dt-bindings: mtd: Convert Qcom NANDc binding to YAML

Convert Qcom NANDc devicetree binding to YAML.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210402150128.29128-2-manivannan.sadhasivam@linaro.org

1 files changed, 0 insertions, 142 deletions

diff --git a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
deleted file mode 100644
index 5647913d8837..000000000000
--- a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
+++ /dev/null
@@ -1,142 +0,0 @@
-* Qualcomm NAND controller
-
-Required properties:
-- compatible:		must be one of the following:
-    * "qcom,ipq806x-nand" - for EBI2 NAND controller being used in IPQ806x
-			    SoC and it uses ADM DMA
-    * "qcom,ipq4019-nand" - for QPIC NAND controller v1.4.0 being used in
-                            IPQ4019 SoC and it uses BAM DMA
-    * "qcom,ipq6018-nand" - for QPIC NAND controller v1.5.0 being used in
-                            IPQ6018 SoC and it uses BAM DMA
-    * "qcom,ipq8074-nand" - for QPIC NAND controller v1.5.0 being used in
-                            IPQ8074 SoC and it uses BAM DMA
-    * "qcom,sdx55-nand"   - for QPIC NAND controller v2.0.0 being used in
-                            SDX55 SoC and it uses BAM DMA
-
-- reg:			MMIO address range
-- clocks:		must contain core clock and always on clock
-- clock-names:		must contain "core" for the core clock and "aon" for the
-			always on clock
-
-EBI2 specific properties:
-- dmas:			DMA specifier, consisting of a phandle to the ADM DMA
-			controller node and the channel number to be used for
-			NAND. Refer to dma.txt and qcom_adm.txt for more details
-- dma-names:		must be "rxtx"
-- qcom,cmd-crci:	must contain the ADM command type CRCI block instance
-			number specified for the NAND controller on the given
-			platform
-- qcom,data-crci:	must contain the ADM data type CRCI block instance
-			number specified for the NAND controller on the given
-			platform
-
-QPIC specific properties:
-- dmas:			DMA specifier, consisting of a phandle to the BAM DMA
-			and the channel number to be used for NAND. Refer to
-			dma.txt, qcom_bam_dma.txt for more details
-- dma-names:		must contain all 3 channel names : "tx", "rx", "cmd"
-- #address-cells:	<1> - subnodes give the chip-select number
-- #size-cells:		<0>
-
-* NAND chip-select
-
-Each controller may contain one or more subnodes to represent enabled
-chip-selects which (may) contain NAND flash chips. Their properties are as
-follows.
-
-Required properties:
-- reg:			a single integer representing the chip-select
-			number (e.g., 0, 1, 2, etc.)
-- #address-cells:	see partition.txt
-- #size-cells:		see partition.txt
-
-Optional properties:
-- nand-bus-width:	see nand-controller.yaml
-- nand-ecc-strength:	see nand-controller.yaml. If not specified, then ECC strength will
-			be used according to chip requirement and available
-			OOB size.
-
-Each nandcs device node may optionally contain a 'partitions' sub-node, which
-further contains sub-nodes describing the flash partition mapping. See
-partition.txt for more detail.
-
-Example:
-
-nand-controller@1ac00000 {
-	compatible = "qcom,ipq806x-nand";
-	reg = <0x1ac00000 0x800>;
-
-	clocks = <&gcc EBI2_CLK>,
-		 <&gcc EBI2_AON_CLK>;
-	clock-names = "core", "aon";
-
-	dmas = <&adm_dma 3>;
-	dma-names = "rxtx";
-	qcom,cmd-crci = <15>;
-	qcom,data-crci = <3>;
-
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	nand@0 {
-		reg = <0>;
-
-		nand-ecc-strength = <4>;
-		nand-bus-width = <8>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			partition@0 {
-				label = "boot-nand";
-				reg = <0 0x58a0000>;
-			};
-
-			partition@58a0000 {
-				label = "fs-nand";
-				reg = <0x58a0000 0x4000000>;
-			};
-		};
-	};
-};
-
-nand-controller@79b0000 {
-	compatible = "qcom,ipq4019-nand";
-	reg = <0x79b0000 0x1000>;
-
-	clocks = <&gcc GCC_QPIC_CLK>,
-		<&gcc GCC_QPIC_AHB_CLK>;
-	clock-names = "core", "aon";
-
-	dmas = <&qpicbam 0>,
-		<&qpicbam 1>,
-		<&qpicbam 2>;
-	dma-names = "tx", "rx", "cmd";
-
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	nand@0 {
-		reg = <0>;
-		nand-ecc-strength = <4>;
-		nand-bus-width = <8>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			partition@0 {
-				label = "boot-nand";
-				reg = <0 0x58a0000>;
-			};
-
-			partition@58a0000 {
-				label = "fs-nand";
-				reg = <0x58a0000 0x4000000>;
-			};
-		};
-	};
-};