Merge branch 'Phylink-integration-improvements-for-Felix-DSA-driver'

Vladimir Oltean says:

====================
Phylink integration improvements for Felix DSA driver

This is an overhaul of the Felix switch driver's phylink operations.

Patches 1, 3, 4 and 5 are cleanup, patch 2 is adding a new feature and
and patch 6 is adaptation to the new format of an existing phylink API
(mac_link_up).

Changes since v2:
- Replaced "PHYLINK" with "phylink".
- Rewrote commit message of patch 5/6.

Changes since v1:
- Now using phy_clear_bits and phy_set_bits instead of plain writes to
  MII_BMCR. This combines former patches 1/7 and 6/7 into a single new
  patch 1/6.
- Updated commit message of patch 5/6.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

4 files changed, 211 insertions, 203 deletions

diff --git a/drivers/net/dsa/ocelot/felix.c b/drivers/net/dsa/ocelot/felix.c
index 75020af7f7a4..75652ed99b24 100644
--- a/drivers/net/dsa/ocelot/felix.c
+++ b/drivers/net/dsa/ocelot/felix.c
@@ -194,13 +194,15 @@ static void felix_phylink_validate(struct dsa_switch *ds, int port,
 		return;
 	}
 
-	/* No half-duplex. */
 	phylink_set_port_modes(mask);
 	phylink_set(mask, Autoneg);
 	phylink_set(mask, Pause);
 	phylink_set(mask, Asym_Pause);
+	phylink_set(mask, 10baseT_Half);
 	phylink_set(mask, 10baseT_Full);
+	phylink_set(mask, 100baseT_Half);
 	phylink_set(mask, 100baseT_Full);
+	phylink_set(mask, 1000baseT_Half);
 	phylink_set(mask, 1000baseT_Full);
 
 	if (state->interface == PHY_INTERFACE_MODE_INTERNAL ||
@@ -233,50 +235,10 @@ static void felix_phylink_mac_config(struct dsa_switch *ds, int port,
 				     const struct phylink_link_state *state)
 {
 	struct ocelot *ocelot = ds->priv;
-	struct ocelot_port *ocelot_port = ocelot->ports[port];
-	struct felix *felix = ocelot_to_felix(ocelot);
-	u32 mac_fc_cfg;
-
-	/* Take port out of reset by clearing the MAC_TX_RST, MAC_RX_RST and
-	 * PORT_RST bits in CLOCK_CFG
-	 */
-	ocelot_port_writel(ocelot_port, DEV_CLOCK_CFG_LINK_SPEED(state->speed),
-			   DEV_CLOCK_CFG);
-
-	/* Flow control. Link speed is only used here to evaluate the time
-	 * specification in incoming pause frames.
-	 */
-	mac_fc_cfg = SYS_MAC_FC_CFG_FC_LINK_SPEED(state->speed);
-
-	/* handle Rx pause in all cases, with 2500base-X this is used for rate
-	 * adaptation.
-	 */
-	mac_fc_cfg |= SYS_MAC_FC_CFG_RX_FC_ENA;
-
-	if (state->pause & MLO_PAUSE_TX)
-		mac_fc_cfg |= SYS_MAC_FC_CFG_TX_FC_ENA |
-			      SYS_MAC_FC_CFG_PAUSE_VAL_CFG(0xffff) |
-			      SYS_MAC_FC_CFG_FC_LATENCY_CFG(0x7) |
-			      SYS_MAC_FC_CFG_ZERO_PAUSE_ENA;
-	ocelot_write_rix(ocelot, mac_fc_cfg, SYS_MAC_FC_CFG, port);
-
-	ocelot_write_rix(ocelot, 0, ANA_POL_FLOWC, port);
-
-	if (felix->info->pcs_init)
-		felix->info->pcs_init(ocelot, port, link_an_mode, state);
-
-	if (felix->info->port_sched_speed_set)
-		felix->info->port_sched_speed_set(ocelot, port,
-						  state->speed);
-}
-
-static void felix_phylink_mac_an_restart(struct dsa_switch *ds, int port)
-{
-	struct ocelot *ocelot = ds->priv;
 	struct felix *felix = ocelot_to_felix(ocelot);
 
-	if (felix->info->pcs_an_restart)
-		felix->info->pcs_an_restart(ocelot, port);
+	if (felix->info->pcs_config)
+		felix->info->pcs_config(ocelot, port, link_an_mode, state);
 }
 
 static void felix_phylink_mac_link_down(struct dsa_switch *ds, int port,
@@ -300,8 +262,58 @@ static void felix_phylink_mac_link_up(struct dsa_switch *ds, int port,
 {
 	struct ocelot *ocelot = ds->priv;
 	struct ocelot_port *ocelot_port = ocelot->ports[port];
+	struct felix *felix = ocelot_to_felix(ocelot);
+	u32 mac_fc_cfg;
+
+	/* Take port out of reset by clearing the MAC_TX_RST, MAC_RX_RST and
+	 * PORT_RST bits in DEV_CLOCK_CFG. Note that the way this system is
+	 * integrated is that the MAC speed is fixed and it's the PCS who is
+	 * performing the rate adaptation, so we have to write "1000Mbps" into
+	 * the LINK_SPEED field of DEV_CLOCK_CFG (which is also its default
+	 * value).
+	 */
+	ocelot_port_writel(ocelot_port,
+			   DEV_CLOCK_CFG_LINK_SPEED(OCELOT_SPEED_1000),
+			   DEV_CLOCK_CFG);
+
+	switch (speed) {
+	case SPEED_10:
+		mac_fc_cfg = SYS_MAC_FC_CFG_FC_LINK_SPEED(3);
+		break;
+	case SPEED_100:
+		mac_fc_cfg = SYS_MAC_FC_CFG_FC_LINK_SPEED(2);
+		break;
+	case SPEED_1000:
+	case SPEED_2500:
+		mac_fc_cfg = SYS_MAC_FC_CFG_FC_LINK_SPEED(1);
+		break;
+	default:
+		dev_err(ocelot->dev, "Unsupported speed on port %d: %d\n",
+			port, speed);
+		return;
+	}
+
+	/* handle Rx pause in all cases, with 2500base-X this is used for rate
+	 * adaptation.
+	 */
+	mac_fc_cfg |= SYS_MAC_FC_CFG_RX_FC_ENA;
+
+	if (tx_pause)
+		mac_fc_cfg |= SYS_MAC_FC_CFG_TX_FC_ENA |
+			      SYS_MAC_FC_CFG_PAUSE_VAL_CFG(0xffff) |
+			      SYS_MAC_FC_CFG_FC_LATENCY_CFG(0x7) |
+			      SYS_MAC_FC_CFG_ZERO_PAUSE_ENA;
 
-	/* Enable MAC module */
+	/* Flow control. Link speed is only used here to evaluate the time
+	 * specification in incoming pause frames.
+	 */
+	ocelot_write_rix(ocelot, mac_fc_cfg, SYS_MAC_FC_CFG, port);
+
+	ocelot_write_rix(ocelot, 0, ANA_POL_FLOWC, port);
+
+	/* Undo the effects of felix_phylink_mac_link_down:
+	 * enable MAC module
+	 */
 	ocelot_port_writel(ocelot_port, DEV_MAC_ENA_CFG_RX_ENA |
 			   DEV_MAC_ENA_CFG_TX_ENA, DEV_MAC_ENA_CFG);
 
@@ -318,6 +330,13 @@ static void felix_phylink_mac_link_up(struct dsa_switch *ds, int port,
 			 QSYS_SWITCH_PORT_MODE_SCH_NEXT_CFG(1) |
 			 QSYS_SWITCH_PORT_MODE_PORT_ENA,
 			 QSYS_SWITCH_PORT_MODE, port);
+
+	if (felix->info->pcs_link_up)
+		felix->info->pcs_link_up(ocelot, port, link_an_mode, interface,
+					 speed, duplex);
+
+	if (felix->info->port_sched_speed_set)
+		felix->info->port_sched_speed_set(ocelot, port, speed);
 }
 
 static void felix_port_qos_map_init(struct ocelot *ocelot, int port)
@@ -784,7 +803,6 @@ static const struct dsa_switch_ops felix_switch_ops = {
 	.phylink_validate	= felix_phylink_validate,
 	.phylink_mac_link_state	= felix_phylink_mac_pcs_get_state,
 	.phylink_mac_config	= felix_phylink_mac_config,
-	.phylink_mac_an_restart	= felix_phylink_mac_an_restart,
 	.phylink_mac_link_down	= felix_phylink_mac_link_down,
 	.phylink_mac_link_up	= felix_phylink_mac_link_up,
 	.port_enable		= felix_port_enable,
diff --git a/drivers/net/dsa/ocelot/felix.h b/drivers/net/dsa/ocelot/felix.h
index a891736ca006..00137b64132b 100644
--- a/drivers/net/dsa/ocelot/felix.h
+++ b/drivers/net/dsa/ocelot/felix.h
@@ -28,10 +28,13 @@ struct felix_info {
 	int				imdio_pci_bar;
 	int	(*mdio_bus_alloc)(struct ocelot *ocelot);
 	void	(*mdio_bus_free)(struct ocelot *ocelot);
-	void	(*pcs_init)(struct ocelot *ocelot, int port,
-			    unsigned int link_an_mode,
-			    const struct phylink_link_state *state);
-	void	(*pcs_an_restart)(struct ocelot *ocelot, int port);
+	void	(*pcs_config)(struct ocelot *ocelot, int port,
+			      unsigned int link_an_mode,
+			      const struct phylink_link_state *state);
+	void	(*pcs_link_up)(struct ocelot *ocelot, int port,
+			       unsigned int link_an_mode,
+			       phy_interface_t interface,
+			       int speed, int duplex);
 	void	(*pcs_link_state)(struct ocelot *ocelot, int port,
 				  struct phylink_link_state *state);
 	int	(*prevalidate_phy_mode)(struct ocelot *ocelot, int port,
diff --git a/drivers/net/dsa/ocelot/felix_vsc9959.c b/drivers/net/dsa/ocelot/felix_vsc9959.c
index 2067776773f7..19614537b1ba 100644
--- a/drivers/net/dsa/ocelot/felix_vsc9959.c
+++ b/drivers/net/dsa/ocelot/felix_vsc9959.c
@@ -728,42 +728,6 @@ static int vsc9959_reset(struct ocelot *ocelot)
 	return 0;
 }
 
-static void vsc9959_pcs_an_restart_sgmii(struct phy_device *pcs)
-{
-	phy_set_bits(pcs, MII_BMCR, BMCR_ANRESTART);
-}
-
-static void vsc9959_pcs_an_restart_usxgmii(struct phy_device *pcs)
-{
-	phy_write_mmd(pcs, MDIO_MMD_VEND2, MII_BMCR,
-		      USXGMII_BMCR_RESET |
-		      USXGMII_BMCR_AN_EN |
-		      USXGMII_BMCR_RST_AN);
-}
-
-static void vsc9959_pcs_an_restart(struct ocelot *ocelot, int port)
-{
-	struct felix *felix = ocelot_to_felix(ocelot);
-	struct phy_device *pcs = felix->pcs[port];
-
-	if (!pcs)
-		return;
-
-	switch (pcs->interface) {
-	case PHY_INTERFACE_MODE_SGMII:
-	case PHY_INTERFACE_MODE_QSGMII:
-		vsc9959_pcs_an_restart_sgmii(pcs);
-		break;
-	case PHY_INTERFACE_MODE_USXGMII:
-		vsc9959_pcs_an_restart_usxgmii(pcs);
-		break;
-	default:
-		dev_err(ocelot->dev, "Invalid PCS interface type %s\n",
-			phy_modes(pcs->interface));
-		break;
-	}
-}
-
 /* We enable SGMII AN only when the PHY has managed = "in-band-status" in the
  * device tree. If we are in MLO_AN_PHY mode, we program directly state->speed
  * into the PCS, which is retrieved out-of-band over MDIO. This also has the
@@ -773,129 +737,54 @@ static void vsc9959_pcs_an_restart(struct ocelot *ocelot, int port)
  * traffic if SGMII AN is enabled but not completed (acknowledged by us), so
  * setting MLO_AN_INBAND is actually required for those.
  */
-static void vsc9959_pcs_init_sgmii(struct phy_device *pcs,
-				   unsigned int link_an_mode,
-				   const struct phylink_link_state *state)
+static void vsc9959_pcs_config_sgmii(struct phy_device *pcs,
+				     unsigned int link_an_mode,
+				     const struct phylink_link_state *state)
 {
-	if (link_an_mode == MLO_AN_INBAND) {
-		int bmsr, bmcr;
-
-		/* Some PHYs like VSC8234 don't like it when AN restarts on
-		 * their system  side and they restart line side AN too, going
-		 * into an endless link up/down loop.  Don't restart PCS AN if
-		 * link is up already.
-		 * We do check that AN is enabled just in case this is the 1st
-		 * call, PCS detects a carrier but AN is disabled from power on
-		 * or by boot loader.
-		 */
-		bmcr = phy_read(pcs, MII_BMCR);
-		if (bmcr < 0)
-			return;
-
-		bmsr = phy_read(pcs, MII_BMSR);
-		if (bmsr < 0)
-			return;
+	int bmsr, bmcr;
 
-		if ((bmcr & BMCR_ANENABLE) && (bmsr & BMSR_LSTATUS))
-			return;
-
-		/* SGMII spec requires tx_config_Reg[15:0] to be exactly 0x4001
-		 * for the MAC PCS in order to acknowledge the AN.
-		 */
-		phy_write(pcs, MII_ADVERTISE, ADVERTISE_SGMII |
-					      ADVERTISE_LPACK);
+	/* Some PHYs like VSC8234 don't like it when AN restarts on
+	 * their system  side and they restart line side AN too, going
+	 * into an endless link up/down loop.  Don't restart PCS AN if
+	 * link is up already.
+	 * We do check that AN is enabled just in case this is the 1st
+	 * call, PCS detects a carrier but AN is disabled from power on
+	 * or by boot loader.
+	 */
+	bmcr = phy_read(pcs, MII_BMCR);
+	if (bmcr < 0)
+		return;
 
-		phy_write(pcs, ENETC_PCS_IF_MODE,
-			  ENETC_PCS_IF_MODE_SGMII_EN |
-			  ENETC_PCS_IF_MODE_USE_SGMII_AN);
+	bmsr = phy_read(pcs, MII_BMSR);
+	if (bmsr < 0)
+		return;
 
-		/* Adjust link timer for SGMII */
-		phy_write(pcs, ENETC_PCS_LINK_TIMER1,
-			  ENETC_PCS_LINK_TIMER1_VAL);
-		phy_write(pcs, ENETC_PCS_LINK_TIMER2,
-			  ENETC_PCS_LINK_TIMER2_VAL);
+	if ((bmcr & BMCR_ANENABLE) && (bmsr & BMSR_LSTATUS))
+		return;
 
-		phy_write(pcs, MII_BMCR, BMCR_ANRESTART | BMCR_ANENABLE);
-	} else {
-		int speed;
+	/* SGMII spec requires tx_config_Reg[15:0] to be exactly 0x4001
+	 * for the MAC PCS in order to acknowledge the AN.
+	 */
+	phy_write(pcs, MII_ADVERTISE, ADVERTISE_SGMII |
+				      ADVERTISE_LPACK);
 
-		if (state->duplex == DUPLEX_HALF) {
-			phydev_err(pcs, "Half duplex not supported\n");
-			return;
-		}
-		switch (state->speed) {
-		case SPEED_1000:
-			speed = ENETC_PCS_SPEED_1000;
-			break;
-		case SPEED_100:
-			speed = ENETC_PCS_SPEED_100;
-			break;
-		case SPEED_10:
-			speed = ENETC_PCS_SPEED_10;
-			break;
-		case SPEED_UNKNOWN:
-			/* Silently don't do anything */
-			return;
-		default:
-			phydev_err(pcs, "Invalid PCS speed %d\n", state->speed);
-			return;
-		}
+	phy_write(pcs, ENETC_PCS_IF_MODE,
+		  ENETC_PCS_IF_MODE_SGMII_EN |
+		  ENETC_PCS_IF_MODE_USE_SGMII_AN);
 
-		phy_write(pcs, ENETC_PCS_IF_MODE,
-			  ENETC_PCS_IF_MODE_SGMII_EN |
-			  ENETC_PCS_IF_MODE_SGMII_SPEED(speed));
+	/* Adjust link timer for SGMII */
+	phy_write(pcs, ENETC_PCS_LINK_TIMER1,
+		  ENETC_PCS_LINK_TIMER1_VAL);
+	phy_write(pcs, ENETC_PCS_LINK_TIMER2,
+		  ENETC_PCS_LINK_TIMER2_VAL);
 
-		/* Yes, not a mistake: speed is given by IF_MODE. */
-		phy_write(pcs, MII_BMCR, BMCR_RESET |
-					 BMCR_SPEED1000 |
-					 BMCR_FULLDPLX);
-	}
+	phy_set_bits(pcs, MII_BMCR, BMCR_ANENABLE);
 }
 
-/* 2500Base-X is SerDes protocol 7 on Felix and 6 on ENETC. It is a SerDes lane
- * clocked at 3.125 GHz which encodes symbols with 8b/10b and does not have
- * auto-negotiation of any link parameters. Electrically it is compatible with
- * a single lane of XAUI.
- * The hardware reference manual wants to call this mode SGMII, but it isn't
- * really, since the fundamental features of SGMII:
- * - Downgrading the link speed by duplicating symbols
- * - Auto-negotiation
- * are not there.
- * The speed is configured at 1000 in the IF_MODE and BMCR MDIO registers
- * because the clock frequency is actually given by a PLL configured in the
- * Reset Configuration Word (RCW).
- * Since there is no difference between fixed speed SGMII w/o AN and 802.3z w/o
- * AN, we call this PHY interface type 2500Base-X. In case a PHY negotiates a
- * lower link speed on line side, the system-side interface remains fixed at
- * 2500 Mbps and we do rate adaptation through pause frames.
- */
-static void vsc9959_pcs_init_2500basex(struct phy_device *pcs,
+static void vsc9959_pcs_config_usxgmii(struct phy_device *pcs,
 				       unsigned int link_an_mode,
 				       const struct phylink_link_state *state)
 {
-	if (link_an_mode == MLO_AN_INBAND) {
-		phydev_err(pcs, "AN not supported on 3.125GHz SerDes lane\n");
-		return;
-	}
-
-	phy_write(pcs, ENETC_PCS_IF_MODE,
-		  ENETC_PCS_IF_MODE_SGMII_EN |
-		  ENETC_PCS_IF_MODE_SGMII_SPEED(ENETC_PCS_SPEED_2500));
-
-	phy_write(pcs, MII_BMCR, BMCR_SPEED1000 |
-				 BMCR_FULLDPLX |
-				 BMCR_RESET);
-}
-
-static void vsc9959_pcs_init_usxgmii(struct phy_device *pcs,
-				     unsigned int link_an_mode,
-				     const struct phylink_link_state *state)
-{
-	if (link_an_mode != MLO_AN_INBAND) {
-		phydev_err(pcs, "USXGMII only supports in-band AN for now\n");
-		return;
-	}
-
 	/* Configure device ability for the USXGMII Replicator */
 	phy_write_mmd(pcs, MDIO_MMD_VEND2, MII_ADVERTISE,
 		      USXGMII_ADVERTISE_SPEED(USXGMII_SPEED_2500) |
@@ -905,9 +794,9 @@ static void vsc9959_pcs_init_usxgmii(struct phy_device *pcs,
 		      USXGMII_ADVERTISE_FDX);
 }
 
-static void vsc9959_pcs_init(struct ocelot *ocelot, int port,
-			     unsigned int link_an_mode,
-			     const struct phylink_link_state *state)
+static void vsc9959_pcs_config(struct ocelot *ocelot, int port,
+			       unsigned int link_an_mode,
+			       const struct phylink_link_state *state)
 {
 	struct felix *felix = ocelot_to_felix(ocelot);
 	struct phy_device *pcs = felix->pcs[port];
@@ -924,8 +813,11 @@ static void vsc9959_pcs_init(struct ocelot *ocelot, int port,
 	linkmode_set_bit_array(phy_basic_ports_array,
 			       ARRAY_SIZE(phy_basic_ports_array),
 			       pcs->supported);
+	linkmode_set_bit(ETHTOOL_LINK_MODE_10baseT_Half_BIT, pcs->supported);
 	linkmode_set_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT, pcs->supported);
+	linkmode_set_bit(ETHTOOL_LINK_MODE_100baseT_Half_BIT, pcs->supported);
 	linkmode_set_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT, pcs->supported);
+	linkmode_set_bit(ETHTOOL_LINK_MODE_1000baseT_Half_BIT, pcs->supported);
 	linkmode_set_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT, pcs->supported);
 	if (pcs->interface == PHY_INTERFACE_MODE_2500BASEX ||
 	    pcs->interface == PHY_INTERFACE_MODE_USXGMII)
@@ -936,16 +828,110 @@ static void vsc9959_pcs_init(struct ocelot *ocelot, int port,
 				 pcs->supported);
 	phy_advertise_supported(pcs);
 
+	if (!phylink_autoneg_inband(link_an_mode))
+		return;
+
 	switch (pcs->interface) {
 	case PHY_INTERFACE_MODE_SGMII:
 	case PHY_INTERFACE_MODE_QSGMII:
-		vsc9959_pcs_init_sgmii(pcs, link_an_mode, state);
+		vsc9959_pcs_config_sgmii(pcs, link_an_mode, state);
 		break;
 	case PHY_INTERFACE_MODE_2500BASEX:
-		vsc9959_pcs_init_2500basex(pcs, link_an_mode, state);
+		phydev_err(pcs, "AN not supported on 3.125GHz SerDes lane\n");
 		break;
 	case PHY_INTERFACE_MODE_USXGMII:
-		vsc9959_pcs_init_usxgmii(pcs, link_an_mode, state);
+		vsc9959_pcs_config_usxgmii(pcs, link_an_mode, state);
+		break;
+	default:
+		dev_err(ocelot->dev, "Unsupported link mode %s\n",
+			phy_modes(pcs->interface));
+	}
+}
+
+static void vsc9959_pcs_link_up_sgmii(struct phy_device *pcs,
+				      unsigned int link_an_mode,
+				      int speed, int duplex)
+{
+	u16 if_mode = ENETC_PCS_IF_MODE_SGMII_EN;
+
+	switch (speed) {
+	case SPEED_1000:
+		if_mode |= ENETC_PCS_IF_MODE_SGMII_SPEED(ENETC_PCS_SPEED_1000);
+		break;
+	case SPEED_100:
+		if_mode |= ENETC_PCS_IF_MODE_SGMII_SPEED(ENETC_PCS_SPEED_100);
+		break;
+	case SPEED_10:
+		if_mode |= ENETC_PCS_IF_MODE_SGMII_SPEED(ENETC_PCS_SPEED_10);
+		break;
+	default:
+		phydev_err(pcs, "Invalid PCS speed %d\n", speed);
+		return;
+	}
+
+	if (duplex == DUPLEX_HALF)
+		if_mode |= ENETC_PCS_IF_MODE_DUPLEX_HALF;
+
+	phy_write(pcs, ENETC_PCS_IF_MODE, if_mode);
+	phy_clear_bits(pcs, MII_BMCR, BMCR_ANENABLE);
+}
+
+/* 2500Base-X is SerDes protocol 7 on Felix and 6 on ENETC. It is a SerDes lane
+ * clocked at 3.125 GHz which encodes symbols with 8b/10b and does not have
+ * auto-negotiation of any link parameters. Electrically it is compatible with
+ * a single lane of XAUI.
+ * The hardware reference manual wants to call this mode SGMII, but it isn't
+ * really, since the fundamental features of SGMII:
+ * - Downgrading the link speed by duplicating symbols
+ * - Auto-negotiation
+ * are not there.
+ * The speed is configured at 1000 in the IF_MODE and BMCR MDIO registers
+ * because the clock frequency is actually given by a PLL configured in the
+ * Reset Configuration Word (RCW).
+ * Since there is no difference between fixed speed SGMII w/o AN and 802.3z w/o
+ * AN, we call this PHY interface type 2500Base-X. In case a PHY negotiates a
+ * lower link speed on line side, the system-side interface remains fixed at
+ * 2500 Mbps and we do rate adaptation through pause frames.
+ */
+static void vsc9959_pcs_link_up_2500basex(struct phy_device *pcs,
+					  unsigned int link_an_mode,
+					  int speed, int duplex)
+{
+	u16 if_mode = ENETC_PCS_IF_MODE_SGMII_SPEED(ENETC_PCS_SPEED_2500) |
+		      ENETC_PCS_IF_MODE_SGMII_EN;
+
+	if (duplex == DUPLEX_HALF)
+		if_mode |= ENETC_PCS_IF_MODE_DUPLEX_HALF;
+
+	phy_write(pcs, ENETC_PCS_IF_MODE, if_mode);
+	phy_clear_bits(pcs, MII_BMCR, BMCR_ANENABLE);
+}
+
+static void vsc9959_pcs_link_up(struct ocelot *ocelot, int port,
+				unsigned int link_an_mode,
+				phy_interface_t interface,
+				int speed, int duplex)
+{
+	struct felix *felix = ocelot_to_felix(ocelot);
+	struct phy_device *pcs = felix->pcs[port];
+
+	if (!pcs)
+		return;
+
+	if (phylink_autoneg_inband(link_an_mode))
+		return;
+
+	switch (interface) {
+	case PHY_INTERFACE_MODE_SGMII:
+	case PHY_INTERFACE_MODE_QSGMII:
+		vsc9959_pcs_link_up_sgmii(pcs, link_an_mode, speed, duplex);
+		break;
+	case PHY_INTERFACE_MODE_2500BASEX:
+		vsc9959_pcs_link_up_2500basex(pcs, link_an_mode, speed,
+					      duplex);
+		break;
+	case PHY_INTERFACE_MODE_USXGMII:
+		phydev_err(pcs, "USXGMII only supports in-band AN for now\n");
 		break;
 	default:
 		dev_err(ocelot->dev, "Unsupported link mode %s\n",
@@ -1412,8 +1398,8 @@ struct felix_info felix_info_vsc9959 = {
 	.imdio_pci_bar		= 0,
 	.mdio_bus_alloc		= vsc9959_mdio_bus_alloc,
 	.mdio_bus_free		= vsc9959_mdio_bus_free,
-	.pcs_init		= vsc9959_pcs_init,
-	.pcs_an_restart		= vsc9959_pcs_an_restart,
+	.pcs_config		= vsc9959_pcs_config,
+	.pcs_link_up		= vsc9959_pcs_link_up,
 	.pcs_link_state		= vsc9959_pcs_link_state,
 	.prevalidate_phy_mode	= vsc9959_prevalidate_phy_mode,
 	.port_setup_tc          = vsc9959_port_setup_tc,
diff --git a/include/linux/fsl/enetc_mdio.h b/include/linux/fsl/enetc_mdio.h
index 4875dd38af7e..2d9203314865 100644
--- a/include/linux/fsl/enetc_mdio.h
+++ b/include/linux/fsl/enetc_mdio.h
@@ -15,6 +15,7 @@
 #define ENETC_PCS_IF_MODE_SGMII_EN		BIT(0)
 #define ENETC_PCS_IF_MODE_USE_SGMII_AN		BIT(1)
 #define ENETC_PCS_IF_MODE_SGMII_SPEED(x)	(((x) << 2) & GENMASK(3, 2))
+#define ENETC_PCS_IF_MODE_DUPLEX_HALF		BIT(3)
 
 /* Not a mistake, the SerDes PLL needs to be set at 3.125 GHz by Reset
  * Configuration Word (RCW, outside Linux control) for 2.5G SGMII mode. The PCS