Merge tag 'hwmon-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:

 - Add driver for Intersil ISL68137 PWM Controller

 - Add driver for Lochnagar 2

 - Add driver for Infineon IR38064 Voltage Regulator

 - Add support for TMP75B to lm75 driver

 - Convert documentation to ReST format

 - Use request_muxed_region for Super-IO accesses in several drivers

 - Add 'samples' attribute to ABI, and start using it

 - Add support for custom sysfs attributes to pmbus drivers (used in
   ISL68137 driver)

 - Introduce HWMON_CHANNEL_INFO macro

 - Automated changes:
      - Use permission specific [SENSOR_][DEVICE_]ATTR variants
      - Fix build warnings due to unused of_device_id structures
      - Use HWMON_CHANNEL_INFO macro

 - Various minor improvements and fixes

* tag 'hwmon-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (125 commits)
  hwmon: (lm75) Add support for TMP75B
  dt-bindings: hwmon: Add tmp75b to lm75.txt
  hwmon: (s3c) Use dev_get_drvdata()
  hwmon: (max6650) Drop call to thermal_cdev_update
  docs: hwmon: remove the extension from .rst files
  docs: hwmon: convert three docs to ReST format
  hwmon: (max6650) add thermal cooling device capability
  hwmon: (ina3221) Add voltage conversion time settings
  hwmon: (ina3221) Do not read-back to cache reg_config
  docs: hwmon: Add an index file and rename docs to *.rst
  docs: hwmon: convert remaining files to ReST format
  docs: hwmon: misc files: convert to ReST format
  docs: hwmon: pmbus files: convert to ReST format
  docs: hwmon: k8temp, w83793: convert to ReST format
  docs: hwmon: da9052, da9055: convert to ReST format
  docs: hwmon: wm831x, wm8350: convert to ReST format
  docs: hwmon: dme1737, vt1211: convert to ReST format
  docs: hwmon: ads1015: convert to ReST format
  docs: hwmon: asc7621: convert to ReST format
  docs: hwmon: ibmpowernv: convert to ReST format
  ...

1 files changed, 92 insertions, 0 deletions

diff --git a/Documentation/hwmon/ltc2945.rst b/Documentation/hwmon/ltc2945.rst
new file mode 100644
index 000000000000..20c884985367
--- /dev/null
+++ b/Documentation/hwmon/ltc2945.rst
@@ -0,0 +1,92 @@
+Kernel driver ltc2945
+=====================
+
+Supported chips:
+
+  * Linear Technology LTC2945
+
+    Prefix: 'ltc2945'
+
+    Addresses scanned: -
+
+    Datasheet:
+
+	http://cds.linear.com/docs/en/datasheet/2945fa.pdf
+
+Author: Guenter Roeck <linux@roeck-us.net>
+
+
+Description
+-----------
+
+The LTC2945  is a rail-to-rail system monitor that measures current, voltage,
+and power consumption.
+
+
+Usage Notes
+-----------
+
+This driver does not probe for LTC2945 devices, since there is no register
+which can be safely used to identify the chip. You will have to instantiate
+the devices explicitly.
+
+Example: the following will load the driver for an LTC2945 at address 0x10
+on I2C bus #1::
+
+	$ modprobe ltc2945
+	$ echo ltc2945 0x10 > /sys/bus/i2c/devices/i2c-1/new_device
+
+
+Sysfs entries
+-------------
+
+Voltage readings provided by this driver are reported as obtained from the ADC
+registers. If a set of voltage divider resistors is installed, calculate the
+real voltage by multiplying the reported value with (R1+R2)/R2, where R1 is the
+value of the divider resistor against the measured voltage and R2 is the value
+of the divider resistor against Ground.
+
+Current reading provided by this driver is reported as obtained from the ADC
+Current Sense register. The reported value assumes that a 1 mOhm sense resistor
+is installed. If a different sense resistor is installed, calculate the real
+current by dividing the reported value by the sense resistor value in mOhm.
+
+======================= ========================================================
+in1_input		VIN voltage (mV). Voltage is measured either at
+			SENSE+ or VDD pin depending on chip configuration.
+in1_min			Undervoltage threshold
+in1_max			Overvoltage threshold
+in1_lowest		Lowest measured voltage
+in1_highest		Highest measured voltage
+in1_reset_history	Write 1 to reset in1 history
+in1_min_alarm		Undervoltage alarm
+in1_max_alarm		Overvoltage alarm
+
+in2_input		ADIN voltage (mV)
+in2_min			Undervoltage threshold
+in2_max			Overvoltage threshold
+in2_lowest		Lowest measured voltage
+in2_highest		Highest measured voltage
+in2_reset_history	Write 1 to reset in2 history
+in2_min_alarm		Undervoltage alarm
+in2_max_alarm		Overvoltage alarm
+
+curr1_input		SENSE current (mA)
+curr1_min		Undercurrent threshold
+curr1_max		Overcurrent threshold
+curr1_lowest		Lowest measured current
+curr1_highest		Highest measured current
+curr1_reset_history	Write 1 to reset curr1 history
+curr1_min_alarm		Undercurrent alarm
+curr1_max_alarm		Overcurrent alarm
+
+power1_input		Power (in uW). Power is calculated based on SENSE+/VDD
+			voltage or ADIN voltage depending on chip configuration.
+power1_min		Low lower threshold
+power1_max		High power threshold
+power1_input_lowest	Historical minimum power use
+power1_input_highest	Historical maximum power use
+power1_reset_history	Write 1 to reset power1 history
+power1_min_alarm	Low power alarm
+power1_max_alarm	High power alarm
+======================= ========================================================