From edcbf5137f093b5502f5f6b97cce3cbadbde27aa Mon Sep 17 00:00:00 2001 From: Danielle Ratson Date: Thu, 25 Feb 2021 18:57:19 +0200 Subject: selftests: forwarding: Fix race condition in mirror installation When mirroring to a gretap in hardware the device expects to be programmed with the egress port and all the encapsulating headers. This requires the driver to resolve the path the packet will take in the software data path and program the device accordingly. If the path cannot be resolved (in this case because of an unresolved neighbor), then mirror installation fails until the path is resolved. This results in a race that causes the test to sometimes fail. Fix this by setting the neighbor's state to permanent, so that it is always valid. Fixes: b5b029399fa6d ("selftests: forwarding: mirror_gre_bridge_1d_vlan: Add STP test") Signed-off-by: Danielle Ratson Reviewed-by: Petr Machata Signed-off-by: Ido Schimmel Signed-off-by: Jakub Kicinski --- .../selftests/net/forwarding/mirror_gre_bridge_1d_vlan.sh | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/tools/testing/selftests/net/forwarding/mirror_gre_bridge_1d_vlan.sh b/tools/testing/selftests/net/forwarding/mirror_gre_bridge_1d_vlan.sh index 197e769c2ed1..f8cda822c1ce 100755 --- a/tools/testing/selftests/net/forwarding/mirror_gre_bridge_1d_vlan.sh +++ b/tools/testing/selftests/net/forwarding/mirror_gre_bridge_1d_vlan.sh @@ -86,11 +86,20 @@ test_ip6gretap() test_gretap_stp() { + # Sometimes after mirror installation, the neighbor's state is not valid. + # The reason is that there is no SW datapath activity related to the + # neighbor for the remote GRE address. Therefore whether the corresponding + # neighbor will be valid is a matter of luck, and the test is thus racy. + # Set the neighbor's state to permanent, so it would be always valid. + ip neigh replace 192.0.2.130 lladdr $(mac_get $h3) \ + nud permanent dev br2 full_test_span_gre_stp gt4 $swp3.555 "mirror to gretap" } test_ip6gretap_stp() { + ip neigh replace 2001:db8:2::2 lladdr $(mac_get $h3) \ + nud permanent dev br2 full_test_span_gre_stp gt6 $swp3.555 "mirror to ip6gretap" } -- cgit v1.2.3-59-g8ed1b From ae9b24ddb69b4e31cda1b5e267a5a08a1db11717 Mon Sep 17 00:00:00 2001 From: Danielle Ratson Date: Thu, 25 Feb 2021 18:57:20 +0200 Subject: mlxsw: spectrum_ethtool: Add an external speed to PTYS register Currently, only external bits are added to the PTYS register, whereas there is one external bit that is wrongly marked as internal, and so was recently removed from the register. Add that bit to the PTYS register again, as this bit is no longer internal. Its removal resulted in '100000baseLR4_ER4/Full' link mode no longer being supported, causing a regression on some setups. Fixes: 5bf01b571cf4 ("mlxsw: spectrum_ethtool: Remove internal speeds from PTYS register") Signed-off-by: Danielle Ratson Reported-by: Eddie Shklaer Tested-by: Eddie Shklaer Reviewed-by: Jiri Pirko Signed-off-by: Ido Schimmel Signed-off-by: Jakub Kicinski --- drivers/net/ethernet/mellanox/mlxsw/reg.h | 1 + drivers/net/ethernet/mellanox/mlxsw/spectrum_ethtool.c | 5 +++++ drivers/net/ethernet/mellanox/mlxsw/switchx2.c | 3 ++- 3 files changed, 8 insertions(+), 1 deletion(-) diff --git a/drivers/net/ethernet/mellanox/mlxsw/reg.h b/drivers/net/ethernet/mellanox/mlxsw/reg.h index 16e2df6ef2f4..c4adc7f740d3 100644 --- a/drivers/net/ethernet/mellanox/mlxsw/reg.h +++ b/drivers/net/ethernet/mellanox/mlxsw/reg.h @@ -4430,6 +4430,7 @@ MLXSW_ITEM32(reg, ptys, ext_eth_proto_cap, 0x08, 0, 32); #define MLXSW_REG_PTYS_ETH_SPEED_100GBASE_CR4 BIT(20) #define MLXSW_REG_PTYS_ETH_SPEED_100GBASE_SR4 BIT(21) #define MLXSW_REG_PTYS_ETH_SPEED_100GBASE_KR4 BIT(22) +#define MLXSW_REG_PTYS_ETH_SPEED_100GBASE_LR4_ER4 BIT(23) #define MLXSW_REG_PTYS_ETH_SPEED_25GBASE_CR BIT(27) #define MLXSW_REG_PTYS_ETH_SPEED_25GBASE_KR BIT(28) #define MLXSW_REG_PTYS_ETH_SPEED_25GBASE_SR BIT(29) diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum_ethtool.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum_ethtool.c index bd7f873f6290..0bd64169bf81 100644 --- a/drivers/net/ethernet/mellanox/mlxsw/spectrum_ethtool.c +++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum_ethtool.c @@ -1169,6 +1169,11 @@ static const struct mlxsw_sp1_port_link_mode mlxsw_sp1_port_link_mode[] = { .mask_ethtool = ETHTOOL_LINK_MODE_100000baseKR4_Full_BIT, .speed = SPEED_100000, }, + { + .mask = MLXSW_REG_PTYS_ETH_SPEED_100GBASE_LR4_ER4, + .mask_ethtool = ETHTOOL_LINK_MODE_100000baseLR4_ER4_Full_BIT, + .speed = SPEED_100000, + }, }; #define MLXSW_SP1_PORT_LINK_MODE_LEN ARRAY_SIZE(mlxsw_sp1_port_link_mode) diff --git a/drivers/net/ethernet/mellanox/mlxsw/switchx2.c b/drivers/net/ethernet/mellanox/mlxsw/switchx2.c index 40e2e79d4517..131b2a53d261 100644 --- a/drivers/net/ethernet/mellanox/mlxsw/switchx2.c +++ b/drivers/net/ethernet/mellanox/mlxsw/switchx2.c @@ -613,7 +613,8 @@ static const struct mlxsw_sx_port_link_mode mlxsw_sx_port_link_mode[] = { { .mask = MLXSW_REG_PTYS_ETH_SPEED_100GBASE_CR4 | MLXSW_REG_PTYS_ETH_SPEED_100GBASE_SR4 | - MLXSW_REG_PTYS_ETH_SPEED_100GBASE_KR4, + MLXSW_REG_PTYS_ETH_SPEED_100GBASE_KR4 | + MLXSW_REG_PTYS_ETH_SPEED_100GBASE_LR4_ER4, .speed = 100000, }, }; -- cgit v1.2.3-59-g8ed1b From dc860b88ce0a7ed9a048d5042cbb175daf60b657 Mon Sep 17 00:00:00 2001 From: Ido Schimmel Date: Thu, 25 Feb 2021 18:57:21 +0200 Subject: mlxsw: spectrum_router: Ignore routes using a deleted nexthop object Routes are currently processed from a workqueue whereas nexthop objects are processed in system call context. This can result in the driver not finding a suitable nexthop group for a route and issuing a warning [1]. Fix this by ignoring such routes earlier in the process. The subsequent deletion notification will be ignored as well. [1] WARNING: CPU: 2 PID: 7754 at drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:4853 mlxsw_sp_router_fib_event_work+0x1112/0x1e00 [mlxsw_spectrum] [...] CPU: 2 PID: 7754 Comm: kworker/u8:0 Not tainted 5.11.0-rc6-cq-20210207-1 #16 Hardware name: Mellanox Technologies Ltd. MSN2100/SA001390, BIOS 5.6.5 05/24/2018 Workqueue: mlxsw_core_ordered mlxsw_sp_router_fib_event_work [mlxsw_spectrum] RIP: 0010:mlxsw_sp_router_fib_event_work+0x1112/0x1e00 [mlxsw_spectrum] Fixes: cdd6cfc54c64 ("mlxsw: spectrum_router: Allow programming routes with nexthop objects") Signed-off-by: Ido Schimmel Reported-by: Alex Veber Tested-by: Alex Veber Reviewed-by: Petr Machata Reviewed-by: Jiri Pirko Signed-off-by: Jakub Kicinski --- drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c index 9ce90841f92d..eda99d82766a 100644 --- a/drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c +++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c @@ -5951,6 +5951,10 @@ mlxsw_sp_router_fib4_replace(struct mlxsw_sp *mlxsw_sp, if (mlxsw_sp->router->aborted) return 0; + if (fen_info->fi->nh && + !mlxsw_sp_nexthop_obj_group_lookup(mlxsw_sp, fen_info->fi->nh->id)) + return 0; + fib_node = mlxsw_sp_fib_node_get(mlxsw_sp, fen_info->tb_id, &fen_info->dst, sizeof(fen_info->dst), fen_info->dst_len, @@ -6601,6 +6605,9 @@ static int mlxsw_sp_router_fib6_replace(struct mlxsw_sp *mlxsw_sp, if (mlxsw_sp_fib6_rt_should_ignore(rt)) return 0; + if (rt->nh && !mlxsw_sp_nexthop_obj_group_lookup(mlxsw_sp, rt->nh->id)) + return 0; + fib_node = mlxsw_sp_fib_node_get(mlxsw_sp, rt->fib6_table->tb6_id, &rt->fib6_dst.addr, sizeof(rt->fib6_dst.addr), -- cgit v1.2.3-59-g8ed1b