dt-bindings: pinctrl: Move mcp23s08 from gpio

The mcp23s08 driver was moved from gpio to pinctrl. This moves it's
devicetree binding doc as well. So driver and binding doc are in sync
again.

Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

1 files changed, 0 insertions, 83 deletions

diff --git a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt
deleted file mode 100644
index c934106b10aa..000000000000
--- a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt
+++ /dev/null
@@ -1,83 +0,0 @@
-Microchip MCP2308/MCP23S08/MCP23017/MCP23S17 driver for
-8-/16-bit I/O expander with serial interface (I2C/SPI)
-
-Required properties:
-- compatible : Should be
-    - "mcp,mcp23s08" (DEPRECATED) for  8 GPIO SPI version
-    - "mcp,mcp23s17" (DEPRECATED) for 16 GPIO SPI version
-    - "mcp,mcp23008" (DEPRECATED) for  8 GPIO I2C version or
-    - "mcp,mcp23017" (DEPRECATED) for 16 GPIO I2C version of the chip
-
-    - "microchip,mcp23s08" for  8 GPIO SPI version
-    - "microchip,mcp23s17" for 16 GPIO SPI version
-    - "microchip,mcp23s18" for 16 GPIO SPI version
-    - "microchip,mcp23008" for  8 GPIO I2C version or
-    - "microchip,mcp23017" for 16 GPIO I2C version of the chip
-    NOTE: Do not use the old mcp prefix any more. It is deprecated and will be
-    removed.
-- #gpio-cells : Should be two.
-  - first cell is the pin number
-  - second cell is used to specify flags. Flags are currently unused.
-- gpio-controller : Marks the device node as a GPIO controller.
-- reg : For an address on its bus. I2C uses this a the I2C address of the chip.
-        SPI uses this to specify the chipselect line which the chip is
-        connected to. The driver and the SPI variant of the chip support
-        multiple chips on the same chipselect. Have a look at
-        microchip,spi-present-mask below.
-
-Required device specific properties (only for SPI chips):
-- mcp,spi-present-mask (DEPRECATED)
-- microchip,spi-present-mask : This is a present flag, that makes only sense for SPI
-        chips - as the name suggests. Multiple SPI chips can share the same
-        SPI chipselect. Set a bit in bit0-7 in this mask to 1 if there is a
-        chip connected with the corresponding spi address set. For example if
-        you have a chip with address 3 connected, you have to set bit3 to 1,
-        which is 0x08. mcp23s08 chip variant only supports bits 0-3. It is not
-        possible to mix mcp23s08 and mcp23s17 on the same chipselect. Set at
-        least one bit to 1 for SPI chips.
-    NOTE: Do not use the old mcp prefix any more. It is deprecated and will be
-    removed.
-- spi-max-frequency = The maximum frequency this chip is able to handle
-
-Optional properties:
-- #interrupt-cells : Should be two.
-  - first cell is the pin number
-  - second cell is used to specify flags.
-- interrupt-controller: Marks the device node as a interrupt controller.
-
-Optional device specific properties:
-- microchip,irq-mirror: Sets the mirror flag in the IOCON register. Devices
-        with two interrupt outputs (these are the devices ending with 17 and
-        those that have 16 IOs) have two IO banks: IO 0-7 form bank 1 and
-        IO 8-15 are bank 2. These chips have two different interrupt outputs:
-        One for bank 1 and another for bank 2. If irq-mirror is set, both
-        interrupts are generated regardless of the bank that an input change
-        occurred on. If it is not set, the interrupt are only generated for the
-        bank they belong to.
-        On devices with only one interrupt output this property is useless.
-- microchip,irq-active-high: Sets the INTPOL flag in the IOCON register. This
-        configures the IRQ output polarity as active high.
-
-Example I2C (with interrupt):
-gpiom1: gpio@20 {
-        compatible = "microchip,mcp23017";
-        gpio-controller;
-        #gpio-cells = <2>;
-        reg = <0x20>;
-
-        interrupt-parent = <&gpio1>;
-        interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
-        interrupt-controller;
-        #interrupt-cells=<2>;
-        microchip,irq-mirror;
-};
-
-Example SPI:
-gpiom1: gpio@0 {
-        compatible = "microchip,mcp23s17";
-        gpio-controller;
-        #gpio-cells = <2>;
-        spi-present-mask = <0x01>;
-        reg = <0>;
-        spi-max-frequency = <1000000>;
-};