Merge tag 'tegra-for-4.20-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt

dt-bindings: Changes for v4.20-rc1

This contains the PMC pad configuration bindings which are used to
control the voltage of various pads found on Tegra chips. Among other
things this is required to enable faster modes on SDHCI.

* tag 'tegra-for-4.20-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  dt-bindings: Add Tegra PMC pad configuration bindings

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

2 files changed, 196 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt
index 5a3bf7c5a7a0..c9fd6d1de57e 100644
--- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt
+++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt
@@ -34,3 +34,96 @@ Board DTS:
 	pmc@c360000 {
 		nvidia,invert-interrupt;
 	};
+
+== Pad Control ==
+
+On Tegra SoCs a pad is a set of pins which are configured as a group.
+The pin grouping is a fixed attribute of the hardware. The PMC can be
+used to set pad power state and signaling voltage. A pad can be either
+in active or power down mode. The support for power state and signaling
+voltage configuration varies depending on the pad in question. 3.3 V and
+1.8 V signaling voltages are supported on pins where software
+controllable signaling voltage switching is available.
+
+Pad configurations are described with pin configuration nodes which
+are placed under the pmc node and they are referred to by the pinctrl
+client properties. For more information see
+Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt.
+
+The following pads are present on Tegra186:
+csia		csib		dsi		mipi-bias
+pex-clk-bias	pex-clk3	pex-clk2	pex-clk1
+usb0		usb1		usb2		usb-bias
+uart		audio		hsic		dbg
+hdmi-dp0	hdmi-dp1	pex-cntrl	sdmmc2-hv
+sdmmc4		cam		dsib		dsic
+dsid		csic		csid		csie
+dsif		spi		ufs		dmic-hv
+edp		sdmmc1-hv	sdmmc3-hv	conn
+audio-hv	ao-hv
+
+Required pin configuration properties:
+  - pins: A list of strings, each of which contains the name of a pad
+	  to be configured.
+
+Optional pin configuration properties:
+  - low-power-enable: Configure the pad into power down mode
+  - low-power-disable: Configure the pad into active mode
+  - power-source: Must contain either TEGRA_IO_PAD_VOLTAGE_1V8 or
+    TEGRA_IO_PAD_VOLTAGE_3V3 to select between signaling voltages.
+    The values are defined in
+    include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h.
+
+Note: The power state can be configured on all of the above pads except
+      for ao-hv. Following pads have software configurable signaling
+      voltages: sdmmc2-hv, dmic-hv, sdmmc1-hv, sdmmc3-hv, audio-hv,
+      ao-hv.
+
+Pad configuration state example:
+	pmc: pmc@7000e400 {
+		compatible = "nvidia,tegra186-pmc";
+		reg = <0 0x0c360000 0 0x10000>,
+		      <0 0x0c370000 0 0x10000>,
+		      <0 0x0c380000 0 0x10000>,
+		      <0 0x0c390000 0 0x10000>;
+		reg-names = "pmc", "wake", "aotag", "scratch";
+
+		...
+
+		sdmmc1_3v3: sdmmc1-3v3 {
+			pins = "sdmmc1-hv";
+			power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>;
+		};
+
+		sdmmc1_1v8: sdmmc1-1v8 {
+			pins = "sdmmc1-hv";
+			power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>;
+		};
+
+		hdmi_off: hdmi-off {
+			pins = "hdmi";
+			low-power-enable;
+		}
+
+		hdmi_on: hdmi-on {
+			pins = "hdmi";
+			low-power-disable;
+		}
+	};
+
+Pinctrl client example:
+	sdmmc1: sdhci@3400000 {
+		...
+		pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
+		pinctrl-0 = <&sdmmc1_3v3>;
+		pinctrl-1 = <&sdmmc1_1v8>;
+	};
+
+	...
+
+	sor0: sor@15540000 {
+		...
+		pinctrl-0 = <&hdmi_off>;
+		pinctrl-1 = <&hdmi_on>;
+		pinctrl-names = "hdmi-on", "hdmi-off";
+	};
diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
index a74b37b07e5c..cb12f33a247f 100644
--- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
+++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
@@ -195,3 +195,106 @@ Example:
 		power-domains = <&pd_audio>;
 		...
 	};
+
+== Pad Control ==
+
+On Tegra SoCs a pad is a set of pins which are configured as a group.
+The pin grouping is a fixed attribute of the hardware. The PMC can be
+used to set pad power state and signaling voltage. A pad can be either
+in active or power down mode. The support for power state and signaling
+voltage configuration varies depending on the pad in question. 3.3 V and
+1.8 V signaling voltages are supported on pins where software
+controllable signaling voltage switching is available.
+
+The pad configuration state nodes are placed under the pmc node and they
+are referred to by the pinctrl client properties. For more information
+see Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt.
+The pad name should be used as the value of the pins property in pin
+configuration nodes.
+
+The following pads are present on Tegra124 and Tegra132:
+audio		bb		cam		comp
+csia		csb		cse		dsi
+dsib		dsic		dsid		hdmi
+hsic		hv		lvds		mipi-bias
+nand		pex-bias	pex-clk1	pex-clk2
+pex-cntrl	sdmmc1		sdmmc3		sdmmc4
+sys_ddc		uart		usb0		usb1
+usb2		usb_bias
+
+The following pads are present on Tegra210:
+audio		audio-hv	cam		csia
+csib		csic		csid		csie
+csif		dbg		debug-nonao	dmic
+dp		dsi		dsib		dsic
+dsid		emmc		emmc2		gpio
+hdmi		hsic		lvds		mipi-bias
+pex-bias	pex-clk1	pex-clk2	pex-cntrl
+sdmmc1		sdmmc3		spi		spi-hv
+uart		usb0		usb1		usb2
+usb3		usb-bias
+
+Required pin configuration properties:
+  - pins: Must contain name of the pad(s) to be configured.
+
+Optional pin configuration properties:
+  - low-power-enable: Configure the pad into power down mode
+  - low-power-disable: Configure the pad into active mode
+  - power-source: Must contain either TEGRA_IO_PAD_VOLTAGE_1V8
+    or TEGRA_IO_PAD_VOLTAGE_3V3 to select between signaling voltages.
+    The values are defined in
+    include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h.
+
+Note: The power state can be configured on all of the Tegra124 and
+      Tegra132 pads. None of the Tegra124 or Tegra132 pads support
+      signaling voltage switching.
+
+Note: All of the listed Tegra210 pads except pex-cntrl support power
+      state configuration. Signaling voltage switching is supported on
+      following Tegra210 pads: audio, audio-hv, cam, dbg, dmic, gpio,
+      pex-cntrl, sdmmc1, sdmmc3, spi, spi-hv, and uart.
+
+Pad configuration state example:
+	pmc: pmc@7000e400 {
+		compatible = "nvidia,tegra210-pmc";
+		reg = <0x0 0x7000e400 0x0 0x400>;
+		clocks = <&tegra_car TEGRA210_CLK_PCLK>, <&clk32k_in>;
+		clock-names = "pclk", "clk32k_in";
+
+		...
+
+		sdmmc1_3v3: sdmmc1-3v3 {
+			pins = "sdmmc1";
+			power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>;
+		};
+
+		sdmmc1_1v8: sdmmc1-1v8 {
+			pins = "sdmmc1";
+			power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>;
+		};
+
+		hdmi_off: hdmi-off {
+			pins = "hdmi";
+			low-power-enable;
+		}
+
+		hdmi_on: hdmi-on {
+			pins = "hdmi";
+			low-power-disable;
+		}
+	};
+
+Pinctrl client example:
+	sdmmc1: sdhci@700b0000 {
+		...
+		pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
+		pinctrl-0 = <&sdmmc1_3v3>;
+		pinctrl-1 = <&sdmmc1_1v8>;
+	};
+	...
+	sor@54540000 {
+		...
+		pinctrl-0 = <&hdmi_off>;
+		pinctrl-1 = <&hdmi_on>;
+		pinctrl-names = "hdmi-on", "hdmi-off";
+	};