Merge branch 'linus' into release

Conflicts:
	arch/x86/kernel/acpi/sleep.c

Signed-off-by: Len Brown <len.brown@intel.com>

3 files changed, 59 insertions, 1 deletions

diff --git a/Documentation/scsi/ChangeLog.megaraid_sas b/Documentation/scsi/ChangeLog.megaraid_sas
index b64d10d221ec..4d9ce73ff730 100644
--- a/Documentation/scsi/ChangeLog.megaraid_sas
+++ b/Documentation/scsi/ChangeLog.megaraid_sas
@@ -1,3 +1,26 @@
+Release Date    : Thu. Feb 24, 2011 17:00:00 PST 2010 -
+			(emaild-id:megaraidlinux@lsi.com)
+			Adam Radford
+Current Version : 00.00.05.34-rc1
+Old Version     : 00.00.05.29-rc1
+    1. Fix some failure gotos from megasas_probe_one(), etc.
+    2. Add missing check_and_restore_queue_depth() call in
+       complete_cmd_fusion().
+    3. Enable MSI-X before calling megasas_init_fw().
+    4. Call tasklet_schedule() even if outbound_intr_status == 0 for MFI based
+       boards in MSI-X mode.
+    5. Fix megasas_probe_one() to clear PCI_MSIX_FLAGS_ENABLE in msi control
+       register in kdump kernel.
+    6. Fix megasas_get_cmd() to only print "Command pool empty" if
+       megasas_dbg_lvl is set.
+    7. Fix megasas_build_dcdb_fusion() to not filter by TYPE_DISK.
+    8. Fix megasas_build_dcdb_fusion() to use io_request->LUN[1] field.
+    9. Add MR_EVT_CFG_CLEARED to megasas_aen_polling().
+    10. Fix tasklet_init() in megasas_init_fw() to use instancet->tasklet.
+    11. Fix fault state handling in megasas_transition_to_ready().
+    12. Fix max_sectors setting for IEEE SGL's.
+    13. Fix iMR OCR support to work correctly.
+-------------------------------------------------------------------------------
 Release Date    : Tues.  Dec 14, 2010 17:00:00 PST 2010 -
 			(emaild-id:megaraidlinux@lsi.com)
 			Adam Radford
diff --git a/Documentation/scsi/hpsa.txt b/Documentation/scsi/hpsa.txt
index dca658362cbf..891435a72fce 100644
--- a/Documentation/scsi/hpsa.txt
+++ b/Documentation/scsi/hpsa.txt
@@ -28,6 +28,12 @@ boot parameter "hpsa_allow_any=1" is specified, however these are not tested
 nor supported by HP with this driver.  For older Smart Arrays, the cciss
 driver should still be used.
 
+The "hpsa_simple_mode=1" boot parameter may be used to prevent the driver from
+putting the controller into "performant" mode.  The difference is that with simple
+mode, each command completion requires an interrupt, while with "performant mode"
+(the default, and ordinarily better performing) it is possible to have multiple
+command completions indicated by a single interrupt.
+
 HPSA specific entries in /sys
 -----------------------------
 
@@ -39,6 +45,8 @@ HPSA specific entries in /sys
 
   /sys/class/scsi_host/host*/rescan
   /sys/class/scsi_host/host*/firmware_revision
+  /sys/class/scsi_host/host*/resettable
+  /sys/class/scsi_host/host*/transport_mode
 
   the host "rescan" attribute is a write only attribute.  Writing to this
   attribute will cause the driver to scan for new, changed, or removed devices
@@ -55,6 +63,21 @@ HPSA specific entries in /sys
 	root@host:/sys/class/scsi_host/host4# cat firmware_revision
 	7.14
 
+  The transport_mode indicates whether the controller is in "performant"
+  or "simple" mode.  This is controlled by the "hpsa_simple_mode" module
+  parameter.
+
+  The "resettable" read-only attribute indicates whether a particular
+  controller is able to honor the "reset_devices" kernel parameter.  If the
+  device is resettable, this file will contain a "1", otherwise, a "0".  This
+  parameter is used by kdump, for example, to reset the controller at driver
+  load time to eliminate any outstanding commands on the controller and get the
+  controller into a known state so that the kdump initiated i/o will work right
+  and not be disrupted in any way by stale commands or other stale state
+  remaining on the controller from the previous kernel.  This attribute enables
+  kexec tools to warn the user if they attempt to designate a device which is
+  unable to honor the reset_devices kernel parameter as a dump device.
+
   HPSA specific disk attributes:
   ------------------------------
 
diff --git a/Documentation/scsi/scsi_mid_low_api.txt b/Documentation/scsi/scsi_mid_low_api.txt
index df322c103466..5f17d29c59b5 100644
--- a/Documentation/scsi/scsi_mid_low_api.txt
+++ b/Documentation/scsi/scsi_mid_low_api.txt
@@ -1343,7 +1343,7 @@ Members of interest:
                    underruns (overruns should be rare). If possible an LLD
                    should set 'resid' prior to invoking 'done'. The most
                    interesting case is data transfers from a SCSI target
-                   device device (i.e. READs) that underrun. 
+                   device (e.g. READs) that underrun.
     underflow    - LLD should place (DID_ERROR << 16) in 'result' if
                    actual number of bytes transferred is less than this
                    figure. Not many LLDs implement this check and some that
@@ -1351,6 +1351,18 @@ Members of interest:
                    report a DID_ERROR. Better for an LLD to implement
                    'resid'.
 
+It is recommended that a LLD set 'resid' on data transfers from a SCSI
+target device (e.g. READs). It is especially important that 'resid' is set
+when such data transfers have sense keys of MEDIUM ERROR and HARDWARE ERROR
+(and possibly RECOVERED ERROR). In these cases if a LLD is in doubt how much
+data has been received then the safest approach is to indicate no bytes have
+been received. For example: to indicate that no valid data has been received
+a LLD might use these helpers:
+    scsi_set_resid(SCpnt, scsi_bufflen(SCpnt));
+where 'SCpnt' is a pointer to a scsi_cmnd object. To indicate only three 512
+bytes blocks has been received 'resid' could be set like this:
+    scsi_set_resid(SCpnt, scsi_bufflen(SCpnt) - (3 * 512));
+
 The scsi_cmnd structure is defined in include/scsi/scsi_cmnd.h