Merge 'net-next/master'

Needed by the upcoming merge of iwlwifi-next-for-kalle-2016-03-02 tag.

15 files changed, 117 insertions, 29 deletions

diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt
index ace05992a262..20df350b9ef3 100644
--- a/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt
+++ b/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt
@@ -30,7 +30,7 @@ that they are defined using standard clock bindings with following
 clock-output-names:
  - "xin24m" - crystal input - required,
  - "ext_i2s" - external I2S clock - optional,
- - "ext_gmac" - external GMAC clock - optional
+ - "rmii_clkin" - external EMAC clock - optional
 
 Example: Clock controller node:
 
diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
index 7803e77d85cb..007a5b46256a 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
+++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
@@ -24,9 +24,8 @@ Main node required properties:
 		1 = edge triggered
 		4 = level triggered
 
-  Cells 4 and beyond are reserved for future use. When the 1st cell
-  has a value of 0 or 1, cells 4 and beyond act as padding, and may be
-  ignored. It is recommended that padding cells have a value of 0.
+  Cells 4 and beyond are reserved for future use and must have a value
+  of 0 if present.
 
 - reg : Specifies base physical address(s) and size of the GIC
   registers, in the following order:
diff --git a/Documentation/devicetree/bindings/net/can/ifi_canfd.txt b/Documentation/devicetree/bindings/net/can/ifi_canfd.txt
new file mode 100644
index 000000000000..20ea5c70ab82
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/can/ifi_canfd.txt
@@ -0,0 +1,15 @@
+IFI CANFD controller
+--------------------
+
+Required properties:
+  - compatible: Should be "ifi,canfd-1.0"
+  - reg: Should contain CAN controller registers location and length
+  - interrupts: Should contain IRQ line for the CAN controller
+
+Example:
+
+	canfd0: canfd@ff220000 {
+		compatible = "ifi,canfd-1.0";
+		reg = <0xff220000 0x00001000>;
+		interrupts = <0 43 0>;
+	};
diff --git a/Documentation/devicetree/bindings/net/can/rcar_can.txt b/Documentation/devicetree/bindings/net/can/rcar_can.txt
index 002d8440bf66..65edc055722f 100644
--- a/Documentation/devicetree/bindings/net/can/rcar_can.txt
+++ b/Documentation/devicetree/bindings/net/can/rcar_can.txt
@@ -6,6 +6,15 @@ Required properties:
 	      "renesas,can-r8a7779" if CAN controller is a part of R8A7779 SoC.
 	      "renesas,can-r8a7790" if CAN controller is a part of R8A7790 SoC.
 	      "renesas,can-r8a7791" if CAN controller is a part of R8A7791 SoC.
+	      "renesas,can-r8a7792" if CAN controller is a part of R8A7792 SoC.
+	      "renesas,can-r8a7793" if CAN controller is a part of R8A7793 SoC.
+	      "renesas,can-r8a7794" if CAN controller is a part of R8A7794 SoC.
+	      "renesas,rcar-gen1-can" for a generic R-Car Gen1 compatible device.
+	      "renesas,rcar-gen2-can" for a generic R-Car Gen2 compatible device.
+	      When compatible with the generic version, nodes must list the
+	      SoC-specific version corresponding to the platform first
+	      followed by the generic version.
+
 - reg: physical base address and size of the R-Car CAN register map.
 - interrupts: interrupt specifier for the sole interrupt.
 - clocks: phandles and clock specifiers for 3 CAN clock inputs.
@@ -25,7 +34,7 @@ Example
 SoC common .dtsi file:
 
 	can0: can@e6e80000 {
-		compatible = "renesas,can-r8a7791";
+		compatible = "renesas,can-r8a7791", "renesas,rcar-gen2-can";
 		reg = <0 0xe6e80000 0 0x1000>;
 		interrupts = <0 186 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7791_CLK_RCAN0>,
diff --git a/Documentation/devicetree/bindings/net/can/sja1000.txt b/Documentation/devicetree/bindings/net/can/sja1000.txt
index b4a6d53fb01a..ac3160eca96a 100644
--- a/Documentation/devicetree/bindings/net/can/sja1000.txt
+++ b/Documentation/devicetree/bindings/net/can/sja1000.txt
@@ -2,7 +2,7 @@ Memory mapped SJA1000 CAN controller from NXP (formerly Philips)
 
 Required properties:
 
-- compatible : should be "nxp,sja1000".
+- compatible : should be one of "nxp,sja1000", "technologic,sja1000".
 
 - reg : should specify the chip select, address offset and size required
 	to map the registers of the SJA1000. The size is usually 0x80.
@@ -14,6 +14,7 @@ Optional properties:
 
 - reg-io-width : Specify the size (in bytes) of the IO accesses that
 	should be performed on the device.  Valid value is 1, 2 or 4.
+	This property is ignored for technologic version.
 	Default to 1 (8 bits).
 
 - nxp,external-clock-frequency : Frequency of the external oscillator
diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt
index c6b1cb5ffa87..b5a42df4c928 100644
--- a/Documentation/devicetree/bindings/net/macb.txt
+++ b/Documentation/devicetree/bindings/net/macb.txt
@@ -25,7 +25,7 @@ Required properties:
 
 Optional properties for PHY child node:
 - reset-gpios : Should specify the gpio for phy reset
-- cdns,magic-packet : If present, indicates that the hardware supports waking
+- magic-packet : If present, indicates that the hardware supports waking
   up via magic packet.
 
 Examples:
diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt
index 81a9f9e6b45f..c8ac222eac67 100644
--- a/Documentation/devicetree/bindings/net/renesas,ravb.txt
+++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt
@@ -82,8 +82,8 @@ Example:
 				  "ch16", "ch17", "ch18", "ch19",
 				  "ch20", "ch21", "ch22", "ch23",
 				  "ch24";
-		clocks = <&mstp8_clks R8A7795_CLK_ETHERAVB>;
-		power-domains = <&cpg_clocks>;
+		clocks = <&cpg CPG_MOD 812>;
+		power-domains = <&cpg>;
 		phy-mode = "rgmii-id";
 		phy-handle = <&phy0>;
 
diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt
index e862a922bd3f..6605d19601c2 100644
--- a/Documentation/devicetree/bindings/net/stmmac.txt
+++ b/Documentation/devicetree/bindings/net/stmmac.txt
@@ -17,7 +17,25 @@ Required properties:
 	The 1st cell is reset pre-delay in micro seconds.
 	The 2nd cell is reset pulse in micro seconds.
 	The 3rd cell is reset post-delay in micro seconds.
+
+Optional properties:
+- resets: Should contain a phandle to the STMMAC reset signal, if any
+- reset-names: Should contain the reset signal name "stmmaceth", if a
+	reset phandle is given
+- max-frame-size: See ethernet.txt file in the same directory
+- clocks: If present, the first clock should be the GMAC main clock and
+  the second clock should be peripheral's register interface clock. Further
+  clocks may be specified in derived bindings.
+- clock-names: One name for each entry in the clocks property, the
+  first one should be "stmmaceth" and the second one should be "pclk".
+- clk_ptp_ref: this is the PTP reference clock; in case of the PTP is
+  available this clock is used for programming the Timestamp Addend Register.
+  If not passed then the system clock will be used and this is fine on some
+  platforms.
+- tx-fifo-depth: See ethernet.txt file in the same directory
+- rx-fifo-depth: See ethernet.txt file in the same directory
 - snps,pbl		Programmable Burst Length
+- snps,aal		Address-Aligned Beats
 - snps,fixed-burst	Program the DMA to use the fixed burst mode
 - snps,mixed-burst	Program the DMA to use the mixed burst mode
 - snps,force_thresh_dma_mode	Force DMA to use the threshold mode for
@@ -29,27 +47,28 @@ Required properties:
 				supported by this device instance
 - snps,perfect-filter-entries:	Number of perfect filter entries supported
 				by this device instance
-
-Optional properties:
-- resets: Should contain a phandle to the STMMAC reset signal, if any
-- reset-names: Should contain the reset signal name "stmmaceth", if a
-	reset phandle is given
-- max-frame-size: See ethernet.txt file in the same directory
-- clocks: If present, the first clock should be the GMAC main clock
-  The optional second clock should be peripheral's register interface clock.
-  The third optional clock should be the ptp reference clock.
-  Further clocks may be specified in derived bindings.
-- clock-names: One name for each entry in the clocks property.
-  The first one should be "stmmaceth".
-  The optional second one should be "pclk".
-  The optional third one should be "clk_ptp_ref".
-- snps,burst_len: The AXI burst lenth value of the AXI BUS MODE register.
-- tx-fifo-depth: See ethernet.txt file in the same directory
-- rx-fifo-depth: See ethernet.txt file in the same directory
+- AXI BUS Mode parameters: below the list of all the parameters to program the
+			   AXI register inside the DMA module:
+	- snps,lpi_en: enable Low Power Interface
+	- snps,xit_frm: unlock on WoL
+	- snps,wr_osr_lmt: max write oustanding req. limit
+	- snps,rd_osr_lmt: max read oustanding req. limit
+	- snps,kbbe: do not cross 1KiB boundary.
+	- snps,axi_all: align address
+	- snps,blen: this is a vector of supported burst length.
+	- snps,fb: fixed-burst
+	- snps,mb: mixed-burst
+	- snps,rb: rebuild INCRx Burst
 - mdio: with compatible = "snps,dwmac-mdio", create and register mdio bus.
 
 Examples:
 
+	stmmac_axi_setup: stmmac-axi-config {
+		snps,wr_osr_lmt = <0xf>;
+		snps,rd_osr_lmt = <0xf>;
+		snps,blen = <256 128 64 32 0 0 0>;
+	};
+
 	gmac0: ethernet@e0800000 {
 		compatible = "st,spear600-gmac";
 		reg = <0xe0800000 0x8000>;
@@ -65,6 +84,7 @@ Examples:
 		tx-fifo-depth = <16384>;
 		clocks = <&clock>;
 		clock-names = "stmmaceth";
+		snps,axi-config = <&stmmac_axi_setup>;
 		mdio0 {
 			#address-cells = <1>;
 			#size-cells = <0>;
diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt
index 4e8b90e43dd8..07a75094c5a8 100644
--- a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt
+++ b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt
@@ -8,6 +8,7 @@ OHCI and EHCI controllers.
 Required properties:
 - compatible: "renesas,pci-r8a7790" for the R8A7790 SoC;
 	      "renesas,pci-r8a7791" for the R8A7791 SoC;
+	      "renesas,pci-r8a7793" for the R8A7793 SoC;
 	      "renesas,pci-r8a7794" for the R8A7794 SoC;
 	      "renesas,pci-rcar-gen2" for a generic R-Car Gen2 compatible device
 
diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt
index 558fe528ae19..6cf99690eef9 100644
--- a/Documentation/devicetree/bindings/pci/rcar-pci.txt
+++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt
@@ -4,6 +4,7 @@ Required properties:
 compatible: "renesas,pcie-r8a7779" for the R8A7779 SoC;
 	    "renesas,pcie-r8a7790" for the R8A7790 SoC;
 	    "renesas,pcie-r8a7791" for the R8A7791 SoC;
+	    "renesas,pcie-r8a7793" for the R8A7793 SoC;
 	    "renesas,pcie-r8a7795" for the R8A7795 SoC;
 	    "renesas,pcie-rcar-gen2" for a generic R-Car Gen2 compatible device.
 
diff --git a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt
index ac2fcd6ff4b8..1068ffce9f91 100644
--- a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt
+++ b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt
@@ -14,6 +14,10 @@ Required properties:
   interrupt number is the rtc alarm interrupt and second interrupt number
   is the rtc tick interrupt. The number of cells representing a interrupt
   depends on the parent interrupt controller.
+- clocks: Must contain a list of phandle and clock specifier for the rtc
+          and source clocks.
+- clock-names: Must contain "rtc" and "rtc_src" entries sorted in the
+               same order as the clocks property.
 
 Example:
 
@@ -21,4 +25,6 @@ Example:
 		compatible = "samsung,s3c6410-rtc";
 		reg = <0x10070000 0x100>;
 		interrupts = <44 0 45 0>;
+		clocks = <&clock CLK_RTC>, <&s2mps11_osc S2MPS11_CLK_AP>;
+		clock-names = "rtc", "rtc_src";
 	};
diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
index 35ae1fb3537f..ed94c217c98d 100644
--- a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
+++ b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
@@ -9,7 +9,7 @@ Optional properties:
 - fsl,uart-has-rtscts : Indicate the uart has rts and cts
 - fsl,irda-mode : Indicate the uart supports irda mode
 - fsl,dte-mode : Indicate the uart works in DTE mode. The uart works
-                  is DCE mode by default.
+                  in DCE mode by default.
 
 Note: Each uart controller should have an alias correctly numbered
 in "aliases" node.
diff --git a/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt b/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt
index ce55c0a6f757..4da41bf1888e 100644
--- a/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt
+++ b/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt
@@ -30,6 +30,8 @@ The compatible list for this generic sound card currently:
  "fsl,imx-audio-sgtl5000"
  (compatible with Documentation/devicetree/bindings/sound/imx-audio-sgtl5000.txt)
 
+ "fsl,imx-audio-wm8960"
+
 Required properties:
 
   - compatible		: Contains one of entries in the compatible list.
diff --git a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt
index 332e625f6ed0..e5ee3f159893 100644
--- a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt
+++ b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt
@@ -1,8 +1,9 @@
 * Renesas R-Car Thermal
 
 Required properties:
-- compatible		: "renesas,thermal-<soctype>", "renesas,rcar-thermal"
-			  as fallback.
+- compatible		: "renesas,thermal-<soctype>",
+			   "renesas,rcar-gen2-thermal" (with thermal-zone) or
+			   "renesas,rcar-thermal" (without thermal-zone) as fallback.
 			  Examples with soctypes are:
 			    - "renesas,thermal-r8a73a4" (R-Mobile APE6)
 			    - "renesas,thermal-r8a7779" (R-Car H1)
@@ -36,3 +37,35 @@ thermal@e61f0000 {
 		0xe61f0300 0x38>;
 	interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
 };
+
+Example (with thermal-zone):
+
+thermal-zones {
+	cpu_thermal: cpu-thermal {
+		polling-delay-passive	= <1000>;
+		polling-delay		= <5000>;
+
+		thermal-sensors = <&thermal>;
+
+		trips {
+			cpu-crit {
+				temperature	= <115000>;
+				hysteresis	= <0>;
+				type		= "critical";
+			};
+		};
+		cooling-maps {
+		};
+	};
+};
+
+thermal: thermal@e61f0000 {
+	compatible =	"renesas,thermal-r8a7790",
+			"renesas,rcar-gen2-thermal",
+			"renesas,rcar-thermal";
+	reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>;
+	interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&mstp5_clks R8A7790_CLK_THERMAL>;
+	power-domains = <&cpg_clocks>;
+	#thermal-sensor-cells = <0>;
+};
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 72e2c5a2b327..c6134dcd2e04 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -111,6 +111,7 @@ hp	Hewlett Packard
 i2se	I2SE GmbH
 ibm	International Business Machines (IBM)
 idt	Integrated Device Technologies, Inc.
+ifi	Ingenieurburo Fur Ic-Technologie (I/F/I)
 iom	Iomega Corporation
 img	Imagination Technologies Ltd.
 ingenic	Ingenic Semiconductor