Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
  qlcnic: adding co maintainer
  ixgbe: add support for active DA cables
  ixgbe: dcb, do not tag tc_prio_control frames
  ixgbe: fix ixgbe_tx_is_paused logic
  ixgbe: always enable vlan strip/insert when DCB is enabled
  ixgbe: remove some redundant code in setting FCoE FIP filter
  ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
  ixgbe: fix header len when unsplit packet overflows to data buffer
  ipv6: Never schedule DAD timer on dead address
  ipv6: Use POSTDAD state
  ipv6: Use state_lock to protect ifa state
  ipv6: Replace inet6_ifaddr->dead with state
  cxgb4: notify upper drivers if the device is already up when they load
  cxgb4: keep interrupts available when the ports are brought down
  cxgb4: fix initial addition of MAC address
  cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
  cnic: Convert cnic_local_flags to atomic ops.
  can: Fix SJA1000 command register writes on SMP systems
  bridge: fix build for CONFIG_SYSFS disabled
  ARCNET: Limit com20020 PCI ID matches for SOHARD cards
  ...

Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).

Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c

1 files changed, 8 insertions, 8 deletions

diff --git a/Documentation/networking/x25-iface.txt b/Documentation/networking/x25-iface.txt
index 975cc87ebdd1..78f662ee0622 100644
--- a/Documentation/networking/x25-iface.txt
+++ b/Documentation/networking/x25-iface.txt
@@ -20,23 +20,23 @@ the rest of the skbuff, if any more information does exist.
 Packet Layer to Device Driver
 -----------------------------
 
-First Byte = 0x00
+First Byte = 0x00 (X25_IFACE_DATA)
 
 This indicates that the rest of the skbuff contains data to be transmitted
 over the LAPB link. The LAPB link should already exist before any data is
 passed down.
 
-First Byte = 0x01
+First Byte = 0x01 (X25_IFACE_CONNECT)
 
 Establish the LAPB link. If the link is already established then the connect
 confirmation message should be returned as soon as possible.
 
-First Byte = 0x02
+First Byte = 0x02 (X25_IFACE_DISCONNECT)
 
 Terminate the LAPB link. If it is already disconnected then the disconnect
 confirmation message should be returned as soon as possible.
 
-First Byte = 0x03
+First Byte = 0x03 (X25_IFACE_PARAMS)
 
 LAPB parameters. To be defined.
 
@@ -44,22 +44,22 @@ LAPB parameters. To be defined.
 Device Driver to Packet Layer
 -----------------------------
 
-First Byte = 0x00
+First Byte = 0x00 (X25_IFACE_DATA)
 
 This indicates that the rest of the skbuff contains data that has been
 received over the LAPB link.
 
-First Byte = 0x01
+First Byte = 0x01 (X25_IFACE_CONNECT)
 
 LAPB link has been established. The same message is used for both a LAPB
 link connect_confirmation and a connect_indication.
 
-First Byte = 0x02
+First Byte = 0x02 (X25_IFACE_DISCONNECT)
 
 LAPB link has been terminated. This same message is used for both a LAPB
 link disconnect_confirmation and a disconnect_indication.
 
-First Byte = 0x03
+First Byte = 0x03 (X25_IFACE_PARAMS)
 
 LAPB parameters. To be defined.