msm8916-pm8916: Mark always-on regulators").
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230530-msm8939-regulators-v1-8-a3c3ac833567@gerhold.net
|
|
Right now each MSM8939 device has a huge block of regulator constraints
with allowed voltages for each regulator. For lack of better
documentation these voltages are often copied as-is from the vendor
device tree, without much extra thought.
Unfortunately, the voltages in the vendor device trees are often
misleading or even wrong, e.g. because:
- There is a large voltage range allowed and the actual voltage is
only set somewhere hidden in some messy vendor driver. This is often
the case for pm8916_{l14,l15,l16} because they have a broad range of
1.8-3.3V by default.
- The voltage is actually wrong but thanks to the voltage constraints
in the RPM firmware it still ends up applying the correct voltage.
To have proper regulator constraints it is important to review them in
context of the usage. The current setup in the MSM8939 device trees
makes this quite hard because each device duplicates the standard
voltages for components of the SoC and mixes those with minor
device-specific additions and dummy voltages for completely unused
regulators.
The actual usage of the regulators for the SoC components is in
msm8939-pm8916.dtsi, so it can and should also define the related
voltage constraints. These are not board-specific but defined in the
MSM8939/PM8916 specification. There is no documentation available for
MSM8939 but in practice it's almost identical to MSM8916.
Note that this commit does not make any functional change. All used
regulators still have the same regulator constraints as before. Unused
regulators do not have regulator constraints anymore because most of
these were too broad or even entirely wrong. They should be added back
with proper voltage constraints when there is an actual usage.
The same changes were already made for MSM8916 in commit b0a8f16ae4a0
("arm64: dts: qcom: msm8916: Define regulator constraints next to usage").
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230530-msm8939-regulators-v1-7-a3c3ac833567@gerhold.net
|
|
Add the same comment to msm8939-pm8916.dtsi that was added for the
MSM8916 variant in commit f193264986b5 ("arm64: dts: qcom:
msm8916-pm8916: Clarify purpose").
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230530-msm8939-regulators-v1-6-a3c3ac833567@gerhold.net
|
|
The regulator constraints for the MSM8939 devices were originally taken
from Qualcomm's msm-3.10 vendor device tree (for lack of better
documentation). Unfortunately it turns out that Qualcomm's voltages are
slightly off as well and do not match the voltage constraints applied
by the RPM firmware.
This means that we sometimes request a specific voltage but the RPM
firmware actually applies a much lower or higher voltage. This is
particularly critical for pm8916_l11 which is used as SD card VMMC
regulator: The SD card can choose a voltage from the current range of
1.8 - 2.95V. If it chooses to run at 1.8V we pretend that this is fine
but the RPM firmware will still silently end up configuring 2.95V.
This can be easily reproduced with a multimeter or by checking the
SPMI hardware registers of the regulator.
Apply the same change as for MSM8916 in commit 355750828c55 ("arm64:
dts: qcom: msm8916: Fix regulator constraints") and make the voltages
match the actual "specified range" in the PM8916 Device Specification
which is enforced by the RPM firmware.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230530-msm8939-regulators-v1-5-a3c3ac833567@gerhold.net
|
|
The vendor kernel from Sony does not have regulator-always-on for
pm8916_l6, so we should be able to disable it when setting up the
display properly. Since sony-tulip does not have display set up
currently it should be fine to let the regulator disable until then.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230530-msm8939-regulators-v1-4-a3c3ac833567@gerhold.net
|
|
msm8939-sony-xperia-kanuti-tulip.dts has several regulator voltages
that do not quite seem to match what is used in the vendor kernel.
In particular:
- l10 is fixed at 2.8V [1, 2]
- l11/l12 are 2.95V max [1]
[1]: https://github.com/sonyxperiadev/kernel/blob/aosp/LA.BR.1.3.3_rb2.14/arch/arm/boot/dts/qcom/msm8939-regulator.dtsi
[2]: https://github.com/sonyxperiadev/kernel/blob/aosp/LA.BR.1.3.3_rb2.14/arch/arm/boot/dts/qcom/msm8939-kanuti_tulip.dtsi#L671C1-L673
Fixes: f1134f738fad ("arm64: dts: qcom: Add msm8939 Sony Xperia M4 Aqua")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230530-msm8939-regulators-v1-3-a3c3ac833567@gerhold.net
|
|
Update for recent changes to msm8916.dtsi in commit a5cf21b14666
("arm64: dts: qcom: msm8916: Disable audio codecs by default") and
make lpass_codec disabled by default for devices that are not using
the audio codec functionality inside MSM8939.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230530-msm8939-regulators-v1-2-a3c3ac833567@gerhold.net
|
|
Update for recent changes to pm8916.dtsi in commit 38218822a72f
("arm64: dts: qcom: pm8916: Move default regulator "-supply"s")
and add the now missing pm8916_codec supplies to msm8939-pm8916.dtsi
as well.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230530-msm8939-regulators-v1-1-a3c3ac833567@gerhold.net
|
|
Enable the PMIC GPIO- and RESIN-connected buttons on the board.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230613-topic-rb2_-v1-1-696cd7dbda28@linaro.org
|
|
MSM8916 and MSM8939 are pin-compatible and should have exactly the same
pinctrl definitions. Still, having pinctrl separated to a -pins.dtsi
is not typical anymore for Qualcomm platforms upstream. Since Bjorn
specifically requested having the MSM8939 pinctrl inside msm8939.dtsi
lets move the MSM8916 definitions to msm8916.dtsi as well to have
a consistent location.
While at it sort the nodes and drop unnecessary empty lines.
Note that in almost all cases changes to MSM8916 pinctrl should also be
applied to MSM8939 pinctrl (and vice versa). Right now they are back in
sync again and completely identical.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230529-msm8916-pinctrl-v1-6-11f540b51c93@gerhold.net
|
|
All the pinctrl now uses consistent _default/_sleep suffix so rename
the WCNSS pinctrl to be named consistently.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230529-msm8916-pinctrl-v1-5-11f540b51c93@gerhold.net
|
|
The audio pinctrl in MSM8916/MSM8939 is very similar but still has
subtle differences, e.g. &cdc_pdm_lines_act on MSM8916 vs
&cdc_pdm_lines_default on MSM8939.
Make this consistent and use the chance to cleanup all of the audio
pinctrl: Drop unneeded outer nodes and replace the names taken over
from the vendor kernel with more clear ones that are similar to the
actual pinctrl function.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230529-msm8916-pinctrl-v1-4-11f540b51c93@gerhold.net
|
|
GPIO116 is not connected (NC) on DB410c so there is no need to route
MCLK there. The MSM8916 digital codec receives the MCLK internally
without leaving the SoC through a GPIO.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230529-msm8916-pinctrl-v1-3-11f540b51c93@gerhold.net
|
|
MSM8939 has the SDC pinctrl consolidated in two &sdcN_default and
&sdcN_sleep states, while MSM8916 has all pins separated. Make this
consistent by consolidating them for MSM8916 well.
Use this as a chance to define default pinctrl in the SoC.dtsi and only
let boards that add additional definitions (such as cd-gpios) override it.
For MSM8939 just make the label consistent with the other pinctrl
definitions (they do not have a _state suffix).
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230529-msm8916-pinctrl-v1-2-11f540b51c93@gerhold.net
|
|
The current SD card detect pinctrl setup configures bias-pull-up for
the "default" (active) case and bias-disable for the "sleep" case.
Before commit b5c833b703cc ("mmc: sdhci-msm: Set IO pins in low power
state during suspend") the pull up was permanently active. Since then
it is only active when a valid SD card is inserted.
This does not really make sense: For an active-low CD, the pull up is
needed to pull the GPIO high when the card is not inserted. When the
card gets inserted CD is shorted to ground (low). This means right now
the pull-up is removed exactly when it is needed to detect the next
card insertion. Generally, applying different bias for CD does not
really make sense. It should always stay the same so card removals and
insertions can be detected properly.
The reason why card detection still works fine in practice is that most
boards seem to have external pull up on the CD pin. However, this means
that there is no need to configure an internal pull-up at all and we
can keep bias-disable permanently.
There are also some boards with different CD polarity (acer-a1-724) and
with different GPIO number (huawei-g7). All in all this makes it
obvious that the CD pin is board-specific and the pinctrl for it should
be defined in the board DT.
Move it to the boards that need it and use bias-disable permanently for
the boards that seem to have external pull-up. The vendor device tree
for msm8939-sony-xperia-kanuti-tulip suggests that it needs the
internal pull-up permanently [1] so it gets bias-pull-up to be sure.
[1]: https://github.com/sonyxperiadev/kernel/blob/57b5050e340f40a88e1ddb8d16fd9adb44418923/arch/arm/boot/dts/qcom/msm8939-kanuti_tulip.dtsi#L634-L636
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230529-msm8916-pinctrl-v1-1-11f540b51c93@gerhold.net
|
|
Currently in board files MDSS and HDMI nodes stay apart, because labels
for HDMI nodes do not have the mdss_ prefix. It was found that grouping
all display-related notes is more useful.
To keep all display-related nodes close in the board files, change HDMI
node labels from hdmi_* to mdss_hdmi_*.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531011623.3808538-14-dmitry.baryshkov@linaro.org
|
|
Currently in board files MDSS and DSI nodes stay apart, because labels
for DSI nodes do not have the mdss_ prefix. It was found that grouping
all display-related notes is more useful.
To keep all display-related nodes close in the board files, change DSI
node labels from dsi_* to mdss_dsi_*.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531011623.3808538-13-dmitry.baryshkov@linaro.org
|
|
Currently in board files MDSS and DSI nodes stay apart, because labels
for DSI nodes do not have the mdss_ prefix. It was found that grouping
all display-related notes is more useful.
To keep all display-related nodes close in the board files, change DSI
node labels from dsi_* to mdss_dsi_*.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531011623.3808538-12-dmitry.baryshkov@linaro.org
|
|
Currently in board files MDSS and DSI nodes stay apart, because labels
for DSI nodes do not have the mdss_ prefix. It was found that grouping
all display-related notes is more useful.
To keep all display-related nodes close in the board files, change DSI
node labels from dsi_* to mdss_dsi_*.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531011623.3808538-11-dmitry.baryshkov@linaro.org
|
|
Currently in board files MDSS and DSI nodes stay apart, because labels
for DSI nodes do not have the mdss_ prefix. It was found that grouping
all display-related notes is more useful.
To keep all display-related nodes close in the board files, change DSI
node labels from dsi_* to mdss_dsi_*.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531011623.3808538-10-dmitry.baryshkov@linaro.org
|
|
Currently in board files MDSS and DSI nodes stay apart, because labels
for DSI nodes do not have the mdss_ prefix. It was found that grouping
all display-related notes is more useful.
To keep all display-related nodes close in the board files, change DSI
node labels from dsi_* to mdss_dsi_*.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531011623.3808538-9-dmitry.baryshkov@linaro.org
|
|
Currently in board files MDSS and DSI nodes stay apart, because labels
for DSI nodes do not have the mdss_ prefix. It was found that grouping
all display-related notes is more useful.
To keep all display-related nodes close in the board files, change DSI
node labels from dsi_* to mdss_dsi_*.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531011623.3808538-8-dmitry.baryshkov@linaro.org
|
|
Currently in board files MDSS and DSI nodes stay apart, because labels
for DSI nodes do not have the mdss_ prefix. It was found that grouping
all display-related notes is more useful.
To keep all display-related nodes close in the board files, change DSI
node labels from dsi_* to mdss_dsi_*.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531011623.3808538-7-dmitry.baryshkov@linaro.org
|
|
Currently in board files MDSS and DSI nodes stay apart, because labels
for DSI nodes do not have the mdss_ prefix. It was found that grouping
all display-related notes is more useful.
To keep all display-related nodes close in the board files, change DSI
node labels from dsi_* to mdss_dsi_*.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531011623.3808538-6-dmitry.baryshkov@linaro.org
|
|
The MDP/DPU device is not disabled by default since the commit
0c25dad9f2a7 ("arm64: dts: qcom: sm8250: Don't disable MDP explicitly"),
so there is not point in enabling it in the board DTS file.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531011623.3808538-5-dmitry.baryshkov@linaro.org
|
|
The MDP/DPU device is not disabled by default, so there is not point in
enabling it in the board DTS file.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531011623.3808538-4-dmitry.baryshkov@linaro.org
|
|
The MDP/DPU device is not disabled by default, so there is not point in
enabling it in the board DTS file.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531011623.3808538-3-dmitry.baryshkov@linaro.org
|
|
MDSS and all its subdevices are useless without DPU/MDP, so disabling
MDP doesn't make any sense. Remove explicit disabling of the DPU device.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531011623.3808538-2-dmitry.baryshkov@linaro.org
|
|
Add the initial device tree support for the Reference Design Platform (RDP)
454 based on IPQ9574 family of SoCs. This patch adds support for Console
UART, SPI NOR and SMPA1 regulator node.
Signed-off-by: Poovendhan Selvaraj <quic_poovendh@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531032648.23816-3-quic_poovendh@quicinc.com
|
|
Document AL02-C9 (Reference Design Platform 454) board based on IPQ9574
family of SoCs.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Poovendhan Selvaraj <quic_poovendh@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531032648.23816-2-quic_poovendh@quicinc.com
|
|
Add GPUCC and Adreno SMMU nodes in preparation for adding the GPU
itself.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230531-topic-sm6375_gpusmmu-v1-2-860943894c71@linaro.org
|
|
The USB HC node is missing the interconnect paths, so add them.
Fixes: 7f7e5c1b037f ("arm64: dts: qcom: sm8550: Add USB PHYs and controller nodes")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230601103817.4066446-1-abel.vesa@linaro.org
|
|
Add sdhci node for emmc in qdu1000-idp.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Komal Bajaj <quic_kbajaj@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230601111128.19562-4-quic_kbajaj@quicinc.com
|
|
Add sdhc node for eMMC on QDU1000 and QRU1000 SoCs. Also add
required pins for SDHCI, so that the interface can work reliably.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Komal Bajaj <quic_kbajaj@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230601111128.19562-3-quic_kbajaj@quicinc.com
|
|
The USB HC node is missing the interconnect paths, so add them.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230602062016.1883171-6-abel.vesa@linaro.org
|
|
The USB HCs nodes are missing the interconnect paths, so add them.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230602062016.1883171-5-abel.vesa@linaro.org
|
|
The USB HCs nodes are missing the interconnect paths, so add them.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230602062016.1883171-4-abel.vesa@linaro.org
|
|
Use two interconnect cells in order to optionally support a path tag.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230602062016.1883171-3-abel.vesa@linaro.org
|
|
The USB HCs nodes are missing the interconnect paths, so add them.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230602062016.1883171-2-abel.vesa@linaro.org
|
|
Use two interconnect cells in order to optionally support a path tag.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230602062016.1883171-1-abel.vesa@linaro.org
|
|
The framebuffer configuration for edo pdx203, written in edo dtsi (which
is overwritten in pdx206 dts for its smaller panel) has to use a
1096x2560 configuration as this is what the panel (and framebuffer area)
has been initialized to. Downstream userspace also has access to (and
uses) this 2.5k mode by default, and only switches the panel to 4k when
requested.
This is similar to commit be8de06dc397 ("arm64: dts: qcom:
sm8150-kumano: Panel framebuffer is 2.5k instead of 4k") which fixed the
same for the previous generation Sony platform.
Fixes: 69cdb97ef652 ("arm64: dts: qcom: sm8250: Add support for SONY Xperia 1 II / 5 II (Edo platform)")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230606211418.587676-1-marijn.suijten@somainline.org
|
|
Add the (scarce) idle states for the individual CPUs, as well as the
whole cluster. This enables deeper-than-WFI cpuidle
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230606-topic-qcm2290_idlestates-v2-1-580a5a2d28c9@linaro.org
|
|
Add a compatible for Samsung Galaxy Express SGH-I437.
Signed-off-by: Rudraksha Gupta <guptarud@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230607050025.86636-2-guptarud@gmail.com
|
|
This patch adds thermal zone nodes for the various
sensors present in IPQ9574
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Co-developed-by: Praveenkumar I <quic_ipkumar@quicinc.com>
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/404c88e9746b3f25585aef078861ec2c273232d5.1686125196.git.quic_varada@quicinc.com
|
|
IPQ9574 has a tsens v2.3.1 peripheral which monitors temperatures
around the various subsystems on the die.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Co-developed-by: Praveenkumar I <quic_ipkumar@quicinc.com>
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/00fa16039db78dcb919bd15444bbf86ff3a340d6.1686125196.git.quic_varada@quicinc.com
|
|
According to bindings, thermal zones must have associated trips as well.
Since we currently dont have CPUFreq support and thus no passive cooling
lets start by defining critical trips to protect the devices against
severe overheating.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230607184448.2512179-1-robimarko@gmail.com
|
|
Add opp-peak-kBps to CPU OPPs to allow for CBF scaling, and change the
CBF compatible to reflect the difference between it and the one on
MSM8996.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230527093934.101335-3-y.oudjana@protonmail.com
|
|
Enable the pmi8998 charger and define some basic battery properties.
Signed-off-by: Joel Selvaraj <joelselvaraj.oss@gmail.com>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230524-pmi8998-charger-dts-v2-5-2a5c77d2ff0c@linaro.org
|
|
Enable the PMI8998/smb2 charger, and denote the secondary SMB1355
charger which is used for parallel charging.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230524-pmi8998-charger-dts-v2-4-2a5c77d2ff0c@linaro.org
|
Bjorn Andersson
Stephan Gerhold
Konrad Dybcio
Dmitry Baryshkov
Poovendhan Selvaraj
Abel Vesa
Komal Bajaj
Marijn Suijten
Rudraksha Gupta
Varadarajan Narayanan
Robert Marko
Yassine Oudjana
Joel Selvaraj
Caleb Connolly