Merge tag 'omap-for-v4.1/wl12xx-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Merge "wireless wl12xx and omap device tree changes for v4.1" from Tony
Lindgren:

Wireless and omap changes to make wl12xx driver to use device tree
data instead of platform data from Eliad Peller <eliad@wizery.com>:

- Add device-tree support to the wlcore (wl12xx/wl18xx) driver.

- Update the current users to use the bindings instead of pdata-quirks.

- Finally, remove the deprecated wl12xx_platform_data struct

Note that da850 board file code that still uses the platform data,
but we have da850.dtsi that can be used instead. So it was decided
that we should try to remove the wl12xx support from the da850
board file as suggested by Sekhar Nori <nsekhar@ti.com>. As it's
the last patch in the series, the last patch can be simply reverted
if needed.

As this series touches quite a bit of arch code, it was suggested
by Kalle Valo <kvalo@codeaurora.org> that the whole series should
be merged via the arm-soc tree.

* tag 'omap-for-v4.1/wl12xx-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  wlcore: remove wl12xx_platform_data
  ARM: dts: add wl12xx/wl18xx bindings
  wlcore: add device-tree support
  dt: bindings: add TI's wilink wireless device
  wl12xx: use frequency instead of enumerations for pdata clocks
  wlcore: set irq_trigger in board files instead of hiding behind a quirk
  + Linux 4.0-rc4

Signed-off-by: Olof Johansson <olof@lixom.net>

3 files changed, 35 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/serial/of-serial.txt b/Documentation/devicetree/bindings/serial/8250.txt
index 91d5ab0e60fc..91d5ab0e60fc 100644
--- a/Documentation/devicetree/bindings/serial/of-serial.txt
+++ b/Documentation/devicetree/bindings/serial/8250.txt
diff --git a/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt b/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt
new file mode 100644
index 000000000000..ebcbb62c0a76
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt
@@ -0,0 +1,19 @@
+ETRAX FS UART
+
+Required properties:
+- compatible : "axis,etraxfs-uart"
+- reg: offset and length of the register set for the device.
+- interrupts: device interrupt
+
+Optional properties:
+- {dtr,dsr,ri,cd}-gpios: specify a GPIO for DTR/DSR/RI/CD
+  line respectively.
+
+Example:
+
+serial@b00260000 {
+	compatible = "axis,etraxfs-uart";
+	reg = <0xb0026000 0x1000>;
+	interrupts = <68>;
+	status = "disabled";
+};
diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
index 7f76214f728a..289c40ed7470 100644
--- a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
+++ b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
@@ -21,6 +21,18 @@ Optional properties:
 - reg-io-width : the size (in bytes) of the IO accesses that should be
   performed on the device.  If this property is not present then single byte
   accesses are used.
+- dcd-override : Override the DCD modem status signal. This signal will always
+  be reported as active instead of being obtained from the modem status
+  register. Define this if your serial port does not use this pin.
+- dsr-override : Override the DTS modem status signal. This signal will always
+  be reported as active instead of being obtained from the modem status
+  register. Define this if your serial port does not use this pin.
+- cts-override : Override the CTS modem status signal. This signal will always
+  be reported as active instead of being obtained from the modem status
+  register. Define this if your serial port does not use this pin.
+- ri-override : Override the RI modem status signal. This signal will always be
+  reported as inactive instead of being obtained from the modem status register.
+  Define this if your serial port does not use this pin.
 
 Example:
 
@@ -31,6 +43,10 @@ Example:
 		interrupts = <10>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
+		dcd-override;
+		dsr-override;
+		cts-override;
+		ri-override;
 	};
 
 Example with one clock: