docs: hwmon: Add an index file and rename docs to *.rst

Now that all files were converted to ReST format, rename them
and add an index.

Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

1 files changed, 0 insertions, 88 deletions

diff --git a/Documentation/hwmon/sht3x b/Documentation/hwmon/sht3x
deleted file mode 100644
index 978a7117e4b2..000000000000
--- a/Documentation/hwmon/sht3x
+++ /dev/null
@@ -1,88 +0,0 @@
-Kernel driver sht3x
-===================
-
-Supported chips:
-
-  * Sensirion SHT3x-DIS
-
-    Prefix: 'sht3x'
-
-    Addresses scanned: none
-
-    Datasheet: https://www.sensirion.com/file/datasheet_sht3x_digital
-
-Author:
-
-  - David Frey <david.frey@sensirion.com>
-  - Pascal Sachs <pascal.sachs@sensirion.com>
-
-Description
------------
-
-This driver implements support for the Sensirion SHT3x-DIS chip, a humidity
-and temperature sensor. Temperature is measured in degrees celsius, relative
-humidity is expressed as a percentage. In the sysfs interface, all values are
-scaled by 1000, i.e. the value for 31.5 degrees celsius is 31500.
-
-The device communicates with the I2C protocol. Sensors can have the I2C
-addresses 0x44 or 0x45, depending on the wiring. See
-Documentation/i2c/instantiating-devices for methods to instantiate the device.
-
-There are two options configurable by means of sht3x_platform_data:
-
-1. blocking (pull the I2C clock line down while performing the measurement) or
-   non-blocking mode. Blocking mode will guarantee the fastest result but
-   the I2C bus will be busy during that time. By default, non-blocking mode
-   is used. Make sure clock-stretching works properly on your device if you
-   want to use blocking mode.
-2. high or low accuracy. High accuracy is used by default and using it is
-   strongly recommended.
-
-The sht3x sensor supports a single shot mode as well as 5 periodic measure
-modes, which can be controlled with the update_interval sysfs interface.
-The allowed update_interval in milliseconds are as follows:
-
-    ===== ======= ====================
-       0          single shot mode
-    2000   0.5 Hz periodic measurement
-    1000   1   Hz periodic measurement
-     500   2   Hz periodic measurement
-     250   4   Hz periodic measurement
-     100  10   Hz periodic measurement
-    ===== ======= ====================
-
-In the periodic measure mode, the sensor automatically triggers a measurement
-with the configured update interval on the chip. When a temperature or humidity
-reading exceeds the configured limits, the alert attribute is set to 1 and
-the alert pin on the sensor is set to high.
-When the temperature and humidity readings move back between the hysteresis
-values, the alert bit is set to 0 and the alert pin on the sensor is set to
-low.
-
-sysfs-Interface
----------------
-
-=================== ============================================================
-temp1_input:        temperature input
-humidity1_input:    humidity input
-temp1_max:          temperature max value
-temp1_max_hyst:     temperature hysteresis value for max limit
-humidity1_max:      humidity max value
-humidity1_max_hyst: humidity hysteresis value for max limit
-temp1_min:          temperature min value
-temp1_min_hyst:     temperature hysteresis value for min limit
-humidity1_min:      humidity min value
-humidity1_min_hyst: humidity hysteresis value for min limit
-temp1_alarm:        alarm flag is set to 1 if the temperature is outside the
-		    configured limits. Alarm only works in periodic measure mode
-humidity1_alarm:    alarm flag is set to 1 if the humidity is outside the
-		    configured limits. Alarm only works in periodic measure mode
-heater_enable:      heater enable, heating element removes excess humidity from
-		    sensor:
-
-			- 0: turned off
-			- 1: turned on
-update_interval:    update interval, 0 for single shot, interval in msec
-		    for periodic measurement. If the interval is not supported
-		    by the sensor, the next faster interval is chosen
-=================== ============================================================