Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

Conflicts were simple overlapping changes in microchip
driver.

Signed-off-by: David S. Miller <davem@davemloft.net>

28 files changed, 549 insertions, 48 deletions

diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt
index 9b8f578d5e19..34a69ba67f13 100644
--- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt
@@ -6,6 +6,7 @@ The MediaTek AUDSYS controller provides various clocks to the system.
 Required Properties:
 
 - compatible: Should be one of:
+	- "mediatek,mt2701-audsys", "syscon"
 	- "mediatek,mt7622-audsys", "syscon"
 - #clock-cells: Must be 1
 
@@ -13,10 +14,19 @@ The AUDSYS controller uses the common clk binding from
 Documentation/devicetree/bindings/clock/clock-bindings.txt
 The available clocks are defined in dt-bindings/clock/mt*-clk.h.
 
+Required sub-nodes:
+-------
+For common binding part and usage, refer to
+../sonud/mt2701-afe-pcm.txt.
+
 Example:
 
-audsys: audsys@11220000 {
-	compatible = "mediatek,mt7622-audsys", "syscon";
-	reg = <0 0x11220000 0 0x1000>;
-	#clock-cells = <1>;
-};
+	audsys: clock-controller@11220000 {
+		compatible = "mediatek,mt7622-audsys", "syscon";
+		reg = <0 0x11220000 0 0x2000>;
+		#clock-cells = <1>;
+
+		afe: audio-controller {
+			...
+		};
+	};
diff --git a/Documentation/devicetree/bindings/clock/imx6sll-clock.txt b/Documentation/devicetree/bindings/clock/imx6sll-clock.txt
new file mode 100644
index 000000000000..fee849d5fdd1
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/imx6sll-clock.txt
@@ -0,0 +1,36 @@
+* Clock bindings for Freescale i.MX6 SLL
+
+Required properties:
+- compatible: Should be "fsl,imx6sll-ccm"
+- reg: Address and length of the register set
+- #clock-cells: Should be <1>
+- clocks: list of clock specifiers, must contain an entry for each required
+  entry in clock-names
+- clock-names: should include entries "ckil", "osc", "ipp_di0" and "ipp_di1"
+
+The clock consumer should specify the desired clock by having the clock
+ID in its "clocks" phandle cell.  See include/dt-bindings/clock/imx6sll-clock.h
+for the full list of i.MX6 SLL clock IDs.
+
+Examples:
+
+#include <dt-bindings/clock/imx6sll-clock.h>
+
+clks: clock-controller@20c4000 {
+		compatible = "fsl,imx6sll-ccm";
+		reg = <0x020c4000 0x4000>;
+		interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+		#clock-cells = <1>;
+		clocks = <&ckil>, <&osc>, <&ipp_di0>, <&ipp_di1>;
+		clock-names = "ckil", "osc", "ipp_di0", "ipp_di1";
+};
+
+uart1: serial@2020000 {
+		compatible = "fsl,imx6sl-uart", "fsl,imx6q-uart", "fsl,imx21-uart";
+		reg = <0x02020000 0x4000>;
+		interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clks IMX6SLL_CLK_UART1_IPG>,
+			 <&clks IMX6SLL_CLK_UART1_SERIAL>;
+		clock-names = "ipg", "per";
+};
diff --git a/Documentation/devicetree/bindings/clock/intc_stratix10.txt b/Documentation/devicetree/bindings/clock/intc_stratix10.txt
new file mode 100644
index 000000000000..9f4ec5cb5c6b
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/intc_stratix10.txt
@@ -0,0 +1,20 @@
+Device Tree Clock bindings for Intel's SoCFPGA Stratix10 platform
+
+This binding uses the common clock binding[1].
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+- compatible : shall be
+	"intel,stratix10-clkmgr"
+
+- reg : shall be the control register offset from CLOCK_MANAGER's base for the clock.
+
+- #clock-cells : from common clock binding, shall be set to 1.
+
+Example:
+	clkmgr: clock-controller@ffd10000 {
+		compatible = "intel,stratix10-clkmgr";
+		reg = <0xffd10000 0x1000>;
+		#clock-cells = <1>;
+	};
diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt
index f1890d0777a6..773a5226342f 100644
--- a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt
+++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt
@@ -22,7 +22,9 @@ Required Properties:
       - "renesas,r8a7794-cpg-mssr" for the r8a7794 SoC (R-Car E2)
       - "renesas,r8a7795-cpg-mssr" for the r8a7795 SoC (R-Car H3)
       - "renesas,r8a7796-cpg-mssr" for the r8a7796 SoC (R-Car M3-W)
+      - "renesas,r8a77965-cpg-mssr" for the r8a77965 SoC (R-Car M3-N)
       - "renesas,r8a77970-cpg-mssr" for the r8a77970 SoC (R-Car V3M)
+      - "renesas,r8a77980-cpg-mssr" for the r8a77980 SoC (R-Car V3H)
       - "renesas,r8a77995-cpg-mssr" for the r8a77995 SoC (R-Car D3)
 
   - reg: Base address and length of the memory resource used by the CPG/MSSR
@@ -32,8 +34,8 @@ Required Properties:
     clock-names
   - clock-names: List of external parent clock names. Valid names are:
       - "extal" (r8a7743, r8a7745, r8a7790, r8a7791, r8a7792, r8a7793, r8a7794,
-		 r8a7795, r8a7796, r8a77970, r8a77995)
-      - "extalr" (r8a7795, r8a7796, r8a77970)
+		 r8a7795, r8a7796, r8a77965, r8a77970, r8a77980, r8a77995)
+      - "extalr" (r8a7795, r8a7796, r8a77965, r8a77970, r8a77980)
       - "usb_extal" (r8a7743, r8a7745, r8a7790, r8a7791, r8a7793, r8a7794)
 
   - #clock-cells: Must be 2
diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt
index e71c675ba5da..904ae682ea90 100644
--- a/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt
+++ b/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt
@@ -32,6 +32,7 @@ clock-output-names:
  - "clkin_i2s" - external I2S clock - optional,
  - "gmac_clkin" - external GMAC clock - optional
  - "phy_50m_out" - output clock of the pll in the mac phy
+ - "hdmi_phy" - output clock of the hdmi phy pll - optional
 
 Example: Clock controller node:
 
diff --git a/Documentation/devicetree/bindings/clock/silabs,si544.txt b/Documentation/devicetree/bindings/clock/silabs,si544.txt
new file mode 100644
index 000000000000..b86535b80920
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/silabs,si544.txt
@@ -0,0 +1,25 @@
+Binding for Silicon Labs 544 programmable I2C clock generator.
+
+Reference
+This binding uses the common clock binding[1]. Details about the device can be
+found in the datasheet[2].
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+[2] Si544 datasheet
+    https://www.silabs.com/documents/public/data-sheets/si544-datasheet.pdf
+
+Required properties:
+ - compatible: One of "silabs,si514a", "silabs,si514b" "silabs,si514c" according
+               to the speed grade of the chip.
+ - reg: I2C device address.
+ - #clock-cells: From common clock bindings: Shall be 0.
+
+Optional properties:
+ - clock-output-names: From common clock bindings. Recommended to be "si544".
+
+Example:
+	si544: clock-controller@55 {
+		reg = <0x55>;
+		#clock-cells = <0>;
+		compatible = "silabs,si544b";
+	};
diff --git a/Documentation/devicetree/bindings/clock/st,stm32mp1-rcc.txt b/Documentation/devicetree/bindings/clock/st,stm32mp1-rcc.txt
new file mode 100644
index 000000000000..fb9495ea582c
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/st,stm32mp1-rcc.txt
@@ -0,0 +1,60 @@
+STMicroelectronics STM32 Peripheral Reset Clock Controller
+==========================================================
+
+The RCC IP is both a reset and a clock controller.
+
+RCC makes also power management (resume/supend and wakeup interrupt).
+
+Please also refer to reset.txt for common reset controller binding usage.
+
+Please also refer to clock-bindings.txt for common clock controller
+binding usage.
+
+
+Required properties:
+- compatible: "st,stm32mp1-rcc", "syscon"
+- reg: should be register base and length as documented in the datasheet
+- #clock-cells: 1, device nodes should specify the clock in their
+  "clocks" property, containing a phandle to the clock device node,
+  an index specifying the clock to use.
+- #reset-cells: Shall be 1
+- interrupts: Should contain a general interrupt line and a interrupt line
+  to the wake-up of processor (CSTOP).
+
+Example:
+	rcc: rcc@50000000 {
+		compatible = "st,stm32mp1-rcc", "syscon";
+		reg = <0x50000000 0x1000>;
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+		interrupts = <GIC_SPI 5 IRQ_TYPE_NONE>,
+			     <GIC_SPI 145 IRQ_TYPE_NONE>;
+	};
+
+Specifying clocks
+=================
+
+All available clocks are defined as preprocessor macros in
+dt-bindings/clock/stm32mp1-clks.h header and can be used in device
+tree sources.
+
+Specifying softreset control of devices
+=======================================
+
+Device nodes should specify the reset channel required in their "resets"
+property, containing a phandle to the reset device node and an index specifying
+which channel to use.
+The index is the bit number within the RCC registers bank, starting from RCC
+base address.
+It is calculated as: index = register_offset / 4 * 32 + bit_offset.
+Where bit_offset is the bit offset within the register.
+
+For example on STM32MP1, for LTDC reset:
+ ltdc = APB4_RSTSETR_offset / 4 * 32 + LTDC_bit_offset
+      = 0x180 / 4 * 32 + 0 = 3072
+
+The list of valid indices for STM32MP1 is available in:
+include/dt-bindings/reset-controller/stm32mp1-resets.h
+
+This file implements defines like:
+#define LTDC_R	3072
diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
index 4ca21c3a6fc9..460ef27b1008 100644
--- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
@@ -20,6 +20,7 @@ Required properties :
 		- "allwinner,sun50i-a64-ccu"
 		- "allwinner,sun50i-a64-r-ccu"
 		- "allwinner,sun50i-h5-ccu"
+		- "allwinner,sun50i-h6-ccu"
 		- "nextthing,gr8-ccu"
 
 - reg: Must contain the registers base address and length
@@ -31,6 +32,9 @@ Required properties :
 - #clock-cells : must contain 1
 - #reset-cells : must contain 1
 
+For the main CCU on H6, one more clock is needed:
+- "iosc": the SoC's internal frequency oscillator
+
 For the PRCM CCUs on A83T/H3/A64, two more clocks are needed:
 - "pll-periph": the SoC's peripheral PLL from the main CCU
 - "iosc": the SoC's internal frequency oscillator
diff --git a/Documentation/devicetree/bindings/clock/ti/davinci/da8xx-cfgchip.txt b/Documentation/devicetree/bindings/clock/ti/davinci/da8xx-cfgchip.txt
new file mode 100644
index 000000000000..1e03dce99a8f
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/ti/davinci/da8xx-cfgchip.txt
@@ -0,0 +1,93 @@
+Binding for TI DA8XX/OMAP-L13X/AM17XX/AM18XX CFGCHIP clocks
+
+TI DA8XX/OMAP-L13X/AM17XX/AM18XX SoCs contain a general purpose set of
+registers call CFGCHIPn. Some of these registers function as clock
+gates. This document describes the bindings for those clocks.
+
+All of the clock nodes described below must be child nodes of a CFGCHIP node
+(compatible = "ti,da830-cfgchip").
+
+USB PHY clocks
+--------------
+Required properties:
+- compatible: shall be "ti,da830-usb-phy-clocks".
+- #clock-cells: from common clock binding; shall be set to 1.
+- clocks: phandles to the parent clocks corresponding to clock-names
+- clock-names: shall be "fck", "usb_refclkin", "auxclk"
+
+This node provides two clocks. The clock at index 0 is the USB 2.0 PHY 48MHz
+clock and the clock at index 1 is the USB 1.1 PHY 48MHz clock.
+
+eHRPWM Time Base Clock (TBCLK)
+------------------------------
+Required properties:
+- compatible: shall be "ti,da830-tbclksync".
+- #clock-cells: from common clock binding; shall be set to 0.
+- clocks: phandle to the parent clock
+- clock-names: shall be "fck"
+
+PLL DIV4.5 divider
+------------------
+Required properties:
+- compatible: shall be "ti,da830-div4p5ena".
+- #clock-cells: from common clock binding; shall be set to 0.
+- clocks: phandle to the parent clock
+- clock-names: shall be "pll0_pllout"
+
+EMIFA clock source (ASYNC1)
+---------------------------
+Required properties:
+- compatible: shall be "ti,da850-async1-clksrc".
+- #clock-cells: from common clock binding; shall be set to 0.
+- clocks: phandles to the parent clocks corresponding to clock-names
+- clock-names: shall be "pll0_sysclk3", "div4.5"
+
+ASYNC3 clock source
+-------------------
+Required properties:
+- compatible: shall be "ti,da850-async3-clksrc".
+- #clock-cells: from common clock binding; shall be set to 0.
+- clocks: phandles to the parent clocks corresponding to clock-names
+- clock-names: shall be "pll0_sysclk2", "pll1_sysclk2"
+
+Examples:
+
+	cfgchip: syscon@1417c {
+		compatible = "ti,da830-cfgchip", "syscon", "simple-mfd";
+		reg = <0x1417c 0x14>;
+
+		usb_phy_clk: usb-phy-clocks {
+			compatible = "ti,da830-usb-phy-clocks";
+			#clock-cells = <1>;
+			clocks = <&psc1 1>, <&usb_refclkin>, <&pll0_auxclk>;
+			clock-names = "fck", "usb_refclkin", "auxclk";
+		};
+		ehrpwm_tbclk: ehrpwm_tbclk {
+			compatible = "ti,da830-tbclksync";
+			#clock-cells = <0>;
+			clocks = <&psc1 17>;
+			clock-names = "fck";
+		};
+		div4p5_clk: div4.5 {
+			compatible = "ti,da830-div4p5ena";
+			#clock-cells = <0>;
+			clocks = <&pll0_pllout>;
+			clock-names = "pll0_pllout";
+		};
+		async1_clk: async1 {
+			compatible = "ti,da850-async1-clksrc";
+			#clock-cells = <0>;
+			clocks = <&pll0_sysclk 3>, <&div4p5_clk>;
+			clock-names = "pll0_sysclk3", "div4.5";
+		};
+		async3_clk: async3 {
+			compatible = "ti,da850-async3-clksrc";
+			#clock-cells = <0>;
+			clocks = <&pll0_sysclk 2>, <&pll1_sysclk 2>;
+			clock-names = "pll0_sysclk2", "pll1_sysclk2";
+		};
+	};
+
+Also see:
+- Documentation/devicetree/bindings/clock/clock-bindings.txt
+
diff --git a/Documentation/devicetree/bindings/clock/ti/davinci/pll.txt b/Documentation/devicetree/bindings/clock/ti/davinci/pll.txt
new file mode 100644
index 000000000000..36998e184821
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/ti/davinci/pll.txt
@@ -0,0 +1,96 @@
+Binding for TI DaVinci PLL Controllers
+
+The PLL provides clocks to most of the components on the SoC. In addition
+to the PLL itself, this controller also contains bypasses, gates, dividers,
+an multiplexers for various clock signals.
+
+Required properties:
+- compatible: shall be one of:
+	- "ti,da850-pll0" for PLL0 on DA850/OMAP-L138/AM18XX
+	- "ti,da850-pll1" for PLL1 on DA850/OMAP-L138/AM18XX
+- reg: physical base address and size of the controller's register area.
+- clocks: phandles corresponding to the clock names
+- clock-names: names of the clock sources - depends on compatible string
+	- for "ti,da850-pll0", shall be "clksrc", "extclksrc"
+	- for "ti,da850-pll1", shall be "clksrc"
+
+Optional properties:
+- ti,clkmode-square-wave: Indicates that the the board is supplying a square
+	wave input on the OSCIN pin instead of using a crystal oscillator.
+	This property is only valid when compatible = "ti,da850-pll0".
+
+
+Optional child nodes:
+
+pllout
+	Describes the main PLL clock output (before POSTDIV). The node name must
+	be "pllout".
+
+	Required properties:
+	- #clock-cells: shall be 0
+
+sysclk
+	Describes the PLLDIVn divider clocks that provide the SYSCLKn clock
+	domains. The node name must be "sysclk". Consumers of this node should
+	use "n" in "SYSCLKn" as the index parameter for the clock cell.
+
+	Required properties:
+	- #clock-cells: shall be 1
+
+auxclk
+	Describes the AUXCLK output of the PLL. The node name must be "auxclk".
+	This child node is only valid when compatible = "ti,da850-pll0".
+
+	Required properties:
+	- #clock-cells: shall be 0
+
+obsclk
+	Describes the OBSCLK output of the PLL. The node name must be "obsclk".
+
+	Required properties:
+	- #clock-cells: shall be 0
+
+
+Examples:
+
+	pll0: clock-controller@11000 {
+		compatible = "ti,da850-pll0";
+		reg = <0x11000 0x1000>;
+		clocks = <&ref_clk>, <&pll1_sysclk 3>;
+		clock-names = "clksrc", "extclksrc";
+		ti,clkmode-square-wave;
+
+		pll0_pllout: pllout {
+			#clock-cells = <0>;
+		};
+
+		pll0_sysclk: sysclk {
+			#clock-cells = <1>;
+		};
+
+		pll0_auxclk: auxclk {
+			#clock-cells = <0>;
+		};
+
+		pll0_obsclk: obsclk {
+			#clock-cells = <0>;
+		};
+	};
+
+	pll1: clock-controller@21a000 {
+		compatible = "ti,da850-pll1";
+		reg = <0x21a000 0x1000>;
+		clocks = <&ref_clk>;
+		clock-names = "clksrc";
+
+		pll0_sysclk: sysclk {
+			#clock-cells = <1>;
+		};
+
+		pll0_obsclk: obsclk {
+			#clock-cells = <0>;
+		};
+	};
+
+Also see:
+- Documentation/devicetree/bindings/clock/clock-bindings.txt
diff --git a/Documentation/devicetree/bindings/clock/ti/davinci/psc.txt b/Documentation/devicetree/bindings/clock/ti/davinci/psc.txt
new file mode 100644
index 000000000000..dae4ad8e198c
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/ti/davinci/psc.txt
@@ -0,0 +1,71 @@
+Binding for TI DaVinci Power Sleep Controller (PSC)
+
+The PSC provides power management, clock gating and reset functionality. It is
+primarily used for clocking.
+
+Required properties:
+- compatible: shall be one of:
+	- "ti,da850-psc0" for PSC0 on DA850/OMAP-L138/AM18XX
+	- "ti,da850-psc1" for PSC1 on DA850/OMAP-L138/AM18XX
+- reg: physical base address and size of the controller's register area
+- #clock-cells: from common clock binding; shall be set to 1
+- #power-domain-cells: from generic power domain binding; shall be set to 1.
+- clocks: phandles to clocks corresponding to the clock-names property
+- clock-names: list of parent clock names - depends on compatible value
+	- for "ti,da850-psc0", shall be "pll0_sysclk1", "pll0_sysclk2",
+	  "pll0_sysclk4", "pll0_sysclk6", "async1"
+	- for "ti,da850-psc1", shall be "pll0_sysclk2", "pll0_sysclk4", "async3"
+
+Optional properties:
+- #reset-cells: from reset binding; shall be set to 1 - only applicable when
+  at least one local domain provides a local reset.
+
+Consumers:
+
+	Clock, power domain and reset consumers shall use the local power domain
+	module ID (LPSC) as the index corresponding to the clock cell. Refer to
+	the device-specific datasheet to find these numbers. NB: Most local
+	domains	only provide a clock/power domain and not a reset.
+
+Examples:
+
+	psc0: clock-controller@10000 {
+		compatible = "ti,da850-psc0";
+		reg = <0x10000 0x1000>;
+		#clock-cells = <1>;
+		#power-domain-cells = <1>;
+		#reset-cells = <1>;
+		clocks = <&pll0_sysclk 1>, <&pll0_sysclk 2>,
+			 <&pll0_sysclk 4>, <&pll0_sysclk 6>, <&async1_clk>;
+		clock_names = "pll0_sysclk1", "pll0_sysclk2",
+			      "pll0_sysclk4", "pll0_sysclk6", "async1";
+	};
+	psc1: clock-controller@227000 {
+		compatible = "ti,da850-psc1";
+		reg = <0x227000 0x1000>;
+		#clock-cells = <1>;
+		#power-domain-cells = <1>;
+		clocks = <&pll0_sysclk 2>, <&pll0_sysclk 4>, <&async3_clk>;
+		clock_names = "pll0_sysclk2", "pll0_sysclk4", "async3";
+	};
+
+	/* consumer */
+	dsp: dsp@11800000 {
+		compatible = "ti,da850-dsp";
+		reg = <0x11800000 0x40000>,
+		      <0x11e00000 0x8000>,
+		      <0x11f00000 0x8000>,
+		      <0x01c14044 0x4>,
+		      <0x01c14174 0x8>;
+		reg-names = "l2sram", "l1pram", "l1dram", "host1cfg", "chipsig";
+		interrupt-parent = <&intc>;
+		interrupts = <28>;
+		clocks = <&psc0 15>;
+		power-domains = <&psc0 15>;
+		resets = <&psc0 15>;
+	};
+
+Also see:
+- Documentation/devicetree/bindings/clock/clock-bindings.txt
+- Documentation/devicetree/bindings/power/power_domain.txt
+- Documentation/devicetree/bindings/reset/reset.txt
diff --git a/Documentation/devicetree/bindings/clock/ti/divider.txt b/Documentation/devicetree/bindings/clock/ti/divider.txt
index 35a6f5c7e5c2..9b13b32974f9 100644
--- a/Documentation/devicetree/bindings/clock/ti/divider.txt
+++ b/Documentation/devicetree/bindings/clock/ti/divider.txt
@@ -75,6 +75,9 @@ Optional properties:
 - ti,invert-autoidle-bit : autoidle is enabled by setting the bit to 0,
   see [2]
 - ti,set-rate-parent : clk_set_rate is propagated to parent
+- ti,latch-bit : latch the divider value to HW, only needed if the register
+  access requires this. As an example dra76x DPLL_GMAC H14 divider implements
+  such behavior.
 
 Examples:
 dpll_usb_m2_ck: dpll_usb_m2_ck@4a008190 {
diff --git a/Documentation/devicetree/bindings/clock/ti/mux.txt b/Documentation/devicetree/bindings/clock/ti/mux.txt
index 2d0d170f8001..eec8994b9be8 100644
--- a/Documentation/devicetree/bindings/clock/ti/mux.txt
+++ b/Documentation/devicetree/bindings/clock/ti/mux.txt
@@ -48,6 +48,9 @@ Optional properties:
   zero
 - ti,set-rate-parent : clk_set_rate is propagated to parent clock,
   not supported by the composite-mux-clock subtype
+- ti,latch-bit : latch the mux value to HW, only needed if the register
+  access requires this. As an example, dra7x DPLL_GMAC H14 muxing
+  implements such behavior.
 
 Examples:
 
diff --git a/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt b/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt
new file mode 100644
index 000000000000..7d9d3f90641b
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt
@@ -0,0 +1,25 @@
+Ingenic JZ47xx PWM Controller
+=============================
+
+Required properties:
+- compatible: One of:
+  * "ingenic,jz4740-pwm"
+  * "ingenic,jz4770-pwm"
+  * "ingenic,jz4780-pwm"
+- #pwm-cells: Should be 3. See pwm.txt in this directory for a description
+  of the cells format.
+- clocks : phandle to the external clock.
+- clock-names : Should be "ext".
+
+
+Example:
+
+	pwm: pwm@10002000 {
+		compatible = "ingenic,jz4740-pwm";
+		reg = <0x10002000 0x1000>;
+
+		#pwm-cells = <3>;
+
+		clocks = <&ext>;
+		clock-names = "ext";
+	};
diff --git a/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt b/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt
index f8338d11fd2b..bd23302e84be 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt
@@ -7,6 +7,8 @@ See ../mfd/stm32-lptimer.txt for details about the parent node.
 
 Required parameters:
 - compatible:		Must be "st,stm32-pwm-lp".
+- #pwm-cells:		Should be set to 3. This PWM chip uses the default 3 cells
+			bindings defined in pwm.txt.
 
 Optional properties:
 - pinctrl-names: 	Set to "default".
@@ -18,6 +20,7 @@ Example:
 		...
 		pwm {
 			compatible = "st,stm32-pwm-lp";
+			#pwm-cells = <3>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&lppwm1_pins>;
 		};
diff --git a/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt b/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt
index 51ff54c8b8ef..2a1affbff45e 100644
--- a/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt
+++ b/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt
@@ -7,6 +7,8 @@ Required properties:
     - "allwinner,sun5i-a13-pwm"
     - "allwinner,sun7i-a20-pwm"
     - "allwinner,sun8i-h3-pwm"
+    - "allwinner,sun50i-a64-pwm", "allwinner,sun5i-a13-pwm"
+    - "allwinner,sun50i-h5-pwm", "allwinner,sun5i-a13-pwm"
   - reg: physical base address and length of the controller's registers
   - #pwm-cells: should be 3. See pwm.txt in this directory for a description of
     the cells format.
diff --git a/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt b/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt
index 74c118015980..35a3b9761ee5 100644
--- a/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt
+++ b/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt
@@ -2,6 +2,8 @@
 
 Required Properties:
 - compatible: should be "renesas,pwm-rcar" and one of the following.
+ - "renesas,pwm-r8a7743": for RZ/G1M
+ - "renesas,pwm-r8a7745": for RZ/G1E
  - "renesas,pwm-r8a7778": for R-Car M1A
  - "renesas,pwm-r8a7779": for R-Car H1
  - "renesas,pwm-r8a7790": for R-Car H2
@@ -9,6 +11,7 @@ Required Properties:
  - "renesas,pwm-r8a7794": for R-Car E2
  - "renesas,pwm-r8a7795": for R-Car H3
  - "renesas,pwm-r8a7796": for R-Car M3-W
+ - "renesas,pwm-r8a77965": for R-Car M3-N
  - "renesas,pwm-r8a77995": for R-Car D3
 - reg: base address and length of the registers block for the PWM.
 - #pwm-cells: should be 2. See pwm.txt in this directory for a description of
@@ -17,13 +20,15 @@ Required Properties:
 - pinctrl-0: phandle, referring to a default pin configuration node.
 - pinctrl-names: Set to "default".
 
-Example: R8A7790 (R-Car H2) PWM Timer node
+Example: R8A7743 (RZ/G1M) PWM Timer node
 
 	pwm0: pwm@e6e30000 {
-		compatible = "renesas,pwm-r8a7790", "renesas,pwm-rcar";
+		compatible = "renesas,pwm-r8a7743", "renesas,pwm-rcar";
 		reg = <0 0xe6e30000 0 0x8>;
+		clocks = <&cpg CPG_MOD 523>;
+		power-domains = <&sysc R8A7743_PD_ALWAYS_ON>;
+		resets = <&cpg 523>;
 		#pwm-cells = <2>;
-		clocks = <&mstp5_clks R8A7790_CLK_PWM>;
 		pinctrl-0 = <&pwm0_pins>;
 		pinctrl-names = "default";
 	};
diff --git a/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt b/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt
index 1aadc804dae4..d53a16715da6 100644
--- a/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt
@@ -3,10 +3,12 @@
 Required Properties:
 
   - compatible: should be one of the following.
-    - "renesas,tpu-r8a73a4": for R8A77A4 (R-Mobile APE6) compatible PWM controller.
+    - "renesas,tpu-r8a73a4": for R8A73A4 (R-Mobile APE6) compatible PWM controller.
     - "renesas,tpu-r8a7740": for R8A7740 (R-Mobile A1) compatible PWM controller.
+    - "renesas,tpu-r8a7743": for R8A7743 (RZ/G1M) compatible PWM controller.
+    - "renesas,tpu-r8a7745": for R8A7745 (RZ/G1E) compatible PWM controller.
     - "renesas,tpu-r8a7790": for R8A7790 (R-Car H2) compatible PWM controller.
-    - "renesas,tpu": for generic R-Car TPU PWM controller.
+    - "renesas,tpu": for generic R-Car and RZ/G1 TPU PWM controller.
 
   - reg: Base address and length of each memory resource used by the PWM
     controller hardware module.
@@ -18,10 +20,10 @@ Required Properties:
 Please refer to pwm.txt in this directory for details of the common PWM bindings
 used by client devices.
 
-Example: R8A7740 (R-Car A1) TPU controller node
+Example: R8A7740 (R-Mobile A1) TPU controller node
 
 	tpu: pwm@e6600000 {
 		compatible = "renesas,tpu-r8a7740", "renesas,tpu";
-		reg = <0xe6600000 0x100>;
+		reg = <0xe6600000 0x148>;
 		#pwm-cells = <3>;
 	};
diff --git a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt
index 1b596fd38dc4..b957acff57aa 100644
--- a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt
+++ b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt
@@ -49,19 +49,6 @@ on the SoC (only first trip points defined in DT will be configured):
  - samsung,exynos5433-tmu: 8
  - samsung,exynos7-tmu: 8
 
-Following properties are mandatory (depending on SoC):
-- samsung,tmu_gain: Gain value for internal TMU operation.
-- samsung,tmu_reference_voltage: Value of TMU IP block's reference voltage
-- samsung,tmu_noise_cancel_mode: Mode for noise cancellation
-- samsung,tmu_efuse_value: Default level of temperature - it is needed when
-			   in factory fusing produced wrong value
-- samsung,tmu_min_efuse_value: Minimum temperature fused value
-- samsung,tmu_max_efuse_value: Maximum temperature fused value
-- samsung,tmu_first_point_trim: First point trimming value
-- samsung,tmu_second_point_trim: Second point trimming value
-- samsung,tmu_default_temp_offset: Default temperature offset
-- samsung,tmu_cal_type: Callibration type
-
 ** Optional properties:
 
 - vtmu-supply: This entry is optional and provides the regulator node supplying
@@ -78,7 +65,7 @@ Example 1):
 		clocks = <&clock 383>;
 		clock-names = "tmu_apbif";
 		vtmu-supply = <&tmu_regulator_node>;
-		#include "exynos4412-tmu-sensor-conf.dtsi"
+		#thermal-sensor-cells = <0>;
 	};
 
 Example 2):
@@ -89,7 +76,7 @@ Example 2):
 		interrupts = <0 58 0>;
 		clocks = <&clock 21>;
 		clock-names = "tmu_apbif";
-		#include "exynos5440-tmu-sensor-conf.dtsi"
+		#thermal-sensor-cells = <0>;
 	};
 
 Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register")
@@ -99,7 +86,7 @@ Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register")
 		interrupts = <0 184 0>;
 		clocks = <&clock 318>, <&clock 318>;
 		clock-names = "tmu_apbif", "tmu_triminfo_apbif";
-		#include "exynos4412-tmu-sensor-conf.dtsi"
+		#thermal-sensor-cells = <0>;
 	};
 
 	tmu_cpu3: tmu@1006c000 {
@@ -108,7 +95,7 @@ Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register")
 		interrupts = <0 185 0>;
 		clocks = <&clock 318>, <&clock 319>;
 		clock-names = "tmu_apbif", "tmu_triminfo_apbif";
-		#include "exynos4412-tmu-sensor-conf.dtsi"
+		#thermal-sensor-cells = <0>;
 	};
 
 	tmu_gpu: tmu@100a0000 {
@@ -117,7 +104,7 @@ Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register")
 		interrupts = <0 215 0>;
 		clocks = <&clock 319>, <&clock 318>;
 		clock-names = "tmu_apbif", "tmu_triminfo_apbif";
-		#include "exynos4412-tmu-sensor-conf.dtsi"
+		#thermal-sensor-cells = <0>;
 	};
 
 Note: For multi-instance tmu each instance should have an alias correctly
diff --git a/Documentation/devicetree/bindings/thermal/thermal.txt b/Documentation/devicetree/bindings/thermal/thermal.txt
index 1719d47a5e2f..cc553f0952c5 100644
--- a/Documentation/devicetree/bindings/thermal/thermal.txt
+++ b/Documentation/devicetree/bindings/thermal/thermal.txt
@@ -55,8 +55,7 @@ of heat dissipation). For example a fan's cooling states correspond to
 the different fan speeds possible. Cooling states are referred to by
 single unsigned integers, where larger numbers mean greater heat
 dissipation. The precise set of cooling states associated with a device
-(as referred to by the cooling-min-level and cooling-max-level
-properties) should be defined in a particular device's binding.
+should be defined in a particular device's binding.
 For more examples of cooling devices, refer to the example sections below.
 
 Required properties:
@@ -69,15 +68,6 @@ Required properties:
 			See Cooling device maps section below for more details
 			on how consumers refer to cooling devices.
 
-Optional properties:
-- cooling-min-level:	An integer indicating the smallest
-  Type: unsigned	cooling state accepted. Typically 0.
-  Size: one cell
-
-- cooling-max-level:	An integer indicating the largest
-  Type: unsigned	cooling state accepted.
-  Size: one cell
-
 * Trip points
 
 The trip node is a node to describe a point in the temperature domain
@@ -226,8 +216,6 @@ cpus {
 			396000  950000
 			198000  850000
 		>;
-		cooling-min-level = <0>;
-		cooling-max-level = <3>;
 		#cooling-cells = <2>; /* min followed by max */
 	};
 	...
@@ -241,8 +229,6 @@ cpus {
 	 */
 	fan0: fan@48 {
 		...
-		cooling-min-level = <0>;
-		cooling-max-level = <9>;
 		#cooling-cells = <2>; /* min followed by max */
 	};
 };
diff --git a/Documentation/devicetree/bindings/timer/nuvoton,npcm7xx-timer.txt b/Documentation/devicetree/bindings/timer/nuvoton,npcm7xx-timer.txt
new file mode 100644
index 000000000000..ea22dfe485be
--- /dev/null
+++ b/Documentation/devicetree/bindings/timer/nuvoton,npcm7xx-timer.txt
@@ -0,0 +1,21 @@
+Nuvoton NPCM7xx timer
+
+Nuvoton NPCM7xx have three timer modules, each timer module provides five 24-bit
+timer counters.
+
+Required properties:
+- compatible      : "nuvoton,npcm750-timer" for Poleg NPCM750.
+- reg             : Offset and length of the register set for the device.
+- interrupts      : Contain the timer interrupt with flags for
+                    falling edge.
+- clocks          : phandle of timer reference clock (usually a 25 MHz clock).
+
+Example:
+
+timer@f0008000 {
+    compatible = "nuvoton,npcm750-timer";
+    interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+    reg = <0xf0008000 0x50>;
+    clocks = <&clk NPCM7XX_CLK_TIMER>;
+};
+
diff --git a/Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt b/Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt
index b4aa7ddb5b13..f82087b220f4 100644
--- a/Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt
+++ b/Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt
@@ -15,7 +15,7 @@ Required properties:
 - interrupts :	Should be the clock event device interrupt.
 - clocks :	The clocks provided by the SoC to drive the timer, must contain
 		an entry for each entry in clock-names.
-- clock-names : Must include the following entries: "igp" and "per".
+- clock-names : Must include the following entries: "ipg" and "per".
 
 Example:
 tpm5: tpm@40260000 {
diff --git a/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt b/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt
index 107280ef0025..adc6b76fcb3a 100644
--- a/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt
+++ b/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt
@@ -11,6 +11,7 @@ Optional properties:
   detail please see: Documentation/devicetree/bindings/regmap/regmap.txt.
 - fsl,ext-reset-output: If present the watchdog device is configured to
   assert its external reset (WDOG_B) instead of issuing a software reset.
+- timeout-sec : Contains the watchdog timeout in seconds
 
 Examples:
 
@@ -19,4 +20,5 @@ wdt@73f98000 {
 	reg = <0x73f98000 0x4000>;
 	interrupts = <58>;
 	big-endian;
+	timeout-sec = <20>;
 };
diff --git a/Documentation/devicetree/bindings/watchdog/meson-wdt.txt b/Documentation/devicetree/bindings/watchdog/meson-wdt.txt
index 8a6d84cb36c9..7588cc3971bf 100644
--- a/Documentation/devicetree/bindings/watchdog/meson-wdt.txt
+++ b/Documentation/devicetree/bindings/watchdog/meson-wdt.txt
@@ -9,9 +9,13 @@ Required properties:
 	"amlogic,meson8m2-wdt" and "amlogic,meson8b-wdt" on Meson8m2 SoCs
 - reg : Specifies base physical address and size of the registers.
 
+Optional properties:
+- timeout-sec: contains the watchdog timeout in seconds.
+
 Example:
 
 wdt: watchdog@c1109900 {
 	compatible = "amlogic,meson6-wdt";
 	reg = <0xc1109900 0x8>;
+	timeout-sec = <10>;
 };
diff --git a/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt b/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt
index 5b38a30e608c..859dee167b91 100644
--- a/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt
+++ b/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt
@@ -11,9 +11,13 @@ Required properties:
 
 - reg : Specifies base physical address and size of the registers.
 
+Optional properties:
+- timeout-sec: contains the watchdog timeout in seconds.
+
 Example:
 
 wdt: watchdog@10000000 {
 	compatible = "mediatek,mt6589-wdt";
 	reg = <0x10000000 0x18>;
+	timeout-sec = <10>;
 };
diff --git a/Documentation/devicetree/bindings/watchdog/nuvoton,npcm-wdt.txt b/Documentation/devicetree/bindings/watchdog/nuvoton,npcm-wdt.txt
new file mode 100644
index 000000000000..6d593003c933
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/nuvoton,npcm-wdt.txt
@@ -0,0 +1,28 @@
+Nuvoton NPCM Watchdog
+
+Nuvoton NPCM timer module provides five 24-bit timer counters, and a watchdog.
+The watchdog supports a pre-timeout interrupt that fires 10ms before the
+expiry.
+
+Required properties:
+- compatible      : "nuvoton,npcm750-wdt" for NPCM750 (Poleg).
+- reg             : Offset and length of the register set for the device.
+- interrupts      : Contain the timer interrupt with flags for
+                    falling edge.
+
+Required clocking property, have to be one of:
+- clocks          : phandle of timer reference clock.
+- clock-frequency : The frequency in Hz of the clock that drives the NPCM7xx
+                    timer (usually 25000000).
+
+Optional properties:
+- timeout-sec : Contains the watchdog timeout in seconds
+
+Example:
+
+timer@f000801c {
+    compatible = "nuvoton,npcm750-wdt";
+    interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+    reg = <0xf000801c 0x4>;
+    clocks = <&clk NPCM7XX_CLK_TIMER>;
+};
diff --git a/Documentation/devicetree/bindings/watchdog/sirfsoc_wdt.txt b/Documentation/devicetree/bindings/watchdog/sirfsoc_wdt.txt
index 9cbc76c89b2b..0dce5e3100b4 100644
--- a/Documentation/devicetree/bindings/watchdog/sirfsoc_wdt.txt
+++ b/Documentation/devicetree/bindings/watchdog/sirfsoc_wdt.txt
@@ -5,10 +5,14 @@ Required properties:
 - reg: Address range of tick timer/WDT register set
 - interrupts: interrupt number to the cpu
 
+Optional properties:
+- timeout-sec : Contains the watchdog timeout in seconds
+
 Example:
 
 timer@b0020000 {
 	compatible = "sirf,prima2-tick";
 	reg = <0xb0020000 0x1000>;
 	interrupts = <0>;
+	timeout-sec = <30>;
 };
diff --git a/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt b/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt
index 04fc368d828f..ed11ce0ac836 100644
--- a/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt
+++ b/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt
@@ -8,9 +8,13 @@ Required properties:
 	"allwinner,sun50i-a64-wdt","allwinner,sun6i-a31-wdt"
 - reg : Specifies base physical address and size of the registers.
 
+Optional properties:
+- timeout-sec : Contains the watchdog timeout in seconds
+
 Example:
 
 wdt: watchdog@1c20c90 {
 	compatible = "allwinner,sun4i-a10-wdt";
 	reg = <0x01c20c90 0x10>;
+	timeout-sec = <10>;
 };