Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC platform updates from Arnd Bergmann:
 "The APM X-Gene platform is now maintained by folks from Ampere
  computing that took over the product line a while ago, this gets
  reflected in the MAINTAINERS file.

  Cleanups continue on the older mach-davinci and mach-pxa platform, to
  get them to be more like the modern ones. For pxa, we now remove the
  Raumfeld platform code as it now works with device tree based booting.

  i.MX adds a couple new features for the i.MX7ULP SoC

  Mediatek gains support for a new SoC: MT7629 is a new wireless router
  platform, following MT7623.

  Aside from those, there are the usual minor cleanups and bugfixes
  across several platforms"

* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (49 commits)
  MAINTAINERS: Update Ampere email address
  usb: ohci-da8xx: remove unused callbacks from platform data
  ARM: davinci: da830-evm: remove legacy usb helpers
  ARM: davinci: omapl138-hawk: remove legacy usb helpers
  usb: ohci-da8xx: add vbus and overcurrent gpios
  ARM: davinci: da830-evm: use gpio lookup entries for usb gpios
  ARM: davinci: omapl138-hawk: use gpio lookup entries for usb gpios
  usb: ohci-da8xx: add a helper pointer to &pdev->dev
  usb: ohci-da8xx: add a new line after local variables
  arm64: meson: enable g12a clock controller
  MAINTAINERS: Add entry for uDPU board
  ARM: davinci: da850-evm: use GPIO hogs instead of the legacy API
  arm: mediatek: add MT7629 smp bring up code
  Revert "ARM: mediatek: add MT7623a smp bringup code"
  dt-bindings: soc: fix typo of MT8173 power dt-bindings
  ARM: meson: remove COMMON_CLK_AMLOGIC selection
  arm64: meson: remove COMMON_CLK_AMLOGIC selection
  ARM: lpc32xx: remove platform data of ARM PL111 LCD controller
  ARM: lpc32xx: remove platform data of ARM PL180 SD/MMC controller
  ARM: lpc32xx: Use kmemdup to replace duplicating its implementation
  ...

4 files changed, 0 insertions, 1207 deletions

diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig
index dc8e4f4b7ade..8839c72fdee3 100644
--- a/arch/arm/mach-pxa/Kconfig
+++ b/arch/arm/mach-pxa/Kconfig
@@ -454,24 +454,6 @@ config MACH_TREO680
 	  Say Y here if you intend to run this kernel on Palm Treo 680
 	  smartphone.
 
-config MACH_RAUMFELD_RC
-	bool "Raumfeld Controller"
-	select CPU_PXA300
-	select POWER_SUPPLY
-	select PXA3xx
-
-config MACH_RAUMFELD_CONNECTOR
-	bool "Raumfeld Connector"
-	select CPU_PXA300
-	select POWER_SUPPLY
-	select PXA3xx
-
-config MACH_RAUMFELD_SPEAKER
-	bool "Raumfeld Speaker"
-	select CPU_PXA300
-	select POWER_SUPPLY
-	select PXA3xx
-
 config PXA_SHARPSL
 	bool "SHARP Zaurus SL-5600, SL-C7xx and SL-Cxx00 Models"
 	select SHARP_PARAM
diff --git a/arch/arm/mach-pxa/Makefile b/arch/arm/mach-pxa/Makefile
index 0a8e9611052f..f70728930c4f 100644
--- a/arch/arm/mach-pxa/Makefile
+++ b/arch/arm/mach-pxa/Makefile
@@ -86,9 +86,6 @@ obj-$(CONFIG_MACH_POODLE)	+= poodle.o
 obj-$(CONFIG_MACH_TOSA)		+= tosa.o
 obj-$(CONFIG_MACH_ICONTROL)     += icontrol.o mxm8x10.o
 obj-$(CONFIG_ARCH_PXA_ESERIES)	+= eseries.o
-obj-$(CONFIG_MACH_RAUMFELD_RC)		+= raumfeld.o
-obj-$(CONFIG_MACH_RAUMFELD_CONNECTOR)	+= raumfeld.o
-obj-$(CONFIG_MACH_RAUMFELD_SPEAKER)	+= raumfeld.o
 obj-$(CONFIG_MACH_ZIPIT2)	+= z2.o
 
 obj-$(CONFIG_PXA_SYSTEMS_CPLDS)	+= pxa_cplds_irqs.o
diff --git a/arch/arm/mach-pxa/include/mach/pxa25x-udc.h b/arch/arm/mach-pxa/include/mach/pxa25x-udc.h
deleted file mode 100644
index e69de29bb2d1..000000000000
--- a/arch/arm/mach-pxa/include/mach/pxa25x-udc.h
+++ /dev/null
diff --git a/arch/arm/mach-pxa/raumfeld.c b/arch/arm/mach-pxa/raumfeld.c
deleted file mode 100644
index e13bfc9b01d2..000000000000
--- a/arch/arm/mach-pxa/raumfeld.c
+++ /dev/null
@@ -1,1186 +0,0 @@
-/*
- * arch/arm/mach-pxa/raumfeld.c
- *
- * Support for the following Raumfeld devices:
- *
- * 	* Controller
- *  	* Connector
- *  	* Speaker S/M
- *
- * See http://www.raumfeld.com for details.
- *
- * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/property.h>
-#include <linux/platform_device.h>
-#include <linux/interrupt.h>
-#include <linux/gpio.h>
-#include <linux/gpio/machine.h>
-#include <linux/smsc911x.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-#include <linux/leds.h>
-#include <linux/w1-gpio.h>
-#include <linux/sched.h>
-#include <linux/pwm.h>
-#include <linux/pwm_backlight.h>
-#include <linux/i2c.h>
-#include <linux/platform_data/i2c-pxa.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/spi_gpio.h>
-#include <linux/lis3lv02d.h>
-#include <linux/pda_power.h>
-#include <linux/power_supply.h>
-#include <linux/regulator/max8660.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/consumer.h>
-#include <linux/delay.h>
-
-#include <asm/system_info.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include "pxa300.h"
-#include <linux/platform_data/usb-ohci-pxa27x.h>
-#include <linux/platform_data/video-pxafb.h>
-#include <linux/platform_data/mmc-pxamci.h>
-#include <linux/platform_data/mtd-nand-pxa3xx.h>
-
-#include "generic.h"
-#include "devices.h"
-
-/* common GPIO	definitions */
-
-/* inputs */
-#define GPIO_ON_OFF		(14)
-#define GPIO_VOLENC_A		(19)
-#define GPIO_VOLENC_B		(20)
-#define GPIO_CHARGE_DONE	(23)
-#define GPIO_CHARGE_IND		(27)
-#define GPIO_TOUCH_IRQ		(32)
-#define GPIO_ETH_IRQ		(40)
-#define GPIO_SPI_MISO		(98)
-#define GPIO_ACCEL_IRQ		(104)
-#define GPIO_RESCUE_BOOT	(115)
-#define GPIO_DOCK_DETECT	(116)
-#define GPIO_KEY1		(117)
-#define GPIO_KEY2		(118)
-#define GPIO_KEY3		(119)
-#define GPIO_CHARGE_USB_OK	(112)
-#define GPIO_CHARGE_DC_OK	(101)
-#define GPIO_CHARGE_USB_SUSP	(102)
-
-/* outputs */
-#define GPIO_SHUTDOWN_SUPPLY	(16)
-#define GPIO_SHUTDOWN_BATT	(18)
-#define GPIO_CHRG_PEN2		(31)
-#define GPIO_TFT_VA_EN		(33)
-#define GPIO_SPDIF_CS		(34)
-#define GPIO_LED2		(35)
-#define GPIO_LED1		(36)
-#define GPIO_SPDIF_RESET	(38)
-#define GPIO_SPI_CLK		(95)
-#define GPIO_MCLK_DAC_CS	(96)
-#define GPIO_SPI_MOSI		(97)
-#define GPIO_W1_PULLUP_ENABLE	(105)
-#define GPIO_DISPLAY_ENABLE	(106)
-#define GPIO_MCLK_RESET		(111)
-#define GPIO_W2W_RESET		(113)
-#define GPIO_W2W_PDN		(114)
-#define GPIO_CODEC_RESET	(120)
-#define GPIO_AUDIO_VA_ENABLE	(124)
-#define GPIO_ACCEL_CS		(125)
-#define GPIO_ONE_WIRE		(126)
-
-/*
- * GPIO configurations
- */
-static mfp_cfg_t raumfeld_controller_pin_config[] __initdata = {
-	/* UART1 */
-	GPIO77_UART1_RXD,
-	GPIO78_UART1_TXD,
-	GPIO79_UART1_CTS,
-	GPIO81_UART1_DSR,
-	GPIO83_UART1_DTR,
-	GPIO84_UART1_RTS,
-
-	/* UART3 */
-	GPIO110_UART3_RXD,
-
-	/* USB Host */
-	GPIO0_2_USBH_PEN,
-	GPIO1_2_USBH_PWR,
-
-	/* I2C */
-	GPIO21_I2C_SCL | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
-	GPIO22_I2C_SDA | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
-
-	/* SPI */
-	GPIO34_GPIO,	/* SPDIF_CS */
-	GPIO96_GPIO,	/* MCLK_CS */
-	GPIO125_GPIO,	/* ACCEL_CS */
-
-	/* MMC */
-	GPIO3_MMC1_DAT0,
-	GPIO4_MMC1_DAT1,
-	GPIO5_MMC1_DAT2,
-	GPIO6_MMC1_DAT3,
-	GPIO7_MMC1_CLK,
-	GPIO8_MMC1_CMD,
-
-	/* One-wire */
-	GPIO126_GPIO | MFP_LPM_FLOAT,
-	GPIO105_GPIO | MFP_PULL_LOW | MFP_LPM_PULL_LOW,
-
-	/* CHRG_USB_OK */
-	GPIO101_GPIO | MFP_PULL_HIGH,
-	/* CHRG_USB_OK */
-	GPIO112_GPIO | MFP_PULL_HIGH,
-	/* CHRG_USB_SUSP */
-	GPIO102_GPIO,
-	/* DISPLAY_ENABLE */
-	GPIO106_GPIO,
-	/* DOCK_DETECT */
-	GPIO116_GPIO | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
-
-	/* LCD */
-	GPIO54_LCD_LDD_0,
-	GPIO55_LCD_LDD_1,
-	GPIO56_LCD_LDD_2,
-	GPIO57_LCD_LDD_3,
-	GPIO58_LCD_LDD_4,
-	GPIO59_LCD_LDD_5,
-	GPIO60_LCD_LDD_6,
-	GPIO61_LCD_LDD_7,
-	GPIO62_LCD_LDD_8,
-	GPIO63_LCD_LDD_9,
-	GPIO64_LCD_LDD_10,
-	GPIO65_LCD_LDD_11,
-	GPIO66_LCD_LDD_12,
-	GPIO67_LCD_LDD_13,
-	GPIO68_LCD_LDD_14,
-	GPIO69_LCD_LDD_15,
-	GPIO70_LCD_LDD_16,
-	GPIO71_LCD_LDD_17,
-	GPIO72_LCD_FCLK,
-	GPIO73_LCD_LCLK,
-	GPIO74_LCD_PCLK,
-	GPIO75_LCD_BIAS,
-};
-
-static mfp_cfg_t raumfeld_connector_pin_config[] __initdata = {
-	/* UART1 */
-	GPIO77_UART1_RXD,
-	GPIO78_UART1_TXD,
-	GPIO79_UART1_CTS,
-	GPIO81_UART1_DSR,
-	GPIO83_UART1_DTR,
-	GPIO84_UART1_RTS,
-
-	/* UART3 */
-	GPIO110_UART3_RXD,
-
-	/* USB Host */
-	GPIO0_2_USBH_PEN,
-	GPIO1_2_USBH_PWR,
-
-	/* I2C */
-	GPIO21_I2C_SCL | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
-	GPIO22_I2C_SDA | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
-
-	/* SPI */
-	GPIO34_GPIO,	/* SPDIF_CS */
-	GPIO96_GPIO,	/* MCLK_CS */
-	GPIO125_GPIO,	/* ACCEL_CS */
-
-	/* MMC */
-	GPIO3_MMC1_DAT0,
-	GPIO4_MMC1_DAT1,
-	GPIO5_MMC1_DAT2,
-	GPIO6_MMC1_DAT3,
-	GPIO7_MMC1_CLK,
-	GPIO8_MMC1_CMD,
-
-	/* Ethernet */
-	GPIO1_nCS2,			/* CS */
-	GPIO40_GPIO | MFP_PULL_HIGH,	/* IRQ */
-
-	/* SSP for I2S */
-	GPIO85_SSP1_SCLK,
-	GPIO89_SSP1_EXTCLK,
-	GPIO86_SSP1_FRM,
-	GPIO87_SSP1_TXD,
-	GPIO88_SSP1_RXD,
-	GPIO90_SSP1_SYSCLK,
-
-	/* SSP2 for S/PDIF */
-	GPIO25_SSP2_SCLK,
-	GPIO26_SSP2_FRM,
-	GPIO27_SSP2_TXD,
-	GPIO29_SSP2_EXTCLK,
-
-	/* LEDs */
-	GPIO35_GPIO | MFP_LPM_PULL_LOW,
-	GPIO36_GPIO | MFP_LPM_DRIVE_HIGH,
-};
-
-static mfp_cfg_t raumfeld_speaker_pin_config[] __initdata = {
-	/* UART1 */
-	GPIO77_UART1_RXD,
-	GPIO78_UART1_TXD,
-	GPIO79_UART1_CTS,
-	GPIO81_UART1_DSR,
-	GPIO83_UART1_DTR,
-	GPIO84_UART1_RTS,
-
-	/* UART3 */
-	GPIO110_UART3_RXD,
-
-	/* USB Host */
-	GPIO0_2_USBH_PEN,
-	GPIO1_2_USBH_PWR,
-
-	/* I2C */
-	GPIO21_I2C_SCL | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
-	GPIO22_I2C_SDA | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
-
-	/* SPI */
-	GPIO34_GPIO,	/* SPDIF_CS */
-	GPIO96_GPIO,	/* MCLK_CS */
-	GPIO125_GPIO,	/* ACCEL_CS */
-
-	/* MMC */
-	GPIO3_MMC1_DAT0,
-	GPIO4_MMC1_DAT1,
-	GPIO5_MMC1_DAT2,
-	GPIO6_MMC1_DAT3,
-	GPIO7_MMC1_CLK,
-	GPIO8_MMC1_CMD,
-
-	/* Ethernet */
-	GPIO1_nCS2,			/* CS */
-	GPIO40_GPIO | MFP_PULL_HIGH,	/* IRQ */
-
-	/* SSP for I2S */
-	GPIO85_SSP1_SCLK,
-	GPIO89_SSP1_EXTCLK,
-	GPIO86_SSP1_FRM,
-	GPIO87_SSP1_TXD,
-	GPIO88_SSP1_RXD,
-	GPIO90_SSP1_SYSCLK,
-
-	/* LEDs */
-	GPIO35_GPIO | MFP_LPM_PULL_LOW,
-	GPIO36_GPIO | MFP_LPM_DRIVE_HIGH,
-};
-
-/*
- * SMSC LAN9220 Ethernet
- */
-
-static struct resource smc91x_resources[] = {
-	{
-		.start	= PXA3xx_CS2_PHYS,
-		.end	= PXA3xx_CS2_PHYS + 0xfffff,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= PXA_GPIO_TO_IRQ(GPIO_ETH_IRQ),
-		.end	= PXA_GPIO_TO_IRQ(GPIO_ETH_IRQ),
-		.flags	= IORESOURCE_IRQ | IRQF_TRIGGER_FALLING,
-	}
-};
-
-static struct smsc911x_platform_config raumfeld_smsc911x_config = {
-	.phy_interface	= PHY_INTERFACE_MODE_MII,
-	.irq_polarity	= SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
-	.irq_type	= SMSC911X_IRQ_TYPE_OPEN_DRAIN,
-	.flags		= SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
-};
-
-static struct platform_device smc91x_device = {
-	.name		= "smsc911x",
-	.id		= -1,
-	.num_resources	= ARRAY_SIZE(smc91x_resources),
-	.resource	= smc91x_resources,
-	.dev		= {
-		.platform_data = &raumfeld_smsc911x_config,
-	}
-};
-
-/**
- * NAND
- */
-
-static struct mtd_partition raumfeld_nand_partitions[] = {
-	{
-		.name		= "Bootloader",
-		.offset		= 0,
-		.size		= 0xa0000,
-		.mask_flags	= MTD_WRITEABLE, /* force read-only */
-	},
-	{
-		.name		= "BootloaderEnvironment",
-		.offset		= 0xa0000,
-		.size		= 0x20000,
-	},
-	{
-		.name		= "BootloaderSplashScreen",
-		.offset		= 0xc0000,
-		.size		= 0x60000,
-	},
-	{
-		.name		= "UBI",
-		.offset		= 0x120000,
-		.size		= MTDPART_SIZ_FULL,
-	},
-};
-
-static struct pxa3xx_nand_platform_data raumfeld_nand_info = {
-	.keep_config	= 1,
-	.parts		= raumfeld_nand_partitions,
-	.nr_parts	= ARRAY_SIZE(raumfeld_nand_partitions),
-};
-
-/**
- * USB (OHCI) support
- */
-
-static struct pxaohci_platform_data raumfeld_ohci_info = {
-	.port_mode      = PMM_GLOBAL_MODE,
-	.flags		= ENABLE_PORT1,
-};
-
-/**
- * Rotary encoder input device
- */
-
-static struct gpiod_lookup_table raumfeld_rotary_gpios_table = {
-	.dev_id = "rotary-encoder.0",
-	.table = {
-		GPIO_LOOKUP_IDX("gpio-0",
-				GPIO_VOLENC_A, NULL, 0, GPIO_ACTIVE_LOW),
-		GPIO_LOOKUP_IDX("gpio-0",
-				GPIO_VOLENC_B, NULL, 1, GPIO_ACTIVE_HIGH),
-		{ },
-	},
-};
-
-static const struct property_entry raumfeld_rotary_properties[] __initconst = {
-	PROPERTY_ENTRY_U32("rotary-encoder,steps-per-period", 24),
-	PROPERTY_ENTRY_U32("linux,axis",		      REL_X),
-	PROPERTY_ENTRY_U32("rotary-encoder,relative_axis",    1),
-	{ },
-};
-
-static struct platform_device rotary_encoder_device = {
-	.name		= "rotary-encoder",
-	.id		= 0,
-};
-
-/**
- * GPIO buttons
- */
-
-static struct gpio_keys_button gpio_keys_button[] = {
-	{
-		.code			= KEY_F1,
-		.type			= EV_KEY,
-		.gpio			= GPIO_KEY1,
-		.active_low		= 1,
-		.wakeup			= 0,
-		.debounce_interval	= 5, /* ms */
-		.desc			= "Button 1",
-	},
-	{
-		.code			= KEY_F2,
-		.type			= EV_KEY,
-		.gpio			= GPIO_KEY2,
-		.active_low		= 1,
-		.wakeup			= 0,
-		.debounce_interval	= 5, /* ms */
-		.desc			= "Button 2",
-	},
-	{
-		.code			= KEY_F3,
-		.type			= EV_KEY,
-		.gpio			= GPIO_KEY3,
-		.active_low		= 1,
-		.wakeup			= 0,
-		.debounce_interval	= 5, /* ms */
-		.desc			= "Button 3",
-	},
-	{
-		.code			= KEY_F4,
-		.type			= EV_KEY,
-		.gpio			= GPIO_RESCUE_BOOT,
-		.active_low		= 0,
-		.wakeup			= 0,
-		.debounce_interval	= 5, /* ms */
-		.desc			= "rescue boot button",
-	},
-	{
-		.code			= KEY_F5,
-		.type			= EV_KEY,
-		.gpio			= GPIO_DOCK_DETECT,
-		.active_low		= 1,
-		.wakeup			= 0,
-		.debounce_interval	= 5, /* ms */
-		.desc			= "dock detect",
-	},
-	{
-		.code			= KEY_F6,
-		.type			= EV_KEY,
-		.gpio			= GPIO_ON_OFF,
-		.active_low		= 0,
-		.wakeup			= 0,
-		.debounce_interval	= 5, /* ms */
-		.desc			= "on_off button",
-	},
-};
-
-static struct gpio_keys_platform_data gpio_keys_platform_data = {
-	.buttons	= gpio_keys_button,
-	.nbuttons	= ARRAY_SIZE(gpio_keys_button),
-	.rep		= 0,
-};
-
-static struct platform_device raumfeld_gpio_keys_device = {
-	.name	= "gpio-keys",
-	.id	= -1,
-	.dev 	= {
-		.platform_data	= &gpio_keys_platform_data,
-	}
-};
-
-/**
- * GPIO LEDs
- */
-
-static struct gpio_led raumfeld_leds[] = {
-	{
-		.name		= "raumfeld:1",
-		.gpio		= GPIO_LED1,
-		.active_low	= 1,
-		.default_state	= LEDS_GPIO_DEFSTATE_ON,
-	},
-	{
-		.name		= "raumfeld:2",
-		.gpio		= GPIO_LED2,
-		.active_low	= 0,
-		.default_state	= LEDS_GPIO_DEFSTATE_OFF,
-	}
-};
-
-static struct gpio_led_platform_data raumfeld_led_platform_data = {
-	.leds		= raumfeld_leds,
-	.num_leds	= ARRAY_SIZE(raumfeld_leds),
-};
-
-static struct platform_device raumfeld_led_device = {
-	.name	= "leds-gpio",
-	.id	= -1,
-	.dev	= {
-		.platform_data = &raumfeld_led_platform_data,
-	},
-};
-
-/**
- * One-wire (W1 bus) support
- */
-
-static void w1_enable_external_pullup(int enable)
-{
-	gpio_set_value(GPIO_W1_PULLUP_ENABLE, enable);
-	msleep(100);
-}
-
-static struct gpiod_lookup_table raumfeld_w1_gpiod_table = {
-	.dev_id = "w1-gpio",
-	.table = {
-		GPIO_LOOKUP_IDX("gpio-pxa", GPIO_ONE_WIRE, NULL, 0,
-				GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
-	},
-};
-
-static struct w1_gpio_platform_data w1_gpio_platform_data = {
-	.enable_external_pullup = w1_enable_external_pullup,
-};
-
-static struct platform_device raumfeld_w1_gpio_device = {
-	.name	= "w1-gpio",
-	.dev	= {
-		.platform_data = &w1_gpio_platform_data
-	}
-};
-
-static void __init raumfeld_w1_init(void)
-{
-	int ret = gpio_request(GPIO_W1_PULLUP_ENABLE,
-			        "W1 external pullup enable");
-
-	if (ret < 0)
-		pr_warn("Unable to request GPIO_W1_PULLUP_ENABLE\n");
-	else
-		gpio_direction_output(GPIO_W1_PULLUP_ENABLE, 0);
-
-	gpiod_add_lookup_table(&raumfeld_w1_gpiod_table);
-	platform_device_register(&raumfeld_w1_gpio_device);
-}
-
-/**
- * Framebuffer device
- */
-
-static struct pwm_lookup raumfeld_pwm_lookup[] = {
-	PWM_LOOKUP("pxa27x-pwm.0", 0, "pwm-backlight", NULL, 10000,
-		   PWM_POLARITY_NORMAL),
-};
-
-/* PWM controlled backlight */
-static struct platform_pwm_backlight_data raumfeld_pwm_backlight_data = {
-	.max_brightness	= 100,
-	.dft_brightness	= 100,
-	.enable_gpio	= -1,
-};
-
-static struct platform_device raumfeld_pwm_backlight_device = {
-	.name	= "pwm-backlight",
-	.dev	= {
-		.parent		= &pxa27x_device_pwm0.dev,
-		.platform_data	= &raumfeld_pwm_backlight_data,
-	}
-};
-
-/* LT3593 controlled backlight */
-static struct gpio_led raumfeld_lt3593_led = {
-	.name		= "backlight",
-	.gpio		= mfp_to_gpio(MFP_PIN_GPIO17),
-	.default_state	= LEDS_GPIO_DEFSTATE_ON,
-};
-
-static struct gpio_led_platform_data raumfeld_lt3593_platform_data = {
-	.leds		= &raumfeld_lt3593_led,
-	.num_leds	= 1,
-};
-
-static struct platform_device raumfeld_lt3593_device = {
-	.name	= "leds-lt3593",
-	.id	= -1,
-	.dev	= {
-		.platform_data = &raumfeld_lt3593_platform_data,
-	},
-};
-
-static struct pxafb_mode_info sharp_lq043t3dx02_mode = {
-	.pixclock	= 111000,
-	.xres		= 480,
-	.yres		= 272,
-	.bpp		= 16,
-	.hsync_len	= 41,
-	.left_margin	= 2,
-	.right_margin	= 1,
-	.vsync_len	= 10,
-	.upper_margin	= 3,
-	.lower_margin	= 1,
-	.sync		= 0,
-};
-
-static struct pxafb_mach_info raumfeld_sharp_lcd_info = {
-	.modes		= &sharp_lq043t3dx02_mode,
-	.num_modes	= 1,
-	.video_mem_size = 0x400000,
-	.lcd_conn	= LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
-#ifdef CONFIG_PXA3XX_GCU
-	.acceleration_enabled = 1,
-#endif
-};
-
-static void __init raumfeld_lcd_init(void)
-{
-	int ret;
-
-	ret = gpio_request(GPIO_TFT_VA_EN, "display VA enable");
-	if (ret < 0)
-		pr_warn("Unable to request GPIO_TFT_VA_EN\n");
-	else
-		gpio_direction_output(GPIO_TFT_VA_EN, 1);
-
-	msleep(100);
-
-	ret = gpio_request(GPIO_DISPLAY_ENABLE, "display enable");
-	if (ret < 0)
-		pr_warn("Unable to request GPIO_DISPLAY_ENABLE\n");
-	else
-		gpio_direction_output(GPIO_DISPLAY_ENABLE, 1);
-
-	/* Hardware revision 2 has the backlight regulator controlled
-	 * by an LT3593, earlier and later devices use PWM for that. */
-	if ((system_rev & 0xff) == 2) {
-		platform_device_register(&raumfeld_lt3593_device);
-	} else {
-		mfp_cfg_t raumfeld_pwm_pin_config = GPIO17_PWM0_OUT;
-		pxa3xx_mfp_config(&raumfeld_pwm_pin_config, 1);
-		pwm_add_table(raumfeld_pwm_lookup,
-			      ARRAY_SIZE(raumfeld_pwm_lookup));
-		platform_device_register(&raumfeld_pwm_backlight_device);
-	}
-
-	pxa_set_fb_info(NULL, &raumfeld_sharp_lcd_info);
-	platform_device_register(&pxa3xx_device_gcu);
-}
-
-/**
- * SPI devices
- */
-
-static struct spi_gpio_platform_data raumfeld_spi_platform_data = {
-	.num_chipselect	= 3,
-};
-
-static struct platform_device raumfeld_spi_device = {
-	.name	= "spi_gpio",
-	.id	= 0,
-	.dev 	= {
-		.platform_data	= &raumfeld_spi_platform_data,
-	}
-};
-
-static struct gpiod_lookup_table raumfeld_spi_gpiod_table = {
-	.dev_id         = "spi_gpio",
-	.table          = {
-		GPIO_LOOKUP("gpio-0", GPIO_SPI_CLK,
-			    "sck", GPIO_ACTIVE_HIGH),
-		GPIO_LOOKUP("gpio-0", GPIO_SPI_MOSI,
-			    "mosi", GPIO_ACTIVE_HIGH),
-		GPIO_LOOKUP("gpio-0", GPIO_SPI_MISO,
-			    "miso", GPIO_ACTIVE_HIGH),
-		GPIO_LOOKUP_IDX("gpio-0", GPIO_SPDIF_CS,
-				"cs", 0, GPIO_ACTIVE_HIGH),
-		GPIO_LOOKUP_IDX("gpio-0", GPIO_ACCEL_CS,
-				"cs", 1, GPIO_ACTIVE_HIGH),
-		GPIO_LOOKUP_IDX("gpio-0", GPIO_MCLK_DAC_CS,
-				"cs", 2, GPIO_ACTIVE_HIGH),
-		{ },
-	},
-};
-
-static struct lis3lv02d_platform_data lis3_pdata = {
-	.click_flags 	= LIS3_CLICK_SINGLE_X |
-			  LIS3_CLICK_SINGLE_Y |
-			  LIS3_CLICK_SINGLE_Z,
-	.irq_cfg	= LIS3_IRQ1_CLICK | LIS3_IRQ2_CLICK,
-	.wakeup_flags	= LIS3_WAKEUP_X_LO | LIS3_WAKEUP_X_HI |
-			  LIS3_WAKEUP_Y_LO | LIS3_WAKEUP_Y_HI |
-			  LIS3_WAKEUP_Z_LO | LIS3_WAKEUP_Z_HI,
-	.wakeup_thresh	= 10,
-	.click_thresh_x = 10,
-	.click_thresh_y = 10,
-	.click_thresh_z = 10,
-};
-
-#define SPI_AK4104	\
-{			\
-	.modalias	= "ak4104-codec",	\
-	.max_speed_hz	= 10000,		\
-	.bus_num	= 0,			\
-	.chip_select	= 0,			\
-}
-
-#define SPI_LIS3	\
-{			\
-	.modalias	= "lis3lv02d_spi",	\
-	.max_speed_hz	= 1000000,		\
-	.bus_num	= 0,			\
-	.chip_select	= 1,			\
-	.platform_data	= &lis3_pdata,		\
-	.irq		= PXA_GPIO_TO_IRQ(GPIO_ACCEL_IRQ),	\
-}
-
-#define SPI_DAC7512	\
-{	\
-	.modalias	= "dac7512",		\
-	.max_speed_hz	= 1000000,		\
-	.bus_num	= 0,			\
-	.chip_select	= 2,			\
-}
-
-static struct spi_board_info connector_spi_devices[] __initdata = {
-	SPI_AK4104,
-	SPI_DAC7512,
-};
-
-static struct spi_board_info speaker_spi_devices[] __initdata = {
-	SPI_DAC7512,
-};
-
-static struct spi_board_info controller_spi_devices[] __initdata = {
-	SPI_LIS3,
-};
-
-/**
- * MMC for Marvell Libertas 8688 via SDIO
- */
-
-static int raumfeld_mci_init(struct device *dev, irq_handler_t isr, void *data)
-{
-	gpio_set_value(GPIO_W2W_RESET, 1);
-	gpio_set_value(GPIO_W2W_PDN, 1);
-
-	return 0;
-}
-
-static void raumfeld_mci_exit(struct device *dev, void *data)
-{
-	gpio_set_value(GPIO_W2W_RESET, 0);
-	gpio_set_value(GPIO_W2W_PDN, 0);
-}
-
-static struct pxamci_platform_data raumfeld_mci_platform_data = {
-	.init			= raumfeld_mci_init,
-	.exit			= raumfeld_mci_exit,
-	.detect_delay_ms	= 200,
-};
-
-/*
- * External power / charge logic
- */
-
-static int power_supply_init(struct device *dev)
-{
-	return 0;
-}
-
-static void power_supply_exit(struct device *dev)
-{
-}
-
-static int raumfeld_is_ac_online(void)
-{
-	return !gpio_get_value(GPIO_CHARGE_DC_OK);
-}
-
-static int raumfeld_is_usb_online(void)
-{
-	return 0;
-}
-
-static char *raumfeld_power_supplicants[] = { "ds2760-battery.0" };
-
-static void raumfeld_power_signal_charged(void)
-{
-	struct power_supply *psy =
-		power_supply_get_by_name(raumfeld_power_supplicants[0]);
-
-	if (psy) {
-		power_supply_set_battery_charged(psy);
-		power_supply_put(psy);
-	}
-}
-
-static int raumfeld_power_resume(void)
-{
-	/* check if GPIO_CHARGE_DONE went low while we were sleeping */
-	if (!gpio_get_value(GPIO_CHARGE_DONE))
-		raumfeld_power_signal_charged();
-
-	return 0;
-}
-
-static struct pda_power_pdata power_supply_info = {
-	.init			= power_supply_init,
-	.is_ac_online		= raumfeld_is_ac_online,
-	.is_usb_online		= raumfeld_is_usb_online,
-	.exit			= power_supply_exit,
-	.supplied_to		= raumfeld_power_supplicants,
-	.num_supplicants	= ARRAY_SIZE(raumfeld_power_supplicants),
-	.resume			= raumfeld_power_resume,
-};
-
-static struct resource power_supply_resources[] = {
-	{
-		.name  = "ac",
-		.flags = IORESOURCE_IRQ |
-			 IORESOURCE_IRQ_HIGHEDGE | IORESOURCE_IRQ_LOWEDGE,
-		.start = GPIO_CHARGE_DC_OK,
-		.end   = GPIO_CHARGE_DC_OK,
-	},
-};
-
-static irqreturn_t charge_done_irq(int irq, void *dev_id)
-{
-	raumfeld_power_signal_charged();
-	return IRQ_HANDLED;
-}
-
-static struct platform_device raumfeld_power_supply = {
-	.name = "pda-power",
-	.id   = -1,
-	.dev  = {
-		.platform_data = &power_supply_info,
-	},
-	.resource      = power_supply_resources,
-	.num_resources = ARRAY_SIZE(power_supply_resources),
-};
-
-static void __init raumfeld_power_init(void)
-{
-	int ret;
-
-	/* Set PEN2 high to enable maximum charge current */
-	ret = gpio_request(GPIO_CHRG_PEN2, "CHRG_PEN2");
-	if (ret < 0)
-		pr_warn("Unable to request GPIO_CHRG_PEN2\n");
-	else
-		gpio_direction_output(GPIO_CHRG_PEN2, 1);
-
-	ret = gpio_request(GPIO_CHARGE_DC_OK, "CABLE_DC_OK");
-	if (ret < 0)
-		pr_warn("Unable to request GPIO_CHARGE_DC_OK\n");
-
-	ret = gpio_request(GPIO_CHARGE_USB_SUSP, "CHARGE_USB_SUSP");
-	if (ret < 0)
-		pr_warn("Unable to request GPIO_CHARGE_USB_SUSP\n");
-	else
-		gpio_direction_output(GPIO_CHARGE_USB_SUSP, 0);
-
-	power_supply_resources[0].start = gpio_to_irq(GPIO_CHARGE_DC_OK);
-	power_supply_resources[0].end = gpio_to_irq(GPIO_CHARGE_DC_OK);
-
-	ret = request_irq(gpio_to_irq(GPIO_CHARGE_DONE),
-			&charge_done_irq, IORESOURCE_IRQ_LOWEDGE,
-			"charge_done", NULL);
-
-	if (ret < 0)
-		printk(KERN_ERR "%s: unable to register irq %d\n", __func__,
-			GPIO_CHARGE_DONE);
-	else
-		platform_device_register(&raumfeld_power_supply);
-}
-
-/* Fixed regulator for AUDIO_VA, 0-0048 maps to the cs4270 codec device */
-
-static struct regulator_consumer_supply audio_va_consumer_supply =
-	REGULATOR_SUPPLY("va", "0-0048");
-
-static struct regulator_init_data audio_va_initdata = {
-	.consumer_supplies = &audio_va_consumer_supply,
-	.num_consumer_supplies = 1,
-	.constraints = {
-		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-	},
-};
-
-static struct fixed_voltage_config audio_va_config = {
-	.supply_name		= "audio_va",
-	.microvolts		= 5000000,
-	.enabled_at_boot	= 0,
-	.init_data		= &audio_va_initdata,
-};
-
-static struct platform_device audio_va_device = {
-	.name	= "reg-fixed-voltage",
-	.id	= 0,
-	.dev	= {
-		.platform_data = &audio_va_config,
-	},
-};
-
-static struct gpiod_lookup_table audio_va_gpiod_table = {
-	.dev_id = "reg-fixed-voltage.0",
-	.table = {
-		GPIO_LOOKUP("gpio-pxa", GPIO_AUDIO_VA_ENABLE,
-			    NULL, GPIO_ACTIVE_HIGH),
-		{ },
-	},
-};
-
-/* Dummy supplies for Codec's VD/VLC */
-
-static struct regulator_consumer_supply audio_dummy_supplies[] = {
-	REGULATOR_SUPPLY("vd", "0-0048"),
-	REGULATOR_SUPPLY("vlc", "0-0048"),
-};
-
-static struct regulator_init_data audio_dummy_initdata = {
-	.consumer_supplies = audio_dummy_supplies,
-	.num_consumer_supplies = ARRAY_SIZE(audio_dummy_supplies),
-	.constraints = {
-		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-	},
-};
-
-static struct fixed_voltage_config audio_dummy_config = {
-	.supply_name		= "audio_vd",
-	.microvolts		= 3300000,
-	.init_data		= &audio_dummy_initdata,
-};
-
-static struct platform_device audio_supply_dummy_device = {
-	.name	= "reg-fixed-voltage",
-	.id	= 1,
-	.dev	= {
-		.platform_data = &audio_dummy_config,
-	},
-};
-
-static struct platform_device *audio_regulator_devices[] = {
-	&audio_va_device,
-	&audio_supply_dummy_device,
-};
-
-/**
- * Regulator support via MAX8660
- */
-
-static struct regulator_consumer_supply vcc_mmc_supply =
-	REGULATOR_SUPPLY("vmmc", "pxa2xx-mci.0");
-
-static struct regulator_init_data vcc_mmc_init_data = {
-	.constraints = {
-		.min_uV			= 3300000,
-		.max_uV			= 3300000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL,
-		.valid_ops_mask		= REGULATOR_CHANGE_STATUS |
-					  REGULATOR_CHANGE_VOLTAGE |
-					  REGULATOR_CHANGE_MODE,
-	},
-	.consumer_supplies = &vcc_mmc_supply,
-	.num_consumer_supplies = 1,
-};
-
-static struct max8660_subdev_data max8660_v6_subdev_data = {
-	.id		= MAX8660_V6,
-	.name		= "vmmc",
-	.platform_data	= &vcc_mmc_init_data,
-};
-
-static struct max8660_platform_data max8660_pdata = {
-	.subdevs = &max8660_v6_subdev_data,
-	.num_subdevs = 1,
-};
-
-/**
- * I2C devices
- */
-
-static struct i2c_board_info raumfeld_pwri2c_board_info = {
-	.type		= "max8660",
-	.addr		= 0x34,
-	.platform_data	= &max8660_pdata,
-};
-
-static struct i2c_board_info raumfeld_connector_i2c_board_info __initdata = {
-	.type	= "cs4270",
-	.addr	= 0x48,
-};
-
-static struct gpiod_lookup_table raumfeld_controller_gpios_table = {
-	.dev_id = "0-000a",
-	.table = {
-		GPIO_LOOKUP("gpio-pxa",
-			    GPIO_TOUCH_IRQ, "attn", GPIO_ACTIVE_HIGH),
-		{ },
-	},
-};
-
-static const struct resource raumfeld_controller_resources[] __initconst = {
-	{
-		.start	= PXA_GPIO_TO_IRQ(GPIO_TOUCH_IRQ),
-		.end	= PXA_GPIO_TO_IRQ(GPIO_TOUCH_IRQ),
-		.flags	= IORESOURCE_IRQ | IRQF_TRIGGER_HIGH,
-	},
-};
-
-static struct i2c_board_info raumfeld_controller_i2c_board_info __initdata = {
-	.type	= "eeti_ts",
-	.addr	= 0x0a,
-	.resources = raumfeld_controller_resources,
-	.num_resources = ARRAY_SIZE(raumfeld_controller_resources),
-};
-
-static struct platform_device *raumfeld_common_devices[] = {
-	&raumfeld_gpio_keys_device,
-	&raumfeld_led_device,
-	&raumfeld_spi_device,
-};
-
-static void __init raumfeld_audio_init(void)
-{
-	int ret;
-
-	ret = gpio_request(GPIO_CODEC_RESET, "cs4270 reset");
-	if (ret < 0)
-		pr_warn("unable to request GPIO_CODEC_RESET\n");
-	else
-		gpio_direction_output(GPIO_CODEC_RESET, 1);
-
-	ret = gpio_request(GPIO_SPDIF_RESET, "ak4104 s/pdif reset");
-	if (ret < 0)
-		pr_warn("unable to request GPIO_SPDIF_RESET\n");
-	else
-		gpio_direction_output(GPIO_SPDIF_RESET, 1);
-
-	ret = gpio_request(GPIO_MCLK_RESET, "MCLK reset");
-	if (ret < 0)
-		pr_warn("unable to request GPIO_MCLK_RESET\n");
-	else
-		gpio_direction_output(GPIO_MCLK_RESET, 1);
-
-	gpiod_add_lookup_table(&audio_va_gpiod_table);
-	platform_add_devices(ARRAY_AND_SIZE(audio_regulator_devices));
-}
-
-static void __init raumfeld_common_init(void)
-{
-	int ret;
-
-	/* The on/off button polarity has changed after revision 1 */
-	if ((system_rev & 0xff) > 1) {
-		int i;
-
-		for (i = 0; i < ARRAY_SIZE(gpio_keys_button); i++)
-			if (!strcmp(gpio_keys_button[i].desc, "on_off button"))
-				gpio_keys_button[i].active_low = 1;
-	}
-
-	enable_irq_wake(IRQ_WAKEUP0);
-
-	pxa3xx_set_nand_info(&raumfeld_nand_info);
-	pxa3xx_set_i2c_power_info(NULL);
-	pxa_set_ohci_info(&raumfeld_ohci_info);
-	pxa_set_mci_info(&raumfeld_mci_platform_data);
-	pxa_set_i2c_info(NULL);
-	pxa_set_ffuart_info(NULL);
-
-	ret = gpio_request(GPIO_W2W_RESET, "Wi2Wi reset");
-	if (ret < 0)
-		pr_warn("Unable to request GPIO_W2W_RESET\n");
-	else
-		gpio_direction_output(GPIO_W2W_RESET, 0);
-
-	ret = gpio_request(GPIO_W2W_PDN, "Wi2Wi powerup");
-	if (ret < 0)
-		pr_warn("Unable to request GPIO_W2W_PDN\n");
-	else
-		gpio_direction_output(GPIO_W2W_PDN, 0);
-
-	/* this can be used to switch off the device */
-	ret = gpio_request(GPIO_SHUTDOWN_SUPPLY, "supply shutdown");
-	if (ret < 0)
-		pr_warn("Unable to request GPIO_SHUTDOWN_SUPPLY\n");
-	else
-		gpio_direction_output(GPIO_SHUTDOWN_SUPPLY, 0);
-
-	gpiod_add_lookup_table(&raumfeld_spi_gpiod_table);
-	platform_add_devices(ARRAY_AND_SIZE(raumfeld_common_devices));
-	i2c_register_board_info(1, &raumfeld_pwri2c_board_info, 1);
-}
-
-static void __init __maybe_unused raumfeld_controller_init(void)
-{
-	int ret;
-
-	pxa3xx_mfp_config(ARRAY_AND_SIZE(raumfeld_controller_pin_config));
-
-	gpiod_add_lookup_table(&raumfeld_rotary_gpios_table);
-	device_add_properties(&rotary_encoder_device.dev,
-			      raumfeld_rotary_properties);
-	platform_device_register(&rotary_encoder_device);
-
-	spi_register_board_info(ARRAY_AND_SIZE(controller_spi_devices));
-
-	gpiod_add_lookup_table(&raumfeld_controller_gpios_table);
-	i2c_register_board_info(0, &raumfeld_controller_i2c_board_info, 1);
-
-	ret = gpio_request(GPIO_SHUTDOWN_BATT, "battery shutdown");
-	if (ret < 0)
-		pr_warn("Unable to request GPIO_SHUTDOWN_BATT\n");
-	else
-		gpio_direction_output(GPIO_SHUTDOWN_BATT, 0);
-
-	raumfeld_common_init();
-	raumfeld_power_init();
-	raumfeld_lcd_init();
-	raumfeld_w1_init();
-}
-
-static void __init __maybe_unused raumfeld_connector_init(void)
-{
-	pxa3xx_mfp_config(ARRAY_AND_SIZE(raumfeld_connector_pin_config));
-	spi_register_board_info(ARRAY_AND_SIZE(connector_spi_devices));
-	i2c_register_board_info(0, &raumfeld_connector_i2c_board_info, 1);
-
-	platform_device_register(&smc91x_device);
-
-	raumfeld_audio_init();
-	raumfeld_common_init();
-}
-
-static void __init __maybe_unused raumfeld_speaker_init(void)
-{
-	pxa3xx_mfp_config(ARRAY_AND_SIZE(raumfeld_speaker_pin_config));
-	spi_register_board_info(ARRAY_AND_SIZE(speaker_spi_devices));
-	i2c_register_board_info(0, &raumfeld_connector_i2c_board_info, 1);
-
-	platform_device_register(&smc91x_device);
-
-	gpiod_add_lookup_table(&raumfeld_rotary_gpios_table);
-	device_add_properties(&rotary_encoder_device.dev,
-			      raumfeld_rotary_properties);
-	platform_device_register(&rotary_encoder_device);
-
-	raumfeld_audio_init();
-	raumfeld_common_init();
-}
-
-/* physical memory regions */
-#define	RAUMFELD_SDRAM_BASE	0xa0000000	/* SDRAM region */
-
-#ifdef CONFIG_MACH_RAUMFELD_RC
-MACHINE_START(RAUMFELD_RC, "Raumfeld Controller")
-	.atag_offset	= 0x100,
-	.init_machine	= raumfeld_controller_init,
-	.map_io		= pxa3xx_map_io,
-	.nr_irqs	= PXA_NR_IRQS,
-	.init_irq	= pxa3xx_init_irq,
-	.handle_irq	= pxa3xx_handle_irq,
-	.init_time	= pxa_timer_init,
-	.restart	= pxa_restart,
-MACHINE_END
-#endif
-
-#ifdef CONFIG_MACH_RAUMFELD_CONNECTOR
-MACHINE_START(RAUMFELD_CONNECTOR, "Raumfeld Connector")
-	.atag_offset	= 0x100,
-	.init_machine	= raumfeld_connector_init,
-	.map_io		= pxa3xx_map_io,
-	.nr_irqs	= PXA_NR_IRQS,
-	.init_irq	= pxa3xx_init_irq,
-	.handle_irq	= pxa3xx_handle_irq,
-	.init_time	= pxa_timer_init,
-	.restart	= pxa_restart,
-MACHINE_END
-#endif
-
-#ifdef CONFIG_MACH_RAUMFELD_SPEAKER
-MACHINE_START(RAUMFELD_SPEAKER, "Raumfeld Speaker")
-	.atag_offset	= 0x100,
-	.init_machine	= raumfeld_speaker_init,
-	.map_io		= pxa3xx_map_io,
-	.nr_irqs	= PXA_NR_IRQS,
-	.init_irq	= pxa3xx_init_irq,
-	.handle_irq	= pxa3xx_handle_irq,
-	.init_time	= pxa_timer_init,
-	.restart	= pxa_restart,
-MACHINE_END
-#endif