Merge tag 'mmc-updates-for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc

Pull MMC updates from Chris Ball:
 "MMC highlights for 3.13:

  Core:
   - Improve runtime PM support, remove mmc_{suspend,resume}_host().
   - Add MMC_CAP_RUNTIME_RESUME, for delaying MMC resume until we're
     outside of the resume sequence (in runtime_resume) to decrease
     system resume time.

  Drivers:
   - dw_mmc: Support HS200 mode.
   - sdhci-eshdc-imx: Support SD3.0 SDR clock tuning, DDR on IMX6.
   - sdhci-pci: Add support for Intel Clovertrail and Merrifield"

* tag 'mmc-updates-for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (108 commits)
  mmc: wbsd: Silence compiler warning
  mmc: core: Silence compiler warning in __mmc_switch
  mmc: sh_mmcif: Convert to clk_prepare|unprepare
  mmc: sh_mmcif: Convert to PM macros when defining dev_pm_ops
  mmc: dw_mmc: exynos: Revert the sdr_timing assignment
  mmc: sdhci: Avoid needless loop while handling SDIO interrupts in sdhci_irq
  mmc: core: Add MMC_CAP_RUNTIME_RESUME to resume at runtime_resume
  mmc: core: Improve runtime PM support during suspend/resume for sd/mmc
  mmc: core: Remove redundant mmc_power_up|off at runtime callbacks
  mmc: Don't force card to active state when entering suspend/shutdown
  MIPS: db1235: Don't use MMC_CLKGATE
  mmc: core: Remove deprecated mmc_suspend|resume_host APIs
  mmc: mmci: Move away from using deprecated APIs
  mmc: via-sdmmc: Move away from using deprecated APIs
  mmc: tmio: Move away from using deprecated APIs
  mmc: sh_mmcif: Move away from using deprecated APIs
  mmc: sdricoh_cs: Move away from using deprecated APIs
  mmc: rtsx: Remove redundant suspend and resume callbacks
  mmc: wbsd: Move away from using deprecated APIs
  mmc: pxamci: Remove redundant suspend and resume callbacks
  ...

1 files changed, 9 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
index 066a78b034ca..8f3f13315358 100644
--- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
+++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
@@ -52,6 +52,9 @@ Optional properties:
   is specified and the ciu clock is specified then we'll try to set the ciu
   clock to this at probe time.
 
+* clock-freq-min-max: Minimum and Maximum clock frequency for card output
+  clock(cclk_out). If it's not specified, max is 200MHZ and min is 400KHz by default.
+
 * num-slots: specifies the number of slots supported by the controller.
   The number of physical slots actually used could be equal or less than the
   value specified by num-slots. If this property is not specified, the value
@@ -66,6 +69,10 @@ Optional properties:
 
 * supports-highspeed: Enables support for high speed cards (up to 50MHz)
 
+* caps2-mmc-hs200-1_8v: Supports mmc HS200 SDR 1.8V mode
+
+* caps2-mmc-hs200-1_2v: Supports mmc HS200 SDR 1.2V mode
+
 * broken-cd: as documented in mmc core bindings.
 
 * vmmc-supply: The phandle to the regulator to use for vmmc.  If this is
@@ -93,8 +100,10 @@ board specific portions as listed below.
 
 	dwmmc0@12200000 {
 		clock-frequency = <400000000>;
+		clock-freq-min-max = <400000 200000000>;
 		num-slots = <1>;
 		supports-highspeed;
+		caps2-mmc-hs200-1_8v;
 		broken-cd;
 		fifo-depth = <0x80>;
 		card-detect-delay = <200>;