Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

4 files changed, 21 insertions, 5 deletions

diff --git a/Documentation/devicetree/bindings/interrupt-controller/riscv,cpu-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/riscv,cpu-intc.txt
index b0a8af51c388..265b223cd978 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/riscv,cpu-intc.txt
+++ b/Documentation/devicetree/bindings/interrupt-controller/riscv,cpu-intc.txt
@@ -11,7 +11,7 @@ The RISC-V supervisor ISA manual specifies three interrupt sources that are
 attached to every HLIC: software interrupts, the timer interrupt, and external
 interrupts.  Software interrupts are used to send IPIs between cores.  The
 timer interrupt comes from an architecturally mandated real-time timer that is
-controller via Supervisor Binary Interface (SBI) calls and CSR reads.  External
+controlled via Supervisor Binary Interface (SBI) calls and CSR reads.  External
 interrupts connect all other device interrupts to the HLIC, which are routed
 via the platform-level interrupt controller (PLIC).
 
@@ -25,7 +25,15 @@ in the system.
 
 Required properties:
 - compatible : "riscv,cpu-intc"
-- #interrupt-cells : should be <1>
+- #interrupt-cells : should be <1>.  The interrupt sources are defined by the
+  RISC-V supervisor ISA manual, with only the following three interrupts being
+  defined for supervisor mode:
+    - Source 1 is the supervisor software interrupt, which can be sent by an SBI
+      call and is reserved for use by software.
+    - Source 5 is the supervisor timer interrupt, which can be configured by
+      SBI calls and implements a one-shot timer.
+    - Source 9 is the supervisor external interrupt, which chains to all other
+      device interrupts.
 - interrupt-controller : Identifies the node as an interrupt controller
 
 Furthermore, this interrupt-controller MUST be embedded inside the cpu
@@ -38,7 +46,7 @@ An example device tree entry for a HLIC is show below.
 		...
 		cpu1-intc: interrupt-controller {
 			#interrupt-cells = <1>;
-			compatible = "riscv,cpu-intc", "sifive,fu540-c000-cpu-intc";
+			compatible = "sifive,fu540-c000-cpu-intc", "riscv,cpu-intc";
 			interrupt-controller;
 		};
 	};
diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt
index 41089369f891..b3acebe08eb0 100644
--- a/Documentation/devicetree/bindings/net/cpsw.txt
+++ b/Documentation/devicetree/bindings/net/cpsw.txt
@@ -19,6 +19,10 @@ Required properties:
 - slaves		: Specifies number for slaves
 - active_slave		: Specifies the slave to use for time stamping,
 			  ethtool and SIOCGMIIPHY
+- cpsw-phy-sel		: Specifies the phandle to the CPSW phy mode selection
+			  device. See also cpsw-phy-sel.txt for it's binding.
+			  Note that in legacy cases cpsw-phy-sel may be
+			  a child device instead of a phandle.
 
 Optional properties:
 - ti,hwmods		: Must be "cpgmac0"
@@ -75,6 +79,7 @@ Examples:
 		cpts_clock_mult = <0x80000000>;
 		cpts_clock_shift = <29>;
 		syscon = <&cm>;
+		cpsw-phy-sel = <&phy_sel>;
 		cpsw_emac0: slave@0 {
 			phy_id = <&davinci_mdio>, <0>;
 			phy-mode = "rgmii-txid";
@@ -103,6 +108,7 @@ Examples:
 		cpts_clock_mult = <0x80000000>;
 		cpts_clock_shift = <29>;
 		syscon = <&cm>;
+		cpsw-phy-sel = <&phy_sel>;
 		cpsw_emac0: slave@0 {
 			phy_id = <&davinci_mdio>, <0>;
 			phy-mode = "rgmii-txid";
diff --git a/Documentation/devicetree/bindings/net/sh_eth.txt b/Documentation/devicetree/bindings/net/sh_eth.txt
index 76db9f13ad96..abc36274227c 100644
--- a/Documentation/devicetree/bindings/net/sh_eth.txt
+++ b/Documentation/devicetree/bindings/net/sh_eth.txt
@@ -16,6 +16,7 @@ Required properties:
 	      "renesas,ether-r8a7794"  if the device is a part of R8A7794 SoC.
 	      "renesas,gether-r8a77980" if the device is a part of R8A77980 SoC.
 	      "renesas,ether-r7s72100" if the device is a part of R7S72100 SoC.
+	      "renesas,ether-r7s9210" if the device is a part of R7S9210 SoC.
 	      "renesas,rcar-gen1-ether" for a generic R-Car Gen1 device.
 	      "renesas,rcar-gen2-ether" for a generic R-Car Gen2 or RZ/G1
 	                                device.
diff --git a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt
index 5d47a262474c..9407212a85a8 100644
--- a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt
+++ b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt
@@ -7,6 +7,7 @@ Required properties:
 	       Examples with soctypes are:
 		 - "renesas,r8a7743-wdt" (RZ/G1M)
 		 - "renesas,r8a7745-wdt" (RZ/G1E)
+		 - "renesas,r8a774a1-wdt" (RZ/G2M)
 	         - "renesas,r8a7790-wdt" (R-Car H2)
 	         - "renesas,r8a7791-wdt" (R-Car M2-W)
 	         - "renesas,r8a7792-wdt" (R-Car V2H)
@@ -21,8 +22,8 @@ Required properties:
 	         - "renesas,r7s72100-wdt" (RZ/A1)
 		The generic compatible string must be:
 		 - "renesas,rza-wdt" for RZ/A
-		 - "renesas,rcar-gen2-wdt" for R-Car Gen2 and RZ/G
-		 - "renesas,rcar-gen3-wdt" for R-Car Gen3
+		 - "renesas,rcar-gen2-wdt" for R-Car Gen2 and RZ/G1
+		 - "renesas,rcar-gen3-wdt" for R-Car Gen3 and RZ/G2
 
 - reg : Should contain WDT registers location and length
 - clocks : the clock feeding the watchdog timer.