From f53a2ade0bb9f2a81f473e6469155172a96b7c38 Mon Sep 17 00:00:00 2001 From: Alan Cox Date: Fri, 9 Oct 2009 12:56:41 +0100 Subject: tty: esp: remove broken driver The ESP driver has been marked broken for years. It's an old ISA device that clearly nobody cares about any more. Remove it Signed-off-by: Alan Cox Signed-off-by: Greg Kroah-Hartman --- drivers/char/Kconfig | 13 - drivers/char/Makefile | 1 - drivers/char/esp.c | 2533 ------------------------------------------------- 3 files changed, 2547 deletions(-) delete mode 100644 drivers/char/esp.c (limited to 'drivers') diff --git a/drivers/char/Kconfig b/drivers/char/Kconfig index 6aad99ec4e0f..6f31c9472100 100644 --- a/drivers/char/Kconfig +++ b/drivers/char/Kconfig @@ -201,19 +201,6 @@ config DIGIEPCA To compile this driver as a module, choose M here: the module will be called epca. -config ESPSERIAL - tristate "Hayes ESP serial port support" - depends on SERIAL_NONSTANDARD && ISA && ISA_DMA_API && BROKEN - help - This is a driver which supports Hayes ESP serial ports. Both single - port cards and multiport cards are supported. Make sure to read - . - - To compile this driver as a module, choose M here: the - module will be called esp. - - If unsure, say N. - config MOXA_INTELLIO tristate "Moxa Intellio support" depends on SERIAL_NONSTANDARD && (ISA || EISA || PCI) diff --git a/drivers/char/Makefile b/drivers/char/Makefile index 19a79dd79eee..f957edf7e45d 100644 --- a/drivers/char/Makefile +++ b/drivers/char/Makefile @@ -18,7 +18,6 @@ obj-$(CONFIG_CONSOLE_TRANSLATIONS) += consolemap.o consolemap_deftbl.o obj-$(CONFIG_HW_CONSOLE) += vt.o defkeymap.o obj-$(CONFIG_AUDIT) += tty_audit.o obj-$(CONFIG_MAGIC_SYSRQ) += sysrq.o -obj-$(CONFIG_ESPSERIAL) += esp.o obj-$(CONFIG_MVME147_SCC) += generic_serial.o vme_scc.o obj-$(CONFIG_MVME162_SCC) += generic_serial.o vme_scc.o obj-$(CONFIG_BVME6000_SCC) += generic_serial.o vme_scc.o diff --git a/drivers/char/esp.c b/drivers/char/esp.c deleted file mode 100644 index b19d43cd9542..000000000000 --- a/drivers/char/esp.c +++ /dev/null @@ -1,2533 +0,0 @@ -/* - * esp.c - driver for Hayes ESP serial cards - * - * --- Notices from serial.c, upon which this driver is based --- - * - * Copyright (C) 1991, 1992 Linus Torvalds - * - * Extensively rewritten by Theodore Ts'o, 8/16/92 -- 9/14/92. Now - * much more extensible to support other serial cards based on the - * 16450/16550A UART's. Added support for the AST FourPort and the - * Accent Async board. - * - * set_serial_info fixed to set the flags, custom divisor, and uart - * type fields. Fix suggested by Michael K. Johnson 12/12/92. - * - * 11/95: TIOCMIWAIT, TIOCGICOUNT by Angelo Haritsis - * - * 03/96: Modularised by Angelo Haritsis - * - * rs_set_termios fixed to look also for changes of the input - * flags INPCK, BRKINT, PARMRK, IGNPAR and IGNBRK. - * Bernd Anhäupl 05/17/96. - * - * --- End of notices from serial.c --- - * - * Support for the ESP serial card by Andrew J. Robinson - * (Card detection routine taken from a patch - * by Dennis J. Boylan). Patches to allow use with 2.1.x contributed - * by Chris Faylor. - * - * Most recent changes: (Andrew J. Robinson) - * Support for PIO mode. This allows the driver to work properly with - * multiport cards. - * - * Arnaldo Carvalho de Melo - - * several cleanups, use module_init/module_exit, etc - * - * This module exports the following rs232 io functions: - * - * int espserial_init(void); - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include - -#include -#include -#include - -#include - -#define NR_PORTS 64 /* maximum number of ports */ -#define NR_PRIMARY 8 /* maximum number of primary ports */ -#define REGION_SIZE 8 /* size of io region to request */ - -/* The following variables can be set by giving module options */ -static int irq[NR_PRIMARY]; /* IRQ for each base port */ -static unsigned int divisor[NR_PRIMARY]; /* custom divisor for each port */ -static unsigned int dma = ESP_DMA_CHANNEL; /* DMA channel */ -static unsigned int rx_trigger = ESP_RX_TRIGGER; -static unsigned int tx_trigger = ESP_TX_TRIGGER; -static unsigned int flow_off = ESP_FLOW_OFF; -static unsigned int flow_on = ESP_FLOW_ON; -static unsigned int rx_timeout = ESP_RX_TMOUT; -static unsigned int pio_threshold = ESP_PIO_THRESHOLD; - -MODULE_LICENSE("GPL"); - -module_param_array(irq, int, NULL, 0); -module_param_array(divisor, uint, NULL, 0); -module_param(dma, uint, 0); -module_param(rx_trigger, uint, 0); -module_param(tx_trigger, uint, 0); -module_param(flow_off, uint, 0); -module_param(flow_on, uint, 0); -module_param(rx_timeout, uint, 0); -module_param(pio_threshold, uint, 0); - -/* END */ - -static char *dma_buffer; -static int dma_bytes; -static struct esp_pio_buffer *free_pio_buf; - -#define DMA_BUFFER_SZ 1024 - -#define WAKEUP_CHARS 1024 - -static char serial_name[] __initdata = "ESP serial driver"; -static char serial_version[] __initdata = "2.2"; - -static struct tty_driver *esp_driver; - -/* - * Serial driver configuration section. Here are the various options: - * - * SERIAL_PARANOIA_CHECK - * Check the magic number for the esp_structure where - * ever possible. - */ - -#undef SERIAL_PARANOIA_CHECK -#define SERIAL_DO_RESTART - -#undef SERIAL_DEBUG_INTR -#undef SERIAL_DEBUG_OPEN -#undef SERIAL_DEBUG_FLOW - -#if defined(MODULE) && defined(SERIAL_DEBUG_MCOUNT) -#define DBG_CNT(s) printk(KERN_DEBUG "(%s): [%x] refc=%d, serc=%d, ttyc=%d -> %s\n", \ - tty->name, info->port.flags, \ - serial_driver.refcount, \ - info->port.count, tty->count, s) -#else -#define DBG_CNT(s) -#endif - -static struct esp_struct *ports; - -static void change_speed(struct esp_struct *info); -static void rs_wait_until_sent(struct tty_struct *, int); - -/* - * The ESP card has a clock rate of 14.7456 MHz (that is, 2**ESPC_SCALE - * times the normal 1.8432 Mhz clock of most serial boards). - */ -#define BASE_BAUD ((1843200 / 16) * (1 << ESPC_SCALE)) - -/* Standard COM flags (except for COM4, because of the 8514 problem) */ -#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST) - -static inline int serial_paranoia_check(struct esp_struct *info, - char *name, const char *routine) -{ -#ifdef SERIAL_PARANOIA_CHECK - static const char badmagic[] = KERN_WARNING - "Warning: bad magic number for serial struct (%s) in %s\n"; - static const char badinfo[] = KERN_WARNING - "Warning: null esp_struct for (%s) in %s\n"; - - if (!info) { - printk(badinfo, name, routine); - return 1; - } - if (info->magic != ESP_MAGIC) { - printk(badmagic, name, routine); - return 1; - } -#endif - return 0; -} - -static inline unsigned int serial_in(struct esp_struct *info, int offset) -{ - return inb(info->io_port + offset); -} - -static inline void serial_out(struct esp_struct *info, int offset, - unsigned char value) -{ - outb(value, info->io_port+offset); -} - -/* - * ------------------------------------------------------------ - * rs_stop() and rs_start() - * - * This routines are called before setting or resetting tty->stopped. - * They enable or disable transmitter interrupts, as necessary. - * ------------------------------------------------------------ - */ -static void rs_stop(struct tty_struct *tty) -{ - struct esp_struct *info = tty->driver_data; - unsigned long flags; - - if (serial_paranoia_check(info, tty->name, "rs_stop")) - return; - - spin_lock_irqsave(&info->lock, flags); - if (info->IER & UART_IER_THRI) { - info->IER &= ~UART_IER_THRI; - serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK); - serial_out(info, UART_ESI_CMD2, info->IER); - } - spin_unlock_irqrestore(&info->lock, flags); -} - -static void rs_start(struct tty_struct *tty) -{ - struct esp_struct *info = tty->driver_data; - unsigned long flags; - - if (serial_paranoia_check(info, tty->name, "rs_start")) - return; - - spin_lock_irqsave(&info->lock, flags); - if (info->xmit_cnt && info->xmit_buf && !(info->IER & UART_IER_THRI)) { - info->IER |= UART_IER_THRI; - serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK); - serial_out(info, UART_ESI_CMD2, info->IER); - } - spin_unlock_irqrestore(&info->lock, flags); -} - -/* - * ---------------------------------------------------------------------- - * - * Here starts the interrupt handling routines. All of the following - * subroutines are declared as inline and are folded into - * rs_interrupt(). They were separated out for readability's sake. - * - * Note: rs_interrupt() is a "fast" interrupt, which means that it - * runs with interrupts turned off. People who may want to modify - * rs_interrupt() should try to keep the interrupt handler as fast as - * possible. After you are done making modifications, it is not a bad - * idea to do: - * - * gcc -S -DKERNEL -Wall -Wstrict-prototypes -O6 -fomit-frame-pointer serial.c - * - * and look at the resulting assemble code in serial.s. - * - * - Ted Ts'o (tytso@mit.edu), 7-Mar-93 - * ----------------------------------------------------------------------- - */ - -static DEFINE_SPINLOCK(pio_lock); - -static inline struct esp_pio_buffer *get_pio_buffer(void) -{ - struct esp_pio_buffer *buf; - unsigned long flags; - - spin_lock_irqsave(&pio_lock, flags); - if (free_pio_buf) { - buf = free_pio_buf; - free_pio_buf = buf->next; - } else { - buf = kmalloc(sizeof(struct esp_pio_buffer), GFP_ATOMIC); - } - spin_unlock_irqrestore(&pio_lock, flags); - return buf; -} - -static inline void release_pio_buffer(struct esp_pio_buffer *buf) -{ - unsigned long flags; - spin_lock_irqsave(&pio_lock, flags); - buf->next = free_pio_buf; - free_pio_buf = buf; - spin_unlock_irqrestore(&pio_lock, flags); -} - -static inline void receive_chars_pio(struct esp_struct *info, int num_bytes) -{ - struct tty_struct *tty = info->port.tty; - int i; - struct esp_pio_buffer *pio_buf; - struct esp_pio_buffer *err_buf; - unsigned char status_mask; - - pio_buf = get_pio_buffer(); - - if (!pio_buf) - return; - - err_buf = get_pio_buffer(); - - if (!err_buf) { - release_pio_buffer(pio_buf); - return; - } - - status_mask = (info->read_status_mask >> 2) & 0x07; - - for (i = 0; i < num_bytes - 1; i += 2) { - *((unsigned short *)(pio_buf->data + i)) = - inw(info->io_port + UART_ESI_RX); - err_buf->data[i] = serial_in(info, UART_ESI_RWS); - err_buf->data[i + 1] = (err_buf->data[i] >> 3) & status_mask; - err_buf->data[i] &= status_mask; - } - - if (num_bytes & 0x0001) { - pio_buf->data[num_bytes - 1] = serial_in(info, UART_ESI_RX); - err_buf->data[num_bytes - 1] = - (serial_in(info, UART_ESI_RWS) >> 3) & status_mask; - } - - /* make sure everything is still ok since interrupts were enabled */ - tty = info->port.tty; - - if (!tty) { - release_pio_buffer(pio_buf); - release_pio_buffer(err_buf); - info->stat_flags &= ~ESP_STAT_RX_TIMEOUT; - return; - } - - status_mask = (info->ignore_status_mask >> 2) & 0x07; - - for (i = 0; i < num_bytes; i++) { - if (!(err_buf->data[i] & status_mask)) { - int flag = 0; - - if (err_buf->data[i] & 0x04) { - flag = TTY_BREAK; - if (info->port.flags & ASYNC_SAK) - do_SAK(tty); - } else if (err_buf->data[i] & 0x02) - flag = TTY_FRAME; - else if (err_buf->data[i] & 0x01) - flag = TTY_PARITY; - tty_insert_flip_char(tty, pio_buf->data[i], flag); - } - } - - tty_schedule_flip(tty); - - info->stat_flags &= ~ESP_STAT_RX_TIMEOUT; - release_pio_buffer(pio_buf); - release_pio_buffer(err_buf); -} - -static void program_isa_dma(int dma, int dir, unsigned long addr, int len) -{ - unsigned long flags; - - flags = claim_dma_lock(); - disable_dma(dma); - clear_dma_ff(dma); - set_dma_mode(dma, dir); - set_dma_addr(dma, addr); - set_dma_count(dma, len); - enable_dma(dma); - release_dma_lock(flags); -} - -static void receive_chars_dma(struct esp_struct *info, int num_bytes) -{ - info->stat_flags &= ~ESP_STAT_RX_TIMEOUT; - dma_bytes = num_bytes; - info->stat_flags |= ESP_STAT_DMA_RX; - - program_isa_dma(dma, DMA_MODE_READ, isa_virt_to_bus(dma_buffer), - dma_bytes); - serial_out(info, UART_ESI_CMD1, ESI_START_DMA_RX); -} - -static inline void receive_chars_dma_done(struct esp_struct *info, - int status) -{ - struct tty_struct *tty = info->port.tty; - int num_bytes; - unsigned long flags; - - flags = claim_dma_lock(); - disable_dma(dma); - clear_dma_ff(dma); - - info->stat_flags &= ~ESP_STAT_DMA_RX; - num_bytes = dma_bytes - get_dma_residue(dma); - release_dma_lock(flags); - - info->icount.rx += num_bytes; - - if (num_bytes > 0) { - tty_insert_flip_string(tty, dma_buffer, num_bytes - 1); - - status &= (0x1c & info->read_status_mask); - - /* Is the status significant or do we throw the last byte ? */ - if (!(status & info->ignore_status_mask)) { - int statflag = 0; - - if (status & 0x10) { - statflag = TTY_BREAK; - (info->icount.brk)++; - if (info->port.flags & ASYNC_SAK) - do_SAK(tty); - } else if (status & 0x08) { - statflag = TTY_FRAME; - info->icount.frame++; - } else if (status & 0x04) { - statflag = TTY_PARITY; - info->icount.parity++; - } - tty_insert_flip_char(tty, dma_buffer[num_bytes - 1], - statflag); - } - tty_schedule_flip(tty); - } - - if (dma_bytes != num_bytes) { - num_bytes = dma_bytes - num_bytes; - dma_bytes = 0; - receive_chars_dma(info, num_bytes); - } else - dma_bytes = 0; -} - -/* Caller must hold info->lock */ - -static inline void transmit_chars_pio(struct esp_struct *info, - int space_avail) -{ - int i; - struct esp_pio_buffer *pio_buf; - - pio_buf = get_pio_buffer(); - - if (!pio_buf) - return; - - while (space_avail && info->xmit_cnt) { - if (info->xmit_tail + space_avail <= ESP_XMIT_SIZE) { - memcpy(pio_buf->data, - &(info->xmit_buf[info->xmit_tail]), - space_avail); - } else { - i = ESP_XMIT_SIZE - info->xmit_tail; - memcpy(pio_buf->data, - &(info->xmit_buf[info->xmit_tail]), i); - memcpy(&(pio_buf->data[i]), info->xmit_buf, - space_avail - i); - } - - info->xmit_cnt -= space_avail; - info->xmit_tail = (info->xmit_tail + space_avail) & - (ESP_XMIT_SIZE - 1); - - for (i = 0; i < space_avail - 1; i += 2) { - outw(*((unsigned short *)(pio_buf->data + i)), - info->io_port + UART_ESI_TX); - } - - if (space_avail & 0x0001) - serial_out(info, UART_ESI_TX, - pio_buf->data[space_avail - 1]); - - if (info->xmit_cnt) { - serial_out(info, UART_ESI_CMD1, ESI_NO_COMMAND); - serial_out(info, UART_ESI_CMD1, ESI_GET_TX_AVAIL); - space_avail = serial_in(info, UART_ESI_STAT1) << 8; - space_avail |= serial_in(info, UART_ESI_STAT2); - - if (space_avail > info->xmit_cnt) - space_avail = info->xmit_cnt; - } - } - - if (info->xmit_cnt < WAKEUP_CHARS) { - if (info->port.tty) - tty_wakeup(info->port.tty); - -#ifdef SERIAL_DEBUG_INTR - printk("THRE..."); -#endif - - if (info->xmit_cnt <= 0) { - info->IER &= ~UART_IER_THRI; - serial_out(info, UART_ESI_CMD1, - ESI_SET_SRV_MASK); - serial_out(info, UART_ESI_CMD2, info->IER); - } - } - - release_pio_buffer(pio_buf); -} - -/* Caller must hold info->lock */ -static inline void transmit_chars_dma(struct esp_struct *info, int num_bytes) -{ - dma_bytes = num_bytes; - - if (info->xmit_tail + dma_bytes <= ESP_XMIT_SIZE) { - memcpy(dma_buffer, &(info->xmit_buf[info->xmit_tail]), - dma_bytes); - } else { - int i = ESP_XMIT_SIZE - info->xmit_tail; - memcpy(dma_buffer, &(info->xmit_buf[info->xmit_tail]), - i); - memcpy(&(dma_buffer[i]), info->xmit_buf, dma_bytes - i); - } - - info->xmit_cnt -= dma_bytes; - info->xmit_tail = (info->xmit_tail + dma_bytes) & (ESP_XMIT_SIZE - 1); - - if (info->xmit_cnt < WAKEUP_CHARS) { - if (info->port.tty) - tty_wakeup(info->port.tty); - -#ifdef SERIAL_DEBUG_INTR - printk("THRE..."); -#endif - - if (info->xmit_cnt <= 0) { - info->IER &= ~UART_IER_THRI; - serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK); - serial_out(info, UART_ESI_CMD2, info->IER); - } - } - - info->stat_flags |= ESP_STAT_DMA_TX; - - program_isa_dma(dma, DMA_MODE_WRITE, isa_virt_to_bus(dma_buffer), - dma_bytes); - serial_out(info, UART_ESI_CMD1, ESI_START_DMA_TX); -} - -static inline void transmit_chars_dma_done(struct esp_struct *info) -{ - int num_bytes; - unsigned long flags; - - flags = claim_dma_lock(); - disable_dma(dma); - clear_dma_ff(dma); - - num_bytes = dma_bytes - get_dma_residue(dma); - info->icount.tx += dma_bytes; - release_dma_lock(flags); - - if (dma_bytes != num_bytes) { - dma_bytes -= num_bytes; - memmove(dma_buffer, dma_buffer + num_bytes, dma_bytes); - - program_isa_dma(dma, DMA_MODE_WRITE, - isa_virt_to_bus(dma_buffer), dma_bytes); - - serial_out(info, UART_ESI_CMD1, ESI_START_DMA_TX); - } else { - dma_bytes = 0; - info->stat_flags &= ~ESP_STAT_DMA_TX; - } -} - -static void check_modem_status(struct esp_struct *info) -{ - int status; - - serial_out(info, UART_ESI_CMD1, ESI_GET_UART_STAT); - status = serial_in(info, UART_ESI_STAT2); - - if (status & UART_MSR_ANY_DELTA) { - /* update input line counters */ - if (status & UART_MSR_TERI) - info->icount.rng++; - if (status & UART_MSR_DDSR) - info->icount.dsr++; - if (status & UART_MSR_DDCD) - info->icount.dcd++; - if (status & UART_MSR_DCTS) - info->icount.cts++; - wake_up_interruptible(&info->port.delta_msr_wait); - } - - if ((info->port.flags & ASYNC_CHECK_CD) && (status & UART_MSR_DDCD)) { -#if (defined(SERIAL_DEBUG_OPEN) || defined(SERIAL_DEBUG_INTR)) - printk("ttys%d CD now %s...", info->line, - (status & UART_MSR_DCD) ? "on" : "off"); -#endif - if (status & UART_MSR_DCD) - wake_up_interruptible(&info->port.open_wait); - else { -#ifdef SERIAL_DEBUG_OPEN - printk("scheduling hangup..."); -#endif - tty_hangup(info->port.tty); - } - } -} - -/* - * This is the serial driver's interrupt routine - */ -static irqreturn_t rs_interrupt_single(int irq, void *dev_id) -{ - struct esp_struct *info; - unsigned err_status; - unsigned int scratch; - -#ifdef SERIAL_DEBUG_INTR - printk("rs_interrupt_single(%d)...", irq); -#endif - info = (struct esp_struct *)dev_id; - err_status = 0; - scratch = serial_in(info, UART_ESI_SID); - - spin_lock(&info->lock); - - if (!info->port.tty) { - spin_unlock(&info->lock); - return IRQ_NONE; - } - - if (scratch & 0x04) { /* error */ - serial_out(info, UART_ESI_CMD1, ESI_GET_ERR_STAT); - err_status = serial_in(info, UART_ESI_STAT1); - serial_in(info, UART_ESI_STAT2); - - if (err_status & 0x01) - info->stat_flags |= ESP_STAT_RX_TIMEOUT; - - if (err_status & 0x20) /* UART status */ - check_modem_status(info); - - if (err_status & 0x80) /* Start break */ - wake_up_interruptible(&info->break_wait); - } - - if ((scratch & 0x88) || /* DMA completed or timed out */ - (err_status & 0x1c) /* receive error */) { - if (info->stat_flags & ESP_STAT_DMA_RX) - receive_chars_dma_done(info, err_status); - else if (info->stat_flags & ESP_STAT_DMA_TX) - transmit_chars_dma_done(info); - } - - if (!(info->stat_flags & (ESP_STAT_DMA_RX | ESP_STAT_DMA_TX)) && - ((scratch & 0x01) || (info->stat_flags & ESP_STAT_RX_TIMEOUT)) && - (info->IER & UART_IER_RDI)) { - int num_bytes; - - serial_out(info, UART_ESI_CMD1, ESI_NO_COMMAND); - serial_out(info, UART_ESI_CMD1, ESI_GET_RX_AVAIL); - num_bytes = serial_in(info, UART_ESI_STAT1) << 8; - num_bytes |= serial_in(info, UART_ESI_STAT2); - - num_bytes = tty_buffer_request_room(info->port.tty, num_bytes); - - if (num_bytes) { - if (dma_bytes || - (info->stat_flags & ESP_STAT_USE_PIO) || - (num_bytes <= info->config.pio_threshold)) - receive_chars_pio(info, num_bytes); - else - receive_chars_dma(info, num_bytes); - } - } - - if (!(info->stat_flags & (ESP_STAT_DMA_RX | ESP_STAT_DMA_TX)) && - (scratch & 0x02) && (info->IER & UART_IER_THRI)) { - if ((info->xmit_cnt <= 0) || info->port.tty->stopped) { - info->IER &= ~UART_IER_THRI; - serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK); - serial_out(info, UART_ESI_CMD2, info->IER); - } else { - int num_bytes; - - serial_out(info, UART_ESI_CMD1, ESI_NO_COMMAND); - serial_out(info, UART_ESI_CMD1, ESI_GET_TX_AVAIL); - num_bytes = serial_in(info, UART_ESI_STAT1) << 8; - num_bytes |= serial_in(info, UART_ESI_STAT2); - - if (num_bytes > info->xmit_cnt) - num_bytes = info->xmit_cnt; - - if (num_bytes) { - if (dma_bytes || - (info->stat_flags & ESP_STAT_USE_PIO) || - (num_bytes <= info->config.pio_threshold)) - transmit_chars_pio(info, num_bytes); - else - transmit_chars_dma(info, num_bytes); - } - } - } - - info->last_active = jiffies; - -#ifdef SERIAL_DEBUG_INTR - printk("end.\n"); -#endif - spin_unlock(&info->lock); - return IRQ_HANDLED; -} - -/* - * ------------------------------------------------------------------- - * Here ends the serial interrupt routines. - * ------------------------------------------------------------------- - */ - -/* - * --------------------------------------------------------------- - * Low level utility subroutines for the serial driver: routines to - * figure out the appropriate timeout for an interrupt chain, routines - * to initialize and startup a serial port, and routines to shutdown a - * serial port. Useful stuff like that. - * - * Caller should hold lock - * --------------------------------------------------------------- - */ - -static void esp_basic_init(struct esp_struct *info) -{ - /* put ESPC in enhanced mode */ - serial_out(info, UART_ESI_CMD1, ESI_SET_MODE); - - if (info->stat_flags & ESP_STAT_NEVER_DMA) - serial_out(info, UART_ESI_CMD2, 0x01); - else - serial_out(info, UART_ESI_CMD2, 0x31); - - /* disable interrupts for now */ - serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK); - serial_out(info, UART_ESI_CMD2, 0x00); - - /* set interrupt and DMA channel */ - serial_out(info, UART_ESI_CMD1, ESI_SET_IRQ); - - if (info->stat_flags & ESP_STAT_NEVER_DMA) - serial_out(info, UART_ESI_CMD2, 0x01); - else - serial_out(info, UART_ESI_CMD2, (dma << 4) | 0x01); - - serial_out(info, UART_ESI_CMD1, ESI_SET_ENH_IRQ); - - if (info->line % 8) /* secondary port */ - serial_out(info, UART_ESI_CMD2, 0x0d); /* shared */ - else if (info->irq == 9) - serial_out(info, UART_ESI_CMD2, 0x02); - else - serial_out(info, UART_ESI_CMD2, info->irq); - - /* set error status mask (check this) */ - serial_out(info, UART_ESI_CMD1, ESI_SET_ERR_MASK); - - if (info->stat_flags & ESP_STAT_NEVER_DMA) - serial_out(info, UART_ESI_CMD2, 0xa1); - else - serial_out(info, UART_ESI_CMD2, 0xbd); - - serial_out(info, UART_ESI_CMD2, 0x00); - - /* set DMA timeout */ - serial_out(info, UART_ESI_CMD1, ESI_SET_DMA_TMOUT); - serial_out(info, UART_ESI_CMD2, 0xff); - - /* set FIFO trigger levels */ - serial_out(info, UART_ESI_CMD1, ESI_SET_TRIGGER); - serial_out(info, UART_ESI_CMD2, info->config.rx_trigger >> 8); - serial_out(info, UART_ESI_CMD2, info->config.rx_trigger); - serial_out(info, UART_ESI_CMD2, info->config.tx_trigger >> 8); - serial_out(info, UART_ESI_CMD2, info->config.tx_trigger); - - /* Set clock scaling and wait states */ - serial_out(info, UART_ESI_CMD1, ESI_SET_PRESCALAR); - serial_out(info, UART_ESI_CMD2, 0x04 | ESPC_SCALE); - - /* set reinterrupt pacing */ - serial_out(info, UART_ESI_CMD1, ESI_SET_REINTR); - serial_out(info, UART_ESI_CMD2, 0xff); -} - -static int startup(struct esp_struct *info) -{ - unsigned long flags; - int retval = 0; - unsigned int num_chars; - - spin_lock_irqsave(&info->lock, flags); - - if (info->port.flags & ASYNC_INITIALIZED) - goto out; - - if (!info->xmit_buf) { - info->xmit_buf = (unsigned char *)get_zeroed_page(GFP_ATOMIC); - retval = -ENOMEM; - if (!info->xmit_buf) - goto out; - } - -#ifdef SERIAL_DEBUG_OPEN - printk(KERN_DEBUG "starting up ttys%d (irq %d)...", - info->line, info->irq); -#endif - - /* Flush the RX buffer. Using the ESI flush command may cause */ - /* wild interrupts, so read all the data instead. */ - - serial_out(info, UART_ESI_CMD1, ESI_NO_COMMAND); - serial_out(info, UART_ESI_CMD1, ESI_GET_RX_AVAIL); - num_chars = serial_in(info, UART_ESI_STAT1) << 8; - num_chars |= serial_in(info, UART_ESI_STAT2); - - while (num_chars > 1) { - inw(info->io_port + UART_ESI_RX); - num_chars -= 2; - } - - if (num_chars) - serial_in(info, UART_ESI_RX); - - /* set receive character timeout */ - serial_out(info, UART_ESI_CMD1, ESI_SET_RX_TIMEOUT); - serial_out(info, UART_ESI_CMD2, info->config.rx_timeout); - - /* clear all flags except the "never DMA" flag */ - info->stat_flags &= ESP_STAT_NEVER_DMA; - - if (info->stat_flags & ESP_STAT_NEVER_DMA) - info->stat_flags |= ESP_STAT_USE_PIO; - - spin_unlock_irqrestore(&info->lock, flags); - - /* - * Allocate the IRQ - */ - - retval = request_irq(info->irq, rs_interrupt_single, IRQF_SHARED, - "esp serial", info); - - if (retval) { - if (capable(CAP_SYS_ADMIN)) { - if (info->port.tty) - set_bit(TTY_IO_ERROR, - &info->port.tty->flags); - retval = 0; - } - goto out_unlocked; - } - - if (!(info->stat_flags & ESP_STAT_USE_PIO) && !dma_buffer) { - dma_buffer = (char *)__get_dma_pages( - GFP_KERNEL, get_order(DMA_BUFFER_SZ)); - - /* use PIO mode if DMA buf/chan cannot be allocated */ - if (!dma_buffer) - info->stat_flags |= ESP_STAT_USE_PIO; - else if (request_dma(dma, "esp serial")) { - free_pages((unsigned long)dma_buffer, - get_order(DMA_BUFFER_SZ)); - dma_buffer = NULL; - info->stat_flags |= ESP_STAT_USE_PIO; - } - - } - - info->MCR = UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2; - - spin_lock_irqsave(&info->lock, flags); - serial_out(info, UART_ESI_CMD1, ESI_WRITE_UART); - serial_out(info, UART_ESI_CMD2, UART_MCR); - serial_out(info, UART_ESI_CMD2, info->MCR); - - /* - * Finally, enable interrupts - */ - /* info->IER = UART_IER_MSI | UART_IER_RLSI | UART_IER_RDI; */ - info->IER = UART_IER_RLSI | UART_IER_RDI | UART_IER_DMA_TMOUT | - UART_IER_DMA_TC; - serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK); - serial_out(info, UART_ESI_CMD2, info->IER); - - if (info->port.tty) - clear_bit(TTY_IO_ERROR, &info->port.tty->flags); - info->xmit_cnt = info->xmit_head = info->xmit_tail = 0; - spin_unlock_irqrestore(&info->lock, flags); - - /* - * Set up the tty->alt_speed kludge - */ - if (info->port.tty) { - if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI) - info->port.tty->alt_speed = 57600; - if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI) - info->port.tty->alt_speed = 115200; - if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI) - info->port.tty->alt_speed = 230400; - if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP) - info->port.tty->alt_speed = 460800; - } - - /* - * set the speed of the serial port - */ - change_speed(info); - info->port.flags |= ASYNC_INITIALIZED; - return 0; - -out: - spin_unlock_irqrestore(&info->lock, flags); -out_unlocked: - return retval; -} - -/* - * This routine will shutdown a serial port; interrupts are disabled, and - * DTR is dropped if the hangup on close termio flag is on. - */ -static void shutdown(struct esp_struct *info) -{ - unsigned long flags, f; - - if (!(info->port.flags & ASYNC_INITIALIZED)) - return; - -#ifdef SERIAL_DEBUG_OPEN - printk("Shutting down serial port %d (irq %d)....", info->line, - info->irq); -#endif - - spin_lock_irqsave(&info->lock, flags); - /* - * clear delta_msr_wait queue to avoid mem leaks: we may free the irq - * here so the queue might never be waken up - */ - wake_up_interruptible(&info->port.delta_msr_wait); - wake_up_interruptible(&info->break_wait); - - /* stop a DMA transfer on the port being closed */ - /* DMA lock is higher priority always */ - if (info->stat_flags & (ESP_STAT_DMA_RX | ESP_STAT_DMA_TX)) { - f = claim_dma_lock(); - disable_dma(dma); - clear_dma_ff(dma); - release_dma_lock(f); - - dma_bytes = 0; - } - - /* - * Free the IRQ - */ - free_irq(info->irq, info); - - if (dma_buffer) { - struct esp_struct *current_port = ports; - - while (current_port) { - if ((current_port != info) && - (current_port->port.flags & ASYNC_INITIALIZED)) - break; - - current_port = current_port->next_port; - } - - if (!current_port) { - free_dma(dma); - free_pages((unsigned long)dma_buffer, - get_order(DMA_BUFFER_SZ)); - dma_buffer = NULL; - } - } - - if (info->xmit_buf) { - free_page((unsigned long) info->xmit_buf); - info->xmit_buf = NULL; - } - - info->IER = 0; - serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK); - serial_out(info, UART_ESI_CMD2, 0x00); - - if (!info->port.tty || (info->port.tty->termios->c_cflag & HUPCL)) - info->MCR &= ~(UART_MCR_DTR|UART_MCR_RTS); - - info->MCR &= ~UART_MCR_OUT2; - serial_out(info, UART_ESI_CMD1, ESI_WRITE_UART); - serial_out(info, UART_ESI_CMD2, UART_MCR); - serial_out(info, UART_ESI_CMD2, info->MCR); - - if (info->port.tty) - set_bit(TTY_IO_ERROR, &info->port.tty->flags); - - info->port.flags &= ~ASYNC_INITIALIZED; - spin_unlock_irqrestore(&info->lock, flags); -} - -/* - * This routine is called to set the UART divisor registers to match - * the specified baud rate for a serial port. - */ -static void change_speed(struct esp_struct *info) -{ - unsigned short port; - int quot = 0; - unsigned cflag, cval; - int baud, bits; - unsigned char flow1 = 0, flow2 = 0; - unsigned long flags; - - if (!info->port.tty || !info->port.tty->termios) - return; - cflag = info->port.tty->termios->c_cflag; - port = info->io_port; - - /* byte size and parity */ - switch (cflag & CSIZE) { - case CS5: cval = 0x00; bits = 7; break; - case CS6: cval = 0x01; bits = 8; break; - case CS7: cval = 0x02; bits = 9; break; - case CS8: cval = 0x03; bits = 10; break; - default: cval = 0x00; bits = 7; break; - } - if (cflag & CSTOPB) { - cval |= 0x04; - bits++; - } - if (cflag & PARENB) { - cval |= UART_LCR_PARITY; - bits++; - } - if (!(cflag & PARODD)) - cval |= UART_LCR_EPAR; -#ifdef CMSPAR - if (cflag & CMSPAR) - cval |= UART_LCR_SPAR; -#endif - baud = tty_get_baud_rate(info->port.tty); - if (baud == 38400 && - ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST)) - quot = info->custom_divisor; - else { - if (baud == 134) /* Special case since 134 is really 134.5 */ - quot = (2*BASE_BAUD / 269); - else if (baud) - quot = BASE_BAUD / baud; - } - /* If the quotient is ever zero, default to 9600 bps */ - if (!quot) - quot = BASE_BAUD / 9600; - - if (baud) { - /* Actual rate */ - baud = BASE_BAUD/quot; - tty_encode_baud_rate(info->port.tty, baud, baud); - } - info->timeout = ((1024 * HZ * bits * quot) / BASE_BAUD) + (HZ / 50); - - /* CTS flow control flag and modem status interrupts */ - /* info->IER &= ~UART_IER_MSI; */ - if (cflag & CRTSCTS) { - info->port.flags |= ASYNC_CTS_FLOW; - /* info->IER |= UART_IER_MSI; */ - flow1 = 0x04; - flow2 = 0x10; - } else - info->port.flags &= ~ASYNC_CTS_FLOW; - if (cflag & CLOCAL) - info->port.flags &= ~ASYNC_CHECK_CD; - else - info->port.flags |= ASYNC_CHECK_CD; - - /* - * Set up parity check flag - */ - info->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; - if (I_INPCK(info->port.tty)) - info->read_status_mask |= UART_LSR_FE | UART_LSR_PE; - if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty)) - info->read_status_mask |= UART_LSR_BI; - - info->ignore_status_mask = 0; -#if 0 - /* This should be safe, but for some broken bits of hardware... */ - if (I_IGNPAR(info->port.tty)) { - info->ignore_status_mask |= UART_LSR_PE | UART_LSR_FE; - info->read_status_mask |= UART_LSR_PE | UART_LSR_FE; - } -#endif - if (I_IGNBRK(info->port.tty)) { - info->ignore_status_mask |= UART_LSR_BI; - info->read_status_mask |= UART_LSR_BI; - /* - * If we're ignore parity and break indicators, ignore - * overruns too. (For real raw support). - */ - if (I_IGNPAR(info->port.tty)) { - info->ignore_status_mask |= UART_LSR_OE | \ - UART_LSR_PE | UART_LSR_FE; - info->read_status_mask |= UART_LSR_OE | \ - UART_LSR_PE | UART_LSR_FE; - } - } - - if (I_IXOFF(info->port.tty)) - flow1 |= 0x81; - - spin_lock_irqsave(&info->lock, flags); - /* set baud */ - serial_out(info, UART_ESI_CMD1, ESI_SET_BAUD); - serial_out(info, UART_ESI_CMD2, quot >> 8); - serial_out(info, UART_ESI_CMD2, quot & 0xff); - - /* set data bits, parity, etc. */ - serial_out(info, UART_ESI_CMD1, ESI_WRITE_UART); - serial_out(info, UART_ESI_CMD2, UART_LCR); - serial_out(info, UART_ESI_CMD2, cval); - - /* Enable flow control */ - serial_out(info, UART_ESI_CMD1, ESI_SET_FLOW_CNTL); - serial_out(info, UART_ESI_CMD2, flow1); - serial_out(info, UART_ESI_CMD2, flow2); - - /* set flow control characters (XON/XOFF only) */ - if (I_IXOFF(info->port.tty)) { - serial_out(info, UART_ESI_CMD1, ESI_SET_FLOW_CHARS); - serial_out(info, UART_ESI_CMD2, START_CHAR(info->port.tty)); - serial_out(info, UART_ESI_CMD2, STOP_CHAR(info->port.tty)); - serial_out(info, UART_ESI_CMD2, 0x10); - serial_out(info, UART_ESI_CMD2, 0x21); - switch (cflag & CSIZE) { - case CS5: - serial_out(info, UART_ESI_CMD2, 0x1f); - break; - case CS6: - serial_out(info, UART_ESI_CMD2, 0x3f); - break; - case CS7: - case CS8: - serial_out(info, UART_ESI_CMD2, 0x7f); - break; - default: - serial_out(info, UART_ESI_CMD2, 0xff); - break; - } - } - - /* Set high/low water */ - serial_out(info, UART_ESI_CMD1, ESI_SET_FLOW_LVL); - serial_out(info, UART_ESI_CMD2, info->config.flow_off >> 8); - serial_out(info, UART_ESI_CMD2, info->config.flow_off); - serial_out(info, UART_ESI_CMD2, info->config.flow_on >> 8); - serial_out(info, UART_ESI_CMD2, info->config.flow_on); - - spin_unlock_irqrestore(&info->lock, flags); -} - -static int rs_put_char(struct tty_struct *tty, unsigned char ch) -{ - struct esp_struct *info = tty->driver_data; - unsigned long flags; - int ret = 0; - - if (serial_paranoia_check(info, tty->name, "rs_put_char")) - return 0; - - if (!info->xmit_buf) - return 0; - - spin_lock_irqsave(&info->lock, flags); - if (info->xmit_cnt < ESP_XMIT_SIZE - 1) { - info->xmit_buf[info->xmit_head++] = ch; - info->xmit_head &= ESP_XMIT_SIZE-1; - info->xmit_cnt++; - ret = 1; - } - spin_unlock_irqrestore(&info->lock, flags); - return ret; -} - -static void rs_flush_chars(struct tty_struct *tty) -{ - struct esp_struct *info = tty->driver_data; - unsigned long flags; - - if (serial_paranoia_check(info, tty->name, "rs_flush_chars")) - return; - - spin_lock_irqsave(&info->lock, flags); - - if (info->xmit_cnt <= 0 || tty->stopped || !info->xmit_buf) - goto out; - - if (!(info->IER & UART_IER_THRI)) { - info->IER |= UART_IER_THRI; - serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK); - serial_out(info, UART_ESI_CMD2, info->IER); - } -out: - spin_unlock_irqrestore(&info->lock, flags); -} - -static int rs_write(struct tty_struct *tty, - const unsigned char *buf, int count) -{ - int c, t, ret = 0; - struct esp_struct *info = tty->driver_data; - unsigned long flags; - - if (serial_paranoia_check(info, tty->name, "rs_write")) - return 0; - - if (!info->xmit_buf) - return 0; - - while (1) { - /* Thanks to R. Wolff for suggesting how to do this with */ - /* interrupts enabled */ - - c = count; - t = ESP_XMIT_SIZE - info->xmit_cnt - 1; - - if (t < c) - c = t; - - t = ESP_XMIT_SIZE - info->xmit_head; - - if (t < c) - c = t; - - if (c <= 0) - break; - - memcpy(info->xmit_buf + info->xmit_head, buf, c); - - info->xmit_head = (info->xmit_head + c) & (ESP_XMIT_SIZE-1); - info->xmit_cnt += c; - buf += c; - count -= c; - ret += c; - } - - spin_lock_irqsave(&info->lock, flags); - - if (info->xmit_cnt && !tty->stopped && !(info->IER & UART_IER_THRI)) { - info->IER |= UART_IER_THRI; - serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK); - serial_out(info, UART_ESI_CMD2, info->IER); - } - - spin_unlock_irqrestore(&info->lock, flags); - return ret; -} - -static int rs_write_room(struct tty_struct *tty) -{ - struct esp_struct *info = tty->driver_data; - int ret; - unsigned long flags; - - if (serial_paranoia_check(info, tty->name, "rs_write_room")) - return 0; - - spin_lock_irqsave(&info->lock, flags); - - ret = ESP_XMIT_SIZE - info->xmit_cnt - 1; - if (ret < 0) - ret = 0; - spin_unlock_irqrestore(&info->lock, flags); - return ret; -} - -static int rs_chars_in_buffer(struct tty_struct *tty) -{ - struct esp_struct *info = tty->driver_data; - - if (serial_paranoia_check(info, tty->name, "rs_chars_in_buffer")) - return 0; - return info->xmit_cnt; -} - -static void rs_flush_buffer(struct tty_struct *tty) -{ - struct esp_struct *info = tty->driver_data; - unsigned long flags; - - if (serial_paranoia_check(info, tty->name, "rs_flush_buffer")) - return; - spin_lock_irqsave(&info->lock, flags); - info->xmit_cnt = info->xmit_head = info->xmit_tail = 0; - spin_unlock_irqrestore(&info->lock, flags); - tty_wakeup(tty); -} - -/* - * ------------------------------------------------------------ - * rs_throttle() - * - * This routine is called by the upper-layer tty layer to signal that - * incoming characters should be throttled. - * ------------------------------------------------------------ - */ -static void rs_throttle(struct tty_struct *tty) -{ - struct esp_struct *info = tty->driver_data; - unsigned long flags; -#ifdef SERIAL_DEBUG_THROTTLE - char buf[64]; - - printk("throttle %s: %d....\n", tty_name(tty, buf), - tty_chars_in_buffer(tty)); -#endif - - if (serial_paranoia_check(info, tty->name, "rs_throttle")) - return; - - spin_lock_irqsave(&info->lock, flags); - info->IER &= ~UART_IER_RDI; - serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK); - serial_out(info, UART_ESI_CMD2, info->IER); - serial_out(info, UART_ESI_CMD1, ESI_SET_RX_TIMEOUT); - serial_out(info, UART_ESI_CMD2, 0x00); - spin_unlock_irqrestore(&info->lock, flags); -} - -static void rs_unthrottle(struct tty_struct *tty) -{ - struct esp_struct *info = tty->driver_data; - unsigned long flags; -#ifdef SERIAL_DEBUG_THROTTLE - char buf[64]; - - printk(KERN_DEBUG "unthrottle %s: %d....\n", tty_name(tty, buf), - tty_chars_in_buffer(tty)); -#endif - - if (serial_paranoia_check(info, tty->name, "rs_unthrottle")) - return; - - spin_lock_irqsave(&info->lock, flags); - info->IER |= UART_IER_RDI; - serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK); - serial_out(info, UART_ESI_CMD2, info->IER); - serial_out(info, UART_ESI_CMD1, ESI_SET_RX_TIMEOUT); - serial_out(info, UART_ESI_CMD2, info->config.rx_timeout); - spin_unlock_irqrestore(&info->lock, flags); -} - -/* - * ------------------------------------------------------------ - * rs_ioctl() and friends - * ------------------------------------------------------------ - */ - -static int get_serial_info(struct esp_struct *info, - struct serial_struct __user *retinfo) -{ - struct serial_struct tmp; - - lock_kernel(); - memset(&tmp, 0, sizeof(tmp)); - tmp.type = PORT_16550A; - tmp.line = info->line; - tmp.port = info->io_port; - tmp.irq = info->irq; - tmp.flags = info->port.flags; - tmp.xmit_fifo_size = 1024; - tmp.baud_base = BASE_BAUD; - tmp.close_delay = info->close_delay; - tmp.closing_wait = info->closing_wait; - tmp.custom_divisor = info->custom_divisor; - tmp.hub6 = 0; - unlock_kernel(); - if (copy_to_user(retinfo, &tmp, sizeof(*retinfo))) - return -EFAULT; - return 0; -} - -static int get_esp_config(struct esp_struct *info, - struct hayes_esp_config __user *retinfo) -{ - struct hayes_esp_config tmp; - - if (!retinfo) - return -EFAULT; - - memset(&tmp, 0, sizeof(tmp)); - lock_kernel(); - tmp.rx_timeout = info->config.rx_timeout; - tmp.rx_trigger = info->config.rx_trigger; - tmp.tx_trigger = info->config.tx_trigger; - tmp.flow_off = info->config.flow_off; - tmp.flow_on = info->config.flow_on; - tmp.pio_threshold = info->config.pio_threshold; - tmp.dma_channel = (info->stat_flags & ESP_STAT_NEVER_DMA ? 0 : dma); - unlock_kernel(); - - return copy_to_user(retinfo, &tmp, sizeof(*retinfo)) ? -EFAULT : 0; -} - -static int set_serial_info(struct esp_struct *info, - struct serial_struct __user *new_info) -{ - struct serial_struct new_serial; - struct esp_struct old_info; - unsigned int change_irq; - int retval = 0; - struct esp_struct *current_async; - - if (copy_from_user(&new_serial, new_info, sizeof(new_serial))) - return -EFAULT; - old_info = *info; - - if ((new_serial.type != PORT_16550A) || - (new_serial.hub6) || - (info->io_port != new_serial.port) || - (new_serial.baud_base != BASE_BAUD) || - (new_serial.irq > 15) || - (new_serial.irq < 2) || - (new_serial.irq == 6) || - (new_serial.irq == 8) || - (new_serial.irq == 13)) - return -EINVAL; - - change_irq = new_serial.irq != info->irq; - - if (change_irq && (info->line % 8)) - return -EINVAL; - - if (!capable(CAP_SYS_ADMIN)) { - if (change_irq || - (new_serial.close_delay != info->close_delay) || - ((new_serial.flags & ~ASYNC_USR_MASK) != - (info->port.flags & ~ASYNC_USR_MASK))) - return -EPERM; - info->port.flags = ((info->port.flags & ~ASYNC_USR_MASK) | - (new_serial.flags & ASYNC_USR_MASK)); - info->custom_divisor = new_serial.custom_divisor; - } else { - if (new_serial.irq == 2) - new_serial.irq = 9; - - if (change_irq) { - current_async = ports; - - while (current_async) { - if ((current_async->line >= info->line) && - (current_async->line < (info->line + 8))) { - if (current_async == info) { - if (current_async->port.count > 1) - return -EBUSY; - } else if (current_async->port.count) - return -EBUSY; - } - - current_async = current_async->next_port; - } - } - - /* - * OK, past this point, all the error checking has been done. - * At this point, we start making changes..... - */ - - info->port.flags = ((info->port.flags & ~ASYNC_FLAGS) | - (new_serial.flags & ASYNC_FLAGS)); - info->custom_divisor = new_serial.custom_divisor; - info->close_delay = new_serial.close_delay * HZ/100; - info->closing_wait = new_serial.closing_wait * HZ/100; - - if (change_irq) { - /* - * We need to shutdown the serial port at the old - * port/irq combination. - */ - shutdown(info); - - current_async = ports; - - while (current_async) { - if ((current_async->line >= info->line) && - (current_async->line < (info->line + 8))) - current_async->irq = new_serial.irq; - - current_async = current_async->next_port; - } - - serial_out(info, UART_ESI_CMD1, ESI_SET_ENH_IRQ); - if (info->irq == 9) - serial_out(info, UART_ESI_CMD2, 0x02); - else - serial_out(info, UART_ESI_CMD2, info->irq); - } - } - - if (info->port.flags & ASYNC_INITIALIZED) { - if (((old_info.port.flags & ASYNC_SPD_MASK) != - (info->port.flags & ASYNC_SPD_MASK)) || - (old_info.custom_divisor != info->custom_divisor)) { - if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI) - info->port.tty->alt_speed = 57600; - if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI) - info->port.tty->alt_speed = 115200; - if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI) - info->port.tty->alt_speed = 230400; - if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP) - info->port.tty->alt_speed = 460800; - change_speed(info); - } - } else - retval = startup(info); - - return retval; -} - -static int set_esp_config(struct esp_struct *info, - struct hayes_esp_config __user *new_info) -{ - struct hayes_esp_config new_config; - unsigned int change_dma; - int retval = 0; - struct esp_struct *current_async; - unsigned long flags; - - /* Perhaps a non-sysadmin user should be able to do some of these */ - /* operations. I haven't decided yet. */ - - if (!capable(CAP_SYS_ADMIN)) - return -EPERM; - - if (copy_from_user(&new_config, new_info, sizeof(new_config))) - return -EFAULT; - - if ((new_config.flow_on >= new_config.flow_off) || - (new_config.rx_trigger < 1) || - (new_config.tx_trigger < 1) || - (new_config.flow_off < 1) || - (new_config.flow_on < 1) || - (new_config.rx_trigger > 1023) || - (new_config.tx_trigger > 1023) || - (new_config.flow_off > 1023) || - (new_config.flow_on > 1023) || - (new_config.pio_threshold < 0) || - (new_config.pio_threshold > 1024)) - return -EINVAL; - - if ((new_config.dma_channel != 1) && (new_config.dma_channel != 3)) - new_config.dma_channel = 0; - - if (info->stat_flags & ESP_STAT_NEVER_DMA) - change_dma = new_config.dma_channel; - else - change_dma = (new_config.dma_channel != dma); - - if (change_dma) { - if (new_config.dma_channel) { - /* PIO mode to DMA mode transition OR */ - /* change current DMA channel */ - current_async = ports; - - while (current_async) { - if (current_async == info) { - if (current_async->port.count > 1) - return -EBUSY; - } else if (current_async->port.count) - return -EBUSY; - - current_async = current_async->next_port; - } - - shutdown(info); - dma = new_config.dma_channel; - info->stat_flags &= ~ESP_STAT_NEVER_DMA; - - /* all ports must use the same DMA channel */ - - spin_lock_irqsave(&info->lock, flags); - current_async = ports; - - while (current_async) { - esp_basic_init(current_async); - current_async = current_async->next_port; - } - spin_unlock_irqrestore(&info->lock, flags); - } else { - /* DMA mode to PIO mode only */ - if (info->port.count > 1) - return -EBUSY; - - shutdown(info); - spin_lock_irqsave(&info->lock, flags); - info->stat_flags |= ESP_STAT_NEVER_DMA; - esp_basic_init(info); - spin_unlock_irqrestore(&info->lock, flags); - } - } - - info->config.pio_threshold = new_config.pio_threshold; - - if ((new_config.flow_off != info->config.flow_off) || - (new_config.flow_on != info->config.flow_on)) { - info->config.flow_off = new_config.flow_off; - info->config.flow_on = new_config.flow_on; - - spin_lock_irqsave(&info->lock, flags); - serial_out(info, UART_ESI_CMD1, ESI_SET_FLOW_LVL); - serial_out(info, UART_ESI_CMD2, new_config.flow_off >> 8); - serial_out(info, UART_ESI_CMD2, new_config.flow_off); - serial_out(info, UART_ESI_CMD2, new_config.flow_on >> 8); - serial_out(info, UART_ESI_CMD2, new_config.flow_on); - spin_unlock_irqrestore(&info->lock, flags); - } - - if ((new_config.rx_trigger != info->config.rx_trigger) || - (new_config.tx_trigger != info->config.tx_trigger)) { - info->config.rx_trigger = new_config.rx_trigger; - info->config.tx_trigger = new_config.tx_trigger; - spin_lock_irqsave(&info->lock, flags); - serial_out(info, UART_ESI_CMD1, ESI_SET_TRIGGER); - serial_out(info, UART_ESI_CMD2, - new_config.rx_trigger >> 8); - serial_out(info, UART_ESI_CMD2, new_config.rx_trigger); - serial_out(info, UART_ESI_CMD2, - new_config.tx_trigger >> 8); - serial_out(info, UART_ESI_CMD2, new_config.tx_trigger); - spin_unlock_irqrestore(&info->lock, flags); - } - - if (new_config.rx_timeout != info->config.rx_timeout) { - info->config.rx_timeout = new_config.rx_timeout; - spin_lock_irqsave(&info->lock, flags); - - if (info->IER & UART_IER_RDI) { - serial_out(info, UART_ESI_CMD1, - ESI_SET_RX_TIMEOUT); - serial_out(info, UART_ESI_CMD2, - new_config.rx_timeout); - } - - spin_unlock_irqrestore(&info->lock, flags); - } - - if (!(info->port.flags & ASYNC_INITIALIZED)) - retval = startup(info); - - return retval; -} - -/* - * get_lsr_info - get line status register info - * - * Purpose: Let user call ioctl() to get info when the UART physically - * is emptied. On bus types like RS485, the transmitter must - * release the bus after transmitting. This must be done when - * the transmit shift register is empty, not be done when the - * transmit holding register is empty. This functionality - * allows an RS485 driver to be written in user space. - */ -static int get_lsr_info(struct esp_struct *info, unsigned int __user *value) -{ - unsigned char status; - unsigned int result; - unsigned long flags; - - spin_lock_irqsave(&info->lock, flags); - serial_out(info, UART_ESI_CMD1, ESI_GET_UART_STAT); - status = serial_in(info, UART_ESI_STAT1); - spin_unlock_irqrestore(&info->lock, flags); - result = ((status & UART_LSR_TEMT) ? TIOCSER_TEMT : 0); - return put_user(result, value); -} - - -static int esp_tiocmget(struct tty_struct *tty, struct file *file) -{ - struct esp_struct *info = tty->driver_data; - unsigned char control, status; - unsigned long flags; - - if (serial_paranoia_check(info, tty->name, __func__)) - return -ENODEV; - if (tty->flags & (1 << TTY_IO_ERROR)) - return -EIO; - - control = info->MCR; - - spin_lock_irqsave(&info->lock, flags); - serial_out(info, UART_ESI_CMD1, ESI_GET_UART_STAT); - status = serial_in(info, UART_ESI_STAT2); - spin_unlock_irqrestore(&info->lock, flags); - - return ((control & UART_MCR_RTS) ? TIOCM_RTS : 0) - | ((control & UART_MCR_DTR) ? TIOCM_DTR : 0) - | ((status & UART_MSR_DCD) ? TIOCM_CAR : 0) - | ((status & UART_MSR_RI) ? TIOCM_RNG : 0) - | ((status & UART_MSR_DSR) ? TIOCM_DSR : 0) - | ((status & UART_MSR_CTS) ? TIOCM_CTS : 0); -} - -static int esp_tiocmset(struct tty_struct *tty, struct file *file, - unsigned int set, unsigned int clear) -{ - struct esp_struct *info = tty->driver_data; - unsigned long flags; - - if (serial_paranoia_check(info, tty->name, __func__)) - return -ENODEV; - if (tty->flags & (1 << TTY_IO_ERROR)) - return -EIO; - - spin_lock_irqsave(&info->lock, flags); - - if (set & TIOCM_RTS) - info->MCR |= UART_MCR_RTS; - if (set & TIOCM_DTR) - info->MCR |= UART_MCR_DTR; - - if (clear & TIOCM_RTS) - info->MCR &= ~UART_MCR_RTS; - if (clear & TIOCM_DTR) - info->MCR &= ~UART_MCR_DTR; - - serial_out(info, UART_ESI_CMD1, ESI_WRITE_UART); - serial_out(info, UART_ESI_CMD2, UART_MCR); - serial_out(info, UART_ESI_CMD2, info->MCR); - - spin_unlock_irqrestore(&info->lock, flags); - return 0; -} - -/* - * rs_break() --- routine which turns the break handling on or off - */ -static int esp_break(struct tty_struct *tty, int break_state) -{ - struct esp_struct *info = tty->driver_data; - unsigned long flags; - - if (serial_paranoia_check(info, tty->name, "esp_break")) - return -EINVAL; - - if (break_state == -1) { - spin_lock_irqsave(&info->lock, flags); - serial_out(info, UART_ESI_CMD1, ESI_ISSUE_BREAK); - serial_out(info, UART_ESI_CMD2, 0x01); - spin_unlock_irqrestore(&info->lock, flags); - - /* FIXME - new style wait needed here */ - interruptible_sleep_on(&info->break_wait); - } else { - spin_lock_irqsave(&info->lock, flags); - serial_out(info, UART_ESI_CMD1, ESI_ISSUE_BREAK); - serial_out(info, UART_ESI_CMD2, 0x00); - spin_unlock_irqrestore(&info->lock, flags); - } - return 0; -} - -static int rs_ioctl(struct tty_struct *tty, struct file *file, - unsigned int cmd, unsigned long arg) -{ - struct esp_struct *info = tty->driver_data; - struct async_icount cprev, cnow; /* kernel counter temps */ - struct serial_icounter_struct __user *p_cuser; /* user space */ - void __user *argp = (void __user *)arg; - unsigned long flags; - int ret; - - if (serial_paranoia_check(info, tty->name, "rs_ioctl")) - return -ENODEV; - - if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) && - (cmd != TIOCSERCONFIG) && (cmd != TIOCSERGWILD) && - (cmd != TIOCSERSWILD) && (cmd != TIOCSERGSTRUCT) && - (cmd != TIOCMIWAIT) && (cmd != TIOCGICOUNT) && - (cmd != TIOCGHAYESESP) && (cmd != TIOCSHAYESESP)) { - if (tty->flags & (1 << TTY_IO_ERROR)) - return -EIO; - } - - switch (cmd) { - case TIOCGSERIAL: - return get_serial_info(info, argp); - case TIOCSSERIAL: - lock_kernel(); - ret = set_serial_info(info, argp); - unlock_kernel(); - return ret; - case TIOCSERGWILD: - return put_user(0L, (unsigned long __user *)argp); - case TIOCSERGETLSR: /* Get line status register */ - return get_lsr_info(info, argp); - case TIOCSERSWILD: - if (!capable(CAP_SYS_ADMIN)) - return -EPERM; - return 0; - /* - * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change - * - mask passed in arg for lines of interest - * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking) - * Caller should use TIOCGICOUNT to see which one it was - */ - case TIOCMIWAIT: - spin_lock_irqsave(&info->lock, flags); - cprev = info->icount; /* note the counters on entry */ - spin_unlock_irqrestore(&info->lock, flags); - while (1) { - /* FIXME: convert to new style wakeup */ - interruptible_sleep_on(&info->port.delta_msr_wait); - /* see if a signal did it */ - if (signal_pending(current)) - return -ERESTARTSYS; - spin_lock_irqsave(&info->lock, flags); - cnow = info->icount; /* atomic copy */ - spin_unlock_irqrestore(&info->lock, flags); - if (cnow.rng == cprev.rng && - cnow.dsr == cprev.dsr && - cnow.dcd == cprev.dcd && - cnow.cts == cprev.cts) - return -EIO; /* no change => error */ - if (((arg & TIOCM_RNG) && - (cnow.rng != cprev.rng)) || - ((arg & TIOCM_DSR) && - (cnow.dsr != cprev.dsr)) || - ((arg & TIOCM_CD) && - (cnow.dcd != cprev.dcd)) || - ((arg & TIOCM_CTS) && - (cnow.cts != cprev.cts))) { - return 0; - } - cprev = cnow; - } - /* NOTREACHED */ - /* - * Get counter of input serial line interrupts (DCD,RI,DSR,CTS) - * Return: write counters to the user passed counter struct - * NB: both 1->0 and 0->1 transitions are counted except for - * RI where only 0->1 is counted. - */ - case TIOCGICOUNT: - spin_lock_irqsave(&info->lock, flags); - cnow = info->icount; - spin_unlock_irqrestore(&info->lock, flags); - p_cuser = argp; - if (put_user(cnow.cts, &p_cuser->cts) || - put_user(cnow.dsr, &p_cuser->dsr) || - put_user(cnow.rng, &p_cuser->rng) || - put_user(cnow.dcd, &p_cuser->dcd)) - return -EFAULT; - return 0; - case TIOCGHAYESESP: - return get_esp_config(info, argp); - case TIOCSHAYESESP: - lock_kernel(); - ret = set_esp_config(info, argp); - unlock_kernel(); - return ret; - default: - return -ENOIOCTLCMD; - } - return 0; -} - -static void rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios) -{ - struct esp_struct *info = tty->driver_data; - unsigned long flags; - - change_speed(info); - - spin_lock_irqsave(&info->lock, flags); - - /* Handle transition to B0 status */ - if ((old_termios->c_cflag & CBAUD) && - !(tty->termios->c_cflag & CBAUD)) { - info->MCR &= ~(UART_MCR_DTR|UART_MCR_RTS); - serial_out(info, UART_ESI_CMD1, ESI_WRITE_UART); - serial_out(info, UART_ESI_CMD2, UART_MCR); - serial_out(info, UART_ESI_CMD2, info->MCR); - } - - /* Handle transition away from B0 status */ - if (!(old_termios->c_cflag & CBAUD) && - (tty->termios->c_cflag & CBAUD)) { - info->MCR |= (UART_MCR_DTR | UART_MCR_RTS); - serial_out(info, UART_ESI_CMD1, ESI_WRITE_UART); - serial_out(info, UART_ESI_CMD2, UART_MCR); - serial_out(info, UART_ESI_CMD2, info->MCR); - } - - spin_unlock_irqrestore(&info->lock, flags); - - /* Handle turning of CRTSCTS */ - if ((old_termios->c_cflag & CRTSCTS) && - !(tty->termios->c_cflag & CRTSCTS)) { - rs_start(tty); - } -} - -/* - * ------------------------------------------------------------ - * rs_close() - * - * This routine is called when the serial port gets closed. First, we - * wait for the last remaining data to be sent. Then, we unlink its - * async structure from the interrupt chain if necessary, and we free - * that IRQ if nothing is left in the chain. - * ------------------------------------------------------------ - */ -static void rs_close(struct tty_struct *tty, struct file *filp) -{ - struct esp_struct *info = tty->driver_data; - unsigned long flags; - - if (!info || serial_paranoia_check(info, tty->name, "rs_close")) - return; - - spin_lock_irqsave(&info->lock, flags); - - if (tty_hung_up_p(filp)) { - DBG_CNT("before DEC-hung"); - goto out; - } - -#ifdef SERIAL_DEBUG_OPEN - printk(KERN_DEBUG "rs_close ttys%d, count = %d\n", - info->line, info->port.count); -#endif - if (tty->count == 1 && info->port.count != 1) { - /* - * Uh, oh. tty->count is 1, which means that the tty - * structure will be freed. Info->count should always - * be one in these conditions. If it's greater than - * one, we've got real problems, since it means the - * serial port won't be shutdown. - */ - printk(KERN_DEBUG "rs_close: bad serial port count; tty->count is 1, info->port.count is %d\n", info->port.count); - info->port.count = 1; - } - if (--info->port.count < 0) { - printk(KERN_ERR "rs_close: bad serial port count for ttys%d: %d\n", - info->line, info->port.count); - info->port.count = 0; - } - if (info->port.count) { - DBG_CNT("before DEC-2"); - goto out; - } - info->port.flags |= ASYNC_CLOSING; - - spin_unlock_irqrestore(&info->lock, flags); - /* - * Now we wait for the transmit buffer to clear; and we notify - * the line discipline to only process XON/XOFF characters. - */ - tty->closing = 1; - if (info->closing_wait != ASYNC_CLOSING_WAIT_NONE) - tty_wait_until_sent(tty, info->closing_wait); - /* - * At this point we stop accepting input. To do this, we - * disable the receive line status interrupts, and tell the - * interrupt driver to stop checking the data ready bit in the - * line status register. - */ - /* info->IER &= ~UART_IER_RLSI; */ - info->IER &= ~UART_IER_RDI; - info->read_status_mask &= ~UART_LSR_DR; - if (info->port.flags & ASYNC_INITIALIZED) { - - spin_lock_irqsave(&info->lock, flags); - serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK); - serial_out(info, UART_ESI_CMD2, info->IER); - - /* disable receive timeout */ - serial_out(info, UART_ESI_CMD1, ESI_SET_RX_TIMEOUT); - serial_out(info, UART_ESI_CMD2, 0x00); - - spin_unlock_irqrestore(&info->lock, flags); - - /* - * Before we drop DTR, make sure the UART transmitter - * has completely drained; this is especially - * important if there is a transmit FIFO! - */ - rs_wait_until_sent(tty, info->timeout); - } - shutdown(info); - rs_flush_buffer(tty); - tty_ldisc_flush(tty); - tty->closing = 0; - info->port.tty = NULL; - - if (info->port.blocked_open) { - if (info->close_delay) - msleep_interruptible(jiffies_to_msecs(info->close_delay)); - wake_up_interruptible(&info->port.open_wait); - } - info->port.flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING); - wake_up_interruptible(&info->port.close_wait); - return; - -out: - spin_unlock_irqrestore(&info->lock, flags); -} - -static void rs_wait_until_sent(struct tty_struct *tty, int timeout) -{ - struct esp_struct *info = tty->driver_data; - unsigned long orig_jiffies, char_time; - unsigned long flags; - - if (serial_paranoia_check(info, tty->name, "rs_wait_until_sent")) - return; - - orig_jiffies = jiffies; - char_time = ((info->timeout - HZ / 50) / 1024) / 5; - - if (!char_time) - char_time = 1; - - spin_lock_irqsave(&info->lock, flags); - serial_out(info, UART_ESI_CMD1, ESI_NO_COMMAND); - serial_out(info, UART_ESI_CMD1, ESI_GET_TX_AVAIL); - - while ((serial_in(info, UART_ESI_STAT1) != 0x03) || - (serial_in(info, UART_ESI_STAT2) != 0xff)) { - - spin_unlock_irqrestore(&info->lock, flags); - msleep_interruptible(jiffies_to_msecs(char_time)); - - if (signal_pending(current)) - return; - - if (timeout && time_after(jiffies, orig_jiffies + timeout)) - return; - - spin_lock_irqsave(&info->lock, flags); - serial_out(info, UART_ESI_CMD1, ESI_NO_COMMAND); - serial_out(info, UART_ESI_CMD1, ESI_GET_TX_AVAIL); - } - spin_unlock_irqrestore(&info->lock, flags); - set_current_state(TASK_RUNNING); -} - -/* - * esp_hangup() --- called by tty_hangup() when a hangup is signaled. - */ -static void esp_hangup(struct tty_struct *tty) -{ - struct esp_struct *info = tty->driver_data; - - if (serial_paranoia_check(info, tty->name, "esp_hangup")) - return; - - rs_flush_buffer(tty); - shutdown(info); - info->port.count = 0; - info->port.flags &= ~ASYNC_NORMAL_ACTIVE; - info->port.tty = NULL; - wake_up_interruptible(&info->port.open_wait); -} - -static int esp_carrier_raised(struct tty_port *port) -{ - struct esp_struct *info = container_of(port, struct esp_struct, port); - serial_out(info, UART_ESI_CMD1, ESI_GET_UART_STAT); - if (serial_in(info, UART_ESI_STAT2) & UART_MSR_DCD) - return 1; - return 0; -} - -/* - * ------------------------------------------------------------ - * esp_open() and friends - * ------------------------------------------------------------ - */ -static int block_til_ready(struct tty_struct *tty, struct file *filp, - struct esp_struct *info) -{ - DECLARE_WAITQUEUE(wait, current); - int retval; - int do_clocal = 0; - unsigned long flags; - int cd; - struct tty_port *port = &info->port; - - /* - * If the device is in the middle of being closed, then block - * until it's done, and then try again. - */ - if (tty_hung_up_p(filp) || - (port->flags & ASYNC_CLOSING)) { - if (port->flags & ASYNC_CLOSING) - interruptible_sleep_on(&port->close_wait); -#ifdef SERIAL_DO_RESTART - if (port->flags & ASYNC_HUP_NOTIFY) - return -EAGAIN; - else - return -ERESTARTSYS; -#else - return -EAGAIN; -#endif - } - - /* - * If non-blocking mode is set, or the port is not enabled, - * then make the check up front and then exit. - */ - if ((filp->f_flags & O_NONBLOCK) || - (tty->flags & (1 << TTY_IO_ERROR))) { - port->flags |= ASYNC_NORMAL_ACTIVE; - return 0; - } - - if (tty->termios->c_cflag & CLOCAL) - do_clocal = 1; - - /* - * Block waiting for the carrier detect and the line to become - * free (i.e., not in use by the callout). While we are in - * this loop, port->count is dropped by one, so that - * rs_close() knows when to free things. We restore it upon - * exit, either normal or abnormal. - */ - retval = 0; - add_wait_queue(&port->open_wait, &wait); -#ifdef SERIAL_DEBUG_OPEN - printk(KERN_DEBUG "block_til_ready before block: ttys%d, count = %d\n", - info->line, port->count); -#endif - spin_lock_irqsave(&info->lock, flags); - if (!tty_hung_up_p(filp)) - port->count--; - port->blocked_open++; - while (1) { - if ((tty->termios->c_cflag & CBAUD)) { - unsigned int scratch; - - serial_out(info, UART_ESI_CMD1, ESI_READ_UART); - serial_out(info, UART_ESI_CMD2, UART_MCR); - scratch = serial_in(info, UART_ESI_STAT1); - serial_out(info, UART_ESI_CMD1, ESI_WRITE_UART); - serial_out(info, UART_ESI_CMD2, UART_MCR); - serial_out(info, UART_ESI_CMD2, - scratch | UART_MCR_DTR | UART_MCR_RTS); - } - set_current_state(TASK_INTERRUPTIBLE); - if (tty_hung_up_p(filp) || - !(port->flags & ASYNC_INITIALIZED)) { -#ifdef SERIAL_DO_RESTART - if (port->flags & ASYNC_HUP_NOTIFY) - retval = -EAGAIN; - else - retval = -ERESTARTSYS; -#else - retval = -EAGAIN; -#endif - break; - } - - cd = tty_port_carrier_raised(port); - - if (!(port->flags & ASYNC_CLOSING) && - (do_clocal)) - break; - if (signal_pending(current)) { - retval = -ERESTARTSYS; - break; - } -#ifdef SERIAL_DEBUG_OPEN - printk(KERN_DEBUG "block_til_ready blocking: ttys%d, count = %d\n", - info->line, port->count); -#endif - spin_unlock_irqrestore(&info->lock, flags); - schedule(); - spin_lock_irqsave(&info->lock, flags); - } - set_current_state(TASK_RUNNING); - remove_wait_queue(&port->open_wait, &wait); - if (!tty_hung_up_p(filp)) - port->count++; - port->blocked_open--; - spin_unlock_irqrestore(&info->lock, flags); -#ifdef SERIAL_DEBUG_OPEN - printk(KERN_DEBUG "block_til_ready after blocking: ttys%d, count = %d\n", - info->line, port->count); -#endif - if (retval) - return retval; - port->flags |= ASYNC_NORMAL_ACTIVE; - return 0; -} - -/* - * This routine is called whenever a serial port is opened. It - * enables interrupts for a serial port, linking in its async structure into - * the IRQ chain. It also performs the serial-specific - * initialization for the tty structure. - */ -static int esp_open(struct tty_struct *tty, struct file *filp) -{ - struct esp_struct *info; - int retval, line; - unsigned long flags; - - line = tty->index; - if ((line < 0) || (line >= NR_PORTS)) - return -ENODEV; - - /* find the port in the chain */ - - info = ports; - - while (info && (info->line != line)) - info = info->next_port; - - if (!info) { - serial_paranoia_check(info, tty->name, "esp_open"); - return -ENODEV; - } - -#ifdef SERIAL_DEBUG_OPEN - printk(KERN_DEBUG "esp_open %s, count = %d\n", tty->name, info->port.count); -#endif - spin_lock_irqsave(&info->lock, flags); - info->port.count++; - tty->driver_data = info; - info->port.tty = tty; - - spin_unlock_irqrestore(&info->lock, flags); - - /* - * Start up serial port - */ - retval = startup(info); - if (retval) - return retval; - - retval = block_til_ready(tty, filp, info); - if (retval) { -#ifdef SERIAL_DEBUG_OPEN - printk(KERN_DEBUG "esp_open returning after block_til_ready with %d\n", - retval); -#endif - return retval; - } -#ifdef SERIAL_DEBUG_OPEN - printk(KERN_DEBUG "esp_open %s successful...", tty->name); -#endif - return 0; -} - -/* - * --------------------------------------------------------------------- - * espserial_init() and friends - * - * espserial_init() is called at boot-time to initialize the serial driver. - * --------------------------------------------------------------------- - */ - -/* - * This routine prints out the appropriate serial driver version - * number, and identifies which options were configured into this - * driver. - */ - -static void __init show_serial_version(void) -{ - printk(KERN_INFO "%s version %s (DMA %u)\n", - serial_name, serial_version, dma); -} - -/* - * This routine is called by espserial_init() to initialize a specific serial - * port. - */ -static int autoconfig(struct esp_struct *info) -{ - int port_detected = 0; - unsigned long flags; - - if (!request_region(info->io_port, REGION_SIZE, "esp serial")) - return -EIO; - - spin_lock_irqsave(&info->lock, flags); - /* - * Check for ESP card - */ - - if (serial_in(info, UART_ESI_BASE) == 0xf3) { - serial_out(info, UART_ESI_CMD1, 0x00); - serial_out(info, UART_ESI_CMD1, 0x01); - - if ((serial_in(info, UART_ESI_STAT2) & 0x70) == 0x20) { - port_detected = 1; - - if (!(info->irq)) { - serial_out(info, UART_ESI_CMD1, 0x02); - - if (serial_in(info, UART_ESI_STAT1) & 0x01) - info->irq = 3; - else - info->irq = 4; - } - - - /* put card in enhanced mode */ - /* this prevents access through */ - /* the "old" IO ports */ - esp_basic_init(info); - - /* clear out MCR */ - serial_out(info, UART_ESI_CMD1, ESI_WRITE_UART); - serial_out(info, UART_ESI_CMD2, UART_MCR); - serial_out(info, UART_ESI_CMD2, 0x00); - } - } - if (!port_detected) - release_region(info->io_port, REGION_SIZE); - - spin_unlock_irqrestore(&info->lock, flags); - return (port_detected); -} - -static const struct tty_operations esp_ops = { - .open = esp_open, - .close = rs_close, - .write = rs_write, - .put_char = rs_put_char, - .flush_chars = rs_flush_chars, - .write_room = rs_write_room, - .chars_in_buffer = rs_chars_in_buffer, - .flush_buffer = rs_flush_buffer, - .ioctl = rs_ioctl, - .throttle = rs_throttle, - .unthrottle = rs_unthrottle, - .set_termios = rs_set_termios, - .stop = rs_stop, - .start = rs_start, - .hangup = esp_hangup, - .break_ctl = esp_break, - .wait_until_sent = rs_wait_until_sent, - .tiocmget = esp_tiocmget, - .tiocmset = esp_tiocmset, -}; - -static const struct tty_port_operations esp_port_ops = { - .esp_carrier_raised, -}; - -/* - * The serial driver boot-time initialization code! - */ -static int __init espserial_init(void) -{ - int i, offset; - struct esp_struct *info; - struct esp_struct *last_primary = NULL; - int esp[] = { 0x100, 0x140, 0x180, 0x200, 0x240, 0x280, 0x300, 0x380 }; - - esp_driver = alloc_tty_driver(NR_PORTS); - if (!esp_driver) - return -ENOMEM; - - for (i = 0; i < NR_PRIMARY; i++) { - if (irq[i] != 0) { - if ((irq[i] < 2) || (irq[i] > 15) || (irq[i] == 6) || - (irq[i] == 8) || (irq[i] == 13)) - irq[i] = 0; - else if (irq[i] == 2) - irq[i] = 9; - } - } - - if ((dma != 1) && (dma != 3)) - dma = 0; - - if ((rx_trigger < 1) || (rx_trigger > 1023)) - rx_trigger = 768; - - if ((tx_trigger < 1) || (tx_trigger > 1023)) - tx_trigger = 768; - - if ((flow_off < 1) || (flow_off > 1023)) - flow_off = 1016; - - if ((flow_on < 1) || (flow_on > 1023)) - flow_on = 944; - - if ((rx_timeout < 0) || (rx_timeout > 255)) - rx_timeout = 128; - - if (flow_on >= flow_off) - flow_on = flow_off - 1; - - show_serial_version(); - - /* Initialize the tty_driver structure */ - - esp_driver->owner = THIS_MODULE; - esp_driver->name = "ttyP"; - esp_driver->major = ESP_IN_MAJOR; - esp_driver->minor_start = 0; - esp_driver->type = TTY_DRIVER_TYPE_SERIAL; - esp_driver->subtype = SERIAL_TYPE_NORMAL; - esp_driver->init_termios = tty_std_termios; - esp_driver->init_termios.c_cflag = - B9600 | CS8 | CREAD | HUPCL | CLOCAL; - esp_driver->init_termios.c_ispeed = 9600; - esp_driver->init_termios.c_ospeed = 9600; - esp_driver->flags = TTY_DRIVER_REAL_RAW; - tty_set_operations(esp_driver, &esp_ops); - if (tty_register_driver(esp_driver)) { - printk(KERN_ERR "Couldn't register esp serial driver"); - put_tty_driver(esp_driver); - return 1; - } - - info = kzalloc(sizeof(struct esp_struct), GFP_KERNEL); - - if (!info) { - printk(KERN_ERR "Couldn't allocate memory for esp serial device information\n"); - tty_unregister_driver(esp_driver); - put_tty_driver(esp_driver); - return 1; - } - - spin_lock_init(&info->lock); - /* rx_trigger, tx_trigger are needed by autoconfig */ - info->config.rx_trigger = rx_trigger; - info->config.tx_trigger = tx_trigger; - - i = 0; - offset = 0; - - do { - tty_port_init(&info->port); - info->port.ops = &esp_port_ops; - info->io_port = esp[i] + offset; - info->irq = irq[i]; - info->line = (i * 8) + (offset / 8); - - if (!autoconfig(info)) { - i++; - offset = 0; - continue; - } - - info->custom_divisor = (divisor[i] >> (offset / 2)) & 0xf; - info->port.flags = STD_COM_FLAGS; - if (info->custom_divisor) - info->port.flags |= ASYNC_SPD_CUST; - info->magic = ESP_MAGIC; - info->close_delay = 5*HZ/10; - info->closing_wait = 30*HZ; - info->config.rx_timeout = rx_timeout; - info->config.flow_on = flow_on; - info->config.flow_off = flow_off; - info->config.pio_threshold = pio_threshold; - info->next_port = ports; - init_waitqueue_head(&info->break_wait); - ports = info; - printk(KERN_INFO "ttyP%d at 0x%04x (irq = %d) is an ESP ", - info->line, info->io_port, info->irq); - - if (info->line % 8) { - printk("secondary port\n"); - /* 8 port cards can't do DMA */ - info->stat_flags |= ESP_STAT_NEVER_DMA; - - if (last_primary) - last_primary->stat_flags |= ESP_STAT_NEVER_DMA; - } else { - printk("primary port\n"); - last_primary = info; - irq[i] = info->irq; - } - - if (!dma) - info->stat_flags |= ESP_STAT_NEVER_DMA; - - info = kzalloc(sizeof(struct esp_struct), GFP_KERNEL); - if (!info) { - printk(KERN_ERR "Couldn't allocate memory for esp serial device information\n"); - /* allow use of the already detected ports */ - return 0; - } - - spin_lock_init(&info->lock); - /* rx_trigger, tx_trigger are needed by autoconfig */ - info->config.rx_trigger = rx_trigger; - info->config.tx_trigger = tx_trigger; - - if (offset == 56) { - i++; - offset = 0; - } else { - offset += 8; - } - } while (i < NR_PRIMARY); - - /* free the last port memory allocation */ - kfree(info); - - return 0; -} - -static void __exit espserial_exit(void) -{ - int e1; - struct esp_struct *temp_async; - struct esp_pio_buffer *pio_buf; - - e1 = tty_unregister_driver(esp_driver); - if (e1) - printk(KERN_ERR "esp: failed to unregister driver (%d)\n", e1); - put_tty_driver(esp_driver); - - while (ports) { - if (ports->io_port) - release_region(ports->io_port, REGION_SIZE); - temp_async = ports->next_port; - kfree(ports); - ports = temp_async; - } - - if (dma_buffer) - free_pages((unsigned long)dma_buffer, - get_order(DMA_BUFFER_SZ)); - - while (free_pio_buf) { - pio_buf = free_pio_buf->next; - kfree(free_pio_buf); - free_pio_buf = pio_buf; - } -} - -module_init(espserial_init); -module_exit(espserial_exit); -- cgit v1.2.3-59-g8ed1b