Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

Conflicts:
	net/bridge/br_mdb.c

Minor conflict in br_mdb.c, in 'net' we added a memset of the
on-stack 'ip' variable whereas in 'net-next' we assign a new
member 'vid'.

Signed-off-by: David S. Miller <davem@davemloft.net>

26 files changed, 454 insertions, 298 deletions

diff --git a/Documentation/arm/sunxi/README b/Documentation/arm/sunxi/README
index 1fe2d7fd4108..5e38e1582f95 100644
--- a/Documentation/arm/sunxi/README
+++ b/Documentation/arm/sunxi/README
@@ -36,7 +36,7 @@ SunXi family
         + User Manual
           http://dl.linux-sunxi.org/A20/A20%20User%20Manual%202013-03-22.pdf
 
-      - Allwinner A23
+      - Allwinner A23 (sun8i)
         + Datasheet
           http://dl.linux-sunxi.org/A23/A23%20Datasheet%20V1.0%2020130830.pdf
         + User Manual
@@ -55,7 +55,23 @@ SunXi family
         + User Manual
           http://dl.linux-sunxi.org/A31/A3x_release_document/A31s/IC/A31s%20User%20Manual%20%20V1.0%2020130322.pdf
 
+      - Allwinner A33 (sun8i)
+        + Datasheet
+          http://dl.linux-sunxi.org/A33/A33%20Datasheet%20release%201.1.pdf
+        + User Manual
+          http://dl.linux-sunxi.org/A33/A33%20user%20manual%20release%201.1.pdf
+
+      - Allwinner H3 (sun8i)
+        + Datasheet
+          http://dl.linux-sunxi.org/H3/Allwinner_H3_Datasheet_V1.0.pdf
+
     * Quad ARM Cortex-A15, Quad ARM Cortex-A7 based SoCs
       - Allwinner A80
         + Datasheet
 	  http://dl.linux-sunxi.org/A80/A80_Datasheet_Revision_1.0_0404.pdf
+
+    * Octa ARM Cortex-A7 based SoCs
+      - Allwinner A83T
+        + Not Supported
+        + Datasheet
+          http://dl.linux-sunxi.org/A83T/A83T_datasheet_Revision_1.1.pdf
diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt
index 42941fdefb11..67da20539540 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.txt
+++ b/Documentation/devicetree/bindings/arm/sunxi.txt
@@ -9,4 +9,6 @@ using one of the following compatible strings:
   allwinner,sun6i-a31
   allwinner,sun7i-a20
   allwinner,sun8i-a23
+  allwinner,sun8i-a33
+  allwinner,sun8i-h3
   allwinner,sun9i-a80
diff --git a/Documentation/devicetree/bindings/hwlock/hwlock.txt b/Documentation/devicetree/bindings/hwlock/hwlock.txt
new file mode 100644
index 000000000000..085d1f5c916a
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwlock/hwlock.txt
@@ -0,0 +1,59 @@
+Generic hwlock bindings
+=======================
+
+Generic bindings that are common to all the hwlock platform specific driver
+implementations.
+
+Please also look through the individual platform specific hwlock binding
+documentations for identifying any additional properties specific to that
+platform.
+
+hwlock providers:
+=================
+
+Required properties:
+- #hwlock-cells:        Specifies the number of cells needed to represent a
+                        specific lock.
+
+hwlock users:
+=============
+
+Consumers that require specific hwlock(s) should specify them using the
+property "hwlocks", and an optional "hwlock-names" property.
+
+Required properties:
+- hwlocks:              List of phandle to a hwlock provider node and an
+                        associated hwlock args specifier as indicated by
+                        #hwlock-cells. The list can have just a single hwlock
+                        or multiple hwlocks, with each hwlock represented by
+                        a phandle and a corresponding args specifier.
+
+Optional properties:
+- hwlock-names:         List of hwlock name strings defined in the same order
+                        as the hwlocks, with one name per hwlock. Consumers can
+                        use the hwlock-names to match and get a specific hwlock.
+
+
+1. Example of a node using a single specific hwlock:
+
+The following example has a node requesting a hwlock in the bank defined by
+the node hwlock1. hwlock1 is a hwlock provider with an argument specifier
+of length 1.
+
+	node {
+		...
+		hwlocks = <&hwlock1 2>;
+		...
+	};
+
+2. Example of a node using multiple specific hwlocks:
+
+The following example has a node requesting two hwlocks, a hwlock within
+the hwlock device node 'hwlock1' with #hwlock-cells value of 1, and another
+hwlock within the hwlock device node 'hwlock2' with #hwlock-cells value of 2.
+
+	node {
+		...
+		hwlocks = <&hwlock1 2>, <&hwlock2 0 3>;
+		...
+	};
diff --git a/Documentation/devicetree/bindings/hwlock/omap-hwspinlock.txt b/Documentation/devicetree/bindings/hwlock/omap-hwspinlock.txt
new file mode 100644
index 000000000000..2c9804f4f4ac
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwlock/omap-hwspinlock.txt
@@ -0,0 +1,26 @@
+OMAP4+ HwSpinlock Driver
+========================
+
+Required properties:
+- compatible:		Should be "ti,omap4-hwspinlock" for
+			    OMAP44xx, OMAP54xx, AM33xx, AM43xx, DRA7xx SoCs
+- reg:			Contains the hwspinlock module register address space
+			(base address and length)
+- ti,hwmods:		Name of the hwmod associated with the hwspinlock device
+- #hwlock-cells:	Should be 1. The OMAP hwspinlock users will use a
+			0-indexed relative hwlock number as the argument
+			specifier value for requesting a specific hwspinlock
+			within a hwspinlock bank.
+
+Please look at the generic hwlock binding for usage information for consumers,
+"Documentation/devicetree/bindings/hwlock/hwlock.txt"
+
+Example:
+
+/* OMAP4 */
+hwspinlock: spinlock@4a0f6000 {
+	compatible = "ti,omap4-hwspinlock";
+	reg = <0x4a0f6000 0x1000>;
+	ti,hwmods = "spinlock";
+	#hwlock-cells = <1>;
+};
diff --git a/Documentation/devicetree/bindings/hwlock/qcom-hwspinlock.txt b/Documentation/devicetree/bindings/hwlock/qcom-hwspinlock.txt
new file mode 100644
index 000000000000..4563f524556b
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwlock/qcom-hwspinlock.txt
@@ -0,0 +1,39 @@
+Qualcomm Hardware Mutex Block:
+
+The hardware block provides mutexes utilized between different processors on
+the SoC as part of the communication protocol used by these processors.
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be one of:
+		    "qcom,sfpb-mutex",
+		    "qcom,tcsr-mutex"
+
+- syscon:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: one cell containing:
+		    syscon phandle
+		    offset of the hwmutex block within the syscon
+		    stride of the hwmutex registers
+
+- #hwlock-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 1, the specified cell represent the lock id
+		    (hwlock standard property, see hwlock.txt)
+
+Example:
+
+	tcsr_mutex_block: syscon@fd484000 {
+		compatible = "syscon";
+		reg = <0xfd484000 0x2000>;
+	};
+
+	hwlock@fd484000 {
+		compatible = "qcom,tcsr-mutex";
+		syscon = <&tcsr_mutex_block 0 0x80>;
+
+		#hwlock-cells = <1>;
+	};
diff --git a/Documentation/devicetree/bindings/hwlock/sirf,hwspinlock.txt b/Documentation/devicetree/bindings/hwlock/sirf,hwspinlock.txt
new file mode 100644
index 000000000000..9bb1240a68e0
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwlock/sirf,hwspinlock.txt
@@ -0,0 +1,28 @@
+SIRF Hardware spinlock device Binding
+-----------------------------------------------
+
+Required properties :
+- compatible : shall contain only one of the following:
+	"sirf,hwspinlock"
+
+- reg : the register address of hwspinlock
+
+- #hwlock-cells : hwlock users only use the hwlock id to represent a specific
+	hwlock, so the number of cells should be <1> here.
+
+Please look at the generic hwlock binding for usage information for consumers,
+"Documentation/devicetree/bindings/hwlock/hwlock.txt"
+
+Example of hwlock provider:
+	hwlock {
+		compatible = "sirf,hwspinlock";
+		reg = <0x13240000 0x00010000>;
+		#hwlock-cells = <1>;
+	};
+
+Example of hwlock users:
+	node {
+		...
+		hwlocks = <&hwlock 2>;
+		...
+	};
diff --git a/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt
index 938f8e1ba205..0db60470ebb6 100644
--- a/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt
+++ b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt
@@ -8,6 +8,7 @@ of the EMIF IP and memory parts attached to it.
 Required properties:
 - compatible	: Should be of the form "ti,emif-<ip-rev>" where <ip-rev>
   is the IP revision of the specific EMIF instance.
+		  For am437x should be ti,emif-am4372.
 
 - phy-type	: <u32> indicating the DDR phy type. Following are the
   allowed values
diff --git a/Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt b/Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt
new file mode 100644
index 000000000000..3a70073797eb
--- /dev/null
+++ b/Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt
@@ -0,0 +1,52 @@
+TI Wakeup M3 Remoteproc Driver
+==============================
+
+The TI AM33xx and AM43xx family of devices use a small Cortex M3 co-processor
+(commonly referred to as Wakeup M3 or CM3) to help with various low power tasks
+that cannot be controlled from the MPU. This CM3 processor requires a firmware
+binary to accomplish this. The wkup_m3 remoteproc driver handles the loading of
+the firmware and booting of the CM3.
+
+Wkup M3 Device Node:
+====================
+A wkup_m3 device node is used to represent the Wakeup M3 processor instance
+within the SoC. It is added as a child node of the parent interconnect bus
+(l4_wkup) through which it is accessible to the MPU.
+
+Required properties:
+--------------------
+- compatible:		Should be one of,
+				"ti,am3352-wkup-m3" for AM33xx SoCs
+				"ti,am4372-wkup-m3" for AM43xx SoCs
+- reg:			Should contain the address ranges for the two internal
+			memory regions, UMEM and DMEM. The parent node should
+			provide an appropriate ranges property for properly
+			translating these into bus addresses.
+- reg-names:		Contains the corresponding names for the two memory
+			regions. These should be named "umem" & "dmem".
+- ti,hwmods:		Name of the hwmod associated with the wkupm3 device.
+- ti,pm-firmware:	Name of firmware file to be used for loading and
+			booting the wkup_m3 remote processor.
+
+Example:
+--------
+/* AM33xx */
+ocp {
+	 l4_wkup: l4_wkup@44c00000 {
+		compatible = "am335-l4-wkup", "simple-bus";
+		ranges = <0 0x44c00000 0x400000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		wkup_m3: wkup_m3@100000 {
+			compatible = "ti,am3352-wkup-m3";
+			reg = <0x100000 0x4000>,
+			      <0x180000 0x2000>;
+			reg-names = "umem", "dmem";
+			ti,hwmods = "wkup_m3";
+			ti,pm-firmware = "am335x-pm-firmware.elf";
+		};
+	};
+
+	...
+};
diff --git a/Documentation/devicetree/bindings/usb/atmel-usb.txt b/Documentation/devicetree/bindings/usb/atmel-usb.txt
index 1be8d7a26c15..5883b73ea1b5 100644
--- a/Documentation/devicetree/bindings/usb/atmel-usb.txt
+++ b/Documentation/devicetree/bindings/usb/atmel-usb.txt
@@ -79,9 +79,9 @@ Atmel High-Speed USB device controller
 
 Required properties:
  - compatible: Should be one of the following
-	       "at91sam9rl-udc"
-	       "at91sam9g45-udc"
-	       "sama5d3-udc"
+	       "atmel,at91sam9rl-udc"
+	       "atmel,at91sam9g45-udc"
+	       "atmel,sama5d3-udc"
  - reg: Address and length of the register set for the device
  - interrupts: Should contain usba interrupt
  - clocks: Should reference the peripheral and host clocks
diff --git a/Documentation/filesystems/caching/backend-api.txt b/Documentation/filesystems/caching/backend-api.txt
index 277d1e810670..c0bd5677271b 100644
--- a/Documentation/filesystems/caching/backend-api.txt
+++ b/Documentation/filesystems/caching/backend-api.txt
@@ -676,6 +676,29 @@ FS-Cache provides some utilities that a cache backend may make use of:
      as possible.
 
 
+ (*) Indicate that a stale object was found and discarded:
+
+	void fscache_object_retrying_stale(struct fscache_object *object);
+
+     This is called to indicate that the lookup procedure found an object in
+     the cache that the netfs decided was stale.  The object has been
+     discarded from the cache and the lookup will be performed again.
+
+
+ (*) Indicate that the caching backend killed an object:
+
+	void fscache_object_mark_killed(struct fscache_object *object,
+					enum fscache_why_object_killed why);
+
+     This is called to indicate that the cache backend preemptively killed an
+     object.  The why parameter should be set to indicate the reason:
+
+	FSCACHE_OBJECT_IS_STALE - the object was stale and needs discarding.
+	FSCACHE_OBJECT_NO_SPACE - there was insufficient cache space
+	FSCACHE_OBJECT_WAS_RETIRED - the object was retired when relinquished.
+	FSCACHE_OBJECT_WAS_CULLED - the object was culled to make space.
+
+
  (*) Get and release references on a retrieval record:
 
 	void fscache_get_retrieval(struct fscache_retrieval *op);
diff --git a/Documentation/filesystems/caching/fscache.txt b/Documentation/filesystems/caching/fscache.txt
index 770267af5b3e..50f0a5757f48 100644
--- a/Documentation/filesystems/caching/fscache.txt
+++ b/Documentation/filesystems/caching/fscache.txt
@@ -284,8 +284,9 @@ proc files.
 		enq=N	Number of times async ops queued for processing
 		can=N	Number of async ops cancelled
 		rej=N	Number of async ops rejected due to object lookup/create failure
+		ini=N	Number of async ops initialised
 		dfr=N	Number of async ops queued for deferred release
-		rel=N	Number of async ops released
+		rel=N	Number of async ops released (should equal ini=N when idle)
 		gc=N	Number of deferred-release async ops garbage collected
 	CacheOp	alo=N	Number of in-progress alloc_object() cache ops
 		luo=N	Number of in-progress lookup_object() cache ops
@@ -303,6 +304,10 @@ proc files.
 		wrp=N	Number of in-progress write_page() cache ops
 		ucp=N	Number of in-progress uncache_page() cache ops
 		dsp=N	Number of in-progress dissociate_pages() cache ops
+	CacheEv	nsp=N	Number of object lookups/creations rejected due to lack of space
+		stl=N	Number of stale objects deleted
+		rtr=N	Number of objects retired when relinquished
+		cul=N	Number of objects culled
 
 
  (*) /proc/fs/fscache/histogram
diff --git a/Documentation/filesystems/dax.txt b/Documentation/filesystems/dax.txt
index baf41118660d..7af2851d667c 100644
--- a/Documentation/filesystems/dax.txt
+++ b/Documentation/filesystems/dax.txt
@@ -18,8 +18,10 @@ Usage
 -----
 
 If you have a block device which supports DAX, you can make a filesystem
-on it as usual.  When mounting it, use the -o dax option manually
-or add 'dax' to the options in /etc/fstab.
+on it as usual.  The DAX code currently only supports files with a block
+size equal to your kernel's PAGE_SIZE, so you may need to specify a block
+size when creating the filesystem.  When mounting it, use the "-o dax"
+option on the command line or add 'dax' to the options in /etc/fstab.
 
 
 Implementation Tips for Block Driver Writers
diff --git a/Documentation/filesystems/porting b/Documentation/filesystems/porting
index 68f1c9106573..f24d1b833957 100644
--- a/Documentation/filesystems/porting
+++ b/Documentation/filesystems/porting
@@ -500,3 +500,7 @@ in your dentry operations instead.
 	dentry,  it does not get nameidata at all and it gets called only when cookie
 	is non-NULL.  Note that link body isn't available anymore, so if you need it,
 	store it as cookie.
+--
+[mandatory]
+	__fd_install() & fd_install() can now sleep. Callers should not
+	hold a spinlock	or other resources that do not allow a schedule.
diff --git a/Documentation/hwmon/submitting-patches b/Documentation/hwmon/submitting-patches
index 3d1bac399a22..d201828d202f 100644
--- a/Documentation/hwmon/submitting-patches
+++ b/Documentation/hwmon/submitting-patches
@@ -81,6 +81,13 @@ increase the chances of your change being accepted.
 
 * Provide a detect function if and only if a chip can be detected reliably.
 
+* Only the following I2C addresses shall be probed: 0x18-0x1f, 0x28-0x2f,
+  0x48-0x4f, 0x58, 0x5c, 0x73 and 0x77. Probing other addresses is strongly
+  discouraged as it is known to cause trouble with other (non-hwmon) I2C
+  chips. If your chip lives at an address which can't be probed then the
+  device will have to be instantiated explicitly (which is always better
+  anyway.)
+
 * Avoid writing to chip registers in the detect function. If you have to write,
   only do it after you have already gathered enough data to be certain that the
   detection is going to be successful.
diff --git a/Documentation/hwmon/w83792d b/Documentation/hwmon/w83792d
index 53f7b6866fec..f2ffc402ea45 100644
--- a/Documentation/hwmon/w83792d
+++ b/Documentation/hwmon/w83792d
@@ -8,6 +8,7 @@ Supported chips:
     Datasheet: http://www.winbond.com.tw
 
 Author: Shane Huang (Winbond)
+Updated: Roger Lucas
 
 
 Module Parameters
@@ -38,9 +39,16 @@ parameter; this will put it into a more well-behaved state first.
 The driver implements three temperature sensors, seven fan rotation speed
 sensors, nine voltage sensors, and two automatic fan regulation
 strategies called: Smart Fan I (Thermal Cruise mode) and Smart Fan II.
-Automatic fan control mode is possible only for fan1-fan3. Fan4-fan7 can run
-synchronized with selected fan (fan1-fan3). This functionality and manual PWM
-control for fan4-fan7 is not yet implemented.
+
+The driver also implements up to seven fan control outputs: pwm1-7.  Pwm1-7
+can be configured to PWM output or Analogue DC output via their associated
+pwmX_mode. Outputs pwm4 through pwm7 may or may not be present depending on
+how the W83792AD/D was configured by the BIOS.
+
+Automatic fan control mode is possible only for fan1-fan3.
+
+For all pwmX outputs, a value of 0 means minimum fan speed and a value of
+255 means maximum fan speed.
 
 Temperatures are measured in degrees Celsius and measurement resolution is 1
 degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when
@@ -157,14 +165,14 @@ for each fan.
 /sys files
 ----------
 
-pwm[1-3] - this file stores PWM duty cycle or DC value (fan speed) in range:
+pwm[1-7] - this file stores PWM duty cycle or DC value (fan speed) in range:
 	0 (stop) to 255 (full)
 pwm[1-3]_enable - this file controls mode of fan/temperature control:
             * 0 Disabled
             * 1 Manual mode
             * 2 Smart Fan II
             * 3 Thermal Cruise
-pwm[1-3]_mode - Select PWM of DC mode
+pwm[1-7]_mode - Select PWM or DC mode
             * 0 DC
             * 1 PWM
 thermal_cruise[1-3] - Selects the desired temperature for cruise (degC)
diff --git a/Documentation/hwspinlock.txt b/Documentation/hwspinlock.txt
index 62f7d4ea6e26..61c1ee98e59f 100644
--- a/Documentation/hwspinlock.txt
+++ b/Documentation/hwspinlock.txt
@@ -48,6 +48,16 @@ independent, drivers.
      ids for predefined purposes.
      Should be called from a process context (might sleep).
 
+  int of_hwspin_lock_get_id(struct device_node *np, int index);
+   - retrieve the global lock id for an OF phandle-based specific lock.
+     This function provides a means for DT users of a hwspinlock module
+     to get the global lock id of a specific hwspinlock, so that it can
+     be requested using the normal hwspin_lock_request_specific() API.
+     The function returns a lock id number on success, -EPROBE_DEFER if
+     the hwspinlock device is not yet registered with the core, or other
+     error values.
+     Should be called from a process context (might sleep).
+
   int hwspin_lock_free(struct hwspinlock *hwlock);
    - free a previously-assigned hwspinlock; returns 0 on success, or an
      appropriate error code on failure (e.g. -EINVAL if the hwspinlock
diff --git a/Documentation/ioctl/ioctl-number.txt b/Documentation/ioctl/ioctl-number.txt
index 51f4221657bf..611c52267d24 100644
--- a/Documentation/ioctl/ioctl-number.txt
+++ b/Documentation/ioctl/ioctl-number.txt
@@ -321,6 +321,7 @@ Code  Seq#(hex)	Include File		Comments
 0xDB	00-0F	drivers/char/mwave/mwavepub.h
 0xDD	00-3F	ZFCP device driver	see drivers/s390/scsi/
 					<mailto:aherrman@de.ibm.com>
+0xE5	00-3F	linux/fuse.h
 0xEC	00-01	drivers/platform/chrome/cros_ec_dev.h	ChromeOS EC driver
 0xF3	00-3F	drivers/usb/misc/sisusbvga/sisusb.h	sisfb (in development)
 					<mailto:thomas@winischhofer.net>
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index afe7e2bbbc23..1d6f0459cd7b 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -293,6 +293,12 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 	acpi_os_name=	[HW,ACPI] Tell ACPI BIOS the name of the OS
 			Format: To spoof as Windows 98: ="Microsoft Windows"
 
+	acpi_rev_override [ACPI] Override the _REV object to return 5 (instead
+			of 2 which is mandated by ACPI 6) as the supported ACPI
+			specification revision (when using this switch, it may
+			be necessary to carry out a cold reboot _twice_ in a
+			row to make it take effect on the platform firmware).
+
 	acpi_osi=	[HW,ACPI] Modify list of supported OS interface strings
 			acpi_osi="string1"	# add string1
 			acpi_osi="!string2"	# remove string2
diff --git a/Documentation/ntb.txt b/Documentation/ntb.txt
new file mode 100644
index 000000000000..1d9bbabb6c79
--- /dev/null
+++ b/Documentation/ntb.txt
@@ -0,0 +1,127 @@
+# NTB Drivers
+
+NTB (Non-Transparent Bridge) is a type of PCI-Express bridge chip that connects
+the separate memory systems of two computers to the same PCI-Express fabric.
+Existing NTB hardware supports a common feature set, including scratchpad
+registers, doorbell registers, and memory translation windows.  Scratchpad
+registers are read-and-writable registers that are accessible from either side
+of the device, so that peers can exchange a small amount of information at a
+fixed address.  Doorbell registers provide a way for peers to send interrupt
+events.  Memory windows allow translated read and write access to the peer
+memory.
+
+## NTB Core Driver (ntb)
+
+The NTB core driver defines an api wrapping the common feature set, and allows
+clients interested in NTB features to discover NTB the devices supported by
+hardware drivers.  The term "client" is used here to mean an upper layer
+component making use of the NTB api.  The term "driver," or "hardware driver,"
+is used here to mean a driver for a specific vendor and model of NTB hardware.
+
+## NTB Client Drivers
+
+NTB client drivers should register with the NTB core driver.  After
+registering, the client probe and remove functions will be called appropriately
+as ntb hardware, or hardware drivers, are inserted and removed.  The
+registration uses the Linux Device framework, so it should feel familiar to
+anyone who has written a pci driver.
+
+### NTB Transport Client (ntb\_transport) and NTB Netdev (ntb\_netdev)
+
+The primary client for NTB is the Transport client, used in tandem with NTB
+Netdev.  These drivers function together to create a logical link to the peer,
+across the ntb, to exchange packets of network data.  The Transport client
+establishes a logical link to the peer, and creates queue pairs to exchange
+messages and data.  The NTB Netdev then creates an ethernet device using a
+Transport queue pair.  Network data is copied between socket buffers and the
+Transport queue pair buffer.  The Transport client may be used for other things
+besides Netdev, however no other applications have yet been written.
+
+### NTB Ping Pong Test Client (ntb\_pingpong)
+
+The Ping Pong test client serves as a demonstration to exercise the doorbell
+and scratchpad registers of NTB hardware, and as an example simple NTB client.
+Ping Pong enables the link when started, waits for the NTB link to come up, and
+then proceeds to read and write the doorbell scratchpad registers of the NTB.
+The peers interrupt each other using a bit mask of doorbell bits, which is
+shifted by one in each round, to test the behavior of multiple doorbell bits
+and interrupt vectors.  The Ping Pong driver also reads the first local
+scratchpad, and writes the value plus one to the first peer scratchpad, each
+round before writing the peer doorbell register.
+
+Module Parameters:
+
+* unsafe - Some hardware has known issues with scratchpad and doorbell
+	registers.  By default, Ping Pong will not attempt to exercise such
+	hardware.  You may override this behavior at your own risk by setting
+	unsafe=1.
+* delay\_ms - Specify the delay between receiving a doorbell
+	interrupt event and setting the peer doorbell register for the next
+	round.
+* init\_db - Specify the doorbell bits to start new series of rounds.  A new
+	series begins once all the doorbell bits have been shifted out of
+	range.
+* dyndbg - It is suggested to specify dyndbg=+p when loading this module, and
+	then to observe debugging output on the console.
+
+### NTB Tool Test Client (ntb\_tool)
+
+The Tool test client serves for debugging, primarily, ntb hardware and drivers.
+The Tool provides access through debugfs for reading, setting, and clearing the
+NTB doorbell, and reading and writing scratchpads.
+
+The Tool does not currently have any module parameters.
+
+Debugfs Files:
+
+* *debugfs*/ntb\_tool/*hw*/ - A directory in debugfs will be created for each
+	NTB device probed by the tool.  This directory is shortened to *hw*
+	below.
+* *hw*/db - This file is used to read, set, and clear the local doorbell.  Not
+	all operations may be supported by all hardware.  To read the doorbell,
+	read the file.  To set the doorbell, write `s` followed by the bits to
+	set (eg: `echo 's 0x0101' > db`).  To clear the doorbell, write `c`
+	followed by the bits to clear.
+* *hw*/mask - This file is used to read, set, and clear the local doorbell mask.
+	See *db* for details.
+* *hw*/peer\_db - This file is used to read, set, and clear the peer doorbell.
+	See *db* for details.
+* *hw*/peer\_mask - This file is used to read, set, and clear the peer doorbell
+	mask.  See *db* for details.
+* *hw*/spad - This file is used to read and write local scratchpads.  To read
+	the values of all scratchpads, read the file.  To write values, write a
+	series of pairs of scratchpad number and value
+	(eg: `echo '4 0x123 7 0xabc' > spad`
+	# to set scratchpads `4` and `7` to `0x123` and `0xabc`, respectively).
+* *hw*/peer\_spad - This file is used to read and write peer scratchpads.  See
+	*spad* for details.
+
+## NTB Hardware Drivers
+
+NTB hardware drivers should register devices with the NTB core driver.  After
+registering, clients probe and remove functions will be called.
+
+### NTB Intel Hardware Driver (ntb\_hw\_intel)
+
+The Intel hardware driver supports NTB on Xeon and Atom CPUs.
+
+Module Parameters:
+
+* b2b\_mw\_idx - If the peer ntb is to be accessed via a memory window, then use
+	this memory window to access the peer ntb.  A value of zero or positive
+	starts from the first mw idx, and a negative value starts from the last
+	mw idx.  Both sides MUST set the same value here!  The default value is
+	`-1`.
+* b2b\_mw\_share - If the peer ntb is to be accessed via a memory window, and if
+	the memory window is large enough, still allow the client to use the
+	second half of the memory window for address translation to the peer.
+* xeon\_b2b\_usd\_bar2\_addr64 - If using B2B topology on Xeon hardware, use
+	this 64 bit address on the bus between the NTB devices for the window
+	at BAR2, on the upstream side of the link.
+* xeon\_b2b\_usd\_bar4\_addr64 - See *xeon\_b2b\_bar2\_addr64*.
+* xeon\_b2b\_usd\_bar4\_addr32 - See *xeon\_b2b\_bar2\_addr64*.
+* xeon\_b2b\_usd\_bar5\_addr32 - See *xeon\_b2b\_bar2\_addr64*.
+* xeon\_b2b\_dsd\_bar2\_addr64 - See *xeon\_b2b\_bar2\_addr64*.
+* xeon\_b2b\_dsd\_bar4\_addr64 - See *xeon\_b2b\_bar2\_addr64*.
+* xeon\_b2b\_dsd\_bar4\_addr32 - See *xeon\_b2b\_bar2\_addr64*.
+* xeon\_b2b\_dsd\_bar5\_addr32 - See *xeon\_b2b\_bar2\_addr64*.
diff --git a/Documentation/power/swsusp.txt b/Documentation/power/swsusp.txt
index f732a8321e8a..8cc17ca71813 100644
--- a/Documentation/power/swsusp.txt
+++ b/Documentation/power/swsusp.txt
@@ -410,8 +410,17 @@ Documentation/usb/persist.txt.
 
 Q: Can I suspend-to-disk using a swap partition under LVM?
 
-A: No. You can suspend successfully, but you'll not be able to
-resume. uswsusp should be able to work with LVM. See suspend.sf.net.
+A: Yes and No.  You can suspend successfully, but the kernel will not be able
+to resume on its own.  You need an initramfs that can recognize the resume
+situation, activate the logical volume containing the swap volume (but not
+touch any filesystems!), and eventually call
+
+echo -n "$major:$minor" > /sys/power/resume
+
+where $major and $minor are the respective major and minor device numbers of
+the swap volume.
+
+uswsusp works with LVM, too.  See http://suspend.sourceforge.net/
 
 Q: I upgraded the kernel from 2.6.15 to 2.6.16. Both kernels were
 compiled with the similar configuration files. Anyway I found that
diff --git a/Documentation/remoteproc.txt b/Documentation/remoteproc.txt
index e6469fdcf89a..ef0219fa4bb4 100644
--- a/Documentation/remoteproc.txt
+++ b/Documentation/remoteproc.txt
@@ -51,6 +51,12 @@ cost.
         rproc_shutdown() returns, and users can still use it with a subsequent
         rproc_boot(), if needed.
 
+  struct rproc *rproc_get_by_phandle(phandle phandle)
+    - Find an rproc handle using a device tree phandle. Returns the rproc
+      handle on success, and NULL on failure. This function increments
+      the remote processor's refcount, so always use rproc_put() to
+      decrement it back once rproc isn't needed anymore.
+
 3. Typical usage
 
 #include <linux/remoteproc.h>
diff --git a/Documentation/target/tcm_mod_builder.py b/Documentation/target/tcm_mod_builder.py
index 6085e1f19c9d..949de191fcdc 100755
--- a/Documentation/target/tcm_mod_builder.py
+++ b/Documentation/target/tcm_mod_builder.py
@@ -50,15 +50,6 @@ def tcm_mod_build_FC_include(fabric_mod_dir_var, fabric_mod_name):
 	buf = "#define " + fabric_mod_name.upper() + "_VERSION	\"v0.1\"\n"
 	buf += "#define " + fabric_mod_name.upper() + "_NAMELEN	32\n"
 	buf += "\n"
-	buf += "struct " + fabric_mod_name + "_nacl {\n"
-	buf += "	/* Binary World Wide unique Port Name for FC Initiator Nport */\n"
-	buf += "	u64 nport_wwpn;\n"
-	buf += "	/* ASCII formatted WWPN for FC Initiator Nport */\n"
-	buf += "	char nport_name[" + fabric_mod_name.upper() + "_NAMELEN];\n"
-	buf += "	/* Returned by " + fabric_mod_name + "_make_nodeacl() */\n"
-	buf += "	struct se_node_acl se_node_acl;\n"
-	buf += "};\n"
-	buf += "\n"
 	buf += "struct " + fabric_mod_name + "_tpg {\n"
 	buf += "	/* FC lport target portal group tag for TCM */\n"
 	buf += "	u16 lport_tpgt;\n"
@@ -69,8 +60,6 @@ def tcm_mod_build_FC_include(fabric_mod_dir_var, fabric_mod_name):
 	buf += "};\n"
 	buf += "\n"
 	buf += "struct " + fabric_mod_name + "_lport {\n"
-	buf += "	/* SCSI protocol the lport is providing */\n"
-	buf += "	u8 lport_proto_id;\n"
 	buf += "	/* Binary World Wide unique Port Name for FC Target Lport */\n"
 	buf += "	u64 lport_wwpn;\n"
 	buf += "	/* ASCII formatted WWPN for FC Target Lport */\n"
@@ -105,14 +94,6 @@ def tcm_mod_build_SAS_include(fabric_mod_dir_var, fabric_mod_name):
 	buf = "#define " + fabric_mod_name.upper() + "_VERSION  \"v0.1\"\n"
 	buf += "#define " + fabric_mod_name.upper() + "_NAMELEN 32\n"
 	buf += "\n"
-	buf += "struct " + fabric_mod_name + "_nacl {\n"
-	buf += "	/* Binary World Wide unique Port Name for SAS Initiator port */\n"
-	buf += "	u64 iport_wwpn;\n"
-	buf += "	/* ASCII formatted WWPN for Sas Initiator port */\n"
-	buf += "	char iport_name[" + fabric_mod_name.upper() + "_NAMELEN];\n"
-	buf += "	/* Returned by " + fabric_mod_name + "_make_nodeacl() */\n"
-	buf += "	struct se_node_acl se_node_acl;\n"
-	buf += "};\n\n"
 	buf += "struct " + fabric_mod_name + "_tpg {\n"
 	buf += "	/* SAS port target portal group tag for TCM */\n"
 	buf += "	u16 tport_tpgt;\n"
@@ -122,8 +103,6 @@ def tcm_mod_build_SAS_include(fabric_mod_dir_var, fabric_mod_name):
 	buf += "	struct se_portal_group se_tpg;\n"
 	buf += "};\n\n"
 	buf += "struct " + fabric_mod_name + "_tport {\n"
-	buf += "	/* SCSI protocol the tport is providing */\n"
-	buf += "	u8 tport_proto_id;\n"
 	buf += "	/* Binary World Wide unique Port Name for SAS Target port */\n"
 	buf += "	u64 tport_wwpn;\n"
 	buf += "	/* ASCII formatted WWPN for SAS Target port */\n"
@@ -158,12 +137,6 @@ def tcm_mod_build_iSCSI_include(fabric_mod_dir_var, fabric_mod_name):
 	buf = "#define " + fabric_mod_name.upper() + "_VERSION  \"v0.1\"\n"
 	buf += "#define " + fabric_mod_name.upper() + "_NAMELEN 32\n"
 	buf += "\n"
-	buf += "struct " + fabric_mod_name + "_nacl {\n"
-	buf += "	/* ASCII formatted InitiatorName */\n"
-	buf += "	char iport_name[" + fabric_mod_name.upper() + "_NAMELEN];\n"
-	buf += "	/* Returned by " + fabric_mod_name + "_make_nodeacl() */\n"
-	buf += "	struct se_node_acl se_node_acl;\n"
-	buf += "};\n\n"
 	buf += "struct " + fabric_mod_name + "_tpg {\n"
 	buf += "	/* iSCSI target portal group tag for TCM */\n"
 	buf += "	u16 tport_tpgt;\n"
@@ -173,8 +146,6 @@ def tcm_mod_build_iSCSI_include(fabric_mod_dir_var, fabric_mod_name):
 	buf += "	struct se_portal_group se_tpg;\n"
 	buf += "};\n\n"
 	buf += "struct " + fabric_mod_name + "_tport {\n"
-	buf += "	/* SCSI protocol the tport is providing */\n"
-	buf += "	u8 tport_proto_id;\n"
 	buf += "	/* ASCII formatted TargetName for IQN */\n"
 	buf += "	char tport_name[" + fabric_mod_name.upper() + "_NAMELEN];\n"
 	buf += "	/* Returned by " + fabric_mod_name + "_make_tport() */\n"
@@ -232,61 +203,12 @@ def tcm_mod_build_configfs(proto_ident, fabric_mod_dir_var, fabric_mod_name):
 	buf += "#include <target/target_core_base.h>\n"
 	buf += "#include <target/target_core_fabric.h>\n"
 	buf += "#include <target/target_core_fabric_configfs.h>\n"
-	buf += "#include <target/target_core_configfs.h>\n"
 	buf += "#include <target/configfs_macros.h>\n\n"
 	buf += "#include \"" + fabric_mod_name + "_base.h\"\n"
 	buf += "#include \"" + fabric_mod_name + "_fabric.h\"\n\n"
 
 	buf += "static const struct target_core_fabric_ops " + fabric_mod_name + "_ops;\n\n"
 
-	buf += "static struct se_node_acl *" + fabric_mod_name + "_make_nodeacl(\n"
-	buf += "	struct se_portal_group *se_tpg,\n"
-	buf += "	struct config_group *group,\n"
-	buf += "	const char *name)\n"
-	buf += "{\n"
-	buf += "	struct se_node_acl *se_nacl, *se_nacl_new;\n"
-	buf += "	struct " + fabric_mod_name + "_nacl *nacl;\n"
-
-	if proto_ident == "FC" or proto_ident == "SAS":
-		buf += "	u64 wwpn = 0;\n"
-
-	buf += "	u32 nexus_depth;\n\n"
-	buf += "	/* " + fabric_mod_name + "_parse_wwn(name, &wwpn, 1) < 0)\n"
-	buf += "		return ERR_PTR(-EINVAL); */\n"
-	buf += "	se_nacl_new = " + fabric_mod_name + "_alloc_fabric_acl(se_tpg);\n"
-	buf += "	if (!se_nacl_new)\n"
-	buf += "		return ERR_PTR(-ENOMEM);\n"
-	buf += "//#warning FIXME: Hardcoded nexus depth in " + fabric_mod_name + "_make_nodeacl()\n"
-	buf += "	nexus_depth = 1;\n"
-	buf += "	/*\n"
-	buf += "	 * se_nacl_new may be released by core_tpg_add_initiator_node_acl()\n"
-	buf += "	 * when converting a NodeACL from demo mode -> explict\n"
-	buf += "	 */\n"
-	buf += "	se_nacl = core_tpg_add_initiator_node_acl(se_tpg, se_nacl_new,\n"
-	buf += "				name, nexus_depth);\n"
-	buf += "	if (IS_ERR(se_nacl)) {\n"
-	buf += "		" + fabric_mod_name + "_release_fabric_acl(se_tpg, se_nacl_new);\n"
-	buf += "		return se_nacl;\n"
-	buf += "	}\n"
-	buf += "	/*\n"
-	buf += "	 * Locate our struct " + fabric_mod_name + "_nacl and set the FC Nport WWPN\n"
-	buf += "	 */\n"
-	buf += "	nacl = container_of(se_nacl, struct " + fabric_mod_name + "_nacl, se_node_acl);\n"
-
-	if proto_ident == "FC" or proto_ident == "SAS":
-		buf += "	nacl->" + fabric_mod_init_port + "_wwpn = wwpn;\n"
-
-	buf += "	/* " + fabric_mod_name + "_format_wwn(&nacl->" + fabric_mod_init_port + "_name[0], " + fabric_mod_name.upper() + "_NAMELEN, wwpn); */\n\n"
-	buf += "	return se_nacl;\n"
-	buf += "}\n\n"
-	buf += "static void " + fabric_mod_name + "_drop_nodeacl(struct se_node_acl *se_acl)\n"
-	buf += "{\n"
-	buf += "	struct " + fabric_mod_name + "_nacl *nacl = container_of(se_acl,\n"
-	buf += "				struct " + fabric_mod_name + "_nacl, se_node_acl);\n"
-	buf += "	core_tpg_del_initiator_node_acl(se_acl->se_tpg, se_acl, 1);\n"
-	buf += "	kfree(nacl);\n"
-	buf += "}\n\n"
-
 	buf += "static struct se_portal_group *" + fabric_mod_name + "_make_tpg(\n"
 	buf += "	struct se_wwn *wwn,\n"
 	buf += "	struct config_group *group,\n"
@@ -309,8 +231,7 @@ def tcm_mod_build_configfs(proto_ident, fabric_mod_dir_var, fabric_mod_name):
 	buf += "	tpg->" + fabric_mod_port + " = " + fabric_mod_port + ";\n"
 	buf += "	tpg->" + fabric_mod_port + "_tpgt = tpgt;\n\n"
 	buf += "	ret = core_tpg_register(&" + fabric_mod_name + "_ops, wwn,\n"
-	buf += "				&tpg->se_tpg, tpg,\n"
-	buf += "				TRANSPORT_TPG_TYPE_NORMAL);\n"
+	buf += "				&tpg->se_tpg, SCSI_PROTOCOL_SAS);\n"
 	buf += "	if (ret < 0) {\n"
 	buf += "		kfree(tpg);\n"
 	buf += "		return NULL;\n"
@@ -372,21 +293,13 @@ def tcm_mod_build_configfs(proto_ident, fabric_mod_dir_var, fabric_mod_name):
 	buf += "static const struct target_core_fabric_ops " + fabric_mod_name + "_ops = {\n"
 	buf += "	.module				= THIS_MODULE,\n"
 	buf += "	.name				= " + fabric_mod_name + ",\n"
-	buf += "	.get_fabric_proto_ident		= " + fabric_mod_name + "_get_fabric_proto_ident,\n"
 	buf += "	.get_fabric_name		= " + fabric_mod_name + "_get_fabric_name,\n"
-	buf += "	.get_fabric_proto_ident		= " + fabric_mod_name + "_get_fabric_proto_ident,\n"
 	buf += "	.tpg_get_wwn			= " + fabric_mod_name + "_get_fabric_wwn,\n"
 	buf += "	.tpg_get_tag			= " + fabric_mod_name + "_get_tag,\n"
-	buf += "	.tpg_get_default_depth		= " + fabric_mod_name + "_get_default_depth,\n"
-	buf += "	.tpg_get_pr_transport_id	= " + fabric_mod_name + "_get_pr_transport_id,\n"
-	buf += "	.tpg_get_pr_transport_id_len	= " + fabric_mod_name + "_get_pr_transport_id_len,\n"
-	buf += "	.tpg_parse_pr_out_transport_id	= " + fabric_mod_name + "_parse_pr_out_transport_id,\n"
 	buf += "	.tpg_check_demo_mode		= " + fabric_mod_name + "_check_false,\n"
 	buf += "	.tpg_check_demo_mode_cache	= " + fabric_mod_name + "_check_true,\n"
 	buf += "	.tpg_check_demo_mode_write_protect = " + fabric_mod_name + "_check_true,\n"
 	buf += "	.tpg_check_prod_mode_write_protect = " + fabric_mod_name + "_check_false,\n"
-	buf += "	.tpg_alloc_fabric_acl		= " + fabric_mod_name + "_alloc_fabric_acl,\n"
-	buf += "	.tpg_release_fabric_acl		= " + fabric_mod_name + "_release_fabric_acl,\n"
 	buf += "	.tpg_get_inst_index		= " + fabric_mod_name + "_tpg_get_inst_index,\n"
 	buf += "	.release_cmd			= " + fabric_mod_name + "_release_cmd,\n"
 	buf += "	.shutdown_session		= " + fabric_mod_name + "_shutdown_session,\n"
@@ -396,7 +309,6 @@ def tcm_mod_build_configfs(proto_ident, fabric_mod_dir_var, fabric_mod_name):
 	buf += "	.write_pending			= " + fabric_mod_name + "_write_pending,\n"
 	buf += "	.write_pending_status		= " + fabric_mod_name + "_write_pending_status,\n"
 	buf += "	.set_default_node_attributes	= " + fabric_mod_name + "_set_default_node_attrs,\n"
-	buf += "	.get_task_tag			= " + fabric_mod_name + "_get_task_tag,\n"
 	buf += "	.get_cmd_state			= " + fabric_mod_name + "_get_cmd_state,\n"
 	buf += "	.queue_data_in			= " + fabric_mod_name + "_queue_data_in,\n"
 	buf += "	.queue_status			= " + fabric_mod_name + "_queue_status,\n"
@@ -409,12 +321,6 @@ def tcm_mod_build_configfs(proto_ident, fabric_mod_dir_var, fabric_mod_name):
 	buf += "	.fabric_drop_wwn		= " + fabric_mod_name + "_drop_" + fabric_mod_port + ",\n"
 	buf += "	.fabric_make_tpg		= " + fabric_mod_name + "_make_tpg,\n"
 	buf += "	.fabric_drop_tpg		= " + fabric_mod_name + "_drop_tpg,\n"
-	buf += "	.fabric_post_link		= NULL,\n"
-	buf += "	.fabric_pre_unlink		= NULL,\n"
-	buf += "	.fabric_make_np			= NULL,\n"
-	buf += "	.fabric_drop_np			= NULL,\n"
-	buf += "	.fabric_make_nodeacl		= " + fabric_mod_name + "_make_nodeacl,\n"
-	buf += "	.fabric_drop_nodeacl		= " + fabric_mod_name + "_drop_nodeacl,\n"
 	buf += "\n"
 	buf += "	.tfc_wwn_attrs			= " + fabric_mod_name + "_wwn_attrs;\n"
 	buf += "};\n\n"
@@ -507,7 +413,6 @@ def tcm_mod_dump_fabric_ops(proto_ident, fabric_mod_dir_var, fabric_mod_name):
 	buf += "#include <scsi/scsi_proto.h>\n"
 	buf += "#include <target/target_core_base.h>\n"
 	buf += "#include <target/target_core_fabric.h>\n"
-	buf += "#include <target/target_core_configfs.h>\n\n"
 	buf += "#include \"" + fabric_mod_name + "_base.h\"\n"
 	buf += "#include \"" + fabric_mod_name + "_fabric.h\"\n\n"
 
@@ -539,35 +444,6 @@ def tcm_mod_dump_fabric_ops(proto_ident, fabric_mod_dir_var, fabric_mod_name):
 			bufi += "char *" + fabric_mod_name + "_get_fabric_name(void);\n"
 			continue
 
-		if re.search('get_fabric_proto_ident', fo):
-			buf += "u8 " + fabric_mod_name + "_get_fabric_proto_ident(struct se_portal_group *se_tpg)\n"
-			buf += "{\n"
-			buf += "	struct " + fabric_mod_name + "_tpg *tpg = container_of(se_tpg,\n"
-			buf += "				struct " + fabric_mod_name + "_tpg, se_tpg);\n"
-			buf += "	struct " + fabric_mod_name + "_" + fabric_mod_port + " *" + fabric_mod_port + " = tpg->" + fabric_mod_port + ";\n"
-			buf += "	u8 proto_id;\n\n"
-			buf += "	switch (" + fabric_mod_port + "->" + fabric_mod_port + "_proto_id) {\n"
-			if proto_ident == "FC":
-				buf += "	case SCSI_PROTOCOL_FCP:\n"
-				buf += "	default:\n"
-				buf += "		proto_id = fc_get_fabric_proto_ident(se_tpg);\n"
-				buf += "		break;\n"
-			elif proto_ident == "SAS":
-				buf += "	case SCSI_PROTOCOL_SAS:\n"
-				buf += "	default:\n"
-				buf += "		proto_id = sas_get_fabric_proto_ident(se_tpg);\n"
-				buf += "		break;\n"
-			elif proto_ident == "iSCSI":
-				buf += "	case SCSI_PROTOCOL_ISCSI:\n"
-				buf += "	default:\n"
-				buf += "		proto_id = iscsi_get_fabric_proto_ident(se_tpg);\n"
-				buf += "		break;\n"
-
-			buf += "	}\n\n"
-			buf += "	return proto_id;\n"
-			buf += "}\n\n"
-			bufi += "u8 " + fabric_mod_name + "_get_fabric_proto_ident(struct se_portal_group *);\n"
-
 		if re.search('get_wwn', fo):
 			buf += "char *" + fabric_mod_name + "_get_fabric_wwn(struct se_portal_group *se_tpg)\n"
 			buf += "{\n"
@@ -587,150 +463,6 @@ def tcm_mod_dump_fabric_ops(proto_ident, fabric_mod_dir_var, fabric_mod_name):
 			buf += "}\n\n"
 			bufi += "u16 " + fabric_mod_name + "_get_tag(struct se_portal_group *);\n"
 
-		if re.search('get_default_depth', fo):
-			buf += "u32 " + fabric_mod_name + "_get_default_depth(struct se_portal_group *se_tpg)\n"
-			buf += "{\n"
-			buf += "	return 1;\n"
-			buf += "}\n\n"
-			bufi += "u32 " + fabric_mod_name + "_get_default_depth(struct se_portal_group *);\n"
-
-		if re.search('get_pr_transport_id\)\(', fo):
-			buf += "u32 " + fabric_mod_name + "_get_pr_transport_id(\n"
-			buf += "	struct se_portal_group *se_tpg,\n"
-			buf += "	struct se_node_acl *se_nacl,\n"
-			buf += "	struct t10_pr_registration *pr_reg,\n"
-			buf += "	int *format_code,\n"
-			buf += "	unsigned char *buf)\n"
-			buf += "{\n"
-			buf += "	struct " + fabric_mod_name + "_tpg *tpg = container_of(se_tpg,\n"
-			buf += "				struct " + fabric_mod_name + "_tpg, se_tpg);\n"
-			buf += "	struct " + fabric_mod_name + "_" + fabric_mod_port + " *" + fabric_mod_port + " = tpg->" + fabric_mod_port + ";\n"
-			buf += "	int ret = 0;\n\n"
-			buf += "	switch (" + fabric_mod_port + "->" + fabric_mod_port + "_proto_id) {\n"
-			if proto_ident == "FC":
-				buf += "	case SCSI_PROTOCOL_FCP:\n"
-				buf += "	default:\n"
-				buf += "		ret = fc_get_pr_transport_id(se_tpg, se_nacl, pr_reg,\n"
-				buf += "					format_code, buf);\n"
-				buf += "		break;\n"
-			elif proto_ident == "SAS":
-				buf += "	case SCSI_PROTOCOL_SAS:\n"
-				buf += "	default:\n"
-				buf += "		ret = sas_get_pr_transport_id(se_tpg, se_nacl, pr_reg,\n"
-				buf += "					format_code, buf);\n"
-				buf += "		break;\n"
-			elif proto_ident == "iSCSI":
-				buf += "	case SCSI_PROTOCOL_ISCSI:\n"
-				buf += "	default:\n"
-				buf += "		ret = iscsi_get_pr_transport_id(se_tpg, se_nacl, pr_reg,\n"
-				buf += "					format_code, buf);\n"
-				buf += "		break;\n"
-
-			buf += "	}\n\n"
-			buf += "	return ret;\n"
-			buf += "}\n\n"
-			bufi += "u32 " + fabric_mod_name + "_get_pr_transport_id(struct se_portal_group *,\n"
-			bufi += "			struct se_node_acl *, struct t10_pr_registration *,\n"
-			bufi += "			int *, unsigned char *);\n"
-
-		if re.search('get_pr_transport_id_len\)\(', fo):
-			buf += "u32 " + fabric_mod_name + "_get_pr_transport_id_len(\n"
-			buf += "	struct se_portal_group *se_tpg,\n"
-			buf += "	struct se_node_acl *se_nacl,\n"
-			buf += "	struct t10_pr_registration *pr_reg,\n"
-			buf += "	int *format_code)\n"
-			buf += "{\n"
-			buf += "	struct " + fabric_mod_name + "_tpg *tpg = container_of(se_tpg,\n"
-			buf += "				struct " + fabric_mod_name + "_tpg, se_tpg);\n"
-			buf += "	struct " + fabric_mod_name + "_" + fabric_mod_port + " *" + fabric_mod_port + " = tpg->" + fabric_mod_port + ";\n"
-			buf += "	int ret = 0;\n\n"
-			buf += "	switch (" + fabric_mod_port + "->" + fabric_mod_port + "_proto_id) {\n"
-			if proto_ident == "FC":
-				buf += "	case SCSI_PROTOCOL_FCP:\n"
-				buf += "	default:\n"
-				buf += "		ret = fc_get_pr_transport_id_len(se_tpg, se_nacl, pr_reg,\n"
-				buf += "					format_code);\n"
-				buf += "		break;\n"
-			elif proto_ident == "SAS":
-				buf += "	case SCSI_PROTOCOL_SAS:\n"
-				buf += "	default:\n"
-				buf += "		ret = sas_get_pr_transport_id_len(se_tpg, se_nacl, pr_reg,\n"
-				buf += "					format_code);\n"
-				buf += "		break;\n"
-			elif proto_ident == "iSCSI":
-				buf += "	case SCSI_PROTOCOL_ISCSI:\n"
-				buf += "	default:\n"
-				buf += "		ret = iscsi_get_pr_transport_id_len(se_tpg, se_nacl, pr_reg,\n"
-				buf += "					format_code);\n"
-				buf += "		break;\n"
-
-
-			buf += "	}\n\n"
-			buf += "	return ret;\n"
-			buf += "}\n\n"
-			bufi += "u32 " + fabric_mod_name + "_get_pr_transport_id_len(struct se_portal_group *,\n"
-			bufi += "			struct se_node_acl *, struct t10_pr_registration *,\n"
-			bufi += "			int *);\n"
-
-		if re.search('parse_pr_out_transport_id\)\(', fo):
-			buf += "char *" + fabric_mod_name + "_parse_pr_out_transport_id(\n"
-			buf += "	struct se_portal_group *se_tpg,\n"
-			buf += "	const char *buf,\n"
-			buf += "	u32 *out_tid_len,\n"
-			buf += "	char **port_nexus_ptr)\n"
-			buf += "{\n"
-			buf += "	struct " + fabric_mod_name + "_tpg *tpg = container_of(se_tpg,\n"
-			buf += "				struct " + fabric_mod_name + "_tpg, se_tpg);\n"
-			buf += "	struct " + fabric_mod_name + "_" + fabric_mod_port + " *" + fabric_mod_port + " = tpg->" + fabric_mod_port + ";\n"
-			buf += "	char *tid = NULL;\n\n"
-			buf += "	switch (" + fabric_mod_port + "->" + fabric_mod_port + "_proto_id) {\n"
-			if proto_ident == "FC":
-				buf += "	case SCSI_PROTOCOL_FCP:\n"
-				buf += "	default:\n"
-				buf += "		tid = fc_parse_pr_out_transport_id(se_tpg, buf, out_tid_len,\n"
-				buf += "					port_nexus_ptr);\n"
-			elif proto_ident == "SAS":
-				buf += "	case SCSI_PROTOCOL_SAS:\n"
-				buf += "	default:\n"
-				buf += "		tid = sas_parse_pr_out_transport_id(se_tpg, buf, out_tid_len,\n"
-				buf += "					port_nexus_ptr);\n"
-			elif proto_ident == "iSCSI":
-				buf += "	case SCSI_PROTOCOL_ISCSI:\n"
-				buf += "	default:\n"
-				buf += "		tid = iscsi_parse_pr_out_transport_id(se_tpg, buf, out_tid_len,\n"
-				buf += "					port_nexus_ptr);\n"
-
-			buf += "	}\n\n"
-			buf += "	return tid;\n"
-			buf += "}\n\n"
-			bufi += "char *" + fabric_mod_name + "_parse_pr_out_transport_id(struct se_portal_group *,\n"
-			bufi +=	"			const char *, u32 *, char **);\n"
-
-		if re.search('alloc_fabric_acl\)\(', fo):
-			buf += "struct se_node_acl *" + fabric_mod_name + "_alloc_fabric_acl(struct se_portal_group *se_tpg)\n"
-			buf += "{\n"
-			buf += "	struct " + fabric_mod_name + "_nacl *nacl;\n\n"
-			buf += "	nacl = kzalloc(sizeof(struct " + fabric_mod_name + "_nacl), GFP_KERNEL);\n"
-			buf += "	if (!nacl) {\n"
-			buf += "		printk(KERN_ERR \"Unable to allocate struct " + fabric_mod_name + "_nacl\\n\");\n"
-			buf += "		return NULL;\n"
-			buf += "	}\n\n"
-			buf += "	return &nacl->se_node_acl;\n"
-			buf += "}\n\n"
-			bufi += "struct se_node_acl *" + fabric_mod_name + "_alloc_fabric_acl(struct se_portal_group *);\n"
-
-		if re.search('release_fabric_acl\)\(', fo):
-			buf += "void " + fabric_mod_name + "_release_fabric_acl(\n"
-			buf += "	struct se_portal_group *se_tpg,\n"
-			buf += "	struct se_node_acl *se_nacl)\n"
-			buf += "{\n"
-			buf += "	struct " + fabric_mod_name + "_nacl *nacl = container_of(se_nacl,\n"
-			buf += "			struct " + fabric_mod_name + "_nacl, se_node_acl);\n"
-			buf += "	kfree(nacl);\n"
-			buf += "}\n\n"
-			bufi += "void " + fabric_mod_name + "_release_fabric_acl(struct se_portal_group *,\n"
-			bufi +=	"			struct se_node_acl *);\n"
-
 		if re.search('tpg_get_inst_index\)\(', fo):
 			buf += "u32 " + fabric_mod_name + "_tpg_get_inst_index(struct se_portal_group *se_tpg)\n"
 			buf += "{\n"
@@ -787,13 +519,6 @@ def tcm_mod_dump_fabric_ops(proto_ident, fabric_mod_dir_var, fabric_mod_name):
 			buf += "}\n\n"
 			bufi += "void " + fabric_mod_name + "_set_default_node_attrs(struct se_node_acl *);\n"
 
-		if re.search('get_task_tag\)\(', fo):
-			buf += "u32 " + fabric_mod_name + "_get_task_tag(struct se_cmd *se_cmd)\n"
-			buf += "{\n"
-			buf += "	return 0;\n"
-			buf += "}\n\n"
-			bufi += "u32 " + fabric_mod_name + "_get_task_tag(struct se_cmd *);\n"
-
 		if re.search('get_cmd_state\)\(', fo):
 			buf += "int " + fabric_mod_name + "_get_cmd_state(struct se_cmd *se_cmd)\n"
 			buf += "{\n"
diff --git a/Documentation/target/tcm_mod_builder.txt b/Documentation/target/tcm_mod_builder.txt
index 84533d8e747f..ae22f7005540 100644
--- a/Documentation/target/tcm_mod_builder.txt
+++ b/Documentation/target/tcm_mod_builder.txt
@@ -13,8 +13,8 @@ fabric skeleton, by simply using:
 This script will create a new drivers/target/$TCM_NEW_MOD/, and will do the following
 
 	*) Generate new API callers for drivers/target/target_core_fabric_configs.c logic
-	   ->make_nodeacl(), ->drop_nodeacl(), ->make_tpg(), ->drop_tpg()
-	   ->make_wwn(), ->drop_wwn().  These are created into $TCM_NEW_MOD/$TCM_NEW_MOD_configfs.c
+	   ->make_tpg(), ->drop_tpg(), ->make_wwn(), ->drop_wwn().  These are created
+	   into $TCM_NEW_MOD/$TCM_NEW_MOD_configfs.c
 	*) Generate basic infrastructure for loading/unloading LKMs and TCM/ConfigFS fabric module
 	   using a skeleton struct target_core_fabric_ops API template.
 	*) Based on user defined T10 Proto_Ident for the new fabric module being built,
diff --git a/Documentation/target/tcmu-design.txt b/Documentation/target/tcmu-design.txt
index 263b907517ac..bef81e42788f 100644
--- a/Documentation/target/tcmu-design.txt
+++ b/Documentation/target/tcmu-design.txt
@@ -152,7 +152,7 @@ overall shared memory region, not the entry. The data in/out buffers
 are accessible via tht req.iov[] array. iov_cnt contains the number of
 entries in iov[] needed to describe either the Data-In or Data-Out
 buffers. For bidirectional commands, iov_cnt specifies how many iovec
-entries cover the Data-Out area, and iov_bidi_count specifies how many
+entries cover the Data-Out area, and iov_bidi_cnt specifies how many
 iovec entries immediately after that in iov[] cover the Data-In
 area. Just like other fields, iov.iov_base is an offset from the start
 of the region.
diff --git a/Documentation/x86/boot.txt b/Documentation/x86/boot.txt
index 7c1f9fad6674..9da6f3512249 100644
--- a/Documentation/x86/boot.txt
+++ b/Documentation/x86/boot.txt
@@ -406,7 +406,7 @@ Protocol:	2.00+
 	- If 0, the protected-mode code is loaded at 0x10000.
 	- If 1, the protected-mode code is loaded at 0x100000.
 
-  Bit 1 (kernel internal): ALSR_FLAG
+  Bit 1 (kernel internal): KASLR_FLAG
 	- Used internally by the compressed kernel to communicate
 	  KASLR status to kernel proper.
 	  If 1, KASLR enabled.
diff --git a/Documentation/x86/entry_64.txt b/Documentation/x86/entry_64.txt
index 33884d156125..c1df8eba9dfd 100644
--- a/Documentation/x86/entry_64.txt
+++ b/Documentation/x86/entry_64.txt
@@ -1,14 +1,14 @@
 This file documents some of the kernel entries in
-arch/x86/kernel/entry_64.S.  A lot of this explanation is adapted from
+arch/x86/entry/entry_64.S.  A lot of this explanation is adapted from
 an email from Ingo Molnar:
 
 http://lkml.kernel.org/r/<20110529191055.GC9835%40elte.hu>
 
 The x86 architecture has quite a few different ways to jump into
 kernel code.  Most of these entry points are registered in
-arch/x86/kernel/traps.c and implemented in arch/x86/kernel/entry_64.S
-for 64-bit, arch/x86/kernel/entry_32.S for 32-bit and finally
-arch/x86/ia32/ia32entry.S which implements the 32-bit compatibility
+arch/x86/kernel/traps.c and implemented in arch/x86/entry/entry_64.S
+for 64-bit, arch/x86/entry/entry_32.S for 32-bit and finally
+arch/x86/entry/entry_64_compat.S which implements the 32-bit compatibility
 syscall entry points and thus provides for 32-bit processes the
 ability to execute syscalls when running on 64-bit kernels.