Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking updates from David Miller:

 1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
    Augusto von Dentz.

 2) Add GSO partial support to igc, from Sasha Neftin.

 3) Several cleanups and improvements to r8169 from Heiner Kallweit.

 4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
    device self-test. From Andrew Lunn.

 5) Start moving away from custom driver versions, use the globally
    defined kernel version instead, from Leon Romanovsky.

 6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.

 7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.

 8) Add sriov and vf support to hinic, from Luo bin.

 9) Support Media Redundancy Protocol (MRP) in the bridging code, from
    Horatiu Vultur.

10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.

11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
    Dubroca. Also add ipv6 support for espintcp.

12) Lots of ReST conversions of the networking documentation, from Mauro
    Carvalho Chehab.

13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
    from Doug Berger.

14) Allow to dump cgroup id and filter by it in inet_diag code, from
    Dmitry Yakunin.

15) Add infrastructure to export netlink attribute policies to
    userspace, from Johannes Berg.

16) Several optimizations to sch_fq scheduler, from Eric Dumazet.

17) Fallback to the default qdisc if qdisc init fails because otherwise
    a packet scheduler init failure will make a device inoperative. From
    Jesper Dangaard Brouer.

18) Several RISCV bpf jit optimizations, from Luke Nelson.

19) Correct the return type of the ->ndo_start_xmit() method in several
    drivers, it's netdev_tx_t but many drivers were using
    'int'. From Yunjian Wang.

20) Add an ethtool interface for PHY master/slave config, from Oleksij
    Rempel.

21) Add BPF iterators, from Yonghang Song.

22) Add cable test infrastructure, including ethool interfaces, from
    Andrew Lunn. Marvell PHY driver is the first to support this
    facility.

23) Remove zero-length arrays all over, from Gustavo A. R. Silva.

24) Calculate and maintain an explicit frame size in XDP, from Jesper
    Dangaard Brouer.

25) Add CAP_BPF, from Alexei Starovoitov.

26) Support terse dumps in the packet scheduler, from Vlad Buslov.

27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.

28) Add devm_register_netdev(), from Bartosz Golaszewski.

29) Minimize qdisc resets, from Cong Wang.

30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
    eliminate set_fs/get_fs calls. From Christoph Hellwig.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
  selftests: net: ip_defrag: ignore EPERM
  net_failover: fixed rollback in net_failover_open()
  Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
  Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
  vmxnet3: allow rx flow hash ops only when rss is enabled
  hinic: add set_channels ethtool_ops support
  selftests/bpf: Add a default $(CXX) value
  tools/bpf: Don't use $(COMPILE.c)
  bpf, selftests: Use bpf_probe_read_kernel
  s390/bpf: Use bcr 0,%0 as tail call nop filler
  s390/bpf: Maintain 8-byte stack alignment
  selftests/bpf: Fix verifier test
  selftests/bpf: Fix sample_cnt shared between two threads
  bpf, selftests: Adapt cls_redirect to call csum_level helper
  bpf: Add csum_level helper for fixing up csum levels
  bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
  sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
  crypto/chtls: IPv6 support for inline TLS
  Crypto/chcr: Fixes a coccinile check error
  Crypto/chcr: Fixes compilations warnings
  ...

1 files changed, 323 insertions, 0 deletions

diff --git a/Documentation/networking/device_drivers/intel/ipw2100.rst b/Documentation/networking/device_drivers/intel/ipw2100.rst
new file mode 100644
index 000000000000..d54ad522f937
--- /dev/null
+++ b/Documentation/networking/device_drivers/intel/ipw2100.rst
@@ -0,0 +1,323 @@
+.. SPDX-License-Identifier: GPL-2.0
+.. include:: <isonum.txt>
+
+===========================================
+Intel(R) PRO/Wireless 2100 Driver for Linux
+===========================================
+
+Support for:
+
+- Intel(R) PRO/Wireless 2100 Network Connection
+
+Copyright |copy| 2003-2006, Intel Corporation
+
+README.ipw2100
+
+:Version: git-1.1.5
+:Date:    January 25, 2006
+
+.. Index
+
+    0. IMPORTANT INFORMATION BEFORE USING THIS DRIVER
+    1. Introduction
+    2. Release git-1.1.5 Current Features
+    3. Command Line Parameters
+    4. Sysfs Helper Files
+    5. Radio Kill Switch
+    6. Dynamic Firmware
+    7. Power Management
+    8. Support
+    9. License
+
+
+0. IMPORTANT INFORMATION BEFORE USING THIS DRIVER
+=================================================
+
+Important Notice FOR ALL USERS OR DISTRIBUTORS!!!!
+
+Intel wireless LAN adapters are engineered, manufactured, tested, and
+quality checked to ensure that they meet all necessary local and
+governmental regulatory agency requirements for the regions that they
+are designated and/or marked to ship into. Since wireless LANs are
+generally unlicensed devices that share spectrum with radars,
+satellites, and other licensed and unlicensed devices, it is sometimes
+necessary to dynamically detect, avoid, and limit usage to avoid
+interference with these devices. In many instances Intel is required to
+provide test data to prove regional and local compliance to regional and
+governmental regulations before certification or approval to use the
+product is granted. Intel's wireless LAN's EEPROM, firmware, and
+software driver are designed to carefully control parameters that affect
+radio operation and to ensure electromagnetic compliance (EMC). These
+parameters include, without limitation, RF power, spectrum usage,
+channel scanning, and human exposure.
+
+For these reasons Intel cannot permit any manipulation by third parties
+of the software provided in binary format with the wireless WLAN
+adapters (e.g., the EEPROM and firmware). Furthermore, if you use any
+patches, utilities, or code with the Intel wireless LAN adapters that
+have been manipulated by an unauthorized party (i.e., patches,
+utilities, or code (including open source code modifications) which have
+not been validated by Intel), (i) you will be solely responsible for
+ensuring the regulatory compliance of the products, (ii) Intel will bear
+no liability, under any theory of liability for any issues associated
+with the modified products, including without limitation, claims under
+the warranty and/or issues arising from regulatory non-compliance, and
+(iii) Intel will not provide or be required to assist in providing
+support to any third parties for such modified products.
+
+Note: Many regulatory agencies consider Wireless LAN adapters to be
+modules, and accordingly, condition system-level regulatory approval
+upon receipt and review of test data documenting that the antennas and
+system configuration do not cause the EMC and radio operation to be
+non-compliant.
+
+The drivers available for download from SourceForge are provided as a
+part of a development project.  Conformance to local regulatory
+requirements is the responsibility of the individual developer.  As
+such, if you are interested in deploying or shipping a driver as part of
+solution intended to be used for purposes other than development, please
+obtain a tested driver from Intel Customer Support at:
+
+http://www.intel.com/support/wireless/sb/CS-006408.htm
+
+1. Introduction
+===============
+
+This document provides a brief overview of the features supported by the
+IPW2100 driver project.  The main project website, where the latest
+development version of the driver can be found, is:
+
+	http://ipw2100.sourceforge.net
+
+There you can find the not only the latest releases, but also information about
+potential fixes and patches, as well as links to the development mailing list
+for the driver project.
+
+
+2. Release git-1.1.5 Current Supported Features
+===============================================
+
+- Managed (BSS) and Ad-Hoc (IBSS)
+- WEP (shared key and open)
+- Wireless Tools support
+- 802.1x (tested with XSupplicant 1.0.1)
+
+Enabled (but not supported) features:
+- Monitor/RFMon mode
+- WPA/WPA2
+
+The distinction between officially supported and enabled is a reflection
+on the amount of validation and interoperability testing that has been
+performed on a given feature.
+
+
+3. Command Line Parameters
+==========================
+
+If the driver is built as a module, the following optional parameters are used
+by entering them on the command line with the modprobe command using this
+syntax::
+
+	modprobe ipw2100 [<option>=<VAL1><,VAL2>...]
+
+For example, to disable the radio on driver loading, enter:
+
+	modprobe ipw2100 disable=1
+
+The ipw2100 driver supports the following module parameters:
+
+=========	==============	============  ==============================
+Name		Value		Example       Meaning
+=========	==============	============  ==============================
+debug		0x0-0xffffffff	debug=1024    Debug level set to 1024
+mode		0,1,2		mode=1        AdHoc
+channel		int		channel=3     Only valid in AdHoc or Monitor
+associate	boolean		associate=0   Do NOT auto associate
+disable		boolean		disable=1     Do not power the HW
+=========	==============	============  ==============================
+
+
+4. Sysfs Helper Files
+=====================
+
+There are several ways to control the behavior of the driver.  Many of the
+general capabilities are exposed through the Wireless Tools (iwconfig).  There
+are a few capabilities that are exposed through entries in the Linux Sysfs.
+
+
+**Driver Level**
+
+For the driver level files, look in /sys/bus/pci/drivers/ipw2100/
+
+  debug_level
+	This controls the same global as the 'debug' module parameter.  For
+	information on the various debugging levels available, run the 'dvals'
+	script found in the driver source directory.
+
+	.. note::
+
+	      'debug_level' is only enabled if CONFIG_IPW2100_DEBUG is turn on.
+
+**Device Level**
+
+For the device level files look in::
+
+	/sys/bus/pci/drivers/ipw2100/{PCI-ID}/
+
+For example::
+
+	/sys/bus/pci/drivers/ipw2100/0000:02:01.0
+
+For the device level files, see /sys/bus/pci/drivers/ipw2100:
+
+  rf_kill
+	read
+
+	==  =========================================
+	0   RF kill not enabled (radio on)
+	1   SW based RF kill active (radio off)
+	2   HW based RF kill active (radio off)
+	3   Both HW and SW RF kill active (radio off)
+	==  =========================================
+
+	write
+
+	==  ==================================================
+	0   If SW based RF kill active, turn the radio back on
+	1   If radio is on, activate SW based RF kill
+	==  ==================================================
+
+	.. note::
+
+	   If you enable the SW based RF kill and then toggle the HW
+	   based RF kill from ON -> OFF -> ON, the radio will NOT come back on
+
+
+5. Radio Kill Switch
+====================
+
+Most laptops provide the ability for the user to physically disable the radio.
+Some vendors have implemented this as a physical switch that requires no
+software to turn the radio off and on.  On other laptops, however, the switch
+is controlled through a button being pressed and a software driver then making
+calls to turn the radio off and on.  This is referred to as a "software based
+RF kill switch"
+
+See the Sysfs helper file 'rf_kill' for determining the state of the RF switch
+on your system.
+
+
+6. Dynamic Firmware
+===================
+
+As the firmware is licensed under a restricted use license, it can not be
+included within the kernel sources.  To enable the IPW2100 you will need a
+firmware image to load into the wireless NIC's processors.
+
+You can obtain these images from <http://ipw2100.sf.net/firmware.php>.
+
+See INSTALL for instructions on installing the firmware.
+
+
+7. Power Management
+===================
+
+The IPW2100 supports the configuration of the Power Save Protocol
+through a private wireless extension interface.  The IPW2100 supports
+the following different modes:
+
+	===	===========================================================
+	off	No power management.  Radio is always on.
+	on	Automatic power management
+	1-5	Different levels of power management.  The higher the
+		number the greater the power savings, but with an impact to
+		packet latencies.
+	===	===========================================================
+
+Power management works by powering down the radio after a certain
+interval of time has passed where no packets are passed through the
+radio.  Once powered down, the radio remains in that state for a given
+period of time.  For higher power savings, the interval between last
+packet processed to sleep is shorter and the sleep period is longer.
+
+When the radio is asleep, the access point sending data to the station
+must buffer packets at the AP until the station wakes up and requests
+any buffered packets.  If you have an AP that does not correctly support
+the PSP protocol you may experience packet loss or very poor performance
+while power management is enabled.  If this is the case, you will need
+to try and find a firmware update for your AP, or disable power
+management (via ``iwconfig eth1 power off``)
+
+To configure the power level on the IPW2100 you use a combination of
+iwconfig and iwpriv.  iwconfig is used to turn power management on, off,
+and set it to auto.
+
+	=========================  ====================================
+	iwconfig eth1 power off    Disables radio power down
+	iwconfig eth1 power on     Enables radio power management to
+				   last set level (defaults to AUTO)
+	iwpriv eth1 set_power 0    Sets power level to AUTO and enables
+				   power management if not previously
+				   enabled.
+	iwpriv eth1 set_power 1-5  Set the power level as specified,
+				   enabling power management if not
+				   previously enabled.
+	=========================  ====================================
+
+You can view the current power level setting via::
+
+	iwpriv eth1 get_power
+
+It will return the current period or timeout that is configured as a string
+in the form of xxxx/yyyy (z) where xxxx is the timeout interval (amount of
+time after packet processing), yyyy is the period to sleep (amount of time to
+wait before powering the radio and querying the access point for buffered
+packets), and z is the 'power level'.  If power management is turned off the
+xxxx/yyyy will be replaced with 'off' -- the level reported will be the active
+level if `iwconfig eth1 power on` is invoked.
+
+
+8. Support
+==========
+
+For general development information and support,
+go to:
+
+    http://ipw2100.sf.net/
+
+The ipw2100 1.1.0 driver and firmware can be downloaded from:
+
+    http://support.intel.com
+
+For installation support on the ipw2100 1.1.0 driver on Linux kernels
+2.6.8 or greater, email support is available from:
+
+    http://supportmail.intel.com
+
+9. License
+==========
+
+  Copyright |copy| 2003 - 2006 Intel Corporation. All rights reserved.
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms of the GNU General Public License (version 2) as
+  published by the Free Software Foundation.
+
+  This program is distributed in the hope that it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc., 59
+  Temple Place - Suite 330, Boston, MA  02111-1307, USA.
+
+  The full GNU General Public License is included in this distribution in the
+  file called LICENSE.
+
+  License Contact Information:
+
+  James P. Ketrenos <ipw2100-admin@linux.intel.com>
+
+  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+