Merge remote branch 'intel/drm-intel-next' of ../drm-next into drm-core-next

* 'intel/drm-intel-next' of ../drm-next: (755 commits)
  drm/i915: Only wait on a pending flip if we intend to write to the buffer
  drm/i915/dp: Sanity check eDP existence
  drm/i915: Rebind the buffer if its alignment constraints changes with tiling
  drm/i915: Disable GPU semaphores by default
  drm/i915: Do not overflow the MMADDR write FIFO
  Revert "drm/i915: fix corruptions on i8xx due to relaxed fencing"
  drm/i915: Don't save/restore hardware status page address register
  drm/i915: don't store the reg value for HWS_PGA
  drm/i915: fix memory corruption with GM965 and >4GB RAM
  Linux 2.6.38-rc7
  Revert "TPM: Long default timeout fix"
  drm/i915: Re-enable GPU semaphores for SandyBridge mobile
  drm/i915: Replace vblank PM QoS with "Interrupt-Based AGPBUSY#"
  Revert "drm/i915: Use PM QoS to prevent C-State starvation of gen3 GPU"
  drm/i915: Allow relocation deltas outside of target bo
  drm/i915: Silence an innocuous compiler warning for an unused variable
  fs/block_dev.c: fix new kernel-doc warning
  ACPI: Fix build for CONFIG_NET unset
  mm: <asm-generic/pgtable.h> must include <linux/mm_types.h>
  x86: Use u32 instead of long to set reset vector back to 0
  ...

Conflicts:
	drivers/gpu/drm/i915/i915_gem.c

1 files changed, 144 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/powerpc/fsl/dma.txt b/Documentation/devicetree/bindings/powerpc/fsl/dma.txt
new file mode 100644
index 000000000000..2a4b4bce6110
--- /dev/null
+++ b/Documentation/devicetree/bindings/powerpc/fsl/dma.txt
@@ -0,0 +1,144 @@
+* Freescale 83xx DMA Controller
+
+Freescale PowerPC 83xx have on chip general purpose DMA controllers.
+
+Required properties:
+
+- compatible        : compatible list, contains 2 entries, first is
+		 "fsl,CHIP-dma", where CHIP is the processor
+		 (mpc8349, mpc8360, etc.) and the second is
+		 "fsl,elo-dma"
+- reg               : <registers mapping for DMA general status reg>
+- ranges		: Should be defined as specified in 1) to describe the
+		  DMA controller channels.
+- cell-index        : controller index.  0 for controller @ 0x8100
+- interrupts        : <interrupt mapping for DMA IRQ>
+- interrupt-parent  : optional, if needed for interrupt mapping
+
+
+- DMA channel nodes:
+        - compatible        : compatible list, contains 2 entries, first is
+			 "fsl,CHIP-dma-channel", where CHIP is the processor
+			 (mpc8349, mpc8350, etc.) and the second is
+			 "fsl,elo-dma-channel". However, see note below.
+        - reg               : <registers mapping for channel>
+        - cell-index        : dma channel index starts at 0.
+
+Optional properties:
+        - interrupts        : <interrupt mapping for DMA channel IRQ>
+			  (on 83xx this is expected to be identical to
+			   the interrupts property of the parent node)
+        - interrupt-parent  : optional, if needed for interrupt mapping
+
+Example:
+	dma@82a8 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "fsl,mpc8349-dma", "fsl,elo-dma";
+		reg = <0x82a8 4>;
+		ranges = <0 0x8100 0x1a4>;
+		interrupt-parent = <&ipic>;
+		interrupts = <71 8>;
+		cell-index = <0>;
+		dma-channel@0 {
+			compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+			cell-index = <0>;
+			reg = <0 0x80>;
+			interrupt-parent = <&ipic>;
+			interrupts = <71 8>;
+		};
+		dma-channel@80 {
+			compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+			cell-index = <1>;
+			reg = <0x80 0x80>;
+			interrupt-parent = <&ipic>;
+			interrupts = <71 8>;
+		};
+		dma-channel@100 {
+			compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+			cell-index = <2>;
+			reg = <0x100 0x80>;
+			interrupt-parent = <&ipic>;
+			interrupts = <71 8>;
+		};
+		dma-channel@180 {
+			compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+			cell-index = <3>;
+			reg = <0x180 0x80>;
+			interrupt-parent = <&ipic>;
+			interrupts = <71 8>;
+		};
+	};
+
+* Freescale 85xx/86xx DMA Controller
+
+Freescale PowerPC 85xx/86xx have on chip general purpose DMA controllers.
+
+Required properties:
+
+- compatible        : compatible list, contains 2 entries, first is
+		 "fsl,CHIP-dma", where CHIP is the processor
+		 (mpc8540, mpc8540, etc.) and the second is
+		 "fsl,eloplus-dma"
+- reg               : <registers mapping for DMA general status reg>
+- cell-index        : controller index.  0 for controller @ 0x21000,
+                                         1 for controller @ 0xc000
+- ranges		: Should be defined as specified in 1) to describe the
+		  DMA controller channels.
+
+- DMA channel nodes:
+        - compatible        : compatible list, contains 2 entries, first is
+			 "fsl,CHIP-dma-channel", where CHIP is the processor
+			 (mpc8540, mpc8560, etc.) and the second is
+			 "fsl,eloplus-dma-channel". However, see note below.
+        - cell-index        : dma channel index starts at 0.
+        - reg               : <registers mapping for channel>
+        - interrupts        : <interrupt mapping for DMA channel IRQ>
+        - interrupt-parent  : optional, if needed for interrupt mapping
+
+Example:
+	dma@21300 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma";
+		reg = <0x21300 4>;
+		ranges = <0 0x21100 0x200>;
+		cell-index = <0>;
+		dma-channel@0 {
+			compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
+			reg = <0 0x80>;
+			cell-index = <0>;
+			interrupt-parent = <&mpic>;
+			interrupts = <20 2>;
+		};
+		dma-channel@80 {
+			compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
+			reg = <0x80 0x80>;
+			cell-index = <1>;
+			interrupt-parent = <&mpic>;
+			interrupts = <21 2>;
+		};
+		dma-channel@100 {
+			compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
+			reg = <0x100 0x80>;
+			cell-index = <2>;
+			interrupt-parent = <&mpic>;
+			interrupts = <22 2>;
+		};
+		dma-channel@180 {
+			compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
+			reg = <0x180 0x80>;
+			cell-index = <3>;
+			interrupt-parent = <&mpic>;
+			interrupts = <23 2>;
+		};
+	};
+
+Note on DMA channel compatible properties: The compatible property must say
+"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel" to be used by the Elo DMA
+driver (fsldma).  Any DMA channel used by fsldma cannot be used by another
+DMA driver, such as the SSI sound drivers for the MPC8610.  Therefore, any DMA
+channel that should be used for another driver should not use
+"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel".  For the SSI drivers, for
+example, the compatible property should be "fsl,ssi-dma-channel".  See ssi.txt
+for more information.