Merge master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6

* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide: remove CONFIG_IDEDMA_{ICS,PCI}_AUTO config options
  ide: don't allow DMA to be enabled if CONFIG_IDEDMA_{ICS,PCI}_AUTO=n
  scc_pata: dependency fix
  jmicron: make ide jmicron driver play nice with libata ones
  ide: remove static prototypes from include/asm-mips/mach-au1x00/au1xxx_ide.h
  ide: au1xxx: fix use of mixed declarations and code
  cmd64x: fix recovery time calculation (take 3)

12 files changed, 57 insertions, 128 deletions

diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index 3f76987d818a..8f1fd017679b 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -434,24 +434,8 @@ config BLK_DEV_IDEDMA_FORCED
 
 	  Generally say N here.
 
-config IDEDMA_PCI_AUTO
-	bool "Use PCI DMA by default when available"
-	---help---
-	  Prior to kernel version 2.1.112, Linux used to automatically use
-	  DMA for IDE drives and chipsets which support it. Due to concerns
-	  about a couple of cases where buggy hardware may have caused damage,
-	  the default is now to NOT use DMA automatically. To revert to the
-	  previous behaviour, say Y to this question.
-
-	  If you suspect your hardware is at all flakey, say N here.
-	  Do NOT email the IDE kernel people regarding this issue!
-
-	  It is normally safe to answer Y to this question unless your
-	  motherboard uses a VIA VP2 chipset, in which case you should say N.
-
 config IDEDMA_ONLYDISK
 	bool "Enable DMA only for disks "
-	depends on IDEDMA_PCI_AUTO
 	help
 	  This is used if you know your ATAPI Devices are going to fail DMA
 	  Transfers.
@@ -769,6 +753,14 @@ config BLK_DEV_TC86C001
 	help
 	This driver adds support for Toshiba TC86C001 GOKU-S chip.
 
+config BLK_DEV_CELLEB
+	tristate "Toshiba's Cell Reference Set IDE support"
+	depends on PPC_CELLEB
+	help
+	  This driver provides support for the built-in IDE controller on
+	  Toshiba Cell Reference Board.
+	  If unsure, say Y.
+
 endif
 
 config BLK_DEV_IDE_PMAC
@@ -800,14 +792,6 @@ config BLK_DEV_IDEDMA_PMAC
 	  to transfer data to and from memory.  Saying Y is safe and improves
 	  performance.
 
-config BLK_DEV_IDE_CELLEB
-	bool "Toshiba's Cell Reference Set IDE support"
-	depends on PPC_CELLEB && IDE=y
-	help
-	  This driver provides support for the built-in IDE controller on
-	  Toshiba Cell Reference Board.
-	  If unsure, say Y.
-
 config BLK_DEV_IDE_SWARM
 	tristate "IDE for Sibyte evaluation boards"
 	depends on SIBYTE_SB1xxx_SOC
@@ -851,19 +835,6 @@ config BLK_DEV_IDEDMA_ICS
 	  Say Y here if you want to add DMA (Direct Memory Access) support to
 	  the ICS IDE driver.
 
-config IDEDMA_ICS_AUTO
-	bool "Use ICS DMA by default"
-	depends on BLK_DEV_IDEDMA_ICS
-	help
-	  Prior to kernel version 2.1.112, Linux used to automatically use
-	  DMA for IDE drives and chipsets which support it. Due to concerns
-	  about a couple of cases where buggy hardware may have caused damage,
-	  the default is now to NOT use DMA automatically. To revert to the
-	  previous behaviour, say Y to this question.
-
-	  If you suspect your hardware is at all flakey, say N here.
-	  Do NOT email the IDE kernel people regarding this issue!
-
 config BLK_DEV_IDE_RAPIDE
 	tristate "RapIDE interface support"
 	depends on ARM && ARCH_ACORN
@@ -1086,9 +1057,6 @@ config IDEDMA_IVB
 
 	  It is normally safe to answer Y; however, the default is N.
 
-config IDEDMA_AUTO
-	def_bool IDEDMA_PCI_AUTO || IDEDMA_ICS_AUTO
-
 endif
 
 config BLK_DEV_HD_ONLY
diff --git a/drivers/ide/Makefile b/drivers/ide/Makefile
index 28feedfbd21d..d9f029e8ff74 100644
--- a/drivers/ide/Makefile
+++ b/drivers/ide/Makefile
@@ -37,7 +37,6 @@ ide-core-$(CONFIG_BLK_DEV_Q40IDE)	+= legacy/q40ide.o
 # built-in only drivers from ppc/
 ide-core-$(CONFIG_BLK_DEV_MPC8xx_IDE)	+= ppc/mpc8xx.o
 ide-core-$(CONFIG_BLK_DEV_IDE_PMAC)	+= ppc/pmac.o
-ide-core-$(CONFIG_BLK_DEV_IDE_CELLEB)	+= ppc/scc_pata.o
 
 # built-in only drivers from h8300/
 ide-core-$(CONFIG_H8300)		+= h8300/ide-h8300.o
diff --git a/drivers/ide/arm/icside.c b/drivers/ide/arm/icside.c
index 40e5c66b81ce..e2953fc1fafb 100644
--- a/drivers/ide/arm/icside.c
+++ b/drivers/ide/arm/icside.c
@@ -196,11 +196,6 @@ static void icside_maskproc(ide_drive_t *drive, int mask)
 }
 
 #ifdef CONFIG_BLK_DEV_IDEDMA_ICS
-
-#ifndef CONFIG_IDEDMA_ICS_AUTO
-#warning CONFIG_IDEDMA_ICS_AUTO=n support is obsolete, and will be removed soon.
-#endif
-
 /*
  * SG-DMA support.
  *
@@ -474,12 +469,6 @@ static int icside_dma_lostirq(ide_drive_t *drive)
 
 static void icside_dma_init(ide_hwif_t *hwif)
 {
-	int autodma = 0;
-
-#ifdef CONFIG_IDEDMA_ICS_AUTO
-	autodma = 1;
-#endif
-
 	printk("    %s: SG-DMA", hwif->name);
 
 	hwif->atapi_dma		= 1;
@@ -489,7 +478,7 @@ static void icside_dma_init(ide_hwif_t *hwif)
 	hwif->dmatable_cpu	= NULL;
 	hwif->dmatable_dma	= 0;
 	hwif->speedproc		= icside_set_speed;
-	hwif->autodma		= autodma;
+	hwif->autodma		= 1;
 
 	hwif->ide_dma_check	= icside_dma_check;
 	hwif->dma_host_off	= icside_dma_host_off;
diff --git a/drivers/ide/ide-dma.c b/drivers/ide/ide-dma.c
index 08e7cd043bcc..fd213088b06b 100644
--- a/drivers/ide/ide-dma.c
+++ b/drivers/ide/ide-dma.c
@@ -767,7 +767,7 @@ int ide_set_dma(ide_drive_t *drive)
 	switch(rc) {
 	case -1: /* DMA needs to be disabled */
 		hwif->dma_off_quietly(drive);
-		return 0;
+		return -1;
 	case  0: /* DMA needs to be enabled */
 		return hwif->ide_dma_on(drive);
 	case  1: /* DMA setting cannot be changed */
diff --git a/drivers/ide/ide.c b/drivers/ide/ide.c
index dfbd74458522..695610f0e3e4 100644
--- a/drivers/ide/ide.c
+++ b/drivers/ide/ide.c
@@ -177,11 +177,7 @@ DECLARE_MUTEX(ide_cfg_sem);
 static int ide_scan_direction; /* THIS was formerly 2.2.x pci=reverse */
 #endif
 
-#ifdef CONFIG_IDEDMA_AUTO
 int noautodma = 0;
-#else
-int noautodma = 1;
-#endif
 
 EXPORT_SYMBOL(noautodma);
 
diff --git a/drivers/ide/mips/au1xxx-ide.c b/drivers/ide/mips/au1xxx-ide.c
index b2dc028dc8ca..d54d9fe92a7d 100644
--- a/drivers/ide/mips/au1xxx-ide.c
+++ b/drivers/ide/mips/au1xxx-ide.c
@@ -639,6 +639,7 @@ static int au_ide_probe(struct device *dev)
 	_auide_hwif *ahwif = &auide_hwif;
 	ide_hwif_t *hwif;
 	struct resource *res;
+	hw_regs_t *hw;
 	int ret = 0;
 
 #if defined(CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA)
@@ -681,7 +682,7 @@ static int au_ide_probe(struct device *dev)
 	/* FIXME:  This might possibly break PCMCIA IDE devices */
 
 	hwif                            = &ide_hwifs[pdev->id];
-	hw_regs_t *hw 			= &hwif->hw;
+	hw 				= &hwif->hw;
 	hwif->irq = hw->irq             = ahwif->irq;
 	hwif->chipset                   = ide_au1xxx;
 
diff --git a/drivers/ide/pci/Makefile b/drivers/ide/pci/Makefile
index 6591ff4753cb..95d1ea8f1f14 100644
--- a/drivers/ide/pci/Makefile
+++ b/drivers/ide/pci/Makefile
@@ -3,6 +3,7 @@ obj-$(CONFIG_BLK_DEV_AEC62XX)		+= aec62xx.o
 obj-$(CONFIG_BLK_DEV_ALI15X3)		+= alim15x3.o
 obj-$(CONFIG_BLK_DEV_AMD74XX)		+= amd74xx.o
 obj-$(CONFIG_BLK_DEV_ATIIXP)		+= atiixp.o
+obj-$(CONFIG_BLK_DEV_CELLEB)		+= scc_pata.o
 obj-$(CONFIG_BLK_DEV_CMD64X)		+= cmd64x.o
 obj-$(CONFIG_BLK_DEV_CS5520)		+= cs5520.o
 obj-$(CONFIG_BLK_DEV_CS5530)		+= cs5530.o
diff --git a/drivers/ide/pci/cmd64x.c b/drivers/ide/pci/cmd64x.c
index b0d4825c56a9..561197f7b5bb 100644
--- a/drivers/ide/pci/cmd64x.c
+++ b/drivers/ide/pci/cmd64x.c
@@ -1,6 +1,6 @@
 /* $Id: cmd64x.c,v 1.21 2000/01/30 23:23:16
  *
- * linux/drivers/ide/pci/cmd64x.c		Version 1.41	Feb 3, 2007
+ * linux/drivers/ide/pci/cmd64x.c		Version 1.42	Feb 8, 2007
  *
  * cmd64x.c: Enable interrupts at initialization time on Ultra/PCI machines.
  *           Note, this driver is not used at all on other systems because
@@ -189,6 +189,11 @@ static int cmd64x_get_info (char *buffer, char **addr, off_t offset, int count)
 
 #endif	/* defined(DISPLAY_CMD64X_TIMINGS) && defined(CONFIG_PROC_FS) */
 
+static u8 quantize_timing(int timing, int quant)
+{
+	return (timing + quant - 1) / quant;
+}
+
 /*
  * This routine writes the prepared setup/active/recovery counts
  * for a drive into the cmd646 chipset registers to active them.
@@ -268,47 +273,37 @@ static void program_drive_counts (ide_drive_t *drive, int setup_count, int activ
  */
 static u8 cmd64x_tune_pio (ide_drive_t *drive, u8 mode_wanted)
 {
-	int setup_time, active_time, recovery_time;
-	int clock_time, pio_mode, cycle_time;
-	u8 recovery_count2, cycle_count;
-	int setup_count, active_count, recovery_count;
-	int bus_speed = system_bus_clock();
-	ide_pio_data_t  d;
+	int setup_time, active_time, cycle_time;
+	u8  cycle_count, setup_count, active_count, recovery_count;
+	u8  pio_mode;
+	int clock_time = 1000 / system_bus_clock();
+	ide_pio_data_t pio;
 
-	pio_mode = ide_get_best_pio_mode(drive, mode_wanted, 5, &d);
-	cycle_time = d.cycle_time;
+	pio_mode = ide_get_best_pio_mode(drive, mode_wanted, 5, &pio);
+	cycle_time = pio.cycle_time;
 
-	/*
-	 * I copied all this complicated stuff from cmd640.c and made a few
-	 * minor changes.  For now I am just going to pray that it is correct.
-	 */
 	setup_time  = ide_pio_timings[pio_mode].setup_time;
 	active_time = ide_pio_timings[pio_mode].active_time;
-	recovery_time = cycle_time - (setup_time + active_time);
-	clock_time = 1000 / bus_speed;
-	cycle_count = (cycle_time + clock_time - 1) / clock_time;
-
-	setup_count = (setup_time + clock_time - 1) / clock_time;
 
-	active_count = (active_time + clock_time - 1) / clock_time;
+	setup_count  = quantize_timing( setup_time, clock_time);
+	cycle_count  = quantize_timing( cycle_time, clock_time);
+	active_count = quantize_timing(active_time, clock_time);
 
-	recovery_count = (recovery_time + clock_time - 1) / clock_time;
-	recovery_count2 = cycle_count - (setup_count + active_count);
-	if (recovery_count2 > recovery_count)
-		recovery_count = recovery_count2;
+	recovery_count = cycle_count - active_count;
+	/* program_drive_counts() takes care of zero recovery cycles */
 	if (recovery_count > 16) {
 		active_count += recovery_count - 16;
 		recovery_count = 16;
 	}
 	if (active_count > 16)
-		active_count = 16; /* maximum allowed by cmd646 */
+		active_count = 16; /* maximum allowed by cmd64x */
 
 	program_drive_counts (drive, setup_count, active_count, recovery_count);
 
 	cmdprintk("%s: PIO mode wanted %d, selected %d (%dns)%s, "
 		"clocks=%d/%d/%d\n",
 		drive->name, mode_wanted, pio_mode, cycle_time,
-		d.overridden ? " (overriding vendor mode)" : "",
+		pio.overridden ? " (overriding vendor mode)" : "",
 		setup_count, active_count, recovery_count);
 
 	return pio_mode;
diff --git a/drivers/ide/pci/jmicron.c b/drivers/ide/pci/jmicron.c
index 53f25500c22b..be4fc96c29e0 100644
--- a/drivers/ide/pci/jmicron.c
+++ b/drivers/ide/pci/jmicron.c
@@ -240,12 +240,31 @@ static int __devinit jmicron_init_one(struct pci_dev *dev, const struct pci_devi
 	return 0;
 }
 
+/* If libata is configured, jmicron PCI quirk will configure it such
+ * that the SATA ports are in AHCI function while the PATA ports are
+ * in a separate IDE function.  In such cases, match device class and
+ * attach only to IDE.  If libata isn't configured, keep the old
+ * behavior for backward compatibility.
+ */
+#if defined(CONFIG_ATA) || defined(CONFIG_ATA_MODULE)
+#define JMB_CLASS	PCI_CLASS_STORAGE_IDE << 8
+#define JMB_CLASS_MASK	0xffff00
+#else
+#define JMB_CLASS	0
+#define JMB_CLASS_MASK	0
+#endif
+
 static struct pci_device_id jmicron_pci_tbl[] = {
-	{ PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
-	{ PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
-	{ PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
-	{ PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3},
-	{ PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4},
+	{ PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361,
+	  PCI_ANY_ID, PCI_ANY_ID, JMB_CLASS, JMB_CLASS_MASK, 0},
+	{ PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363,
+	  PCI_ANY_ID, PCI_ANY_ID, JMB_CLASS, JMB_CLASS_MASK, 1},
+	{ PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365,
+	  PCI_ANY_ID, PCI_ANY_ID, JMB_CLASS, JMB_CLASS_MASK, 2},
+	{ PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366,
+	  PCI_ANY_ID, PCI_ANY_ID, JMB_CLASS, JMB_CLASS_MASK, 3},
+	{ PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368,
+	  PCI_ANY_ID, PCI_ANY_ID, JMB_CLASS, JMB_CLASS_MASK, 4},
 	{ 0, },
 };
 
diff --git a/drivers/ide/ppc/scc_pata.c b/drivers/ide/pci/scc_pata.c
index f84bf791f72e..f84bf791f72e 100644
--- a/drivers/ide/ppc/scc_pata.c
+++ b/drivers/ide/pci/scc_pata.c
diff --git a/drivers/ide/setup-pci.c b/drivers/ide/setup-pci.c
index a52c80fe7d3e..118fb3205ca8 100644
--- a/drivers/ide/setup-pci.c
+++ b/drivers/ide/setup-pci.c
@@ -505,11 +505,6 @@ static void ide_hwif_setup_dma(struct pci_dev *dev, ide_pci_device_t *d, ide_hwi
 		}
 	}
 }
-
-#ifndef CONFIG_IDEDMA_PCI_AUTO
-#warning CONFIG_IDEDMA_PCI_AUTO=n support is obsolete, and will be removed soon.
-#endif
-
 #endif /* CONFIG_BLK_DEV_IDEDMA_PCI*/
 
 /**
diff --git a/include/asm-mips/mach-au1x00/au1xxx_ide.h b/include/asm-mips/mach-au1x00/au1xxx_ide.h
index e9fa252f8a3f..8fcae21adbd5 100644
--- a/include/asm-mips/mach-au1x00/au1xxx_ide.h
+++ b/include/asm-mips/mach-au1x00/au1xxx_ide.h
@@ -141,40 +141,6 @@ static int auide_ddma_init( _auide_hwif *auide );
 static void auide_setup_ports(hw_regs_t *hw, _auide_hwif *ahwif);
 int __init auide_probe(void);
 
-#ifdef CONFIG_PM
-        int au1200ide_pm_callback( au1xxx_power_dev_t *dev,
-                                   au1xxx_request_t request, void *data);
-        static int au1xxxide_pm_standby( au1xxx_power_dev_t *dev );
-        static int au1xxxide_pm_sleep( au1xxx_power_dev_t *dev );
-        static int au1xxxide_pm_resume( au1xxx_power_dev_t *dev );
-        static int au1xxxide_pm_getstatus( au1xxx_power_dev_t *dev );
-        static int au1xxxide_pm_access( au1xxx_power_dev_t *dev );
-        static int au1xxxide_pm_idle( au1xxx_power_dev_t *dev );
-        static int au1xxxide_pm_cleanup( au1xxx_power_dev_t *dev );
-#endif
-
-
-/*
- * Multi-Word DMA + DbDMA functions
- */
-#ifdef CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
-        static int auide_build_sglist(ide_drive_t *drive,  struct request *rq);
-        static int auide_build_dmatable(ide_drive_t *drive);
-        static int auide_dma_end(ide_drive_t *drive);
-        ide_startstop_t auide_dma_intr (ide_drive_t *drive);
-        static void auide_dma_exec_cmd(ide_drive_t *drive, u8 command);
-        static int auide_dma_setup(ide_drive_t *drive);
-        static int auide_dma_check(ide_drive_t *drive);
-        static int auide_dma_test_irq(ide_drive_t *drive);
-        static int auide_dma_host_off(ide_drive_t *drive);
-        static int auide_dma_host_on(ide_drive_t *drive);
-        static int auide_dma_lostirq(ide_drive_t *drive);
-        static int auide_dma_on(ide_drive_t *drive);
-        static void auide_ddma_tx_callback(int irq, void *param);
-        static void auide_ddma_rx_callback(int irq, void *param);
-        static int auide_dma_off_quietly(ide_drive_t *drive);
-#endif /* end CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA */
-
 /*******************************************************************************
 * PIO Mode timing calculation :                                                *
 *                                                                              *