Merge tag 'tty-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty / serial driver updates from Greg KH:
 "Here is the "large" TTY and Serial driver update for 5.3-rc1.

  It's in the negative number of lines overall as we removed an obsolete
  serial driver that was causing problems for some people who were
  trying to clean up some apis (the mpsc.c driver, which only worked for
  some pre-production hardware that no one has anymore.)

  Other than that, lots of tiny changes, cleaning up small things along
  with some platform-specific serial driver updates.

  All of these have been in linux-next for a while now with no reported
  issues"

* tag 'tty-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (68 commits)
  tty: serial: fsl_lpuart: add imx8qxp support
  serial: imx: set_termios(): preserve RTS state
  serial: imx: set_termios(): clarify RTS/CTS bits calculation
  serial: imx: set_termios(): factor-out 'ucr2' initial value
  serial: sh-sci: Terminate TX DMA during buffer flushing
  serial: sh-sci: Fix TX DMA buffer flushing and workqueue races
  serial: mpsc: Remove obsolete MPSC driver
  serial: 8250: 8250_core: Fix missing unlock on error in serial8250_register_8250_port()
  serial: stm32: add RX and TX FIFO flush
  serial: stm32: add support of RX FIFO threshold
  serial: stm32: add support of TX FIFO threshold
  serial: stm32: update PIO transmission
  serial: stm32: add support of timeout interrupt for RX
  Revert "serial: 8250: Don't service RX FIFO if interrupts are disabled"
  tty/serial/8250: use mctrl_gpio helpers
  serial: mctrl_gpio: Check if GPIO property exisits before requesting it
  serial: 8250: pericom_do_set_divisor can be static
  tty: serial_core: Set port active bit in uart_port_activate
  serial: 8250: Add MSR/MCR TIOCM conversion wrapper functions
  serial: 8250: factor out serial8250_{set,clear}_THRI() helpers
  ...

2 files changed, 21 insertions, 2 deletions

diff --git a/Documentation/admin-guide/devices.txt b/Documentation/admin-guide/devices.txt
index 1649117e6087..e56e00655153 100644
--- a/Documentation/admin-guide/devices.txt
+++ b/Documentation/admin-guide/devices.txt
@@ -2693,8 +2693,8 @@
 		 41 = /dev/ttySMX0		Motorola i.MX - port 0
 		 42 = /dev/ttySMX1		Motorola i.MX - port 1
 		 43 = /dev/ttySMX2		Motorola i.MX - port 2
-		 44 = /dev/ttyMM0		Marvell MPSC - port 0
-		 45 = /dev/ttyMM1		Marvell MPSC - port 1
+		 44 = /dev/ttyMM0		Marvell MPSC - port 0 (obsolete unused)
+		 45 = /dev/ttyMM1		Marvell MPSC - port 1 (obsolete unused)
 		 46 = /dev/ttyCPM0		PPC CPM (SCC or SMC) - port 0
 		    ...
 		 47 = /dev/ttyCPM5		PPC CPM (SCC or SMC) - port 5
diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt
index 3cba12f855b7..20d351f268ef 100644
--- a/Documentation/devicetree/bindings/serial/8250.txt
+++ b/Documentation/devicetree/bindings/serial/8250.txt
@@ -53,6 +53,9 @@ Optional properties:
   programmable TX FIFO thresholds.
 - resets : phandle + reset specifier pairs
 - overrun-throttle-ms : how long to pause uart rx when input overrun is encountered.
+- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD
+  line respectively. It will use specified GPIO instead of the peripheral
+  function pin for the UART feature. If unsure, don't specify this property.
 
 Note:
 * fsl,ns16550:
@@ -74,3 +77,19 @@ Example:
 		interrupts = <10>;
 		reg-shift = <2>;
 	};
+
+Example for OMAP UART using GPIO-based modem control signals:
+
+	uart4: serial@49042000 {
+		compatible = "ti,omap3-uart";
+		reg = <0x49042000 0x400>;
+		interrupts = <80>;
+		ti,hwmods = "uart4";
+		clock-frequency = <48000000>;
+		cts-gpios = <&gpio3 5 GPIO_ACTIVE_LOW>;
+		rts-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
+		dtr-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+		dsr-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+		dcd-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+		rng-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+	};