Merge branch 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux

Pull i2c-embedded changes from Wolfram Sang:
 - CBUS driver (an I2C variant)
 - continued rework of the omap driver
 - s3c2410 gets lots of fixes and gains pinctrl support
 - at91 gains DMA support
 - the GPIO muxer gains devicetree probing
 - typical fixes and additions all over

* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (45 commits)
  i2c: omap: Remove the OMAP_I2C_FLAG_RESET_REGS_POSTIDLE flag
  i2c: at91: add dma support
  i2c: at91: change struct members indentation
  i2c: at91: fix compilation warning
  i2c: mxs: Do not disable the I2C SMBus quick mode
  i2c: mxs: Handle i2c DMA failure properly
  i2c: s3c2410: Remove recently introduced performance overheads
  i2c: ocores: Move grlib set/get functions into #ifdef CONFIG_OF block
  i2c: s3c2410: Add fix for i2c suspend/resume
  i2c: s3c2410: Fix code to free gpios
  i2c: i2c-cbus-gpio: introduce driver
  i2c: ocores: Add support for the GRLIB port of the controller and use function pointers for getreg and setreg functions
  i2c: ocores: Add irq support for sparc
  i2c: omap: Move the remove constraint
  ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049
  i2c: s3c2410: do not special case HDMIPHY stuck bus detection
  i2c: s3c2410: use exponential back off while polling for bus idle
  i2c: s3c2410: do not generate STOP for QUIRK_HDMIPHY
  i2c: s3c2410: grab adapter lock while changing i2c clock
  i2c: s3c2410: Add support for pinctrl
  ...

1 files changed, 16 insertions, 4 deletions

diff --git a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt
index b6cb5a12c672..e9611ace8792 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt
@@ -13,11 +13,17 @@ Required properties:
   - interrupts: interrupt number to the cpu.
   - samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges.
 
+Required for all cases except "samsung,s3c2440-hdmiphy-i2c":
+  - Samsung GPIO variant (deprecated):
+    - gpios: The order of the gpios should be the following: <SDA, SCL>.
+      The gpio specifier depends on the gpio controller. Required in all
+      cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output
+      lines are permanently wired to the respective clienta
+  - Pinctrl variant (preferred, if available):
+    - pinctrl-0: Pin control group to be used for this controller.
+    - pinctrl-names: Should contain only one value - "default".
+
 Optional properties:
-  - gpios: The order of the gpios should be the following: <SDA, SCL>.
-    The gpio specifier depends on the gpio controller. Required in all
-    cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output
-    lines are permanently wired to the respective client
   - samsung,i2c-slave-addr: Slave address in multi-master enviroment. If not
     specified, default value is 0.
   - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not
@@ -31,8 +37,14 @@ Example:
 		interrupts = <345>;
 		samsung,i2c-sda-delay = <100>;
 		samsung,i2c-max-bus-freq = <100000>;
+		/* Samsung GPIO variant begins here */
 		gpios = <&gpd1 2 0 /* SDA */
 			 &gpd1 3 0 /* SCL */>;
+		/* Samsung GPIO variant ends here */
+		/* Pinctrl variant begins here */
+		pinctrl-0 = <&i2c3_bus>;
+		pinctrl-names = "default";
+		/* Pinctrl variant ends here */
 		#address-cells = <1>;
 		#size-cells = <0>;