Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking updates from David Miller:

 1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
    Augusto von Dentz.

 2) Add GSO partial support to igc, from Sasha Neftin.

 3) Several cleanups and improvements to r8169 from Heiner Kallweit.

 4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
    device self-test. From Andrew Lunn.

 5) Start moving away from custom driver versions, use the globally
    defined kernel version instead, from Leon Romanovsky.

 6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.

 7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.

 8) Add sriov and vf support to hinic, from Luo bin.

 9) Support Media Redundancy Protocol (MRP) in the bridging code, from
    Horatiu Vultur.

10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.

11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
    Dubroca. Also add ipv6 support for espintcp.

12) Lots of ReST conversions of the networking documentation, from Mauro
    Carvalho Chehab.

13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
    from Doug Berger.

14) Allow to dump cgroup id and filter by it in inet_diag code, from
    Dmitry Yakunin.

15) Add infrastructure to export netlink attribute policies to
    userspace, from Johannes Berg.

16) Several optimizations to sch_fq scheduler, from Eric Dumazet.

17) Fallback to the default qdisc if qdisc init fails because otherwise
    a packet scheduler init failure will make a device inoperative. From
    Jesper Dangaard Brouer.

18) Several RISCV bpf jit optimizations, from Luke Nelson.

19) Correct the return type of the ->ndo_start_xmit() method in several
    drivers, it's netdev_tx_t but many drivers were using
    'int'. From Yunjian Wang.

20) Add an ethtool interface for PHY master/slave config, from Oleksij
    Rempel.

21) Add BPF iterators, from Yonghang Song.

22) Add cable test infrastructure, including ethool interfaces, from
    Andrew Lunn. Marvell PHY driver is the first to support this
    facility.

23) Remove zero-length arrays all over, from Gustavo A. R. Silva.

24) Calculate and maintain an explicit frame size in XDP, from Jesper
    Dangaard Brouer.

25) Add CAP_BPF, from Alexei Starovoitov.

26) Support terse dumps in the packet scheduler, from Vlad Buslov.

27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.

28) Add devm_register_netdev(), from Bartosz Golaszewski.

29) Minimize qdisc resets, from Cong Wang.

30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
    eliminate set_fs/get_fs calls. From Christoph Hellwig.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
  selftests: net: ip_defrag: ignore EPERM
  net_failover: fixed rollback in net_failover_open()
  Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
  Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
  vmxnet3: allow rx flow hash ops only when rss is enabled
  hinic: add set_channels ethtool_ops support
  selftests/bpf: Add a default $(CXX) value
  tools/bpf: Don't use $(COMPILE.c)
  bpf, selftests: Use bpf_probe_read_kernel
  s390/bpf: Use bcr 0,%0 as tail call nop filler
  s390/bpf: Maintain 8-byte stack alignment
  selftests/bpf: Fix verifier test
  selftests/bpf: Fix sample_cnt shared between two threads
  bpf, selftests: Adapt cls_redirect to call csum_level helper
  bpf: Add csum_level helper for fixing up csum levels
  bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
  sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
  crypto/chtls: IPv6 support for inline TLS
  Crypto/chcr: Fixes a coccinile check error
  Crypto/chcr: Fixes compilations warnings
  ...

1 files changed, 140 insertions, 0 deletions

diff --git a/Documentation/networking/device_drivers/ti/tlan.rst b/Documentation/networking/device_drivers/ti/tlan.rst
new file mode 100644
index 000000000000..4fdc0907f4fc
--- /dev/null
+++ b/Documentation/networking/device_drivers/ti/tlan.rst
@@ -0,0 +1,140 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+=====================
+TLAN driver for Linux
+=====================
+
+:Version: 1.14a
+
+(C) 1997-1998 Caldera, Inc.
+
+(C) 1998 James Banks
+
+(C) 1999-2001 Torben Mathiasen <tmm@image.dk, torben.mathiasen@compaq.com>
+
+For driver information/updates visit http://www.compaq.com
+
+
+
+
+
+I. Supported Devices
+====================
+
+    Only PCI devices will work with this driver.
+
+    Supported:
+
+    =========	=========	===========================================
+    Vendor ID	Device ID	Name
+    =========	=========	===========================================
+    0e11	ae32		Compaq Netelligent 10/100 TX PCI UTP
+    0e11	ae34		Compaq Netelligent 10 T PCI UTP
+    0e11	ae35		Compaq Integrated NetFlex 3/P
+    0e11	ae40		Compaq Netelligent Dual 10/100 TX PCI UTP
+    0e11	ae43		Compaq Netelligent Integrated 10/100 TX UTP
+    0e11	b011		Compaq Netelligent 10/100 TX Embedded UTP
+    0e11	b012		Compaq Netelligent 10 T/2 PCI UTP/Coax
+    0e11	b030		Compaq Netelligent 10/100 TX UTP
+    0e11	f130		Compaq NetFlex 3/P
+    0e11	f150		Compaq NetFlex 3/P
+    108d	0012		Olicom OC-2325
+    108d	0013		Olicom OC-2183
+    108d	0014		Olicom OC-2326
+    =========	=========	===========================================
+
+
+    Caveats:
+
+    I am not sure if 100BaseTX daughterboards (for those cards which
+    support such things) will work.  I haven't had any solid evidence
+    either way.
+
+    However, if a card supports 100BaseTx without requiring an add
+    on daughterboard, it should work with 100BaseTx.
+
+    The "Netelligent 10 T/2 PCI UTP/Coax" (b012) device is untested,
+    but I do not expect any problems.
+
+
+II. Driver Options
+==================
+
+	1. You can append debug=x to the end of the insmod line to get
+	   debug messages, where x is a bit field where the bits mean
+	   the following:
+
+	   ====		=====================================
+	   0x01		Turn on general debugging messages.
+	   0x02		Turn on receive debugging messages.
+	   0x04		Turn on transmit debugging messages.
+	   0x08		Turn on list debugging messages.
+	   ====		=====================================
+
+	2. You can append aui=1 to the end of the insmod line to cause
+	   the adapter to use the AUI interface instead of the 10 Base T
+	   interface.  This is also what to do if you want to use the BNC
+	   connector on a TLAN based device.  (Setting this option on a
+	   device that does not have an AUI/BNC connector will probably
+	   cause it to not function correctly.)
+
+	3. You can set duplex=1 to force half duplex, and duplex=2 to
+	   force full duplex.
+
+	4. You can set speed=10 to force 10Mbs operation, and speed=100
+	   to force 100Mbs operation. (I'm not sure what will happen
+	   if a card which only supports 10Mbs is forced into 100Mbs
+	   mode.)
+
+	5. You have to use speed=X duplex=Y together now. If you just
+	   do "insmod tlan.o speed=100" the driver will do Auto-Neg.
+	   To force a 10Mbps Half-Duplex link do "insmod tlan.o speed=10
+	   duplex=1".
+
+	6. If the driver is built into the kernel, you can use the 3rd
+	   and 4th parameters to set aui and debug respectively.  For
+	   example::
+
+		ether=0,0,0x1,0x7,eth0
+
+	   This sets aui to 0x1 and debug to 0x7, assuming eth0 is a
+	   supported TLAN device.
+
+	   The bits in the third byte are assigned as follows:
+
+		====   ===============
+		0x01   aui
+		0x02   use half duplex
+		0x04   use full duplex
+		0x08   use 10BaseT
+		0x10   use 100BaseTx
+		====   ===============
+
+	   You also need to set both speed and duplex settings when forcing
+	   speeds with kernel-parameters.
+	   ether=0,0,0x12,0,eth0 will force link to 100Mbps Half-Duplex.
+
+	7. If you have more than one tlan adapter in your system, you can
+	   use the above options on a per adapter basis. To force a 100Mbit/HD
+	   link with your eth1 adapter use::
+
+		insmod tlan speed=0,100 duplex=0,1
+
+	   Now eth0 will use auto-neg and eth1 will be forced to 100Mbit/HD.
+	   Note that the tlan driver supports a maximum of 8 adapters.
+
+
+III. Things to try if you have problems
+=======================================
+
+	1. Make sure your card's PCI id is among those listed in
+	   section I, above.
+	2. Make sure routing is correct.
+	3. Try forcing different speed/duplex settings
+
+
+There is also a tlan mailing list which you can join by sending "subscribe tlan"
+in the body of an email to majordomo@vuser.vu.union.edu.
+
+There is also a tlan website at http://www.compaq.com
+