Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

Conflicts:
	drivers/net/ethernet/mediatek/mtk_eth_soc.c
	drivers/net/ethernet/qlogic/qed/qed_dcbx.c
	drivers/net/phy/Kconfig

All conflicts were cases of overlapping commits.

Signed-off-by: David S. Miller <davem@davemloft.net>

9 files changed, 31 insertions, 33 deletions

diff --git a/Documentation/ABI/stable/sysfs-devices b/Documentation/ABI/stable/sysfs-devices
index 43f78b88da28..df449d79b563 100644
--- a/Documentation/ABI/stable/sysfs-devices
+++ b/Documentation/ABI/stable/sysfs-devices
@@ -1,7 +1,7 @@
 # Note: This documents additional properties of any device beyond what
 # is documented in Documentation/sysfs-rules.txt
 
-What:		/sys/devices/*/of_path
+What:		/sys/devices/*/of_node
 Date:		February 2015
 Contact:	Device Tree mailing list <devicetree@vger.kernel.org>
 Description:
diff --git a/Documentation/PCI/pci.txt b/Documentation/PCI/pci.txt
index 123881f62219..77f49dc5be23 100644
--- a/Documentation/PCI/pci.txt
+++ b/Documentation/PCI/pci.txt
@@ -124,7 +124,6 @@ initialization with a pointer to a structure describing the driver
 
 The ID table is an array of struct pci_device_id entries ending with an
 all-zero entry.  Definitions with static const are generally preferred.
-Use of the deprecated macro DEFINE_PCI_DEVICE_TABLE should be avoided.
 
 Each entry consists of:
 
diff --git a/Documentation/arm/CCN.txt b/Documentation/arm/CCN.txt
index ffca443a19b4..15cdb7bc57c3 100644
--- a/Documentation/arm/CCN.txt
+++ b/Documentation/arm/CCN.txt
@@ -18,13 +18,17 @@ and config2 fields of the perf_event_attr structure. The "events"
 directory provides configuration templates for all documented
 events, that can be used with perf tool. For example "xp_valid_flit"
 is an equivalent of "type=0x8,event=0x4". Other parameters must be
-explicitly specified. For events originating from device, "node"
-defines its index. All crosspoint events require "xp" (index),
-"port" (device port number) and "vc" (virtual channel ID) and
-"dir" (direction). Watchpoints (special "event" value 0xfe) also
-require comparator values ("cmp_l" and "cmp_h") and "mask", being
-index of the comparator mask.
+explicitly specified.
 
+For events originating from device, "node" defines its index.
+
+Crosspoint PMU events require "xp" (index), "bus" (bus number)
+and "vc" (virtual channel ID).
+
+Crosspoint watchpoint-based events (special "event" value 0xfe)
+require "xp" and "vc" as as above plus "port" (device port index),
+"dir" (transmit/receive direction), comparator values ("cmp_l"
+and "cmp_h") and "mask", being index of the comparator mask.
 Masks are defined separately from the event description
 (due to limited number of the config values) in the "cmp_mask"
 directory, with first 8 configurable by user and additional
diff --git a/Documentation/cpu-freq/cpufreq-stats.txt b/Documentation/cpu-freq/cpufreq-stats.txt
index fc647492e940..8d9773f23550 100644
--- a/Documentation/cpu-freq/cpufreq-stats.txt
+++ b/Documentation/cpu-freq/cpufreq-stats.txt
@@ -103,7 +103,7 @@ Config Main Menu
 	Power management options (ACPI, APM)  --->
 		CPU Frequency scaling  --->
 			[*] CPU Frequency scaling
-			<*>   CPU frequency translation statistics 
+			[*]   CPU frequency translation statistics
 			[*]     CPU frequency translation statistics details
 
 
diff --git a/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt b/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt
index bf99e2f24788..205593f56fe7 100644
--- a/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt
+++ b/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt
@@ -16,6 +16,11 @@ Required properties:
 - vref-supply: The regulator supply ADC reference voltage.
 - #io-channel-cells: Should be 1, see ../iio-bindings.txt
 
+Optional properties:
+- resets: Must contain an entry for each entry in reset-names if need support
+	  this option. See ../reset/reset.txt for details.
+- reset-names: Must include the name "saradc-apb".
+
 Example:
 	saradc: saradc@2006c000 {
 		compatible = "rockchip,saradc";
@@ -23,6 +28,8 @@ Example:
 		interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>;
 		clock-names = "saradc", "apb_pclk";
+		resets = <&cru SRST_SARADC>;
+		reset-names = "saradc-apb";
 		#io-channel-cells = <1>;
 		vref-supply = <&vcc18>;
 	};
diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt
index f5561ac7e17e..936ab5b87324 100644
--- a/Documentation/devicetree/bindings/serial/8250.txt
+++ b/Documentation/devicetree/bindings/serial/8250.txt
@@ -42,9 +42,6 @@ Optional properties:
 - auto-flow-control: one way to enable automatic flow control support. The
   driver is allowed to detect support for the capability even without this
   property.
-- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD
-  line respectively. It will use specified GPIO instead of the peripheral
-  function pin for the UART feature. If unsure, don't specify this property.
 
 Note:
 * fsl,ns16550:
@@ -66,19 +63,3 @@ Example:
 		interrupts = <10>;
 		reg-shift = <2>;
 	};
-
-Example for OMAP UART using GPIO-based modem control signals:
-
-	uart4: serial@49042000 {
-		compatible = "ti,omap3-uart";
-		reg = <0x49042000 0x400>;
-		interrupts = <80>;
-		ti,hwmods = "uart4";
-		clock-frequency = <48000000>;
-		cts-gpios = <&gpio3 5 GPIO_ACTIVE_LOW>;
-		rts-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
-		dtr-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
-		dsr-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
-		dcd-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
-		rng-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
-	};
diff --git a/Documentation/filesystems/overlayfs.txt b/Documentation/filesystems/overlayfs.txt
index d6259c786316..bcbf9710e4af 100644
--- a/Documentation/filesystems/overlayfs.txt
+++ b/Documentation/filesystems/overlayfs.txt
@@ -183,12 +183,10 @@ The copy_up operation essentially creates a new, identical file and
 moves it over to the old name.  The new file may be on a different
 filesystem, so both st_dev and st_ino of the file may change.
 
-Any open files referring to this inode will access the old data and
-metadata.  Similarly any file locks obtained before copy_up will not
-apply to the copied up file.
+Any open files referring to this inode will access the old data.
 
-On a file opened with O_RDONLY fchmod(2), fchown(2), futimesat(2) and
-fsetxattr(2) will fail with EROFS.
+Any file locks (and leases) obtained before copy_up will not apply
+to the copied up file.
 
 If a file with multiple hard links is copied up, then this will
 "break" the link.  Changes will not be propagated to other names
diff --git a/Documentation/i2c/slave-interface b/Documentation/i2c/slave-interface
index 80807adb8ded..7e2a228f21bc 100644
--- a/Documentation/i2c/slave-interface
+++ b/Documentation/i2c/slave-interface
@@ -145,6 +145,11 @@ If you want to add slave support to the bus driver:
 
 * Catch the slave interrupts and send appropriate i2c_slave_events to the backend.
 
+Note that most hardware supports being master _and_ slave on the same bus. So,
+if you extend a bus driver, please make sure that the driver supports that as
+well. In almost all cases, slave support does not need to disable the master
+functionality.
+
 Check the i2c-rcar driver as an example.
 
 
diff --git a/Documentation/rapidio/mport_cdev.txt b/Documentation/rapidio/mport_cdev.txt
index 6e491a662461..a53f786ee2e9 100644
--- a/Documentation/rapidio/mport_cdev.txt
+++ b/Documentation/rapidio/mport_cdev.txt
@@ -80,6 +80,10 @@ functionality of their platform when planning to use this driver:
 
 III. Module parameters
 
+- 'dma_timeout' - DMA transfer completion timeout (in msec, default value 3000).
+        This parameter set a maximum completion wait time for SYNC mode DMA
+        transfer requests and for RIO_WAIT_FOR_ASYNC ioctl requests.
+
 - 'dbg_level' - This parameter allows to control amount of debug information
         generated by this device driver. This parameter is formed by set of
         bit masks that correspond to the specific functional blocks.