ARM: sun7i: hummingbird: Convert to DT label based syntax

In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

1 files changed, 181 insertions, 183 deletions

diff --git a/arch/arm/boot/dts/sun7i-a20-hummingbird.dts b/arch/arm/boot/dts/sun7i-a20-hummingbird.dts
index 2a9ee72b2b4a..8c30e126abe6 100644
--- a/arch/arm/boot/dts/sun7i-a20-hummingbird.dts
+++ b/arch/arm/boot/dts/sun7i-a20-hummingbird.dts
@@ -67,218 +67,216 @@
 		serial4 = &uart5;
 	};
 
-	soc@01c00000 {
-		mmc0: mmc@01c0f000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
-			vmmc-supply = <&reg_vcc3v0>;
-			bus-width = <4>;
-			cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
-			cd-inverted;
-			status = "okay";
-		};
+	reg_mmc3_vdd: mmc3_vdd {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&mmc3_vdd_pin_a20_hummingbird>;
+		regulator-name = "mmc3_vdd";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		enable-active-high;
+		gpio = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
+	};
 
-		mmc3: mmc@01c12000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&mmc3_pins_a>;
-			vmmc-supply = <&reg_mmc3_vdd>;
-			bus-width = <4>;
-			non-removable;
-			status = "okay";
-		};
+	reg_gmac_vdd: gmac_vdd {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gmac_vdd_pin_a20_hummingbird>;
+		regulator-name = "gmac_vdd";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		enable-active-high;
+		gpio = <&pio 7 16 GPIO_ACTIVE_HIGH>; /* PH16 */
+	};
+};
 
-		usbphy: phy@01c13400 {
-			usb1_vbus-supply = <&reg_usb1_vbus>;
-			usb2_vbus-supply = <&reg_usb2_vbus>;
-			status = "okay";
-		};
+&ahci {
+	target-supply = <&reg_ahci_5v>;
+	status = "okay";
+};
 
-		ehci0: usb@01c14000 {
-			status = "okay";
-		};
+&ehci0 {
+	status = "okay";
+};
 
-		ohci0: usb@01c14400 {
-			status = "okay";
-		};
+&ehci1 {
+	status = "okay";
+};
 
-		ahci: sata@01c18000 {
-			target-supply = <&reg_ahci_5v>;
-			status = "okay";
-		};
+&gmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac_pins_rgmii_a>;
+	phy = <&phy1>;
+	phy-mode = "rgmii";
+	phy-supply = <&reg_gmac_vdd>;
+	/* phy reset config */
+	snps,reset-gpio = <&pio 0 17 GPIO_ACTIVE_HIGH>; /* PA17 */
+	snps,reset-active-low;
+	/* wait 1s after reset, otherwise fail to read phy id */
+	snps,reset-delays-us = <0 10000 1000000>;
+	status = "okay";
 
-		ehci1: usb@01c1c000 {
-			status = "okay";
-		};
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
 
-		ohci1: usb@01c1c400 {
-			status = "okay";
-		};
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
 
-		pio: pinctrl@01c20800 {
-			ahci_pwr_pin_a20_hummingbird: ahci_pwr_pin@0 {
-				allwinner,pins = "PH15";
-				allwinner,function = "gpio_out";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
+	axp209: pmic@34 {
+		compatible = "x-powers,axp209";
+		reg = <0x34>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+};
 
-			usb1_vbus_pin_a20_hummingbird: usb1_vbus_pin@0 {
-				allwinner,pins = "PH2";
-				allwinner,function = "gpio_out";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_a>;
+	status = "okay";
+};
 
-			mmc3_vdd_pin_a20_hummingbird: mmc3_vdd_pin@0 {
-				allwinner,pins = "PH9";
-				allwinner,function = "gpio_out";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	status = "okay";
+};
 
-			gmac_vdd_pin_a20_hummingbird: gmac_vdd_pin@0 {
-				allwinner,pins = "PH16";
-				allwinner,function = "gpio_out";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-		};
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins_a>;
+	status = "okay";
+};
 
-		pwm: pwm@01c20e00 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&pwm0_pins_a>;
-			status = "okay";
-		};
+&ir0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ir0_pins_a>;
+	status = "okay";
+};
 
-		ir0: ir@01c21800 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&ir0_pins_a>;
-			status = "okay";
-		};
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+	vmmc-supply = <&reg_vcc3v0>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+	cd-inverted;
+	status = "okay";
+};
 
-		uart0: serial@01c28000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&uart0_pins_a>;
-			status = "okay";
-		};
+&mmc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc3_pins_a>;
+	vmmc-supply = <&reg_mmc3_vdd>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
 
-		uart2: serial@01c28800 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&uart2_pins_a>;
-			status = "okay";
-		};
+&ohci0 {
+	status = "okay";
+};
 
-		uart3: serial@01c28c00 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&uart3_pins_a>;
-			status = "okay";
-		};
+&ohci1 {
+	status = "okay";
+};
 
-		uart4: serial@01c29000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&uart4_pins_a>;
-			status = "okay";
-		};
+&pio {
+	ahci_pwr_pin_a20_hummingbird: ahci_pwr_pin@0 {
+		allwinner,pins = "PH15";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
 
-		uart5: serial@01c29400 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&uart5_pins_a>;
-			status = "okay";
-		};
+	usb1_vbus_pin_a20_hummingbird: usb1_vbus_pin@0 {
+		allwinner,pins = "PH2";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
 
-		i2c0: i2c@01c2ac00 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c0_pins_a>;
-			status = "okay";
+	mmc3_vdd_pin_a20_hummingbird: mmc3_vdd_pin@0 {
+		allwinner,pins = "PH9";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
 
-			axp209: pmic@34 {
-				compatible = "x-powers,axp209";
-				reg = <0x34>;
-				interrupt-parent = <&nmi_intc>;
-				interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-				interrupt-controller;
-				#interrupt-cells = <1>;
-			};
-		};
+	gmac_vdd_pin_a20_hummingbird: gmac_vdd_pin@0 {
+		allwinner,pins = "PH16";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+};
 
-		i2c1: i2c@01c2b000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c1_pins_a>;
-			status = "okay";
-		};
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pins_a>;
+	status = "okay";
+};
 
-		i2c2: i2c@01c2b400 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c2_pins_a>;
-			status = "okay";
-		};
+&reg_ahci_5v {
+	pinctrl-0 = <&ahci_pwr_pin_a20_hummingbird>;
+	gpio = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
+	status = "okay";
+};
 
-		i2c3: i2c@01c2b800 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c3_pins_a>;
-			status = "okay";
-		};
+&reg_usb1_vbus {
+	pinctrl-0 = <&usb1_vbus_pin_a20_hummingbird>;
+	gpio = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
+	status = "okay";
+};
 
-		spi2: spi@01c17000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&spi2_pins_b>;
-			status = "okay";
-		};
+&reg_usb2_vbus {
+	status = "okay";
+};
 
-		gmac: ethernet@01c50000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&gmac_pins_rgmii_a>;
-			phy = <&phy1>;
-			phy-mode = "rgmii";
-			phy-supply = <&reg_gmac_vdd>;
-			/* phy reset config */
-			snps,reset-gpio = <&pio 0 17 GPIO_ACTIVE_HIGH>; /* PA17 */
-			snps,reset-active-low;
-			/* wait 1s after reset, otherwise fail to read phy id */
-			snps,reset-delays-us = <0 10000 1000000>;
-			status = "okay";
+&spi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_b>;
+	status = "okay";
+};
 
-			phy1: ethernet-phy@1 {
-				reg = <1>;
-			};
-		};
-	};
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
 
-	reg_ahci_5v: ahci-5v {
-		pinctrl-0 = <&ahci_pwr_pin_a20_hummingbird>;
-		gpio = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
-		status = "okay";
-	};
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins_a>;
+	status = "okay";
+};
 
-	reg_usb1_vbus: usb1-vbus {
-		pinctrl-0 = <&usb1_vbus_pin_a20_hummingbird>;
-		gpio = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
-		status = "okay";
-	};
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins_a>;
+	status = "okay";
+};
 
-	reg_usb2_vbus: usb2-vbus {
-		status = "okay";
-	};
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_a>;
+	status = "okay";
+};
 
-	reg_mmc3_vdd: mmc3_vdd {
-		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&mmc3_vdd_pin_a20_hummingbird>;
-		regulator-name = "mmc3_vdd";
-		regulator-min-microvolt = <3000000>;
-		regulator-max-microvolt = <3000000>;
-		enable-active-high;
-		gpio = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
-	};
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart5_pins_a>;
+	status = "okay";
+};
 
-	reg_gmac_vdd: gmac_vdd {
-		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&gmac_vdd_pin_a20_hummingbird>;
-		regulator-name = "gmac_vdd";
-		regulator-min-microvolt = <3000000>;
-		regulator-max-microvolt = <3000000>;
-		enable-active-high;
-		gpio = <&pio 7 16 GPIO_ACTIVE_HIGH>; /* PH16 */
-	};
+&usbphy {
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	usb2_vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
 };