From 74ac28f16486aca295ae27aafc8d7e088464b772 Mon Sep 17 00:00:00 2001 From: Dan Murphy Date: Thu, 14 May 2020 10:59:05 -0500 Subject: dt-bindings: dp83867: Convert DP83867 to yaml Convert the dp83867 binding to yaml. Signed-off-by: Dan Murphy Signed-off-by: David S. Miller --- .../devicetree/bindings/net/ti,dp83867.yaml | 127 +++++++++++++++++++++ 1 file changed, 127 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/ti,dp83867.yaml (limited to 'Documentation/devicetree/bindings/net/ti,dp83867.yaml') diff --git a/Documentation/devicetree/bindings/net/ti,dp83867.yaml b/Documentation/devicetree/bindings/net/ti,dp83867.yaml new file mode 100644 index 000000000000..554dcd7a40a9 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ti,dp83867.yaml @@ -0,0 +1,127 @@ +# SPDX-License-Identifier: (GPL-2.0+ OR BSD-2-Clause) +# Copyright (C) 2019 Texas Instruments Incorporated +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/net/ti,dp83867.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: TI DP83867 ethernet PHY + +allOf: + - $ref: "ethernet-controller.yaml#" + +maintainers: + - Dan Murphy + +description: | + The DP83867 device is a robust, low power, fully featured Physical Layer + transceiver with integrated PMD sublayers to support 10BASE-Te, 100BASE-TX + and 1000BASE-T Ethernet protocols. + + The DP83867 is designed for easy implementation of 10/100/1000 Mbps Ethernet + LANs. It interfaces directly to twisted pair media via an external + transformer. This device interfaces directly to the MAC layer through the + IEEE 802.3 Standard Media Independent Interface (MII), the IEEE 802.3 Gigabit + Media Independent Interface (GMII) or Reduced GMII (RGMII). + + Specifications about the charger can be found at: + https://www.ti.com/lit/gpn/dp83867ir + +properties: + reg: + maxItems: 1 + + ti,min-output-impedance: + type: boolean + description: | + MAC Interface Impedance control to set the programmable output impedance + to a minimum value (35 ohms). + + ti,max-output-impedance: + type: boolean + description: | + MAC Interface Impedance control to set the programmable output impedance + to a maximum value (70 ohms). + Note: ti,min-output-impedance and ti,max-output-impedance are mutually + exclusive. When both properties are present ti,max-output-impedance + takes precedence. + + tx-fifo-depth: + $ref: /schemas/types.yaml#definitions/uint32 + description: | + Transmitt FIFO depth see dt-bindings/net/ti-dp83867.h for values + + rx-fifo-depth: + $ref: /schemas/types.yaml#definitions/uint32 + description: | + Receive FIFO depth see dt-bindings/net/ti-dp83867.h for values + + ti,clk-output-sel: + $ref: /schemas/types.yaml#definitions/uint32 + description: | + Muxing option for CLK_OUT pin. See dt-bindings/net/ti-dp83867.h + for applicable values. The CLK_OUT pin can also be disabled by this + property. When omitted, the PHY's default will be left as is. + + ti,rx-internal-delay: + $ref: /schemas/types.yaml#definitions/uint32 + description: | + RGMII Receive Clock Delay - see dt-bindings/net/ti-dp83867.h + for applicable values. Required only if interface type is + PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_RXID. + + ti,tx-internal-delay: + $ref: /schemas/types.yaml#definitions/uint32 + description: | + RGMII Transmit Clock Delay - see dt-bindings/net/ti-dp83867.h + for applicable values. Required only if interface type is + PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_TXID. + + Note: If the interface type is PHY_INTERFACE_MODE_RGMII the TX/RX clock + delays will be left at their default values, as set by the PHY's pin + strapping. The default strapping will use a delay of 2.00 ns. Thus + PHY_INTERFACE_MODE_RGMII, by default, does not behave as RGMII with no + internal delay, but as PHY_INTERFACE_MODE_RGMII_ID. The device tree + should use "rgmii-id" if internal delays are desired as this may be + changed in future to cause "rgmii" mode to disable delays. + + ti,dp83867-rxctrl-strap-quirk: + type: boolean + description: | + This denotes the fact that the board has RX_DV/RX_CTRL pin strapped in + mode 1 or 2. To ensure PHY operation, there are specific actions that + software needs to take when this pin is strapped in these modes. + See data manual for details. + + ti,sgmii-ref-clock-output-enable: + type: boolean + description: | + This denotes which SGMII configuration is used (4 or 6-wire modes). + Some MACs work with differential SGMII clock. See data manual for details. + + ti,fifo-depth: + deprecated: true + $ref: /schemas/types.yaml#definitions/uint32 + description: | + Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h for applicable + values. + +required: + - reg + +examples: + - | + #include + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + ethphy0: ethernet-phy@0 { + reg = <0>; + tx-fifo-depth = ; + rx-fifo-depth = ; + ti,max-output-impedance; + ti,clk-output-sel = ; + ti,rx-internal-delay = ; + ti,tx-internal-delay = ; + }; + }; -- cgit v1.2.3-59-g8ed1b