Merge branch 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux

Pull i2c updates from Wolfram Sang:
 "Mostly usual driver updates and improvements.  The changelog should
  give an idea.  Standing out is the i2c-qup driver with lots of new
  capabilities and we also have now an i2c-demuxer.

  I'd especially like to welcome Peter Rosin as the i2c-mux maintainer.
  He has an interesting series for muxes in the queue and agreed to look
  after this part of the subsystem.  Thank you, Peter, and welcome
  again!

  The octeon changes were applied pretty recently before the merge
  window.  I am aware.  They are the first (and relatively simple)
  patches of a larger overhaul to this driver.  In case something goes
  wrong with them, they are easy to fix (or revert).  The advantage I
  see is that they are out of the way, and I can concentrate on the next
  block of patches.  I really would like to apply the overhaul in
  smaller batches to avoid regressions.  And waiting a cycle for the
  introductory patches seemed too much of a delay for me"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (39 commits)
  i2c: octeon: Support I2C_M_RECV_LEN
  i2c: octeon: Cleanup resource allocation code
  i2c: octeon: Cleanup i2c-octeon driver
  MAINTAINERS: add Peter Rosin as i2c mux maintainer
  dt-bindings: i2c: Spelling s/propoerty/property/
  i2c: immediately mark ourselves as registered
  i2c: i801: sort IDs alphabetically
  MAINTAINERS: Mika and me are designated reviewers for I2C DESIGNWARE
  i2c: octeon: Cleanup kerneldoc comments
  i2c: do not use internal data from driver core
  i2c: cadence: Fix the kernel-doc warnings
  i2c: imx: remove extra spaces.
  i2c: rcar: don't open code of_device_get_match_data()
  i2c: qup: Fix fifo handling after adding V2 support
  i2c: xiic: Implement power management
  i2c: piix4: Pre-shift the port number
  i2c: piix4: Always use the same type for port
  i2c: piix4: Support alternative port selection register
  i2c: tegra: don't open code of_device_get_match_data()
  i2c: riic, sh_mobile, rcar: Use ARCH_RENESAS
  ...

5 files changed, 141 insertions, 3 deletions

diff --git a/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt b/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt
new file mode 100644
index 000000000000..6078aefe7ed4
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt
@@ -0,0 +1,135 @@
+Pinctrl-based I2C Bus DeMux
+
+This binding describes an I2C bus demultiplexer that uses pin multiplexing to
+route the I2C signals, and represents the pin multiplexing configuration using
+the pinctrl device tree bindings. This may be used to select one I2C IP core at
+runtime which may have a better feature set for a given task than another I2C
+IP core on the SoC. The most simple example is to fall back to GPIO bitbanging
+if your current runtime configuration hits an errata of the internal IP core.
+
+    +-------------------------------+
+    | SoC                           |
+    |                               |   +-----+  +-----+
+    |   +------------+              |   | dev |  | dev |
+    |   |I2C IP Core1|--\           |   +-----+  +-----+
+    |   +------------+   \-------+  |      |        |
+    |                    |Pinctrl|--|------+--------+
+    |   +------------+   +-------+  |
+    |   |I2C IP Core2|--/           |
+    |   +------------+              |
+    |                               |
+    +-------------------------------+
+
+Required properties:
+- compatible: "i2c-demux-pinctrl"
+- i2c-parent: List of phandles of I2C masters available for selection. The first
+	      one will be used as default.
+- i2c-bus-name: The name of this bus. Also needed as pinctrl-name for the I2C
+		parents.
+
+Furthermore, I2C mux properties and child nodes. See mux.txt in this directory.
+
+Example:
+
+Here is a snipplet for a bus to be demuxed. It contains various i2c clients for
+HDMI, so the bus is named "i2c-hdmi":
+
+	i2chdmi: i2c@8 {
+
+		compatible = "i2c-demux-pinctrl";
+		i2c-parent = <&gpioi2c>, <&iic2>, <&i2c2>;
+		i2c-bus-name = "i2c-hdmi";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ak4643: sound-codec@12 {
+			compatible = "asahi-kasei,ak4643";
+
+			#sound-dai-cells = <0>;
+			reg = <0x12>;
+		};
+
+		composite-in@20 {
+			compatible = "adi,adv7180";
+			reg = <0x20>;
+			remote = <&vin1>;
+
+			port {
+				adv7180: endpoint {
+					bus-width = <8>;
+					remote-endpoint = <&vin1ep0>;
+				};
+			};
+		};
+
+		hdmi@39 {
+			compatible = "adi,adv7511w";
+			reg = <0x39>;
+			interrupt-parent = <&gpio1>;
+			interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+
+			adi,input-depth = <8>;
+			adi,input-colorspace = "rgb";
+			adi,input-clock = "1x";
+			adi,input-style = <1>;
+			adi,input-justification = "evenly";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					adv7511_in: endpoint {
+						remote-endpoint = <&du_out_lvds0>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					adv7511_out: endpoint {
+						remote-endpoint = <&hdmi_con>;
+					};
+				};
+			};
+		};
+	};
+
+And for clarification, here are the snipplets for the i2c-parents:
+
+	gpioi2c: i2c@9 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "i2c-gpio";
+		status = "disabled";
+		gpios = <&gpio5 6 GPIO_ACTIVE_HIGH /* sda */
+			 &gpio5 5 GPIO_ACTIVE_HIGH /* scl */
+			>;
+		i2c-gpio,delay-us = <5>;
+	};
+
+...
+
+&i2c2	{
+	pinctrl-0 = <&i2c2_pins>;
+	pinctrl-names = "i2c-hdmi";
+
+	clock-frequency = <100000>;
+};
+
+...
+
+&iic2	{
+	pinctrl-0 = <&iic2_pins>;
+	pinctrl-names = "i2c-hdmi";
+
+	clock-frequency = <100000>;
+};
+
+Please note:
+
+- pinctrl properties for the parent I2C controllers need a pinctrl state
+  with the same name as i2c-bus-name, not "default"!
+
+- the i2c masters must have their status "disabled". This driver will
+  enable them at runtime when needed.
diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx.txt b/Documentation/devicetree/bindings/i2c/i2c-imx.txt
index eab5836ba7f9..b967544590e8 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-imx.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-imx.txt
@@ -11,7 +11,7 @@ Required properties:
 
 Optional properties:
 - clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz.
-  The absence of the propoerty indicates the default frequency 100 kHz.
+  The absence of the property indicates the default frequency 100 kHz.
 - dmas: A list of two dma specifiers, one for each entry in dma-names.
 - dma-names: should contain "tx" and "rx".
 - scl-gpios: specify the gpio related to SCL pin
diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt
index 95e97223a71c..cf8bfc956cdc 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt
@@ -17,7 +17,7 @@ Required properties:
 
 Optional properties:
 - clock-frequency: desired I2C bus clock frequency in Hz. The absence of this
-  propoerty indicates the default frequency 100 kHz.
+  property indicates the default frequency 100 kHz.
 - clocks: clock specifier.
 
 - i2c-scl-falling-time-ns: see i2c.txt
diff --git a/Documentation/devicetree/bindings/i2c/i2c-sirf.txt b/Documentation/devicetree/bindings/i2c/i2c-sirf.txt
index 7baf9e133fa8..2701eefb00f7 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-sirf.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-sirf.txt
@@ -8,7 +8,7 @@ Required properties :
 
 Optional properties:
 - clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz.
-  The absence of the propoerty indicates the default frequency 100 kHz.
+  The absence of the property indicates the default frequency 100 kHz.
 
 Examples :
 
diff --git a/Documentation/devicetree/bindings/i2c/i2c-xiic.txt b/Documentation/devicetree/bindings/i2c/i2c-xiic.txt
index ceabbe91ae44..caf42e989462 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-xiic.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-xiic.txt
@@ -6,14 +6,17 @@ Required properties:
 - interrupts : IIC controller unterrupt
 - #address-cells = <1>
 - #size-cells = <0>
+- clocks: Input clock specifier. Refer to common clock bindings.
 
 Optional properties:
 - Child nodes conforming to i2c bus binding
+- clock-names: Input clock name, should be 'pclk'.
 
 Example:
 
 	axi_iic_0: i2c@40800000 {
 		compatible = "xlnx,xps-iic-2.00.a";
+		clocks = <&clkc 15>;
 		interrupts = < 1 2 >;
 		reg = < 0x40800000 0x10000 >;