Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking updates from David Miller:

 1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
    Augusto von Dentz.

 2) Add GSO partial support to igc, from Sasha Neftin.

 3) Several cleanups and improvements to r8169 from Heiner Kallweit.

 4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
    device self-test. From Andrew Lunn.

 5) Start moving away from custom driver versions, use the globally
    defined kernel version instead, from Leon Romanovsky.

 6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.

 7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.

 8) Add sriov and vf support to hinic, from Luo bin.

 9) Support Media Redundancy Protocol (MRP) in the bridging code, from
    Horatiu Vultur.

10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.

11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
    Dubroca. Also add ipv6 support for espintcp.

12) Lots of ReST conversions of the networking documentation, from Mauro
    Carvalho Chehab.

13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
    from Doug Berger.

14) Allow to dump cgroup id and filter by it in inet_diag code, from
    Dmitry Yakunin.

15) Add infrastructure to export netlink attribute policies to
    userspace, from Johannes Berg.

16) Several optimizations to sch_fq scheduler, from Eric Dumazet.

17) Fallback to the default qdisc if qdisc init fails because otherwise
    a packet scheduler init failure will make a device inoperative. From
    Jesper Dangaard Brouer.

18) Several RISCV bpf jit optimizations, from Luke Nelson.

19) Correct the return type of the ->ndo_start_xmit() method in several
    drivers, it's netdev_tx_t but many drivers were using
    'int'. From Yunjian Wang.

20) Add an ethtool interface for PHY master/slave config, from Oleksij
    Rempel.

21) Add BPF iterators, from Yonghang Song.

22) Add cable test infrastructure, including ethool interfaces, from
    Andrew Lunn. Marvell PHY driver is the first to support this
    facility.

23) Remove zero-length arrays all over, from Gustavo A. R. Silva.

24) Calculate and maintain an explicit frame size in XDP, from Jesper
    Dangaard Brouer.

25) Add CAP_BPF, from Alexei Starovoitov.

26) Support terse dumps in the packet scheduler, from Vlad Buslov.

27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.

28) Add devm_register_netdev(), from Bartosz Golaszewski.

29) Minimize qdisc resets, from Cong Wang.

30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
    eliminate set_fs/get_fs calls. From Christoph Hellwig.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
  selftests: net: ip_defrag: ignore EPERM
  net_failover: fixed rollback in net_failover_open()
  Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
  Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
  vmxnet3: allow rx flow hash ops only when rss is enabled
  hinic: add set_channels ethtool_ops support
  selftests/bpf: Add a default $(CXX) value
  tools/bpf: Don't use $(COMPILE.c)
  bpf, selftests: Use bpf_probe_read_kernel
  s390/bpf: Use bcr 0,%0 as tail call nop filler
  s390/bpf: Maintain 8-byte stack alignment
  selftests/bpf: Fix verifier test
  selftests/bpf: Fix sample_cnt shared between two threads
  bpf, selftests: Adapt cls_redirect to call csum_level helper
  bpf: Add csum_level helper for fixing up csum levels
  bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
  sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
  crypto/chtls: IPv6 support for inline TLS
  Crypto/chcr: Fixes a coccinile check error
  Crypto/chcr: Fixes compilations warnings
  ...

1 files changed, 0 insertions, 207 deletions

diff --git a/Documentation/networking/device_drivers/sb1000.txt b/Documentation/networking/device_drivers/sb1000.txt
deleted file mode 100644
index f92c2aac56a9..000000000000
--- a/Documentation/networking/device_drivers/sb1000.txt
+++ /dev/null
@@ -1,207 +0,0 @@
-sb1000 is a module network device driver for the General Instrument (also known
-as NextLevel) SURFboard1000 internal cable modem board.  This is an ISA card
-which is used by a number of cable TV companies to provide cable modem access.
-It's a one-way downstream-only cable modem, meaning that your upstream net link
-is provided by your regular phone modem.
-
-This driver was written by Franco Venturi <fventuri@mediaone.net>.  He deserves
-a great deal of thanks for this wonderful piece of code!
-
------------------------------------------------------------------------------
-
-Support for this device is now a part of the standard Linux kernel.  The
-driver source code file is drivers/net/sb1000.c.  In addition to this
-you will need:
-
-1.) The "cmconfig" program.  This is a utility which supplements "ifconfig"
-to configure the cable modem and network interface (usually called "cm0");
-and
-
-2.) Several PPP scripts which live in /etc/ppp to make connecting via your
-cable modem easy.
-
-   These utilities can be obtained from:
-
-      http://www.jacksonville.net/~fventuri/
-
-   in Franco's original source code distribution .tar.gz file.  Support for
-   the sb1000 driver can be found at:
-
-      http://web.archive.org/web/*/http://home.adelphia.net/~siglercm/sb1000.html
-      http://web.archive.org/web/*/http://linuxpower.cx/~cable/
-
-   along with these utilities.
-
-3.) The standard isapnp tools.  These are necessary to configure your SB1000
-card at boot time (or afterwards by hand) since it's a PnP card.
-
-   If you don't have these installed as a standard part of your Linux
-   distribution, you can find them at:
-
-      http://www.roestock.demon.co.uk/isapnptools/
-
-   or check your Linux distribution binary CD or their web site.  For help with
-   isapnp, pnpdump, or /etc/isapnp.conf, go to:
-
-      http://www.roestock.demon.co.uk/isapnptools/isapnpfaq.html
-
------------------------------------------------------------------------------
-
-To make the SB1000 card work, follow these steps:
-
-1.) Run `make config', or `make menuconfig', or `make xconfig', whichever
-you prefer, in the top kernel tree directory to set up your kernel
-configuration.  Make sure to say "Y" to "Prompt for development drivers"
-and to say "M" to the sb1000 driver.  Also say "Y" or "M" to all the standard
-networking questions to get TCP/IP and PPP networking support.
-
-2.) *BEFORE* you build the kernel, edit drivers/net/sb1000.c.  Make sure
-to redefine the value of READ_DATA_PORT to match the I/O address used
-by isapnp to access your PnP cards.  This is the value of READPORT in
-/etc/isapnp.conf or given by the output of pnpdump.
-
-3.) Build and install the kernel and modules as usual.
-
-4.) Boot your new kernel following the usual procedures.
-
-5.) Set up to configure the new SB1000 PnP card by capturing the output
-of "pnpdump" to a file and editing this file to set the correct I/O ports,
-IRQ, and DMA settings for all your PnP cards.  Make sure none of the settings
-conflict with one another.  Then test this configuration by running the
-"isapnp" command with your new config file as the input.  Check for
-errors and fix as necessary.  (As an aside, I use I/O ports 0x110 and
-0x310 and IRQ 11 for my SB1000 card and these work well for me.  YMMV.)
-Then save the finished config file as /etc/isapnp.conf for proper configuration
-on subsequent reboots.
-
-6.) Download the original file sb1000-1.1.2.tar.gz from Franco's site or one of
-the others referenced above.  As root, unpack it into a temporary directory and
-do a `make cmconfig' and then `install -c cmconfig /usr/local/sbin'.  Don't do
-`make install' because it expects to find all the utilities built and ready for
-installation, not just cmconfig.
-
-7.) As root, copy all the files under the ppp/ subdirectory in Franco's
-tar file into /etc/ppp, being careful not to overwrite any files that are
-already in there.  Then modify ppp@gi-on to set the correct login name,
-phone number, and frequency for the cable modem.  Also edit pap-secrets
-to specify your login name and password and any site-specific information
-you need.
-
-8.) Be sure to modify /etc/ppp/firewall to use ipchains instead of
-the older ipfwadm commands from the 2.0.x kernels.  There's a neat utility to
-convert ipfwadm commands to ipchains commands:
-
-   http://users.dhp.com/~whisper/ipfwadm2ipchains/
-
-You may also wish to modify the firewall script to implement a different
-firewalling scheme.
-
-9.) Start the PPP connection via the script /etc/ppp/ppp@gi-on.  You must be
-root to do this.  It's better to use a utility like sudo to execute
-frequently used commands like this with root permissions if possible.  If you
-connect successfully the cable modem interface will come up and you'll see a
-driver message like this at the console:
-
-         cm0: sb1000 at (0x110,0x310), csn 1, S/N 0x2a0d16d8, IRQ 11.
-         sb1000.c:v1.1.2 6/01/98 (fventuri@mediaone.net)
-
-The "ifconfig" command should show two new interfaces, ppp0 and cm0.
-The command "cmconfig cm0" will give you information about the cable modem
-interface.
-
-10.) Try pinging a site via `ping -c 5 www.yahoo.com', for example.  You should
-see packets received.
-
-11.) If you can't get site names (like www.yahoo.com) to resolve into
-IP addresses (like 204.71.200.67), be sure your /etc/resolv.conf file
-has no syntax errors and has the right nameserver IP addresses in it.
-If this doesn't help, try something like `ping -c 5 204.71.200.67' to
-see if the networking is running but the DNS resolution is where the
-problem lies.
-
-12.) If you still have problems, go to the support web sites mentioned above
-and read the information and documentation there.
-
------------------------------------------------------------------------------
-
-Common problems:
-
-1.) Packets go out on the ppp0 interface but don't come back on the cm0
-interface.  It looks like I'm connected but I can't even ping any
-numerical IP addresses.  (This happens predominantly on Debian systems due
-to a default boot-time configuration script.)
-
-Solution -- As root `echo 0 > /proc/sys/net/ipv4/conf/cm0/rp_filter' so it
-can share the same IP address as the ppp0 interface.  Note that this
-command should probably be added to the /etc/ppp/cablemodem script
-*right*between* the "/sbin/ifconfig" and "/sbin/cmconfig" commands.
-You may need to do this to /proc/sys/net/ipv4/conf/ppp0/rp_filter as well.
-If you do this to /proc/sys/net/ipv4/conf/default/rp_filter on each reboot
-(in rc.local or some such) then any interfaces can share the same IP
-addresses.
-
-2.) I get "unresolved symbol" error messages on executing `insmod sb1000.o'.
-
-Solution -- You probably have a non-matching kernel source tree and
-/usr/include/linux and /usr/include/asm header files.  Make sure you
-install the correct versions of the header files in these two directories.
-Then rebuild and reinstall the kernel.
-
-3.) When isapnp runs it reports an error, and my SB1000 card isn't working.
-
-Solution -- There's a problem with later versions of isapnp using the "(CHECK)"
-option in the lines that allocate the two I/O addresses for the SB1000 card.
-This first popped up on RH 6.0.  Delete "(CHECK)" for the SB1000 I/O addresses.
-Make sure they don't conflict with any other pieces of hardware first!  Then
-rerun isapnp and go from there.
-
-4.) I can't execute the /etc/ppp/ppp@gi-on file.
-
-Solution -- As root do `chmod ug+x /etc/ppp/ppp@gi-on'.
-
-5.) The firewall script isn't working (with 2.2.x and higher kernels).
-
-Solution -- Use the ipfwadm2ipchains script referenced above to convert the
-/etc/ppp/firewall script from the deprecated ipfwadm commands to ipchains.
-
-6.) I'm getting *tons* of firewall deny messages in the /var/kern.log,
-/var/messages, and/or /var/syslog files, and they're filling up my /var
-partition!!!
-
-Solution -- First, tell your ISP that you're receiving DoS (Denial of Service)
-and/or portscanning (UDP connection attempts) attacks!  Look over the deny
-messages to figure out what the attack is and where it's coming from.  Next,
-edit /etc/ppp/cablemodem and make sure the ",nobroadcast" option is turned on
-to the "cmconfig" command (uncomment that line).  If you're not receiving these
-denied packets on your broadcast interface (IP address xxx.yyy.zzz.255
-typically), then someone is attacking your machine in particular.  Be careful
-out there....
-
-7.) Everything seems to work fine but my computer locks up after a while
-(and typically during a lengthy download through the cable modem)!
-
-Solution -- You may need to add a short delay in the driver to 'slow down' the
-SURFboard because your PC might not be able to keep up with the transfer rate
-of the SB1000. To do this, it's probably best to download Franco's
-sb1000-1.1.2.tar.gz archive and build and install sb1000.o manually.  You'll
-want to edit the 'Makefile' and look for the 'SB1000_DELAY'
-define.  Uncomment those 'CFLAGS' lines (and comment out the default ones)
-and try setting the delay to something like 60 microseconds with:
-'-DSB1000_DELAY=60'.  Then do `make' and as root `make install' and try
-it out.  If it still doesn't work or you like playing with the driver, you may
-try other numbers.  Remember though that the higher the delay, the slower the
-driver (which slows down the rest of the PC too when it is actively
-used). Thanks to Ed Daiga for this tip!
-
------------------------------------------------------------------------------
-
-Credits:  This README came from Franco Venturi's original README file which is
-still supplied with his driver .tar.gz archive.  I and all other sb1000 users
-owe Franco a tremendous "Thank you!"  Additional thanks goes to Carl Patten
-and Ralph Bonnell who are now managing the Linux SB1000 web site, and to
-the SB1000 users who reported and helped debug the common problems listed
-above.
-
-
-					Clemmitt Sigler
-					csigler@vt.edu