Merge tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull gpio updates from Linus Walleij:
 "This is the big bulk of GPIO changes queued for the v4.2 kernel
  series:

   - a big set of cleanups to the aged sysfs interface from Johan
     Hovold.  To get these in, v4.1-rc3 was merged into the tree as the
     first patch in that series had to go into stable.  This makes the
     locking much more fine-grained (get rid of the "big GPIO lock(s)"
     and store states in the GPIO descriptors.

   - rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value() to
     avoid confusions.

   - New drivers for:
      * NXP LPC18xx (currently LPC1850)
      * NetLogic XLP
      * Broadcom STB SoC's
      * Axis ETRAXFS
      * Zynq Ultrascale+ (subdriver)

   - ACPI:
      * make it possible to retrieve GpioInt resources from a GPIO
        device using acpi_dev_gpio_irq_get()
      * merge some dependent I2C changes exploiting this.
      * support the ARM X-Gene GPIO standby driver.

   - make it possible for the generic GPIO driver to read back the value
     set registers to reflect current status.

   - loads of OMAP IRQ handling fixes.

   - incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
     PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.

   - janitorial (constification, checkpatch cleanups)"

* tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
  gpio: Fix checkpatch.pl issues
  gpio: pcf857x: handle only enabled irqs
  gpio / ACPI: Return -EPROBE_DEFER if the gpiochip was not found
  GPIO / ACPI: export acpi_gpiochip_request(free)_interrupts for module use
  gpio: improve error reporting on own descriptors
  gpio: promote own request failure to pr_err()
  gpio: Added support to Zynq Ultrascale+ MPSoC
  gpio: add ETRAXFS GPIO driver
  fix documentation after renaming gpiod_set_array to gpiod_set_array_value
  gpio: Add GPIO support for Broadcom STB SoCs
  gpio: xgene: add ACPI support for APM X-Gene GPIO standby driver
  gpio: tb10x: Drop unneeded free_irq() call
  gpio: crystalcove: set IRQCHIP_SKIP_SET_WAKE for the irqchip
  gpio: stp-xway: Use the of_property_read_u32 helper
  gpio: pcf857x: Check for irq_set_irq_wake() failures
  gpio-stp-xway: Fix enabling the highest bit of the PHY LEDs
  gpio: Prevent an integer overflow in the pca953x driver
  gpio: omap: rework omap_gpio_irq_startup to handle current pin state properly
  gpio: omap: rework omap_gpio_request to touch only gpio specific registers
  gpio: omap: rework omap_x_irq_shutdown to touch only irqs specific registers
  ...

5 files changed, 173 insertions, 1 deletions

diff --git a/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt b/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt
new file mode 100644
index 000000000000..435f1bcca341
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt
@@ -0,0 +1,65 @@
+Broadcom STB "UPG GIO" GPIO controller
+
+The controller's registers are organized as sets of eight 32-bit
+registers with each set controlling a bank of up to 32 pins.  A single
+interrupt is shared for all of the banks handled by the controller.
+
+Required properties:
+
+- compatible:
+    Must be "brcm,brcmstb-gpio"
+
+- reg:
+    Define the base and range of the I/O address space containing
+    the brcmstb GPIO controller registers
+
+- #gpio-cells:
+    Should be <2>.  The first cell is the pin number (within the controller's
+    pin space), and the second is used for the following:
+    bit[0]: polarity (0 for active-high, 1 for active-low)
+
+- gpio-controller:
+    Specifies that the node is a GPIO controller.
+
+- brcm,gpio-bank-widths:
+    Number of GPIO lines for each bank.  Number of elements must
+    correspond to number of banks suggested by the 'reg' property.
+
+Optional properties:
+
+- interrupts:
+    The interrupt shared by all GPIO lines for this controller.
+
+- interrupt-parent:
+    phandle of the parent interrupt controller
+
+- #interrupt-cells:
+    Should be <2>.  The first cell is the GPIO number, the second should specify
+    flags.  The following subset of flags is supported:
+    - bits[3:0] trigger type and level flags
+        1 = low-to-high edge triggered
+        2 = high-to-low edge triggered
+        4 = active high level-sensitive
+        8 = active low level-sensitive
+      Valid combinations are 1, 2, 3, 4, 8.
+    See also Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+
+- interrupt-controller:
+    Marks the device node as an interrupt controller
+
+- interrupt-names:
+    The name of the IRQ resource used by this controller
+
+Example:
+	upg_gio: gpio@f040a700 {
+		#gpio-cells = <0x2>;
+		#interrupt-cells = <0x2>;
+		compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio";
+		gpio-controller;
+		interrupt-controller;
+		reg = <0xf040a700 0x80>;
+		interrupt-parent = <0xf>;
+		interrupts = <0x6>;
+		interrupt-names = "upg_gio";
+		brcm,gpio-bank-widths = <0x20 0x20 0x20 0x18>;
+	};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-etraxfs.txt b/Documentation/devicetree/bindings/gpio/gpio-etraxfs.txt
new file mode 100644
index 000000000000..abf4db736c6e
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-etraxfs.txt
@@ -0,0 +1,21 @@
+Axis ETRAX FS General I/O controller bindings
+
+Required properties:
+
+- compatible:
+  - "axis,etraxfs-gio"
+- reg: Physical base address and length of the controller's registers.
+- #gpio-cells: Should be 3
+  - The first cell is the gpio offset number.
+  - The second cell is reserved and is currently unused.
+  - The third cell is the port number (hex).
+- gpio-controller: Marks the device node as a GPIO controller.
+
+Example:
+
+	gio: gpio@b001a000 {
+		compatible = "axis,etraxfs-gio";
+		reg = <0xb001a000 0x1000>;
+		gpio-controller;
+		#gpio-cells = <3>;
+	};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-xlp.txt b/Documentation/devicetree/bindings/gpio/gpio-xlp.txt
new file mode 100644
index 000000000000..262ee4ddf2cb
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-xlp.txt
@@ -0,0 +1,47 @@
+Netlogic XLP Family GPIO
+========================
+
+This GPIO driver is used for following Netlogic XLP SoCs:
+	XLP832, XLP316, XLP208, XLP980, XLP532
+
+Required properties:
+-------------------
+
+- compatible: Should be one of the following:
+  - "netlogic,xlp832-gpio": For Netlogic XLP832
+  - "netlogic,xlp316-gpio": For Netlogic XLP316
+  - "netlogic,xlp208-gpio": For Netlogic XLP208
+  - "netlogic,xlp980-gpio": For Netlogic XLP980
+  - "netlogic,xlp532-gpio": For Netlogic XLP532
+- reg: Physical base address and length of the controller's registers.
+- #gpio-cells: Should be two. The first cell is the pin number and the second
+  cell is used to specify optional parameters (currently unused).
+- gpio-controller: Marks the device node as a GPIO controller.
+- nr-gpios: Number of GPIO pins supported by the controller.
+- interrupt-cells: Should be two. The first cell is the GPIO Number. The
+  second cell is used to specify flags. The following subset of flags is
+  supported:
+  - trigger type:
+	1 = low to high edge triggered.
+	2 = high to low edge triggered.
+	4 = active high level-sensitive.
+	8 = active low level-sensitive.
+- interrupts: Interrupt number for this device.
+- interrupt-parent: phandle of the parent interrupt controller.
+- interrupt-controller: Identifies the node as an interrupt controller.
+
+Example:
+
+	gpio: xlp_gpio@34000 {
+		compatible = "netlogic,xlp316-gpio";
+		reg = <0 0x34100 0x1000
+		       0 0x35100 0x1000>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		nr-gpios = <57>;
+
+		#interrupt-cells = <2>;
+		interrupt-parent = <&pic>;
+		interrupts = <39>;
+		interrupt-controller;
+	};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-zynq.txt b/Documentation/devicetree/bindings/gpio/gpio-zynq.txt
index 986371a4be2c..db4c6a663c03 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-zynq.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-zynq.txt
@@ -6,7 +6,7 @@ Required properties:
 			  - First cell is the GPIO line number
 			  - Second cell is used to specify optional
 			    parameters (unused)
-- compatible		: Should be "xlnx,zynq-gpio-1.0"
+- compatible		: Should be "xlnx,zynq-gpio-1.0" or "xlnx,zynqmp-gpio-1.0"
 - clocks		: Clock specifier (see clock bindings for details)
 - gpio-controller	: Marks the device node as a GPIO controller.
 - interrupts		: Interrupt specifier (see interrupt bindings for
diff --git a/Documentation/devicetree/bindings/gpio/nxp,lpc1850-gpio.txt b/Documentation/devicetree/bindings/gpio/nxp,lpc1850-gpio.txt
new file mode 100644
index 000000000000..eb7cdd69e10b
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/nxp,lpc1850-gpio.txt
@@ -0,0 +1,39 @@
+NXP LPC18xx/43xx GPIO controller Device Tree Bindings
+-----------------------------------------------------
+
+Required properties:
+- compatible		: Should be "nxp,lpc1850-gpio"
+- reg			: Address and length of the register set for the device
+- clocks		: Clock specifier (see clock bindings for details)
+- gpio-controller	: Marks the device node as a GPIO controller.
+- #gpio-cells 		: Should be two
+			  - First cell is the GPIO line number
+			  - Second cell is used to specify polarity
+
+Optional properties:
+- gpio-ranges		: Mapping between GPIO and pinctrl
+
+Example:
+#define LPC_GPIO(port, pin)	(port * 32 + pin)
+#define LPC_PIN(port, pin)	(0x##port * 32 + pin)
+
+gpio: gpio@400f4000 {
+	compatible = "nxp,lpc1850-gpio";
+	reg = <0x400f4000 0x4000>;
+	clocks = <&ccu1 CLK_CPU_GPIO>;
+	gpio-controller;
+	#gpio-cells = <2>;
+	gpio-ranges =	<&pinctrl LPC_GPIO(0,0)  LPC_PIN(0,0)  2>,
+			...
+			<&pinctrl LPC_GPIO(7,19) LPC_PIN(f,5)  7>;
+};
+
+gpio_joystick {
+	compatible = "gpio-keys-polled";
+	...
+
+	button@0 {
+		...
+		gpios = <&gpio LPC_GPIO(4,8) GPIO_ACTIVE_LOW>;
+	};
+};