From 40cc72e2b51f61956f965510ceba35bddb0c373f Mon Sep 17 00:00:00 2001 From: Kishon Vijay Abraham I Date: Mon, 27 Mar 2017 15:15:09 +0530 Subject: dt-bindings: PCI: dra7xx: Add DT bindings for PCI dra7xx EP mode Add device tree binding documentation for PCI dra7xx EP mode. Acked-by: Rob Herring Signed-off-by: Kishon Vijay Abraham I Signed-off-by: Bjorn Helgaas --- Documentation/devicetree/bindings/pci/ti-pci.txt | 37 +++++++++++++++++++----- 1 file changed, 30 insertions(+), 7 deletions(-) (limited to 'Documentation/devicetree/bindings/pci/ti-pci.txt') diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt index 60e25161f351..60c3cccefabc 100644 --- a/Documentation/devicetree/bindings/pci/ti-pci.txt +++ b/Documentation/devicetree/bindings/pci/ti-pci.txt @@ -1,17 +1,22 @@ TI PCI Controllers PCIe Designware Controller - - compatible: Should be "ti,dra7-pcie"" - - reg : Two register ranges as listed in the reg-names property - - reg-names : The first entry must be "ti-conf" for the TI specific registers - The second entry must be "rc-dbics" for the designware pcie - registers - The third entry must be "config" for the PCIe configuration space + - compatible: Should be "ti,dra7-pcie" for RC + Should be "ti,dra7-pcie-ep" for EP - phys : list of PHY specifiers (used by generic PHY framework) - phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the number of PHYs as specified in *phys* property. - ti,hwmods : Name of the hwmod associated to the pcie, "pcie", where is the instance number of the pcie from the HW spec. + - num-lanes as specified in ../designware-pcie.txt + +HOST MODE +========= + - reg : Two register ranges as listed in the reg-names property + - reg-names : The first entry must be "ti-conf" for the TI specific registers + The second entry must be "rc-dbics" for the DesignWare PCIe + registers + The third entry must be "config" for the PCIe configuration space - interrupts : Two interrupt entries must be specified. The first one is for main interrupt line and the second for MSI interrupt line. - #address-cells, @@ -19,13 +24,31 @@ PCIe Designware Controller #interrupt-cells, device_type, ranges, - num-lanes, interrupt-map-mask, interrupt-map : as specified in ../designware-pcie.txt +DEVICE MODE +=========== + - reg : Four register ranges as listed in the reg-names property + - reg-names : "ti-conf" for the TI specific registers + "ep_dbics" for the standard configuration registers as + they are locally accessed within the DIF CS space + "ep_dbics2" for the standard configuration registers as + they are locally accessed within the DIF CS2 space + "addr_space" used to map remote RC address space + - interrupts : one interrupt entries must be specified for main interrupt. + - num-ib-windows : number of inbound address translation windows + - num-ob-windows : number of outbound address translation windows + Optional Property: - gpios : Should be added if a gpio line is required to drive PERST# line +NOTE: Two DT nodes may be added for each PCI controller; one for host +mode and another for device mode. So in order for PCI to +work in host mode, EP mode DT node should be disabled and in order to PCI to +work in EP mode, host mode DT node should be disabled. Host mode and EP +mode are mutually exclusive. + Example: axi { compatible = "simple-bus"; -- cgit v1.2.3-59-g8ed1b