Merge tag 'dmaengine-5.6-rc1' of git://git.infradead.org/users/vkoul/slave-dma

Pull dmaengine updates from Vinod Koul:
 "This time we have a bunch of core changes to support dynamic channels,
  hotplug of controllers, new apis for metadata ops etc along with new
  drivers for Intel data accelerators, TI K3 UDMA, PLX DMA engine and
  hisilicon Kunpeng DMA engine. Also usual assorted updates to drivers.

  Core:
   - Support for dynamic channels
   - Removal of various slave wrappers
   - Make few slave request APIs as private to dmaengine
   - Symlinks between channels and slaves
   - Support for hotplug of controllers
   - Support for metadata_ops for dma_async_tx_descriptor
   - Reporting DMA cached data amount
   - Virtual dma channel locking updates

  New drivers/device/feature support support:
   - Driver for Intel data accelerators
   - Driver for TI K3 UDMA
   - Driver for PLX DMA engine
   - Driver for hisilicon Kunpeng DMA engine
   - Support for eDMA support for QorIQ LS1028A in fsl edma driver
   - Support for cyclic dma in sun4i driver
   - Support for X1830 in JZ4780 driver"

* tag 'dmaengine-5.6-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (62 commits)
  dmaengine: Create symlinks between DMA channels and slaves
  dmaengine: hisilicon: Add Kunpeng DMA engine support
  dmaengine: idxd: add char driver to expose submission portal to userland
  dmaengine: idxd: connect idxd to dmaengine subsystem
  dmaengine: idxd: add descriptor manipulation routines
  dmaengine: idxd: add sysfs ABI for idxd driver
  dmaengine: idxd: add configuration component of driver
  dmaengine: idxd: Init and probe for Intel data accelerators
  dmaengine: add support to dynamic register/unregister of channels
  dmaengine: break out channel registration
  x86/asm: add iosubmit_cmds512() based on MOVDIR64B CPU instruction
  dmaengine: ti: k3-udma: fix spelling mistake "limted" -> "limited"
  dmaengine: s3c24xx-dma: fix spelling mistake "to" -> "too"
  dmaengine: Move dma_get_{,any_}slave_channel() to private dmaengine.h
  dmaengine: Remove dma_request_slave_channel_compat() wrapper
  dmaengine: Remove dma_device_satisfies_mask() wrapper
  dt-bindings: fsl-imx-sdma: Add i.MX8MM/i.MX8MN/i.MX8MP compatible string
  dmaengine: zynqmp_dma: fix burst length configuration
  dmaengine: sun4i: Add support for cyclic requests with dedicated DMA
  dmaengine: fsl-qdma: fix duplicated argument to &&
  ...

6 files changed, 252 insertions, 2 deletions

diff --git a/Documentation/devicetree/bindings/dma/fsl-edma.txt b/Documentation/devicetree/bindings/dma/fsl-edma.txt
index 29dd3ccb1235..e77b08ebcd06 100644
--- a/Documentation/devicetree/bindings/dma/fsl-edma.txt
+++ b/Documentation/devicetree/bindings/dma/fsl-edma.txt
@@ -10,6 +10,7 @@ Required properties:
 - compatible :
 	- "fsl,vf610-edma" for eDMA used similar to that on Vybrid vf610 SoC
 	- "fsl,imx7ulp-edma" for eDMA2 used similar to that on i.mx7ulp
+	- "fsl,fsl,ls1028a-edma" for eDMA used similar to that on Vybrid vf610 SoC
 - reg : Specifies base physical address(s) and size of the eDMA registers.
 	The 1st region is eDMA control register's address and size.
 	The 2nd and the 3rd regions are programmable channel multiplexing
diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
index 9d8bbac27d8b..c9e97409e853 100644
--- a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
+++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
@@ -10,6 +10,9 @@ Required properties:
       "fsl,imx6q-sdma"
       "fsl,imx7d-sdma"
       "fsl,imx8mq-sdma"
+      "fsl,imx8mm-sdma"
+      "fsl,imx8mn-sdma"
+      "fsl,imx8mp-sdma"
   The -to variants should be preferred since they allow to determine the
   correct ROM script addresses needed for the driver to work without additional
   firmware.
diff --git a/Documentation/devicetree/bindings/dma/jz4780-dma.txt b/Documentation/devicetree/bindings/dma/jz4780-dma.txt
index ec89782d9498..3459e77be294 100644
--- a/Documentation/devicetree/bindings/dma/jz4780-dma.txt
+++ b/Documentation/devicetree/bindings/dma/jz4780-dma.txt
@@ -1,4 +1,4 @@
-* Ingenic JZ4780 DMA Controller
+* Ingenic XBurst DMA Controller
 
 Required properties:
 
@@ -8,10 +8,12 @@ Required properties:
   * ingenic,jz4770-dma
   * ingenic,jz4780-dma
   * ingenic,x1000-dma
+  * ingenic,x1830-dma
 - reg: Should contain the DMA channel registers location and length, followed
   by the DMA controller registers location and length.
 - interrupts: Should contain the interrupt specifier of the DMA controller.
-- clocks: Should contain a clock specifier for the JZ4780/X1000 PDMA clock.
+- clocks: Should contain a clock specifier for the JZ4780/X1000/X1830 PDMA
+  clock.
 - #dma-cells: Must be <2>. Number of integer cells in the dmas property of
   DMA clients (see below).
 
diff --git a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt
index 5551e929fd99..b7f81c63be8b 100644
--- a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt
+++ b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt
@@ -30,6 +30,7 @@ Required Properties:
 		- "renesas,dmac-r8a7794" (R-Car E2)
 		- "renesas,dmac-r8a7795" (R-Car H3)
 		- "renesas,dmac-r8a7796" (R-Car M3-W)
+		- "renesas,dmac-r8a77961" (R-Car M3-W+)
 		- "renesas,dmac-r8a77965" (R-Car M3-N)
 		- "renesas,dmac-r8a77970" (R-Car V3M)
 		- "renesas,dmac-r8a77980" (R-Car V3H)
diff --git a/Documentation/devicetree/bindings/dma/ti/k3-udma.yaml b/Documentation/devicetree/bindings/dma/ti/k3-udma.yaml
new file mode 100644
index 000000000000..8b5c346f23f6
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/ti/k3-udma.yaml
@@ -0,0 +1,184 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/dma/ti/k3-udma.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments K3 NAVSS Unified DMA Device Tree Bindings
+
+maintainers:
+  - Peter Ujfalusi <peter.ujfalusi@ti.com>
+
+description: |
+  The UDMA-P is intended to perform similar (but significantly upgraded)
+  functions as the packet-oriented DMA used on previous SoC devices. The UDMA-P
+  module supports the transmission and reception of various packet types.
+  The UDMA-P architecture facilitates the segmentation and reassembly of SoC DMA
+  data structure compliant packets to/from smaller data blocks that are natively
+  compatible with the specific requirements of each connected peripheral.
+  Multiple Tx and Rx channels are provided within the DMA which allow multiple
+  segmentation or reassembly operations to be ongoing. The DMA controller
+  maintains state information for each of the channels which allows packet
+  segmentation and reassembly operations to be time division multiplexed between
+  channels in order to share the underlying DMA hardware. An external DMA
+  scheduler is used to control the ordering and rate at which this multiplexing
+  occurs for Transmit operations. The ordering and rate of Receive operations
+  is indirectly controlled by the order in which blocks are pushed into the DMA
+  on the Rx PSI-L interface.
+
+  The UDMA-P also supports acting as both a UTC and UDMA-C for its internal
+  channels. Channels in the UDMA-P can be configured to be either Packet-Based
+  or Third-Party channels on a channel by channel basis.
+
+  All transfers within NAVSS is done between PSI-L source and destination
+  threads.
+  The peripherals serviced by UDMA can be PSI-L native (sa2ul, cpsw, etc) or
+  legacy, non PSI-L native peripherals. In the later case a special, small PDMA
+  is tasked to act as a bridge between the PSI-L fabric and the legacy
+  peripheral.
+
+  PDMAs can be configured via UDMAP peer registers to match with the
+  configuration of the legacy peripheral.
+
+allOf:
+  - $ref: "../dma-controller.yaml#"
+
+properties:
+  "#dma-cells":
+    const: 1
+    description: |
+      The cell is the PSI-L  thread ID of the remote (to UDMAP) end.
+      Valid ranges for thread ID depends on the data movement direction:
+      for source thread IDs (rx): 0 - 0x7fff
+      for destination thread IDs (tx): 0x8000 - 0xffff
+
+      Please refer to the device documentation for the PSI-L thread map and also
+      the PSI-L peripheral chapter for the correct thread ID.
+
+  compatible:
+    enum:
+      - ti,am654-navss-main-udmap
+      - ti,am654-navss-mcu-udmap
+      - ti,j721e-navss-main-udmap
+      - ti,j721e-navss-mcu-udmap
+
+  reg:
+    maxItems: 3
+
+  reg-names:
+   items:
+     - const: gcfg
+     - const: rchanrt
+     - const: tchanrt
+
+  msi-parent: true
+
+  ti,sci:
+    description: phandle to TI-SCI compatible System controller node
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/phandle
+
+  ti,sci-dev-id:
+    description: TI-SCI device id of UDMAP
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+
+  ti,ringacc:
+    description: phandle to the ring accelerator node
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/phandle
+
+  ti,sci-rm-range-tchan:
+    description: |
+      Array of UDMA tchan resource subtypes for resource allocation for this
+      host
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 1
+    # Should be enough
+    maxItems: 255
+
+  ti,sci-rm-range-rchan:
+    description: |
+      Array of UDMA rchan resource subtypes for resource allocation for this
+      host
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 1
+    # Should be enough
+    maxItems: 255
+
+  ti,sci-rm-range-rflow:
+    description: |
+      Array of UDMA rflow resource subtypes for resource allocation for this
+      host
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 1
+    # Should be enough
+    maxItems: 255
+
+required:
+  - compatible
+  - "#dma-cells"
+  - reg
+  - reg-names
+  - msi-parent
+  - ti,sci
+  - ti,sci-dev-id
+  - ti,ringacc
+  - ti,sci-rm-range-tchan
+  - ti,sci-rm-range-rchan
+  - ti,sci-rm-range-rflow
+
+examples:
+  - |+
+    cbass_main {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        cbass_main_navss: navss@30800000 {
+            compatible = "simple-mfd";
+            #address-cells = <2>;
+            #size-cells = <2>;
+            dma-coherent;
+            dma-ranges;
+            ranges;
+
+            ti,sci-dev-id = <118>;
+
+            main_udmap: dma-controller@31150000 {
+                compatible = "ti,am654-navss-main-udmap";
+                reg = <0x0 0x31150000 0x0 0x100>,
+                      <0x0 0x34000000 0x0 0x100000>,
+                      <0x0 0x35000000 0x0 0x100000>;
+                reg-names = "gcfg", "rchanrt", "tchanrt";
+                #dma-cells = <1>;
+
+                ti,ringacc = <&ringacc>;
+
+                msi-parent = <&inta_main_udmass>;
+
+                ti,sci = <&dmsc>;
+                ti,sci-dev-id = <188>;
+
+                ti,sci-rm-range-tchan = <0x1>, /* TX_HCHAN */
+                                        <0x2>; /* TX_CHAN */
+                ti,sci-rm-range-rchan = <0x4>, /* RX_HCHAN */
+                                        <0x5>; /* RX_CHAN */
+                ti,sci-rm-range-rflow = <0x6>; /* GP RFLOW */
+            };
+        };
+
+        mcasp0: mcasp@02B00000 {
+            dmas = <&main_udmap 0xc400>, <&main_udmap 0x4400>;
+            dma-names = "tx", "rx";
+        };
+
+        crypto: crypto@4E00000 {
+            compatible = "ti,sa2ul-crypto";
+
+            dmas = <&main_udmap 0xc000>, <&main_udmap 0x4000>, <&main_udmap 0x4001>;
+            dma-names = "tx", "rx1", "rx2";
+        };
+    };
diff --git a/Documentation/devicetree/bindings/soc/ti/k3-ringacc.txt b/Documentation/devicetree/bindings/soc/ti/k3-ringacc.txt
new file mode 100644
index 000000000000..59758ccce809
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/ti/k3-ringacc.txt
@@ -0,0 +1,59 @@
+* Texas Instruments K3 NavigatorSS Ring Accelerator
+
+The Ring Accelerator (RA) is a machine which converts read/write accesses
+from/to a constant address into corresponding read/write accesses from/to a
+circular data structure in memory. The RA eliminates the need for each DMA
+controller which needs to access ring elements from having to know the current
+state of the ring (base address, current offset). The DMA controller
+performs a read or write access to a specific address range (which maps to the
+source interface on the RA) and the RA replaces the address for the transaction
+with a new address which corresponds to the head or tail element of the ring
+(head for reads, tail for writes).
+
+The Ring Accelerator is a hardware module that is responsible for accelerating
+management of the packet queues. The K3 SoCs can have more than one RA instances
+
+Required properties:
+- compatible	: Must be "ti,am654-navss-ringacc";
+- reg		: Should contain register location and length of the following
+		  named register regions.
+- reg-names	: should be
+		  "rt" - The RA Ring Real-time Control/Status Registers
+		  "fifos" - The RA Queues Registers
+		  "proxy_gcfg" - The RA Proxy Global Config Registers
+		  "proxy_target" - The RA Proxy Datapath Registers
+- ti,num-rings	: Number of rings supported by RA
+- ti,sci-rm-range-gp-rings : TI-SCI RM subtype for GP ring range
+- ti,sci	: phandle on TI-SCI compatible System controller node
+- ti,sci-dev-id	: TI-SCI device id of the ring accelerator
+- msi-parent	: phandle for "ti,sci-inta" interrupt controller
+
+Optional properties:
+ -- ti,dma-ring-reset-quirk : enable ringacc / udma ring state interoperability
+		  issue software w/a
+
+Example:
+
+ringacc: ringacc@3c000000 {
+	compatible = "ti,am654-navss-ringacc";
+	reg =	<0x0 0x3c000000 0x0 0x400000>,
+		<0x0 0x38000000 0x0 0x400000>,
+		<0x0 0x31120000 0x0 0x100>,
+		<0x0 0x33000000 0x0 0x40000>;
+	reg-names = "rt", "fifos",
+		    "proxy_gcfg", "proxy_target";
+	ti,num-rings = <818>;
+	ti,sci-rm-range-gp-rings = <0x2>; /* GP ring range */
+	ti,dma-ring-reset-quirk;
+	ti,sci = <&dmsc>;
+	ti,sci-dev-id = <187>;
+	msi-parent = <&inta_main_udmass>;
+};
+
+client:
+
+dma_ipx: dma_ipx@<addr> {
+	...
+	ti,ringacc = <&ringacc>;
+	...
+}