Merge branch 'for-3.5' of ../cgroup into block/for-3.5/core-merged

cgroup/for-3.5 contains the following changes which blk-cgroup needs
to proceed with the on-going cleanup.

* Dynamic addition and removal of cftypes to make config/stat file
  handling modular for policies.

* cgroup removal update to not wait for css references to drain to fix
  blkcg removal hang caused by cfq caching cfqgs.

Pull in cgroup/for-3.5 into block/for-3.5/core.  This causes the
following conflicts in block/blk-cgroup.c.

* 761b3ef50e "cgroup: remove cgroup_subsys argument from callbacks"
  conflicts with blkiocg_pre_destroy() addition and blkiocg_attach()
  removal.  Resolved by removing @subsys from all subsys methods.

* 676f7c8f84 "cgroup: relocate cftype and cgroup_subsys definitions in
  controllers" conflicts with ->pre_destroy() and ->attach() updates
  and removal of modular config.  Resolved by dropping forward
  declarations of the methods and applying updates to the relocated
  blkio_subsys.

* 4baf6e3325 "cgroup: convert all non-memcg controllers to the new
  cftype interface" builds upon the previous item.  Resolved by adding
  ->base_cftypes to the relocated blkio_subsys.

Signed-off-by: Tejun Heo <tj@kernel.org>

1 files changed, 34 insertions, 2 deletions

diff --git a/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt b/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt
index eb4b530d64e1..023c9526e5f8 100644
--- a/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt
@@ -1,8 +1,40 @@
-NVIDIA Tegra 2 GPIO controller
+NVIDIA Tegra GPIO controller
 
 Required properties:
-- compatible : "nvidia,tegra20-gpio"
+- compatible : "nvidia,tegra<chip>-gpio"
+- reg : Physical base address and length of the controller's registers.
+- interrupts : The interrupt outputs from the controller. For Tegra20,
+  there should be 7 interrupts specified, and for Tegra30, there should
+  be 8 interrupts specified.
 - #gpio-cells : Should be two. The first cell is the pin number and the
   second cell is used to specify optional parameters:
   - bit 0 specifies polarity (0 for normal, 1 for inverted)
 - gpio-controller : Marks the device node as a GPIO controller.
+- #interrupt-cells : Should be 2.
+  The first cell is the GPIO number.
+  The second cell is used to specify flags:
+    bits[3:0] trigger type and level flags:
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      4 = active high level-sensitive.
+      8 = active low level-sensitive.
+      Valid combinations are 1, 2, 3, 4, 8.
+- interrupt-controller : Marks the device node as an interrupt controller.
+
+Example:
+
+gpio: gpio@6000d000 {
+	compatible = "nvidia,tegra20-gpio";
+	reg = < 0x6000d000 0x1000 >;
+	interrupts = < 0 32 0x04
+		       0 33 0x04
+		       0 34 0x04
+		       0 35 0x04
+		       0 55 0x04
+		       0 87 0x04
+		       0 89 0x04 >;
+	#gpio-cells = <2>;
+	gpio-controller;
+	#interrupt-cells = <2>;
+	interrupt-controller;
+};