Merge tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
 "A respun version of the merges for the pull request previously sent
  with a few additional fixes.  The last two merges were fixed up by
  hand since the branches have moved on and currently have the prior
  merge in them.

  Quite a busy release for the SPI subsystem, mostly in cleanups big and
  small scattered through the stack rather than anything else:

   - New driver for the Broadcom BC63xx HSSPI controller
   - Fix duplicate device registration for ACPI
   - Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA
     changes upon which the transiton depends)
   - Some small optimisations to reduce the amount of time we hold locks
     in the datapath, eliminate some redundant checks and the size of a
     spi_transfer
   - Lots of fixes, cleanups and general enhancements to drivers,
     especially the rspi and Atmel drivers"

* tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (112 commits)
  spi: core: Fix transfer failure when master->transfer_one returns positive value
  spi: Correct set_cs() documentation
  spi: Clarify transfer_one() w.r.t. spi_finalize_current_transfer()
  spi: Spelling s/finised/finished/
  spi: sc18is602: Convert to use bits_per_word_mask
  spi: Remove duplicate code to set default bits_per_word setting
  spi/pxa2xx: fix compilation warning when !CONFIG_PM_SLEEP
  spi: clps711x: Add MODULE_ALIAS to support module auto-loading
  spi: rspi: Add missing clk_disable() calls in error and cleanup paths
  spi: rspi: Spelling s/transmition/transmission/
  spi: rspi: Add support for specifying CPHA/CPOL
  spi/pxa2xx: initialize DMA channels to -1 to prevent inadvertent match
  spi: rspi: Add more QSPI register documentation
  spi: rspi: Add more RSPI register documentation
  spi: rspi: Remove dependency on DMAE for SHMOBILE
  spi/s3c64xx: Correct indentation
  spi: sh: Use spi_sh_clear_bit() instead of open-coded
  spi: bitbang: Grammar s/make to make/to make/
  spi: sh-hspi: Spelling s/recive/receive/
  spi: core: Improve tx/rx_nbits check comments
  ...

1 files changed, 4 insertions, 4 deletions

diff --git a/Documentation/spi/spi-summary b/Documentation/spi/spi-summary
index f21edb983413..f72e0d1e0da8 100644
--- a/Documentation/spi/spi-summary
+++ b/Documentation/spi/spi-summary
@@ -34,7 +34,7 @@ SPI slave functions are usually not interoperable between vendors
   - It may also be used to stream data in either direction (half duplex),
     or both of them at the same time (full duplex).
 
-  - Some devices may use eight bit words.  Others may different word
+  - Some devices may use eight bit words.  Others may use different word
     lengths, such as streams of 12-bit or 20-bit digital samples.
 
   - Words are usually sent with their most significant bit (MSB) first,
@@ -121,7 +121,7 @@ active.  So the master must set the clock to inactive before selecting
 a slave, and the slave can tell the chosen polarity by sampling the
 clock level when its select line goes active.  That's why many devices
 support for example both modes 0 and 3:  they don't care about polarity,
-and alway clock data in/out on rising clock edges.
+and always clock data in/out on rising clock edges.
 
 
 How do these driver programming interfaces work?
@@ -139,7 +139,7 @@ a command and then reading its response.
 
 There are two types of SPI driver, here called:
 
-  Controller drivers ... controllers may be built in to System-On-Chip
+  Controller drivers ... controllers may be built into System-On-Chip
 	processors, and often support both Master and Slave roles.
 	These drivers touch hardware registers and may use DMA.
 	Or they can be PIO bitbangers, needing just GPIO pins.
@@ -548,7 +548,7 @@ SPI MASTER METHODS
     DEPRECATED METHODS
 
     master->transfer(struct spi_device *spi, struct spi_message *message)
-	This must not sleep. Its responsibility is arrange that the
+	This must not sleep. Its responsibility is to arrange that the
 	transfer happens and its complete() callback is issued. The two
 	will normally happen later, after other transfers complete, and
 	if the controller is idle it will need to be kickstarted. This