Merge tag 'qcom-cleanup-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into next/cleanup

Merge "qcom cleanup changes for 4.1" from Kumar Gala:

General cleanups for MSM/QCOM for 4.1

* Removal of mach-msm and associated drivers cleanups that have been
  ack'd by associated maintainers

* tag 'qcom-cleanup-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
  mmc: Remove msm_sdcc driver
  gpio: Remove gpio-msm-v1 driver
  ARM: Remove mach-msm and associated ARM architecture code
  + Linux 4.0-rc3

Signed-off-by: Olof Johansson <olof@lixom.net>

3 files changed, 21 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx.txt b/Documentation/devicetree/bindings/i2c/i2c-imx.txt
index 52d37fd8d3e5..ce4311d726ae 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-imx.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-imx.txt
@@ -7,6 +7,7 @@ Required properties:
   - "fsl,vf610-i2c" for I2C compatible with the one integrated on Vybrid vf610 SoC
 - reg : Should contain I2C/HS-I2C registers location and length
 - interrupts : Should contain I2C/HS-I2C interrupt
+- clocks : Should contain the I2C/HS-I2C clock specifier
 
 Optional properties:
 - clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz.
diff --git a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt
index 33df3932168e..8db32384a486 100644
--- a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt
+++ b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt
@@ -27,6 +27,8 @@ property is used.
 - amd,serdes-cdr-rate: CDR rate speed selection
 - amd,serdes-pq-skew: PQ (data sampling) skew
 - amd,serdes-tx-amp: TX amplitude boost
+- amd,serdes-dfe-tap-config: DFE taps available to run
+- amd,serdes-dfe-tap-enable: DFE taps to enable
 
 Example:
 	xgbe_phy@e1240800 {
@@ -41,4 +43,6 @@ Example:
 		amd,serdes-cdr-rate = <2>, <2>, <7>;
 		amd,serdes-pq-skew = <10>, <10>, <30>;
 		amd,serdes-tx-amp = <15>, <15>, <10>;
+		amd,serdes-dfe-tap-config = <3>, <3>, <1>;
+		amd,serdes-dfe-tap-enable = <0>, <0>, <127>;
 	};
diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
index 7f76214f728a..289c40ed7470 100644
--- a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
+++ b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
@@ -21,6 +21,18 @@ Optional properties:
 - reg-io-width : the size (in bytes) of the IO accesses that should be
   performed on the device.  If this property is not present then single byte
   accesses are used.
+- dcd-override : Override the DCD modem status signal. This signal will always
+  be reported as active instead of being obtained from the modem status
+  register. Define this if your serial port does not use this pin.
+- dsr-override : Override the DTS modem status signal. This signal will always
+  be reported as active instead of being obtained from the modem status
+  register. Define this if your serial port does not use this pin.
+- cts-override : Override the CTS modem status signal. This signal will always
+  be reported as active instead of being obtained from the modem status
+  register. Define this if your serial port does not use this pin.
+- ri-override : Override the RI modem status signal. This signal will always be
+  reported as inactive instead of being obtained from the modem status register.
+  Define this if your serial port does not use this pin.
 
 Example:
 
@@ -31,6 +43,10 @@ Example:
 		interrupts = <10>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
+		dcd-override;
+		dsr-override;
+		cts-override;
+		ri-override;
 	};
 
 Example with one clock: