.\" $OpenBSD: eigrpd.conf.5,v 1.10 2020/05/16 16:58:11 jmc Exp $ .\" .\" Copyright (c) 2015 Renato Westphal .\" Copyright (c) 2005 Esben Norby .\" Copyright (c) 2004 Claudio Jeker .\" Copyright (c) 2003, 2004 Henning Brauer .\" Copyright (c) 2002 Daniel Hartmeier .\" .\" Permission to use, copy, modify, and distribute this software for any .\" purpose with or without fee is hereby granted, provided that the above .\" copyright notice and this permission notice appear in all copies. .\" .\" THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES .\" WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF .\" MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR .\" ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES .\" WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN .\" ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF .\" OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. .\" .Dd $Mdocdate: May 16 2020 $ .Dt EIGRPD.CONF 5 .Os .Sh NAME .Nm eigrpd.conf .Nd Enhanced Interior Gateway Routing Protocol daemon configuration file .Sh DESCRIPTION The .Xr eigrpd 8 daemon implements the Enhanced Interior Gateway Routing Protocol. .Pp The .Nm config file is divided into the following main sections: .Bl -tag -width xxxx .It Sy Macros User-defined variables may be defined and used later, simplifying the configuration file. .It Sy Global Configuration Global settings for .Xr eigrpd 8 . .It Sy Routing Instances Multiple routing instances can be defined. Routing instances are defined hierarchically by address-family and then autonomous-system. .It Sy Interfaces Configuration Interface-specific parameters. .El .Pp Argument names not beginning with a letter, digit, or underscore must be quoted. .Pp Additional configuration files can be included with the .Ic include keyword, for example: .Bd -literal -offset indent include "/etc/eigrpd.sub.conf" .Ed .Sh MACROS Macros can be defined that will later be expanded in context. Macro names must start with a letter, digit, or underscore, and may contain any of those characters. Macro names may not be reserved words (for example, .Ic bandwidth , .Ic interface , or .Ic hello-interval ) . Macros are not expanded inside quotes. .Pp For example: .Bd -literal -offset indent fastethernet="100000" address-family ipv4 { autonomous-system 1 { interface em1 { bandwidth $fastethernet } } } .Ed .Pp The same can be accomplished by specifying the bandwidth globally or within the address-family or autonomous-system declaration. .Sh GLOBAL CONFIGURATION Several settings can be configured globally, per address-family, per autonomous-system and per interface. The only settings that can be set globally and not overruled are listed below. .Bl -tag -width Ds .It Ic fib-priority-internal Ar prio Set the routing priority of EIGRP internal routes to .Ar prio . The default is 28. .It Ic fib-priority-external Ar prio Set the routing priority of EIGRP external routes to .Ar prio . This option may be used as a simple loop-prevention mechanism when another routing protocol is being redistributed into EIGRP. The default is 28. .It Ic fib-priority-summary Ar prio Set the routing priority of EIGRP summary routes to .Ar prio . The default is 28. .It Xo .Ic fib-update .Pq Ic yes Ns | Ns Ic no .Xc If set to .Ic \&no , do not update the Forwarding Information Base, a.k.a. the kernel routing table. The default is .Ic yes . .It Ic rdomain Ar tableid Specifies the routing table .Xr eigrpd 8 should modify. Table 0 is the default table. .It Ic router-id Ar address Set the router ID; if not specified, the numerically lowest IP address of the router will be used. .El .Sh ROUTING INSTANCES Multiple routing instances can be defined. Routing instances are defined hierarchically by address-family and then autonomous-system. .Bd -literal -offset indent address-family ipv4 { ... autonomous-system 1 { ... interface em0 { ... } } } .Ed .Pp Routing-instance specific parameters are listed below. .Bl -tag -width Ds .It Ic active-timeout Ar minutes Set the maximum time to wait before declaring a route to be in the stuck in active state. If 0 is given, the active timeout is disabled. The default value is 3; valid range is 0\-65535. .It Xo .Ic address-family .Pq Ic ipv4 Ns | Ns Ic ipv6 .Xc Specify an address-family section, grouping one or more autonomous-systems. .It Ic autonomous-system Ar number Specify the autonomous-system, grouping one or more interfaces. Valid range is 1\-65535. .It Ic default-metric Ar bandwidth delay reliability load mtu Specify a default metric for all routes redistributed into EIGRP. Valid ranges are: 1\-10000000 for the bandwidth, 1\-16777215 for the delay, 1\-255 for the reliability, 1\-255 for the load and 1\-65535 for the mtu. .It Ic k-values Ar K1 Ar K2 Ar K3 Ar K4 Ar K5 Ar K6 Set the coefficients used by the composite metric calculation. Two routers become neighbors only if their K-values are the same. For K1 and K3, The default value is 1. For K2, K4, K5 and K6 the default value is 0; valid range is 1\-254. .It Ic maximum-hops Ar number Advertise as unreachable the routes with a hop count higher than specified. The default value is 100; valid range is 1\-255. .It Ic maximum-paths Ar number Specify the maximum number of ECMP paths to be installed in the FIB for each route. The default value is 4; valid range is 1\-32. .It Xo .Op Ic no .Ic redistribute .Sm off .Po Ic static Ns | Ns Ic connected Ns | Ns Ic ospf | Ns Ic rip | Ns .Ic default Pc .Sm on .Op Ic metric Ar bandwidth delay reliability load mtu .Xc .It Xo .Op Ic no .Ic redistribute Ar prefix .Op Ic metric Ar bandwidth delay reliability load mtu .Xc If set to .Ic connected , routes to directly attached networks will be announced over EIGRP. If set to .Ic static , static routes will be announced over EIGRP. If set to .Ic ospf , OSPF routes will be announced over EIGRP. If set to .Ic rip , RIP routes will be announced over EIGRP. If set to .Ic default , a default route pointing to this router will be announced over EIGRP. It is possible to specify a network range with .Ar prefix ; networks need to be part of that range to be redistributed. By default no additional routes will be announced over EIGRP. .Pp .Ic redistribute statements are evaluated in sequential order, from first to last. The first matching rule decides if a route should be redistributed or not. Matching rules starting with .Ic no will force the route to be not announced. The only exception is .Ic default , which will be set no matter what, and additionally .Ic no cannot be used together with it. .Pp It is possible to set the route .Ic metric for each redistribute rule. .It Ic variance Ar multiplier Set the variance used to permit the installation of feasible successors in the FIB if their metric is lower than the metric of the successor multiplied by the specified multiplier. The default value is 1; valid range is 1\-128. .El .Sh INTERFACES Each interface can have several parameters configured individually, otherwise they are inherited. Interfaces can pertain to multiple routing instances. An interface is specified by its name. .Bd -literal -offset indent interface em0 { ... } .Ed .Pp Interface-specific parameters are listed below. .Bl -tag -width Ds .It Ic bandwidth Ar bandwidth Set the interface bandwidth in kilobits per second. The bandwidth is used as part of the EIGRP composite metric. The default value is 100000; valid range is 1\-10000000. .It Ic delay Ar delay Set the interface delay in tens of microseconds. The delay is used as part of the EIGRP composite metric. The default value is 10; valid range is 1\-16777215. .It Ic hello-interval Ar seconds Set the hello interval. The default value is 5; valid range is 1\-65535 seconds. .It Ic holdtime Ar seconds Set the hello holdtime. The default value is 15; valid range is 1\-65535 seconds. .It Ic passive Prevent transmission and reception of EIGRP packets on this interface. .It Xo .Ic split-horizon .Pq Ic yes Ns | Ns Ic no .Xc If set to .Ic \&no , the split horizon rule will be disabled on this interface. This option should be used with caution since it can introduce routing loops in point-to-point or broadcast networks. The default is .Ic yes . .It Ic summary-address Ar address Ns Li / Ns Ar len Configure a summary aggregate address for this interface. Multiple summary addresses can be configured. .El .Sh FILES .Bl -tag -width /etc/examples/eigrpd.conf -compact .It Pa /etc/eigrpd.conf .Xr eigrpd 8 configuration file. .It Pa /etc/examples/eigrpd.conf Example configuration file. .El .Sh SEE ALSO .Xr eigrpctl 8 , .Xr eigrpd 8 , .Xr rc.conf.local 8 .Sh HISTORY The .Nm file format first appeared in .Ox 5.9 . .Sh AUTHORS The .Xr eigrpd 8 program was written by .An Renato Westphal Aq Mt renato@openbsd.org .