diff options
| author |   Linus Torvalds <torvalds@linux-foundation.org> | 2022-10-06 11:13:04 -0700 |
|---|---|---|
| committer | Linus Torvalds <torvalds@linux-foundation.org> | 2022-10-06 11:13:04 -0700 |
| commit | 7171a8da00035e7913c3013ca5fb5beb5b8b22f0 (patch) | |
| tree | 6345bd0f928c7c72ba454cba1b1be56502324443 /arch/arm64/boot/dts/freescale | |
| parent | Merge tag 'arm-drivers-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc (diff) | |
| parent | Revert "ARM: dts: BCM5301X: Add basic PCI controller properties" (diff) | |
| download | linux-dev-7171a8da00035e7913c3013ca5fb5beb5b8b22f0.tar.xz linux-dev-7171a8da00035e7913c3013ca5fb5beb5b8b22f0.zip | |
Merge tag 'arm-dt-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"Most of the changes fall into one of three categories: adding support
for additional devices on existing machines, cleaning up issues found
by the ongoing conversion to machine-readable bindings, and addressing
minor mistakes in the existing DT data.
Across SoC vendors, Qualcomm and Freescale stick out as getting the
most updates, which corresponds to their dominance in the mobile phone
and embedded industrial markets, respectively.
There are 636 non-merge changeset in this branch, which is a little
lower than most times, but more importantly we only add 36 machine
files, which is about half of what we had the past few releases.
Eight new SoCs are added, but all of them are variations of already
supported SoC families, and most of them come with one reference board
design from the SoC vendor:
- Mediatek MT8186 is a Chromebook/Tablet type SoC, similar to the
MT65xx series of phone SoCs, with two Cortex-A76 and six Cortex-A55
cores.
- TI AM62A is another member of the K3 family with Cortex-A53 cores,
this one is targetted at Video/Vision processing for industrial and
automotive applications.
- NXP i.MX8DXL is another chip for this market in the ever-growing
i.MX8 family, this one again with two Cortex-A35 cores.
- Renesas R-Car H3Ne-1.7G (R8A779MB) and R-Car V3H2 (R8A77980A) are
minor updates of R8A77951 and R8A77980, respectively.
- Qualcomm IPQ8064-v2.0, IPQ8062 and IPQ8065 are all variants of the
IPQ8064 chip, with minimally different features.
The AMD Pensando Elba and Apple M1 Ultra SoC support was getting close
this time, but in the end did not make the cut.
The new machines based on existing SoC support are fairly uneventful:
- Sony Xperia 1 IV is a fairly recent phone based on Qualcomm
Snapdragon 8 Gen 1.
- Three Samsung phones based on Snapdragon 410: Galaxy E5, E7 and
Grand Max. These are added for both 32-bit and 64-bit kernels, as
they originally shipped running 32-bit code.
- Two new servers using AST2600 BMCs: AMD DaytonaX and Ampere Mt.
Mitchell
- Three new machines based on Rockchips RK3399 and RK3566: Anberic
RG353P and RG503, Pine64 Pinephone Pro, Open AI Lab
- Multiple NXP i.MX6/i.MX8 based boards: Kontron SL/BL i.MX8MM OSM-S,
i.MX8MM Gateworks GW7904, MSC SM2S-IMX8PLUS SoM and carrier board
- Two development boards in the Microchip AT91 family: SAMA5D3-EDS
and lan966x-pcb8290.
- Minor variants of existing boards using Amlogic, Broadcom, Marvell,
Rockchips, Freescale Layerscape and Socionext Uniphier SoCs"
* tag 'arm-dt-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (617 commits)
Revert "ARM: dts: BCM5301X: Add basic PCI controller properties"
ARM: dts: s5pv210: correct double "pins" in pinmux node
ARM: dts: exynos: fix polarity of VBUS GPIO of Origen
arm64: dts: exynos: fix polarity of "enable" line of NFC chip in TM2
arm64: dts: uniphier: Add L2 cache node
arm64: dts: uniphier: Remove compatible "snps,dw-pcie" from pcie node
arm64: dts: uniphier: Fix opp-table node name for LD20
arm64: dts: uniphier: Add USB-device support for PXs3 reference board
arm64: dts: uniphier: Add ahci controller nodes for PXs3
arm64: dts: uniphier: Use GIC interrupt definitions
arm64: dts: uniphier: Rename gpio-hog nodes
arm64: dts: uniphier: Rename usb-glue node for USB3 to usb-controller
arm64: dts: uniphier: Rename usb-phy node for USB2 to usb-controller
arm64: dts: uniphier: Rename pvtctl node to thermal-sensor
ARM: dts: uniphier: Remove compatible "snps,dw-pcie-ep" from pcie-ep node
ARM: dts: uniphier: Move interrupt-parent property to each child node in uniphier-support-card
ARM: dts: uniphier: Add ahci controller nodes for PXs2
ARM: dts: uniphier: Add ahci controller nodes for Pro4
ARM: dts: uniphier: Use GIC interrupt definitions
ARM: dts: uniphier: Rename gpio-hog node
...
Diffstat (limited to 'arch/arm64/boot/dts/freescale')
53 files changed, 5060 insertions, 196 deletions
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index 8bf7f7ecebaa..3ea9edc87909 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -23,6 +23,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-rdb.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-ten64.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-qds.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2081a-rdb.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb @@ -48,6 +49,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-85bb.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-899b.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-9999.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8dxl-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-data-modul-edm-sbc.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb @@ -55,7 +57,8 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-emcon-avari.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-ctouch2.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-edimm2.2.dtb -dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n801x-s.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-bl.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-bl-osm-s.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-mx8menlo.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen-r2.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-phyboard-polis-rdk.dtb @@ -67,6 +70,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw73xx-0x.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7901.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7902.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7903.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7904.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-nonwifi-dahlia.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-nonwifi-dev.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-wifi-dahlia.dtb @@ -83,6 +87,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mn-venice-gw7902.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk2.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-icore-mx8mp-edimm2.2.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mp-msc-sm2s-ep1.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-tqma8mpql-mba8mpxl.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-venice-gw74xx.dtb diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dts index 6b575efd84a7..73eb6061c73e 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dts @@ -59,6 +59,10 @@ status = "okay"; }; +&enetc_port3 { + status = "okay"; +}; + &i2c3 { eeprom@57 { compatible = "atmel,24c32"; @@ -104,7 +108,10 @@ }; &mscc_felix_port4 { - ethernet = <&enetc_port2>; + status = "okay"; +}; + +&mscc_felix_port5 { status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var2.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var2.dts index 330e34f933a3..113b1df74bf8 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var2.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var2.dts @@ -39,6 +39,10 @@ status = "okay"; }; +&enetc_port3 { + status = "okay"; +}; + &mscc_felix { status = "okay"; }; @@ -60,6 +64,9 @@ }; &mscc_felix_port4 { - ethernet = <&enetc_port2>; + status = "okay"; +}; + +&mscc_felix_port5 { status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts index e0cd1516d05b..ecd2c1ea177f 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts @@ -29,6 +29,9 @@ ethernet3 = &mscc_felix_port1; ethernet4 = &mscc_felix_port2; ethernet5 = &mscc_felix_port3; + ethernet6 = &mscc_felix_port4; + ethernet7 = &mscc_felix_port5; + ethernet8 = &enetc_port3; }; chosen { @@ -151,6 +154,10 @@ status = "okay"; }; +&enetc_port3 { + status = "okay"; +}; + &esdhc { sd-uhs-sdr104; sd-uhs-sdr50; @@ -278,7 +285,10 @@ }; &mscc_felix_port4 { - ethernet = <&enetc_port2>; + status = "okay"; +}; + +&mscc_felix_port5 { status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi index 5627dd7734f3..ac1c3a7e5f7a 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi @@ -1156,6 +1156,7 @@ mscc_felix_port4: port@4 { reg = <4>; phy-mode = "internal"; + ethernet = <&enetc_port2>; status = "disabled"; fixed-link { @@ -1168,6 +1169,7 @@ mscc_felix_port5: port@5 { reg = <5>; phy-mode = "internal"; + ethernet = <&enetc_port3>; status = "disabled"; fixed-link { diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts index fea167d222cf..9b726c2a4842 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts @@ -3,7 +3,7 @@ * Device Tree Include file for Freescale Layerscape-1043A family SoC. * * Copyright 2014-2015 Freescale Semiconductor, Inc. - * Copyright 2018 NXP + * Copyright 2018-2021 NXP * * Mingkai Hu <Mingkai.hu@freescale.com> */ @@ -24,6 +24,22 @@ serial1 = &duart1; serial2 = &duart2; serial3 = &duart3; + sgmii-riser-s1-p1 = &sgmii_phy_s1_p1; + sgmii-riser-s2-p1 = &sgmii_phy_s2_p1; + sgmii-riser-s3-p1 = &sgmii_phy_s3_p1; + sgmii-riser-s4-p1 = &sgmii_phy_s4_p1; + qsgmii-s1-p1 = &qsgmii_phy_s1_p1; + qsgmii-s1-p2 = &qsgmii_phy_s1_p2; + qsgmii-s1-p3 = &qsgmii_phy_s1_p3; + qsgmii-s1-p4 = &qsgmii_phy_s1_p4; + qsgmii-s2-p1 = &qsgmii_phy_s2_p1; + qsgmii-s2-p2 = &qsgmii_phy_s2_p2; + qsgmii-s2-p3 = &qsgmii_phy_s2_p3; + qsgmii-s2-p4 = &qsgmii_phy_s2_p4; + emi1-slot1 = &ls1043mdio_s1; + emi1-slot2 = &ls1043mdio_s2; + emi1-slot3 = &ls1043mdio_s3; + emi1-slot4 = &ls1043mdio_s4; }; chosen { @@ -62,8 +78,11 @@ }; fpga: board-control@2,0 { - compatible = "fsl,ls1043aqds-fpga", "fsl,fpga-qixis"; + compatible = "fsl,ls1043aqds-fpga", "fsl,fpga-qixis", "simple-mfd"; reg = <0x2 0x0 0x0000100>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 2 0 0x100>; }; }; @@ -153,3 +172,153 @@ }; #include "fsl-ls1043-post.dtsi" + +&fman0 { + ethernet@e0000 { + phy-handle = <&qsgmii_phy_s2_p1>; + phy-connection-type = "sgmii"; + }; + + ethernet@e2000 { + phy-handle = <&qsgmii_phy_s2_p2>; + phy-connection-type = "sgmii"; + }; + + ethernet@e4000 { + phy-handle = <&rgmii_phy1>; + phy-connection-type = "rgmii"; + }; + + ethernet@e6000 { + phy-handle = <&rgmii_phy2>; + phy-connection-type = "rgmii"; + }; + + ethernet@e8000 { + phy-handle = <&qsgmii_phy_s2_p3>; + phy-connection-type = "sgmii"; + }; + + ethernet@ea000 { + phy-handle = <&qsgmii_phy_s2_p4>; + phy-connection-type = "sgmii"; + }; + + ethernet@f0000 { /* DTSEC9/10GEC1 */ + fixed-link = <1 1 10000 0 0>; + phy-connection-type = "xgmii"; + }; +}; + +&fpga { + mdio-mux-emi1@54 { + compatible = "mdio-mux-mmioreg", "mdio-mux"; + mdio-parent-bus = <&mdio0>; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x54 1>; /* BRDCFG4 */ + mux-mask = <0xe0>; /* EMI1 */ + + /* On-board RGMII1 PHY */ + ls1043mdio0: mdio@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + rgmii_phy1: ethernet-phy@1 { /* MAC3 */ + reg = <0x1>; + }; + }; + + /* On-board RGMII2 PHY */ + ls1043mdio1: mdio@20 { + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + + rgmii_phy2: ethernet-phy@2 { /* MAC4 */ + reg = <0x2>; + }; + }; + + /* Slot 1 */ + ls1043mdio_s1: mdio@40 { + reg = <0x40>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + qsgmii_phy_s1_p1: ethernet-phy@4 { + reg = <0x4>; + }; + + qsgmii_phy_s1_p2: ethernet-phy@5 { + reg = <0x5>; + }; + + qsgmii_phy_s1_p3: ethernet-phy@6 { + reg = <0x6>; + }; + + qsgmii_phy_s1_p4: ethernet-phy@7 { + reg = <0x7>; + }; + + sgmii_phy_s1_p1: ethernet-phy@1c { + reg = <0x1c>; + }; + }; + + /* Slot 2 */ + ls1043mdio_s2: mdio@60 { + reg = <0x60>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + qsgmii_phy_s2_p1: ethernet-phy@8 { + reg = <0x8>; + }; + + qsgmii_phy_s2_p2: ethernet-phy@9 { + reg = <0x9>; + }; + + qsgmii_phy_s2_p3: ethernet-phy@a { + reg = <0xa>; + }; + + qsgmii_phy_s2_p4: ethernet-phy@b { + reg = <0xb>; + }; + + sgmii_phy_s2_p1: ethernet-phy@1c { + reg = <0x1c>; + }; + }; + + /* Slot 3 */ + ls1043mdio_s3: mdio@80 { + reg = <0x80>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + sgmii_phy_s3_p1: ethernet-phy@1c { + reg = <0x1c>; + }; + }; + + /* Slot 4 */ + ls1043mdio_s4: mdio@a0 { + reg = <0xa0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + sgmii_phy_s4_p1: ethernet-phy@1c { + reg = <0x1c>; + }; + }; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts index b290605e92cf..26f8540cb101 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts @@ -29,23 +29,33 @@ &i2c0 { status = "okay"; + ina220@40 { compatible = "ti,ina220"; reg = <0x40>; shunt-resistor = <1000>; }; + adt7461a@4c { compatible = "adi,adt7461"; reg = <0x4c>; }; + + rtc@51 { + compatible = "nxp,pcf85263"; + reg = <0x51>; + }; + eeprom@52 { compatible = "atmel,24c512"; reg = <0x52>; }; + eeprom@53 { compatible = "atmel,24c512"; reg = <0x53>; }; + rtc@68 { compatible = "pericom,pt7c4338"; reg = <0x68>; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi index ca3d5a90d6d4..704f72caddd3 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi @@ -11,6 +11,7 @@ #include <dt-bindings/clock/fsl,qoriq-clockgen.h> #include <dt-bindings/thermal/thermal.h> #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/gpio/gpio.h> / { compatible = "fsl,ls1043a"; @@ -300,6 +301,8 @@ #address-cells = <2>; #size-cells = <2>; ranges; + dma-ranges = <0x0 0x0 0x0 0x0 0x10000 0x00000000>; + dma-coherent; clockgen: clocking@1ee1000 { compatible = "fsl,ls1043a-clockgen"; @@ -393,7 +396,7 @@ dcfg: dcfg@1ee0000 { compatible = "fsl,ls1043a-dcfg", "syscon"; - reg = <0x0 0x1ee0000 0x0 0x10000>; + reg = <0x0 0x1ee0000 0x0 0x1000>; big-endian; }; @@ -536,7 +539,7 @@ }; i2c0: i2c@2180000 { - compatible = "fsl,vf610-i2c"; + compatible = "fsl,ls1043a-i2c", "fsl,vf610-i2c"; #address-cells = <1>; #size-cells = <0>; reg = <0x0 0x2180000 0x0 0x10000>; @@ -551,7 +554,7 @@ }; i2c1: i2c@2190000 { - compatible = "fsl,vf610-i2c"; + compatible = "fsl,ls1043a-i2c", "fsl,vf610-i2c"; #address-cells = <1>; #size-cells = <0>; reg = <0x0 0x2190000 0x0 0x10000>; @@ -559,11 +562,12 @@ clock-names = "i2c"; clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL QORIQ_CLK_PLL_DIV(1)>; + scl-gpios = <&gpio4 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; status = "disabled"; }; i2c2: i2c@21a0000 { - compatible = "fsl,vf610-i2c"; + compatible = "fsl,ls1043a-i2c", "fsl,vf610-i2c"; #address-cells = <1>; #size-cells = <0>; reg = <0x0 0x21a0000 0x0 0x10000>; @@ -571,11 +575,12 @@ clock-names = "i2c"; clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL QORIQ_CLK_PLL_DIV(1)>; + scl-gpios = <&gpio4 10 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; status = "disabled"; }; i2c3: i2c@21b0000 { - compatible = "fsl,vf610-i2c"; + compatible = "fsl,ls1043a-i2c", "fsl,vf610-i2c"; #address-cells = <1>; #size-cells = <0>; reg = <0x0 0x21b0000 0x0 0x10000>; @@ -583,6 +588,7 @@ clock-names = "i2c"; clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL QORIQ_CLK_PLL_DIV(1)>; + scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; status = "disabled"; }; @@ -810,48 +816,59 @@ QORIQ_CLK_PLL_DIV(1)>; }; - usb0: usb@2f00000 { - compatible = "snps,dwc3"; - reg = <0x0 0x2f00000 0x0 0x10000>; - interrupts = <0 60 0x4>; - dr_mode = "host"; - snps,quirk-frame-length-adjustment = <0x20>; - snps,dis_rxdet_inp3_quirk; - snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>; - status = "disabled"; - }; + aux_bus: aux_bus { + #address-cells = <2>; + #size-cells = <2>; + compatible = "simple-bus"; + ranges; + dma-ranges = <0x0 0x0 0x0 0x0 0x100 0x00000000>; + + usb0: usb@2f00000 { + compatible = "snps,dwc3"; + reg = <0x0 0x2f00000 0x0 0x10000>; + interrupts = <0 60 IRQ_TYPE_LEVEL_HIGH>; + dr_mode = "host"; + snps,quirk-frame-length-adjustment = <0x20>; + snps,dis_rxdet_inp3_quirk; + usb3-lpm-capable; + snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>; + status = "disabled"; + }; - usb1: usb@3000000 { - compatible = "snps,dwc3"; - reg = <0x0 0x3000000 0x0 0x10000>; - interrupts = <0 61 0x4>; - dr_mode = "host"; - snps,quirk-frame-length-adjustment = <0x20>; - snps,dis_rxdet_inp3_quirk; - snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>; - status = "disabled"; - }; + usb1: usb@3000000 { + compatible = "snps,dwc3"; + reg = <0x0 0x3000000 0x0 0x10000>; + interrupts = <0 61 IRQ_TYPE_LEVEL_HIGH>; + dr_mode = "host"; + snps,quirk-frame-length-adjustment = <0x20>; + snps,dis_rxdet_inp3_quirk; + usb3-lpm-capable; + snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>; + status = "disabled"; + }; - usb2: usb@3100000 { - compatible = "snps,dwc3"; - reg = <0x0 0x3100000 0x0 0x10000>; - interrupts = <0 63 0x4>; - dr_mode = "host"; - snps,quirk-frame-length-adjustment = <0x20>; - snps,dis_rxdet_inp3_quirk; - snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>; - status = "disabled"; - }; + usb2: usb@3100000 { + compatible = "snps,dwc3"; + reg = <0x0 0x3100000 0x0 0x10000>; + interrupts = <0 63 IRQ_TYPE_LEVEL_HIGH>; + dr_mode = "host"; + snps,quirk-frame-length-adjustment = <0x20>; + snps,dis_rxdet_inp3_quirk; + usb3-lpm-capable; + snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>; + status = "disabled"; + }; - sata: sata@3200000 { - compatible = "fsl,ls1043a-ahci"; - reg = <0x0 0x3200000 0x0 0x10000>, - <0x0 0x20140520 0x0 0x4>; - reg-names = "ahci", "sata-ecc"; - interrupts = <0 69 0x4>; - clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL - QORIQ_CLK_PLL_DIV(1)>; - dma-coherent; + sata: sata@3200000 { + compatible = "fsl,ls1043a-ahci"; + reg = <0x0 0x3200000 0x0 0x10000>, + <0x0 0x20140520 0x0 0x4>; + reg-names = "ahci", "sata-ecc"; + interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; + dma-coherent; + }; }; msi1: msi-controller1@1571000 { @@ -880,13 +897,12 @@ reg = <0x00 0x03400000 0x0 0x00100000>, /* controller registers */ <0x40 0x00000000 0x0 0x00002000>; /* configuration space */ reg-names = "regs", "config"; - interrupts = <0 118 0x4>, /* controller interrupt */ - <0 117 0x4>; /* PME interrupt */ - interrupt-names = "intr", "pme"; + interrupts = <0 117 IRQ_TYPE_LEVEL_HIGH>, + <0 118 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "pme", "aer"; #address-cells = <3>; #size-cells = <2>; device_type = "pci"; - dma-coherent; num-viewport = <6>; bus-range = <0x0 0xff>; ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000 0x0 0x00010000 /* downstream I/O */ @@ -898,6 +914,8 @@ <0000 0 0 2 &gic 0 111 0x4>, <0000 0 0 3 &gic 0 112 0x4>, <0000 0 0 4 &gic 0 113 0x4>; + fsl,pcie-scfg = <&scfg 0>; + big-endian; status = "disabled"; }; @@ -906,13 +924,12 @@ reg = <0x00 0x03500000 0x0 0x00100000>, /* controller registers */ <0x48 0x00000000 0x0 0x00002000>; /* configuration space */ reg-names = "regs", "config"; - interrupts = <0 128 0x4>, - <0 127 0x4>; - interrupt-names = "intr", "pme"; + interrupts = <0 127 IRQ_TYPE_LEVEL_HIGH>, + <0 128 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "pme", "aer"; #address-cells = <3>; #size-cells = <2>; device_type = "pci"; - dma-coherent; num-viewport = <6>; bus-range = <0x0 0xff>; ranges = <0x81000000 0x0 0x00000000 0x48 0x00010000 0x0 0x00010000 /* downstream I/O */ @@ -924,6 +941,8 @@ <0000 0 0 2 &gic 0 121 0x4>, <0000 0 0 3 &gic 0 122 0x4>, <0000 0 0 4 &gic 0 123 0x4>; + fsl,pcie-scfg = <&scfg 1>; + big-endian; status = "disabled"; }; @@ -932,13 +951,12 @@ reg = <0x00 0x03600000 0x0 0x00100000>, /* controller registers */ <0x50 0x00000000 0x0 0x00002000>; /* configuration space */ reg-names = "regs", "config"; - interrupts = <0 162 0x4>, - <0 161 0x4>; - interrupt-names = "intr", "pme"; + interrupts = <0 161 IRQ_TYPE_LEVEL_HIGH>, + <0 162 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "pme", "aer"; #address-cells = <3>; #size-cells = <2>; device_type = "pci"; - dma-coherent; num-viewport = <6>; bus-range = <0x0 0xff>; ranges = <0x81000000 0x0 0x00000000 0x50 0x00010000 0x0 0x00010000 /* downstream I/O */ @@ -950,6 +968,8 @@ <0000 0 0 2 &gic 0 155 0x4>, <0000 0 0 3 &gic 0 156 0x4>, <0000 0 0 4 &gic 0 157 0x4>; + fsl,pcie-scfg = <&scfg 2>; + big-endian; status = "disabled"; }; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts index eec62c63dafe..b2fcbba60d3a 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts @@ -3,7 +3,7 @@ * Device Tree Include file for Freescale Layerscape-1046A family SoC. * * Copyright 2016 Freescale Semiconductor, Inc. - * Copyright 2018 NXP + * Copyright 2018-2019 NXP * * Shaohui Xie <Shaohui.Xie@nxp.com> */ @@ -17,14 +17,26 @@ compatible = "fsl,ls1046a-qds", "fsl,ls1046a"; aliases { + emi1-slot1 = &ls1046mdio_s1; + emi1-slot2 = &ls1046mdio_s2; + emi1-slot4 = &ls1046mdio_s4; gpio0 = &gpio0; gpio1 = &gpio1; gpio2 = &gpio2; gpio3 = &gpio3; + qsgmii-s2-p1 = &qsgmii_phy_s2_p1; + qsgmii-s2-p2 = &qsgmii_phy_s2_p2; + qsgmii-s2-p3 = &qsgmii_phy_s2_p3; + qsgmii-s2-p4 = &qsgmii_phy_s2_p4; serial0 = &duart0; serial1 = &duart1; serial2 = &duart2; serial3 = &duart3; + sgmii-s1-p1 = &sgmii_phy_s1_p1; + sgmii-s1-p2 = &sgmii_phy_s1_p2; + sgmii-s1-p3 = &sgmii_phy_s1_p3; + sgmii-s1-p4 = &sgmii_phy_s1_p4; + sgmii-s4-p1 = &sgmii_phy_s4_p1; }; chosen { @@ -153,8 +165,9 @@ }; fpga: board-control@2,0 { - compatible = "fsl,ls1046aqds-fpga", "fsl,fpga-qixis"; + compatible = "fsl,ls1046aqds-fpga", "fsl,fpga-qixis", "simple-mfd"; reg = <0x2 0x0 0x0000100>; + ranges = <0 2 0 0x100>; }; }; @@ -169,7 +182,7 @@ compatible = "spansion,m25p80"; #address-cells = <1>; #size-cells = <1>; - spi-max-frequency = <20000000>; + spi-max-frequency = <50000000>; spi-rx-bus-width = <4>; spi-tx-bus-width = <4>; reg = <0>; @@ -177,3 +190,141 @@ }; #include "fsl-ls1046-post.dtsi" + +&fman0 { + ethernet@e0000 { + phy-handle = <&qsgmii_phy_s2_p1>; + phy-connection-type = "sgmii"; + }; + + ethernet@e2000 { + phy-handle = <&sgmii_phy_s4_p1>; + phy-connection-type = "sgmii"; + }; + + ethernet@e4000 { + phy-handle = <&rgmii_phy1>; + phy-connection-type = "rgmii"; + }; + + ethernet@e6000 { + phy-handle = <&rgmii_phy2>; + phy-connection-type = "rgmii"; + }; + + ethernet@e8000 { + phy-handle = <&sgmii_phy_s1_p3>; + phy-connection-type = "sgmii"; + }; + + ethernet@ea000 { + phy-handle = <&sgmii_phy_s1_p4>; + phy-connection-type = "sgmii"; + }; + + ethernet@f0000 { /* DTSEC9/10GEC1 */ + phy-handle = <&sgmii_phy_s1_p1>; + phy-connection-type = "xgmii"; + }; + + ethernet@f2000 { /* DTSEC10/10GEC2 */ + phy-handle = <&sgmii_phy_s1_p2>; + phy-connection-type = "xgmii"; + }; +}; + +&fpga { + #address-cells = <1>; + #size-cells = <1>; + + mdio-mux-emi1 { + compatible = "mdio-mux-mmioreg", "mdio-mux"; + mdio-parent-bus = <&mdio0>; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x54 1>; /* BRDCFG4 */ + mux-mask = <0xe0>; /* EMI1 */ + + /* On-board RGMII1 PHY */ + ls1046mdio0: mdio@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + rgmii_phy1: ethernet-phy@1 { /* MAC3 */ + reg = <0x1>; + }; + }; + + /* On-board RGMII2 PHY */ + ls1046mdio1: mdio@1 { + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + + rgmii_phy2: ethernet-phy@2 { /* MAC4 */ + reg = <0x2>; + }; + }; + + /* Slot 1 */ + ls1046mdio_s1: mdio@2 { + reg = <0x40>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + sgmii_phy_s1_p1: ethernet-phy@1c { + reg = <0x1c>; + }; + + sgmii_phy_s1_p2: ethernet-phy@1d { + reg = <0x1d>; + }; + + sgmii_phy_s1_p3: ethernet-phy@1e { + reg = <0x1e>; + }; + + sgmii_phy_s1_p4: ethernet-phy@1f { + reg = <0x1f>; + }; + }; + + /* Slot 2 */ + ls1046mdio_s2: mdio@3 { + reg = <0x60>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + qsgmii_phy_s2_p1: ethernet-phy@8 { + reg = <0x8>; + }; + + qsgmii_phy_s2_p2: ethernet-phy@9 { + reg = <0x9>; + }; + + qsgmii_phy_s2_p3: ethernet-phy@a { + reg = <0xa>; + }; + + qsgmii_phy_s2_p4: ethernet-phy@b { + reg = <0xb>; + }; + }; + + /* Slot 4 */ + ls1046mdio_s4: mdio@5 { + reg = <0x80>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + sgmii_phy_s4_p1: ethernet-phy@1c { + reg = <0x1c>; + }; + }; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi index feab604322cf..3d9e29824bb2 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi @@ -11,6 +11,7 @@ #include <dt-bindings/clock/fsl,qoriq-clockgen.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/thermal/thermal.h> +#include <dt-bindings/gpio/gpio.h> / { compatible = "fsl,ls1046a"; @@ -272,6 +273,8 @@ #address-cells = <2>; #size-cells = <2>; ranges; + dma-ranges = <0x0 0x0 0x0 0x0 0x10000 0x00000000>; + dma-coherent; ddr: memory-controller@1080000 { compatible = "fsl,qoriq-memory-controller"; @@ -354,7 +357,6 @@ ranges = <0x0 0x00 0x1700000 0x100000>; reg = <0x00 0x1700000 0x0 0x100000>; interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; - dma-coherent; sec_jr0: jr@10000 { compatible = "fsl,sec-v5.4-job-ring", @@ -500,7 +502,7 @@ }; i2c0: i2c@2180000 { - compatible = "fsl,vf610-i2c"; + compatible = "fsl,ls1046a-i2c", "fsl,vf610-i2c"; #address-cells = <1>; #size-cells = <0>; reg = <0x0 0x2180000 0x0 0x10000>; @@ -514,35 +516,38 @@ }; i2c1: i2c@2190000 { - compatible = "fsl,vf610-i2c"; + compatible = "fsl,ls1046a-i2c", "fsl,vf610-i2c"; #address-cells = <1>; #size-cells = <0>; reg = <0x0 0x2190000 0x0 0x10000>; interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL QORIQ_CLK_PLL_DIV(2)>; + scl-gpios = <&gpio3 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; status = "disabled"; }; i2c2: i2c@21a0000 { - compatible = "fsl,vf610-i2c"; + compatible = "fsl,ls1046a-i2c", "fsl,vf610-i2c"; #address-cells = <1>; #size-cells = <0>; reg = <0x0 0x21a0000 0x0 0x10000>; interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL QORIQ_CLK_PLL_DIV(2)>; + scl-gpios = <&gpio3 10 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; status = "disabled"; }; i2c3: i2c@21b0000 { - compatible = "fsl,vf610-i2c"; + compatible = "fsl,ls1046a-i2c", "fsl,vf610-i2c"; #address-cells = <1>; #size-cells = <0>; reg = <0x0 0x21b0000 0x0 0x10000>; interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL QORIQ_CLK_PLL_DIV(2)>; + scl-gpios = <&gpio3 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; status = "disabled"; }; @@ -709,44 +714,55 @@ QORIQ_CLK_PLL_DIV(2)>; }; - usb0: usb@2f00000 { - compatible = "snps,dwc3"; - reg = <0x0 0x2f00000 0x0 0x10000>; - interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>; - dr_mode = "host"; - snps,quirk-frame-length-adjustment = <0x20>; - snps,dis_rxdet_inp3_quirk; - snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>; - }; - - usb1: usb@3000000 { - compatible = "snps,dwc3"; - reg = <0x0 0x3000000 0x0 0x10000>; - interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; - dr_mode = "host"; - snps,quirk-frame-length-adjustment = <0x20>; - snps,dis_rxdet_inp3_quirk; - snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>; - }; - - usb2: usb@3100000 { - compatible = "snps,dwc3"; - reg = <0x0 0x3100000 0x0 0x10000>; - interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>; - dr_mode = "host"; - snps,quirk-frame-length-adjustment = <0x20>; - snps,dis_rxdet_inp3_quirk; - snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>; - }; - - sata: sata@3200000 { - compatible = "fsl,ls1046a-ahci"; - reg = <0x0 0x3200000 0x0 0x10000>, - <0x0 0x20140520 0x0 0x4>; - reg-names = "ahci", "sata-ecc"; - interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL - QORIQ_CLK_PLL_DIV(2)>; + aux_bus: aux_bus { + #address-cells = <2>; + #size-cells = <2>; + compatible = "simple-bus"; + ranges; + dma-ranges = <0x0 0x0 0x0 0x0 0x100 0x00000000>; + + usb0: usb@2f00000 { + compatible = "snps,dwc3"; + reg = <0x0 0x2f00000 0x0 0x10000>; + interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>; + dr_mode = "host"; + snps,quirk-frame-length-adjustment = <0x20>; + snps,dis_rxdet_inp3_quirk; + snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>; + usb3-lpm-capable; + }; + + usb1: usb@3000000 { + compatible = "snps,dwc3"; + reg = <0x0 0x3000000 0x0 0x10000>; + interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; + dr_mode = "host"; + snps,quirk-frame-length-adjustment = <0x20>; + snps,dis_rxdet_inp3_quirk; + snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>; + usb3-lpm-capable; + }; + + usb2: usb@3100000 { + compatible = "snps,dwc3"; + reg = <0x0 0x3100000 0x0 0x10000>; + interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>; + dr_mode = "host"; + snps,quirk-frame-length-adjustment = <0x20>; + snps,dis_rxdet_inp3_quirk; + snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>; + usb3-lpm-capable; + }; + + sata: sata@3200000 { + compatible = "fsl,ls1046a-ahci"; + reg = <0x0 0x3200000 0x0 0x10000>, + <0x0 0x20140520 0x0 0x4>; + reg-names = "ahci", "sata-ecc"; + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; + }; }; msi1: msi-controller@1580000 { @@ -790,7 +806,6 @@ #address-cells = <3>; #size-cells = <2>; device_type = "pci"; - dma-coherent; num-viewport = <8>; bus-range = <0x0 0xff>; ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000 0x0 0x00010000 /* downstream I/O */ @@ -802,6 +817,7 @@ <0000 0 0 2 &gic GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>, <0000 0 0 3 &gic GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>, <0000 0 0 4 &gic GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; + big-endian; status = "disabled"; }; @@ -810,8 +826,11 @@ reg = <0x00 0x03400000 0x0 0x00100000>, <0x40 0x00000000 0x8 0x00000000>; reg-names = "regs", "addr_space"; + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "pme"; num-ib-windows = <6>; num-ob-windows = <8>; + big-endian; status = "disabled"; }; @@ -826,7 +845,6 @@ #address-cells = <3>; #size-cells = <2>; device_type = "pci"; - dma-coherent; num-viewport = <8>; bus-range = <0x0 0xff>; ranges = <0x81000000 0x0 0x00000000 0x48 0x00010000 0x0 0x00010000 /* downstream I/O */ @@ -838,6 +856,7 @@ <0000 0 0 2 &gic GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>, <0000 0 0 3 &gic GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>, <0000 0 0 4 &gic GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + big-endian; status = "disabled"; }; @@ -846,8 +865,11 @@ reg = <0x00 0x03500000 0x0 0x00100000>, <0x48 0x00000000 0x8 0x00000000>; reg-names = "regs", "addr_space"; + interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "pme"; num-ib-windows = <6>; num-ob-windows = <8>; + big-endian; status = "disabled"; }; @@ -862,7 +884,6 @@ #address-cells = <3>; #size-cells = <2>; device_type = "pci"; - dma-coherent; num-viewport = <8>; bus-range = <0x0 0xff>; ranges = <0x81000000 0x0 0x00000000 0x50 0x00010000 0x0 0x00010000 /* downstream I/O */ @@ -874,6 +895,7 @@ <0000 0 0 2 &gic GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>, <0000 0 0 3 &gic GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>, <0000 0 0 4 &gic GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; + big-endian; status = "disabled"; }; @@ -882,8 +904,11 @@ reg = <0x00 0x03600000 0x0 0x00100000>, <0x50 0x00000000 0x8 0x00000000>; reg-names = "regs", "addr_space"; + interrupts = <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "pme"; num-ib-windows = <6>; num-ob-windows = <8>; + big-endian; status = "disabled"; }; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts index 44894356059c..8b6915136997 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts @@ -14,6 +14,7 @@ #include "fsl-ls2080a.dtsi" #include "fsl-ls208xa-rdb.dtsi" +#include <dt-bindings/interrupt-controller/arm-gic.h> / { model = "Freescale Layerscape 2080a RDB Board"; @@ -23,3 +24,71 @@ stdout-path = "serial1:115200n8"; }; }; + +&dpmac5 { + phy-handle = <&mdio2_phy1>; + phy-connection-type = "10gbase-r"; +}; + +&dpmac6 { + phy-handle = <&mdio2_phy2>; + phy-connection-type = "10gbase-r"; +}; + +&dpmac7 { + phy-handle = <&mdio2_phy3>; + phy-connection-type = "10gbase-r"; +}; + +&dpmac8 { + phy-handle = <&mdio2_phy4>; + phy-connection-type = "10gbase-r"; +}; + +&emdio1 { + status = "disabled"; + + /* CS4340 PHYs */ + mdio1_phy1: emdio1-phy@10 { + reg = <0x10>; + }; + + mdio1_phy2: emdio1-phy@11 { + reg = <0x11>; + }; + + mdio1_phy3: emdio1-phy@12 { + reg = <0x12>; + }; + + mdio1_phy4: emdio1-phy@13 { + reg = <0x13>; + }; +}; + +&emdio2 { + /* AQR405 PHYs */ + mdio2_phy1: emdio2-phy@0 { + compatible = "ethernet-phy-ieee802.3-c45"; + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0>; + }; + + mdio2_phy2: emdio2-phy@1 { + compatible = "ethernet-phy-ieee802.3-c45"; + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x1>; + }; + + mdio2_phy3: emdio2-phy@2 { + compatible = "ethernet-phy-ieee802.3-c45"; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x2>; + }; + + mdio2_phy4: emdio2-phy@3 { + compatible = "ethernet-phy-ieee802.3-c45"; + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x3>; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi index 6f6667b70028..a2cadf757148 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi @@ -150,3 +150,7 @@ ranges = <0x81000000 0x0 0x00000000 0x16 0x00010000 0x0 0x00010000 /* downstream I/O */ 0x82000000 0x0 0x40000000 0x16 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ }; + +&timer { + fsl,erratum-a008585; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2081a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls2081a-rdb.dts new file mode 100644 index 000000000000..4461e16fd53a --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-ls2081a-rdb.dts @@ -0,0 +1,132 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Device Tree file for NXP LS2081A RDB Board. + * + * Copyright 2017 NXP + * + * Priyanka Jain <priyanka.jain@nxp.com> + * + */ + +/dts-v1/; + +#include "fsl-ls2088a.dtsi" + +/ { + model = "NXP Layerscape 2081A RDB Board"; + compatible = "fsl,ls2081a-rdb", "fsl,ls2081a"; + + aliases { + serial0 = &serial0; + serial1 = &serial1; + }; + + chosen { + stdout-path = "serial1:115200n8"; + }; +}; + +&dspi { + status = "okay"; + + n25q512a: flash@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <3000000>; + reg = <0>; + }; +}; + +&esdhc { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + + pca9547: mux@75 { + compatible = "nxp,pca9547"; + reg = <0x75>; + #address-cells = <1>; + #size-cells = <0>; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x1>; + + rtc@51 { + compatible = "nxp,pcf2129"; + reg = <0x51>; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x2>; + + ina220@40 { + compatible = "ti,ina220"; + reg = <0x40>; + shunt-resistor = <500>; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x3>; + + adt7481@4c { + compatible = "adi,adt7461"; + reg = <0x4c>; + }; + }; + }; +}; + +&ifc { + status = "disabled"; +}; + +&qspi { + status = "okay"; + + s25fs512s0: flash@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + spi-rx-bus-width = <4>; + spi-tx-bus-width = <4>; + spi-max-frequency = <20000000>; + reg = <0>; + }; + + s25fs512s1: flash@1 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + spi-rx-bus-width = <4>; + spi-tx-bus-width = <4>; + spi-max-frequency = <20000000>; + reg = <1>; + }; +}; + +&sata0 { + status = "okay"; +}; + +&sata1 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi index 6fab73d484b6..f598669e742f 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi @@ -9,6 +9,27 @@ * */ +/* Update DPMAC connections to external PHYs, under SerDes 0x2a_0x49. */ +&dpmac9 { + phy-handle = <&mdio0_phy12>; + phy-connection-type = "sgmii"; +}; + +&dpmac10 { + phy-handle = <&mdio0_phy13>; + phy-connection-type = "sgmii"; +}; + +&dpmac11 { + phy-handle = <&mdio0_phy14>; + phy-connection-type = "sgmii"; +}; + +&dpmac12 { + phy-handle = <&mdio0_phy15>; + phy-connection-type = "sgmii"; +}; + &esdhc { mmc-hs200-1_8v; status = "okay"; @@ -36,9 +57,47 @@ reg = <0x2 0x0 0x10000>; }; - cpld@3,0 { - reg = <0x3 0x0 0x10000>; - compatible = "fsl,ls2080aqds-fpga", "fsl,fpga-qixis"; + boardctrl: board-control@3,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,ls208xaqds-fpga", "fsl,fpga-qixis", "simple-mfd"; + reg = <3 0 0x1000>; + ranges = <0 3 0 0x1000>; + + mdio-mux-emi1@54 { + compatible = "mdio-mux-mmioreg", "mdio-mux"; + mdio-parent-bus = <&emdio1>; + reg = <0x54 1>; /* BRDCFG4 */ + mux-mask = <0xe0>; /* EMI1_MDIO */ + #address-cells=<1>; + #size-cells = <0>; + + /* Child MDIO buses, one for each riser card: + * reg = 0x0, 0x20, 0x40, 0x60, 0x80, 0xa0. + * VSC8234 PHYs on the riser cards. + */ + mdio_mux3: mdio@60 { + reg = <0x60>; + #address-cells = <1>; + #size-cells = <0>; + + mdio0_phy12: mdio-phy0@1c { + reg = <0x1c>; + }; + + mdio0_phy13: mdio-phy1@1d { + reg = <0x1d>; + }; + + mdio0_phy14: mdio-phy2@1e { + reg = <0x1e>; + }; + + mdio0_phy15: mdio-phy3@1f { + reg = <0x1f>; + }; + }; + }; }; }; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi index f8135c5c252d..3d9647b3da14 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi @@ -49,6 +49,8 @@ reg = <0x75>; #address-cells = <1>; #size-cells = <0>; + idle-state = <0>; + i2c@1 { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi index d76f1c42f3fa..f1b9cc8714dc 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi @@ -239,13 +239,12 @@ }; }; - timer { + timer: timer { compatible = "arm,armv8-timer"; interrupts = <1 13 4>, /* Physical Secure PPI, active-low */ <1 14 4>, /* Physical Non-Secure PPI, active-low */ <1 11 4>, /* Virtual PPI, active-low */ <1 10 4>; /* Hypervisor PPI, active-low */ - fsl,erratum-a008585; }; pmu { diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi index 8b5cad4e2700..7d5183c6c5be 100644 --- a/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi @@ -10,7 +10,7 @@ ddr_subsys: bus@5c000000 { #size-cells = <1>; ranges = <0x5c000000 0x0 0x5c000000 0x1000000>; - ddr-pmu@5c020000 { + ddr_pmu0: ddr-pmu@5c020000 { compatible = "fsl,imx8-ddr-pmu"; reg = <0x5c020000 0x10000>; interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi index 960a802b8b6e..d7b4229bb4a2 100644 --- a/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi @@ -111,8 +111,9 @@ dma_subsys: bus@5a000000 { i2c0: i2c@5a800000 { reg = <0x5a800000 0x4000>; interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&i2c0_lpcg IMX_LPCG_CLK_0>; - clock-names = "per"; + clocks = <&i2c0_lpcg IMX_LPCG_CLK_0>, + <&i2c0_lpcg IMX_LPCG_CLK_4>; + clock-names = "per", "ipg"; assigned-clocks = <&clk IMX_SC_R_I2C_0 IMX_SC_PM_CLK_PER>; assigned-clock-rates = <24000000>; power-domains = <&pd IMX_SC_R_I2C_0>; @@ -122,8 +123,9 @@ dma_subsys: bus@5a000000 { i2c1: i2c@5a810000 { reg = <0x5a810000 0x4000>; interrupts = <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&i2c1_lpcg IMX_LPCG_CLK_0>; - clock-names = "per"; + clocks = <&i2c1_lpcg IMX_LPCG_CLK_0>, + <&i2c1_lpcg IMX_LPCG_CLK_4>; + clock-names = "per", "ipg"; assigned-clocks = <&clk IMX_SC_R_I2C_1 IMX_SC_PM_CLK_PER>; assigned-clock-rates = <24000000>; power-domains = <&pd IMX_SC_R_I2C_1>; @@ -133,8 +135,9 @@ dma_subsys: bus@5a000000 { i2c2: i2c@5a820000 { reg = <0x5a820000 0x4000>; interrupts = <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&i2c2_lpcg IMX_LPCG_CLK_0>; - clock-names = "per"; + clocks = <&i2c2_lpcg IMX_LPCG_CLK_0>, + <&i2c2_lpcg IMX_LPCG_CLK_4>; + clock-names = "per", "ipg"; assigned-clocks = <&clk IMX_SC_R_I2C_2 IMX_SC_PM_CLK_PER>; assigned-clock-rates = <24000000>; power-domains = <&pd IMX_SC_R_I2C_2>; @@ -144,8 +147,9 @@ dma_subsys: bus@5a000000 { i2c3: i2c@5a830000 { reg = <0x5a830000 0x4000>; interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&i2c3_lpcg IMX_LPCG_CLK_0>; - clock-names = "per"; + clocks = <&i2c3_lpcg IMX_LPCG_CLK_0>, + <&i2c3_lpcg IMX_LPCG_CLK_4>; + clock-names = "per", "ipg"; assigned-clocks = <&clk IMX_SC_R_I2C_3 IMX_SC_PM_CLK_PER>; assigned-clock-rates = <24000000>; power-domains = <&pd IMX_SC_R_I2C_3>; diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts new file mode 100644 index 000000000000..ca2a43e0cbf6 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts @@ -0,0 +1,426 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2019~2020, 2022 NXP + */ + +/dts-v1/; + +#include "imx8dxl.dtsi" + +/ { + model = "Freescale i.MX8DXL EVK"; + compatible = "fsl,imx8dxl-evk", "fsl,imx8dxl"; + + aliases { + i2c2 = &i2c2; + mmc0 = &usdhc1; + mmc1 = &usdhc2; + serial0 = &lpuart0; + }; + + chosen { + stdout-path = &lpuart0; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x00000000 0x80000000 0 0x40000000>; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + /* + * Memory reserved for optee usage. Please do not use. + * This will be automatically added to dtb if OP-TEE is installed. + * optee@96000000 { + * reg = <0 0x96000000 0 0x2000000>; + * no-map; + * }; + */ + + /* global autoconfigured region for contiguous allocations */ + linux,cma { + compatible = "shared-dma-pool"; + reusable; + size = <0 0x14000000>; + alloc-ranges = <0 0x98000000 0 0x14000000>; + linux,cma-default; + }; + }; + + mux3_en: regulator-0 { + compatible = "regulator-fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "mux3_en"; + gpio = <&pca6416_2 8 GPIO_ACTIVE_LOW>; + regulator-always-on; + }; + + reg_fec1_sel: regulator-1 { + compatible = "regulator-fixed"; + regulator-name = "fec1_supply"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&pca6416_1 11 GPIO_ACTIVE_LOW>; + regulator-always-on; + status = "disabled"; + }; + + reg_fec1_io: regulator-2 { + compatible = "regulator-fixed"; + regulator-name = "fec1_io_supply"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&max7322 0 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + status = "disabled"; + }; + + reg_usdhc2_vmmc: regulator-3 { + compatible = "regulator-fixed"; + regulator-name = "SD1_SPWR"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + gpio = <&lsio_gpio4 30 GPIO_ACTIVE_HIGH>; + enable-active-high; + off-on-delay-us = <3480>; + }; +}; + +&eqos { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_eqos>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + nvmem-cells = <&fec_mac1>; + nvmem-cell-names = "mac-address"; + snps,reset-gpios = <&pca6416_1 2 GPIO_ACTIVE_LOW>; + snps,reset-delays-us = <10 20 200000>; + status = "okay"; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + eee-broken-1000t; + qca,disable-smarteee; + vddio-supply = <&vddio0>; + + vddio0: vddio-regulator { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; + }; +}; + +/* + * fec1 shares the some PINs with usdhc2. + * by default usdhc2 is enabled in this dts. + * Please disable usdhc2 to enable fec1 + */ +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-mode = "rgmii-txid"; + phy-handle = <ðphy1>; + fsl,magic-packet; + rx-internal-delay-ps = <2000>; + nvmem-cells = <&fec_mac0>; + nvmem-cell-names = "mac-address"; + status = "disabled"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + reset-gpios = <&pca6416_1 0 GPIO_ACTIVE_LOW>; + reset-assert-us = <10000>; + qca,disable-smarteee; + vddio-supply = <&vddio1>; + + vddio1: vddio-regulator { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; + }; +}; + +&i2c2 { + #address-cells = <1>; + #size-cells = <0>; + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + pca6416_1: gpio@20 { + compatible = "ti,tca6416"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + }; + + pca6416_2: gpio@21 { + compatible = "ti,tca6416"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + }; + + pca9548_1: i2c-mux@70 { + compatible = "nxp,pca9548"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x70>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0>; + + max7322: gpio@68 { + compatible = "maxim,max7322"; + reg = <0x68>; + gpio-controller; + #gpio-cells = <2>; + status = "disabled"; + }; + }; + + i2c@4 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x4>; + }; + + i2c@5 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x5>; + }; + + i2c@6 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x6>; + }; + }; +}; + +&lpuart0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lpuart0>; + status = "okay"; +}; + +&lsio_gpio4 { + status = "okay"; +}; + +&lsio_gpio5 { + status = "okay"; +}; + +&thermal_zones { + pmic-thermal0 { + polling-delay-passive = <250>; + polling-delay = <2000>; + thermal-sensors = <&tsens IMX_SC_R_PMIC_0>; + + trips { + pmic_alert0: trip0 { + temperature = <110000>; + hysteresis = <2000>; + type = "passive"; + }; + + pmic_crit0: trip1 { + temperature = <125000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&pmic_alert0>; + cooling-device = + <&A35_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&A35_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + bus-width = <8>; + no-sd; + no-sdio; + non-removable; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + bus-width = <4>; + vmmc-supply = <®_usdhc2_vmmc>; + cd-gpios = <&lsio_gpio5 1 GPIO_ACTIVE_LOW>; + wp-gpios = <&lsio_gpio5 0 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_hog: hoggrp { + fsl,pins = < + IMX8DXL_COMP_CTL_GPIO_1V8_3V3_GPIORHB_PAD 0x000514a0 + IMX8DXL_COMP_CTL_GPIO_1V8_3V3_GPIORHK_PAD 0x000014a0 + IMX8DXL_SPI3_CS0_ADMA_ACM_MCLK_OUT1 0x0600004c + IMX8DXL_SNVS_TAMPER_OUT1_LSIO_GPIO2_IO05_IN 0x0600004c + >; + }; + + pinctrl_usbotg1: usbotg1grp { + fsl,pins = < + IMX8DXL_USB_SS3_TC0_CONN_USB_OTG1_PWR 0x00000021 + >; + }; + + pinctrl_usbotg2: usbotg2grp { + fsl,pins = < + IMX8DXL_USB_SS3_TC1_CONN_USB_OTG2_PWR 0x00000021 + >; + }; + + pinctrl_eqos: eqosgrp { + fsl,pins = < + IMX8DXL_ENET0_MDC_CONN_EQOS_MDC 0x06000020 + IMX8DXL_ENET0_MDIO_CONN_EQOS_MDIO 0x06000020 + IMX8DXL_ENET1_RGMII_RXC_CONN_EQOS_RGMII_RXC 0x06000020 + IMX8DXL_ENET1_RGMII_RXD0_CONN_EQOS_RGMII_RXD0 0x06000020 + IMX8DXL_ENET1_RGMII_RXD1_CONN_EQOS_RGMII_RXD1 0x06000020 + IMX8DXL_ENET1_RGMII_RXD2_CONN_EQOS_RGMII_RXD2 0x06000020 + IMX8DXL_ENET1_RGMII_RXD3_CONN_EQOS_RGMII_RXD3 0x06000020 + IMX8DXL_ENET1_RGMII_RX_CTL_CONN_EQOS_RGMII_RX_CTL 0x06000020 + IMX8DXL_ENET1_RGMII_TXC_CONN_EQOS_RGMII_TXC 0x06000020 + IMX8DXL_ENET1_RGMII_TXD0_CONN_EQOS_RGMII_TXD0 0x06000020 + IMX8DXL_ENET1_RGMII_TXD1_CONN_EQOS_RGMII_TXD1 0x06000020 + IMX8DXL_ENET1_RGMII_TXD2_CONN_EQOS_RGMII_TXD2 0x06000020 + IMX8DXL_ENET1_RGMII_TXD3_CONN_EQOS_RGMII_TXD3 0x06000020 + IMX8DXL_ENET1_RGMII_TX_CTL_CONN_EQOS_RGMII_TX_CTL 0x06000020 + >; + }; + + pinctrl_fec1: fec1grp { + fsl,pins = < + IMX8DXL_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB0_PAD 0x000014a0 + IMX8DXL_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB1_PAD 0x000014a0 + IMX8DXL_ENET0_MDC_CONN_ENET0_MDC 0x06000020 + IMX8DXL_ENET0_MDIO_CONN_ENET0_MDIO 0x06000020 + IMX8DXL_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC 0x00000060 + IMX8DXL_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0 0x00000060 + IMX8DXL_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1 0x00000060 + IMX8DXL_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2 0x00000060 + IMX8DXL_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3 0x00000060 + IMX8DXL_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL 0x00000060 + IMX8DXL_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC 0x00000060 + IMX8DXL_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0 0x00000060 + IMX8DXL_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1 0x00000060 + IMX8DXL_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2 0x00000060 + IMX8DXL_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3 0x00000060 + IMX8DXL_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL 0x00000060 + >; + }; + + pinctrl_lpspi3: lpspi3grp { + fsl,pins = < + IMX8DXL_SPI3_SCK_ADMA_SPI3_SCK 0x6000040 + IMX8DXL_SPI3_SDO_ADMA_SPI3_SDO 0x6000040 + IMX8DXL_SPI3_SDI_ADMA_SPI3_SDI 0x6000040 + IMX8DXL_SPI3_CS1_ADMA_SPI3_CS1 0x6000040 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + IMX8DXL_SPI1_SCK_ADMA_I2C2_SDA 0x06000021 + IMX8DXL_SPI1_SDO_ADMA_I2C2_SCL 0x06000021 + >; + }; + + pinctrl_cm40_lpuart: cm40lpuartgrp { + fsl,pins = < + IMX8DXL_ADC_IN2_M40_UART0_RX 0x06000020 + IMX8DXL_ADC_IN3_M40_UART0_TX 0x06000020 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + IMX8DXL_SPI1_CS0_ADMA_I2C3_SDA 0x06000021 + IMX8DXL_SPI1_SDI_ADMA_I2C3_SCL 0x06000021 + >; + }; + + pinctrl_lpuart0: lpuart0grp { + fsl,pins = < + IMX8DXL_UART0_RX_ADMA_UART0_RX 0x06000020 + IMX8DXL_UART0_TX_ADMA_UART0_TX 0x06000020 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + IMX8DXL_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041 + IMX8DXL_EMMC0_CMD_CONN_EMMC0_CMD 0x00000021 + IMX8DXL_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000021 + IMX8DXL_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000021 + IMX8DXL_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000021 + IMX8DXL_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000021 + IMX8DXL_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000021 + IMX8DXL_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000021 + IMX8DXL_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000021 + IMX8DXL_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000021 + IMX8DXL_EMMC0_STROBE_CONN_EMMC0_STROBE 0x00000041 + >; + }; + + pinctrl_usdhc2_gpio: usdhc2gpiogrp { + fsl,pins = < + IMX8DXL_ENET0_RGMII_TX_CTL_LSIO_GPIO4_IO30 0x00000040 /* RESET_B */ + IMX8DXL_ENET0_RGMII_TXD1_LSIO_GPIO5_IO00 0x00000021 /* WP */ + IMX8DXL_ENET0_RGMII_TXD2_LSIO_GPIO5_IO01 0x00000021 /* CD */ + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + IMX8DXL_ENET0_RGMII_RXC_CONN_USDHC1_CLK 0x06000041 + IMX8DXL_ENET0_RGMII_RX_CTL_CONN_USDHC1_CMD 0x00000021 + IMX8DXL_ENET0_RGMII_RXD0_CONN_USDHC1_DATA0 0x00000021 + IMX8DXL_ENET0_RGMII_RXD1_CONN_USDHC1_DATA1 0x00000021 + IMX8DXL_ENET0_RGMII_RXD2_CONN_USDHC1_DATA2 0x00000021 + IMX8DXL_ENET0_RGMII_RXD3_CONN_USDHC1_DATA3 0x00000021 + IMX8DXL_ENET0_RGMII_TXD0_CONN_USDHC1_VSELECT 0x00000021 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi new file mode 100644 index 000000000000..795d1d472fae --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi @@ -0,0 +1,52 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2019~2020, 2022 NXP + */ + +&audio_ipg_clk { + clock-frequency = <160000000>; +}; + +&dma_ipg_clk { + clock-frequency = <160000000>; +}; + +&i2c0 { + compatible = "fsl,imx8dxl-lpi2c", "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; + interrupts = <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>; +}; + +&i2c1 { + compatible = "fsl,imx8dxl-lpi2c", "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; + interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>; +}; + +&i2c2 { + compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; + interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>; +}; + +&i2c3 { + compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; + interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lpuart0 { + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; + interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lpuart1 { + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lpuart2 { + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; + interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lpuart3 { + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; + interrupts = <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi new file mode 100644 index 000000000000..69c4849f2132 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi @@ -0,0 +1,142 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2019~2020, 2022 NXP + */ + +/delete-node/ &enet1_lpcg; +/delete-node/ &fec2; + +&conn_subsys { + conn_enet0_root_clk: clock-conn-enet0-root { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <250000000>; + clock-output-names = "conn_enet0_root_clk"; + }; + + eqos: ethernet@5b050000 { + compatible = "nxp,imx8dxl-dwmac-eqos", "snps,dwmac-5.10a"; + reg = <0x5b050000 0x10000>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "eth_wake_irq", "macirq"; + clocks = <&eqos_lpcg IMX_LPCG_CLK_4>, + <&eqos_lpcg IMX_LPCG_CLK_6>, + <&eqos_lpcg IMX_LPCG_CLK_0>, + <&eqos_lpcg IMX_LPCG_CLK_5>, + <&eqos_lpcg IMX_LPCG_CLK_2>; + clock-names = "stmmaceth", "pclk", "ptp_ref", "tx", "mem"; + assigned-clocks = <&clk IMX_SC_R_ENET_1 IMX_SC_PM_CLK_PER>; + assigned-clock-rates = <125000000>; + power-domains = <&pd IMX_SC_R_ENET_1>; + status = "disabled"; + }; + + usbotg2: usb@5b0e0000 { + compatible = "fsl,imx8dxl-usb", "fsl,imx7ulp-usb"; + reg = <0x5b0e0000 0x200>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>; + fsl,usbphy = <&usbphy2>; + fsl,usbmisc = <&usbmisc2 0>; + /* + * usbotg1 and usbotg2 share one clcok. + * scu firmware disables the access to the clock and keeps + * it always on in case other core (M4) uses one of these. + */ + clocks = <&clk_dummy>; + ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; + rx-burst-size-dword = <0x10>; + #stream-id-cells = <1>; + power-domains = <&pd IMX_SC_R_USB_1>; + status = "disabled"; + + clk_dummy: clock-dummy { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <0>; + clock-output-names = "clk_dummy"; + }; + }; + + usbmisc2: usbmisc@5b0e0200 { + #index-cells = <1>; + compatible = "fsl,imx7ulp-usbmisc"; + reg = <0x5b0e0200 0x200>; + }; + + usbphy2: usbphy@0x5b110000 { + compatible = "fsl,imx8dxl-usbphy", "fsl,imx7ulp-usbphy"; + reg = <0x5b110000 0x1000>; + clocks = <&usb2_2_lpcg IMX_LPCG_CLK_7>; + power-domains = <&pd IMX_SC_R_USB_1_PHY>; + status = "disabled"; + }; + + eqos_lpcg: clock-controller@5b240000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5b240000 0x10000>; + #clock-cells = <1>; + clocks = <&conn_enet0_root_clk>, + <&conn_axi_clk>, + <&conn_axi_clk>, + <&clk IMX_SC_R_ENET_1 IMX_SC_PM_CLK_PER>, + <&conn_ipg_clk>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_2>, + <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>, + <IMX_LPCG_CLK_6>; + clock-output-names = "eqos_ptp", + "eqos_mem_clk", + "eqos_aclk", + "eqos_clk", + "eqos_csr_clk"; + power-domains = <&pd IMX_SC_R_ENET_1>; + }; + + usb2_2_lpcg: clock-controller@5b280000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5b280000 0x10000>; + #clock-cells = <1>; + clock-indices = <IMX_LPCG_CLK_7>; + clocks = <&conn_ipg_clk>; + clock-output-names = "usboh3_2_phy_ipg_clk"; + power-domains = <&pd IMX_SC_R_USB_1_PHY>; + }; + +}; + +&enet0_lpcg { + clocks = <&conn_enet0_root_clk>, + <&conn_enet0_root_clk>, + <&conn_axi_clk>, + <&clk IMX_SC_R_ENET_0 IMX_SC_C_TXCLK>, + <&conn_ipg_clk>, + <&conn_ipg_clk>; +}; + +&fec1 { + compatible = "fsl,imx8qm-fec"; + interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>; + assigned-clocks = <&clk IMX_SC_R_ENET_0 IMX_SC_C_CLKDIV>; + assigned-clock-rates = <125000000>; +}; + +&usdhc1 { + compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc"; + interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; +}; + +&usdhc2 { + compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc"; + interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>; +}; + +&usdhc3 { + compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc"; + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi new file mode 100644 index 000000000000..550f513708d8 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi @@ -0,0 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2020 NXP + */ + +&ddr_pmu0 { + compatible = "fsl,imx8-ddr-pmu"; + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi new file mode 100644 index 000000000000..815bd987b09b --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi @@ -0,0 +1,74 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2019~2020, 2022 NXP + */ + +&lsio_gpio0 { + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_gpio1 { + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; + interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_gpio2 { + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_gpio3 { + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_gpio4 { + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_gpio5 { + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_gpio6 { + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_gpio7 { + compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio"; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_mu0 { + compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_mu1 { + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_mu2 { + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; + interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_mu3 { + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_mu4 { + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; + interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; +}; + +&lsio_mu5 { + compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8dxl.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi new file mode 100644 index 000000000000..5ddbda0b4def --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi @@ -0,0 +1,238 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2019~2020, 2022 NXP + */ + +#include <dt-bindings/clock/imx8-clock.h> +#include <dt-bindings/firmware/imx/rsrc.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/pinctrl/pads-imx8dxl.h> +#include <dt-bindings/thermal/thermal.h> + +/ { + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + aliases { + ethernet0 = &fec1; + ethernet1 = &eqos; + gpio0 = &lsio_gpio0; + gpio1 = &lsio_gpio1; + gpio2 = &lsio_gpio2; + gpio3 = &lsio_gpio3; + gpio4 = &lsio_gpio4; + gpio5 = &lsio_gpio5; + gpio6 = &lsio_gpio6; + gpio7 = &lsio_gpio7; + mu1 = &lsio_mu1; + }; + + cpus: cpus { + #address-cells = <2>; + #size-cells = <0>; + + /* We have 1 clusters with 2 Cortex-A35 cores */ + A35_0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a35"; + reg = <0x0 0x0>; + enable-method = "psci"; + next-level-cache = <&A35_L2>; + clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>; + #cooling-cells = <2>; + operating-points-v2 = <&a35_opp_table>; + }; + + A35_1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a35"; + reg = <0x0 0x1>; + enable-method = "psci"; + next-level-cache = <&A35_L2>; + clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>; + #cooling-cells = <2>; + operating-points-v2 = <&a35_opp_table>; + }; + + A35_L2: l2-cache0 { + compatible = "cache"; + }; + }; + + a35_opp_table: opp-table { + compatible = "operating-points-v2"; + opp-shared; + + opp-900000000 { + opp-hz = /bits/ 64 <900000000>; + opp-microvolt = <1000000>; + clock-latency-ns = <150000>; + }; + + opp-1200000000 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt = <1100000>; + clock-latency-ns = <150000>; + opp-suspend; + }; + }; + + gic: interrupt-controller@51a00000 { + compatible = "arm,gic-v3"; + reg = <0x0 0x51a00000 0 0x10000>, /* GIC Dist */ + <0x0 0x51b00000 0 0xc0000>; /* GICR (RD_base + SGI_base) */ + #interrupt-cells = <3>; + interrupt-controller; + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + dsp_reserved: dsp@92400000 { + reg = <0 0x92400000 0 0x2000000>; + no-map; + }; + }; + + pmu { + compatible = "arm,armv8-pmuv3"; + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + system-controller { + compatible = "fsl,imx-scu"; + mbox-names = "tx0", + "rx0", + "gip3"; + mboxes = <&lsio_mu1 0 0 + &lsio_mu1 1 0 + &lsio_mu1 3 3>; + + pd: power-controller { + compatible = "fsl,scu-pd"; + #power-domain-cells = <1>; + wakeup-irq = <160 163 235 236 237 228 229 230 231 238 + 239 240 166 169>; + }; + + clk: clock-controller { + compatible = "fsl,imx8dxl-clk", "fsl,scu-clk"; + #clock-cells = <2>; + clocks = <&xtal32k &xtal24m>; + clock-names = "xtal_32KHz", "xtal_24Mhz"; + }; + + iomuxc: pinctrl { + compatible = "fsl,imx8dxl-iomuxc"; + }; + + ocotp: ocotp { + compatible = "fsl,imx8qxp-scu-ocotp"; + #address-cells = <1>; + #size-cells = <1>; + + fec_mac0: mac@2c4 { + reg = <0x2c4 6>; + }; + + fec_mac1: mac@2c6 { + reg = <0x2c6 6>; + }; + }; + + rtc: rtc { + compatible = "fsl,imx8qxp-sc-rtc"; + }; + + sc_pwrkey: keys { + compatible = "fsl,imx8qxp-sc-key", "fsl,imx-sc-key"; + linux,keycode = <KEY_POWER>; + wakeup-source; + }; + + watchdog { + compatible = "fsl,imx-sc-wdt"; + timeout-sec = <60>; + }; + + tsens: thermal-sensor { + compatible = "fsl,imx-sc-thermal"; + #thermal-sensor-cells = <1>; + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* Physical Secure */ + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* Physical Non-Secure */ + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* Virtual */ + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* Hypervisor */ + }; + + thermal_zones: thermal-zones { + cpu-thermal0 { + polling-delay-passive = <250>; + polling-delay = <2000>; + thermal-sensors = <&tsens IMX_SC_R_SYSTEM>; + + trips { + cpu_alert0: trip0 { + temperature = <107000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu_crit0: trip1 { + temperature = <127000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu_alert0>; + cooling-device = + <&A35_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&A35_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + }; + + /* The two values below cannot be changed by the board */ + xtal32k: clock-xtal32k { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "xtal_32KHz"; + }; + + xtal24m: clock-xtal24m { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24000000>; + clock-output-names = "xtal_24MHz"; + }; + + /* sorted in register address */ + #include "imx8-ss-adma.dtsi" + #include "imx8-ss-conn.dtsi" + #include "imx8-ss-ddr.dtsi" + #include "imx8-ss-lsio.dtsi" +}; + +#include "imx8dxl-ss-adma.dtsi" +#include "imx8dxl-ss-conn.dtsi" +#include "imx8dxl-ss-lsio.dtsi" +#include "imx8dxl-ss-ddr.dtsi" diff --git a/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm.dtsi index 9e6170d9394e..def7bb5d37cf 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm.dtsi @@ -2,7 +2,7 @@ /* * Copyright (c) 2018 NXP * Copyright (c) 2019 Engicam srl - * Copyright (c) 2020 Amarula Solutons(India) + * Copyright (c) 2020 Amarula Solutions(India) */ / { diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts new file mode 100644 index 000000000000..8b16bd68576c --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts @@ -0,0 +1,376 @@ +// SPDX-License-Identifier: GPL-2.0+ OR MIT +/* + * Copyright (C) 2022 Kontron Electronics GmbH + */ + +/dts-v1/; + +#include "imx8mm-kontron-osm-s.dtsi" + +/ { + model = "Kontron BL i.MX8MM OSM-S (N802X S)"; + compatible = "kontron,imx8mm-bl-osm-s", "kontron,imx8mm-osm-s", "fsl,imx8mm"; + + aliases { + ethernet1 = &usbnet; + }; + + /* fixed crystal dedicated to mcp2542fd */ + osc_can: clock-osc-can { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <40000000>; + clock-output-names = "osc-can"; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_led>; + + led1 { + label = "led1"; + gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + + led2 { + label = "led2"; + gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; + }; + + led3 { + label = "led3"; + gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; + }; + }; + + pwm-beeper { + compatible = "pwm-beeper"; + pwms = <&pwm2 0 5000 0>; + }; + + reg_rst_eth2: regulator-rst-eth2 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb_eth2>; + gpio = <&gpio3 2 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + regulator-name = "rst-usb-eth2"; + }; + + reg_usb1_vbus: regulator-usb1-vbus { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usb1_vbus>; + gpio = <&gpio3 25 GPIO_ACTIVE_LOW>; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-name = "usb1-vbus"; + }; + + reg_vdd_5v: regulator-5v { + compatible = "regulator-fixed"; + regulator-always-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-name = "vdd-5v"; + }; +}; + +&ecspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi2>; + cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>; + status = "okay"; + + can@0 { + compatible = "microchip,mcp251xfd"; + reg = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can>; + clocks = <&osc_can>; + interrupts-extended = <&gpio4 28 IRQ_TYPE_LEVEL_LOW>; + /* + * Limit the SPI clock to 15 MHz to prevent issues + * with corrupted data due to chip errata. + */ + spi-max-frequency = <15000000>; + vdd-supply = <®_vdd_3v3>; + xceiver-supply = <®_vdd_5v>; + }; +}; + +&ecspi3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi3>; + cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>; + status = "okay"; + + eeram@0 { + compatible = "microchip,48l640"; + reg = <0>; + spi-max-frequency = <20000000>; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-connection-type = "rgmii-rxid"; + phy-handle = <ðphy>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy: ethernet-phy@0 { + reg = <0>; + reset-assert-us = <1>; + reset-deassert-us = <15000>; + reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&gpio1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio1>; + gpio-line-names = "", "", "", "dio1-out", "", "", "dio1-in", "dio2-out", + "dio2-in", "dio3-out", "dio3-in", "dio4-out", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&gpio5 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio5>; + gpio-line-names = "", "", "dio4-in", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&i2c4 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + status = "okay"; +}; + +&pwm2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm2>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + uart-has-rtscts; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + linux,rs485-enabled-at-boot-time; + uart-has-rtscts; + status = "okay"; +}; + +&usbotg1 { + dr_mode = "otg"; + disable-over-current; + vbus-supply = <®_usb1_vbus>; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "host"; + disable-over-current; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + usb1@1 { + compatible = "usb424,9514"; + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + usbnet: ethernet@1 { + compatible = "usb424,ec00"; + reg = <1>; + local-mac-address = [ 00 00 00 00 00 00 ]; + }; + }; +}; + +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>; + vmmc-supply = <®_vdd_3v3>; + vqmmc-supply = <®_nvcc_sd>; + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&iomuxc { + pinctrl_can: cangrp { + fsl,pins = < + MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x19 + >; + }; + + pinctrl_ecspi2: ecspi2grp { + fsl,pins = < + MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x82 + MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x82 + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x82 + MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x19 + >; + }; + + pinctrl_ecspi3: ecspi3grp { + fsl,pins = < + MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO 0x82 + MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI 0x82 + MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK 0x82 + MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25 0x19 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3 + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3 + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f + MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x19 /* PHY RST */ + MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x19 /* ETH IRQ */ + >; + }; + + pinctrl_gpio_led: gpioledgrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x19 + MX8MM_IOMUXC_GPIO1_IO13_GPIO1_IO13 0x19 + MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x19 + >; + }; + + pinctrl_gpio1: gpio1grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x19 + MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19 + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19 + MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x19 + MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x19 + MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x19 + MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x19 + >; + }; + + pinctrl_gpio5: gpio5grp { + fsl,pins = < + MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2 0x19 + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x400001c3 + MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x400001c3 + >; + }; + + pinctrl_pwm2: pwm2grp { + fsl,pins = < + MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT 0x19 + >; + }; + + pinctrl_reg_usb1_vbus: regusb1vbusgrp { + fsl,pins = < + MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25 0x19 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX 0x140 + MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX 0x140 + MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B 0x140 + MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B 0x140 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x140 + MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x140 + MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x140 + MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x140 + >; + }; + + pinctrl_usb_eth2: usbeth2grp { + fsl,pins = < + MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2 0x19 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x019 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x019 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x019 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts index 23be1ec538ba..a079322a3793 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts @@ -5,11 +5,11 @@ /dts-v1/; -#include "imx8mm-kontron-n801x-som.dtsi" +#include "imx8mm-kontron-sl.dtsi" / { - model = "Kontron i.MX8MM N801X S"; - compatible = "kontron,imx8mm-n801x-s", "kontron,imx8mm-n801x-som", "fsl,imx8mm"; + model = "Kontron BL i.MX8MM (N801X S)"; + compatible = "kontron,imx8mm-bl", "kontron,imx8mm-sl", "fsl,imx8mm"; aliases { ethernet1 = &usbnet; @@ -321,6 +321,7 @@ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x019 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 >; }; @@ -333,6 +334,7 @@ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x019 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 >; }; @@ -345,6 +347,7 @@ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x019 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 >; }; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi new file mode 100644 index 000000000000..8d10f5b41297 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi @@ -0,0 +1,330 @@ +// SPDX-License-Identifier: GPL-2.0+ OR MIT +/* + * Copyright (C) 2022 Kontron Electronics GmbH + */ + +#include <dt-bindings/interrupt-controller/irq.h> +#include "imx8mm.dtsi" + +/ { + model = "Kontron OSM-S i.MX8MM (N802X SOM)"; + compatible = "kontron,imx8mm-osm-s", "fsl,imx8mm"; + + memory@40000000 { + device_type = "memory"; + /* + * There are multiple SoM flavors with different DDR sizes. + * The smallest is 1GB. For larger sizes the bootloader will + * update the reg property. + */ + reg = <0x0 0x40000000 0 0x80000000>; + }; + + chosen { + stdout-path = &uart3; + }; +}; + +&A53_0 { + cpu-supply = <®_vdd_arm>; +}; + +&A53_1 { + cpu-supply = <®_vdd_arm>; +}; + +&A53_2 { + cpu-supply = <®_vdd_arm>; +}; + +&A53_3 { + cpu-supply = <®_vdd_arm>; +}; + +&ddrc { + operating-points-v2 = <&ddrc_opp_table>; + + ddrc_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-100M { + opp-hz = /bits/ 64 <100000000>; + }; + + opp-750M { + opp-hz = /bits/ 64 <750000000>; + }; + }; +}; + +&ecspi1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; + status = "okay"; + + flash@0 { + compatible = "mxicy,mx25r1635f", "jedec,spi-nor"; + spi-max-frequency = <80000000>; + reg = <0>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x1e0000>; + }; + + partition@1e0000 { + label = "env"; + reg = <0x1e0000 0x10000>; + }; + + partition@1f0000 { + label = "env_redundant"; + reg = <0x1f0000 0x10000>; + }; + }; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pca9450: pmic@25 { + compatible = "nxp,pca9450a"; + reg = <0x25>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pmic>; + interrupt-parent = <&gpio1>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + + regulators { + reg_vdd_soc: BUCK1 { + regulator-name = "+0V8_VDD_SOC (BUCK1)"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <850000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <3125>; + nxp,dvs-run-voltage = <850000>; + nxp,dvs-standby-voltage = <800000>; + }; + + reg_vdd_arm: BUCK2 { + regulator-name = "+0V9_VDD_ARM (BUCK2)"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <950000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <3125>; + nxp,dvs-run-voltage = <950000>; + nxp,dvs-standby-voltage = <850000>; + }; + + reg_vdd_dram: BUCK3 { + regulator-name = "+0V9_VDD_DRAM&PU (BUCK3)"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <950000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_vdd_3v3: BUCK4 { + regulator-name = "+3V3 (BUCK4)"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_vdd_1v8: BUCK5 { + regulator-name = "+1V8 (BUCK5)"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_nvcc_dram: BUCK6 { + regulator-name = "+1V1_NVCC_DRAM (BUCK6)"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_nvcc_snvs: LDO1 { + regulator-name = "+1V8_NVCC_SNVS (LDO1)"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_vdd_snvs: LDO2 { + regulator-name = "+0V8_VDD_SNVS (LDO2)"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <900000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_vdda: LDO3 { + regulator-name = "+1V8_VDDA (LDO3)"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_vdd_phy: LDO4 { + regulator-name = "+0V9_VDD_PHY (LDO4)"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_nvcc_sd: LDO5 { + regulator-name = "NVCC_SD (LDO5)"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; + + rtc@52 { + compatible = "microcrystal,rv3028"; + reg = <0x52>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rtc>; + interrupts-extended = <&gpio4 1 IRQ_TYPE_LEVEL_HIGH>; + trickle-diode-disable; + }; +}; + +&uart3 { /* console */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + vmmc-supply = <®_vdd_3v3>; + vqmmc-supply = <®_vdd_1v8>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x82 + MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x82 + MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x82 + MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x19 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3 + >; + }; + + pinctrl_pmic: pmicgrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x141 + >; + }; + + pinctrl_rtc: rtcgrp { + fsl,pins = < + MX8MM_IOMUXC_SAI1_RXC_GPIO4_IO1 0x19 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140 + MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0 + MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d0 + MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d0 + MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d0 + MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d0 + MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x019 + MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x190 + >; + }; + + pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x194 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4 + MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d4 + MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d4 + MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d4 + MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d4 + MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x019 + MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x194 + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x196 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6 + MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d6 + MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d6 + MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d6 + MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d6 + MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x019 + MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x196 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi index 8f90eb02550d..0679728d2489 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi @@ -6,8 +6,8 @@ #include "imx8mm.dtsi" / { - model = "Kontron i.MX8MM N801X SoM"; - compatible = "kontron,imx8mm-n801x-som", "fsl,imx8mm"; + model = "Kontron SL i.MX8MM (N801X SOM)"; + compatible = "kontron,imx8mm-sl", "fsl,imx8mm"; memory@40000000 { device_type = "memory"; @@ -46,10 +46,6 @@ ddrc_opp_table: opp-table { compatible = "operating-points-v2"; - opp-25M { - opp-hz = /bits/ 64 <25000000>; - }; - opp-100M { opp-hz = /bits/ 64 <100000000>; }; @@ -70,6 +66,27 @@ compatible = "mxicy,mx25r1635f", "jedec,spi-nor"; spi-max-frequency = <80000000>; reg = <0>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x1e0000>; + }; + + partition@1e0000 { + label = "env"; + reg = <0x1e0000 0x10000>; + }; + + partition@1f0000 { + label = "env_redundant"; + reg = <0x1f0000 0x10000>; + }; + }; }; }; @@ -86,11 +103,10 @@ pinctrl-0 = <&pinctrl_pmic>; interrupt-parent = <&gpio1>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; - sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; regulators { reg_vdd_soc: BUCK1 { - regulator-name = "buck1"; + regulator-name = "+0V8_VDD_SOC (BUCK1)"; regulator-min-microvolt = <800000>; regulator-max-microvolt = <850000>; regulator-boot-on; @@ -101,7 +117,7 @@ }; reg_vdd_arm: BUCK2 { - regulator-name = "buck2"; + regulator-name = "+0V9_VDD_ARM (BUCK2)"; regulator-min-microvolt = <850000>; regulator-max-microvolt = <950000>; regulator-boot-on; @@ -112,7 +128,7 @@ }; reg_vdd_dram: BUCK3 { - regulator-name = "buck3"; + regulator-name = "+0V9_VDD_DRAM&PU (BUCK3)"; regulator-min-microvolt = <850000>; regulator-max-microvolt = <950000>; regulator-boot-on; @@ -120,7 +136,7 @@ }; reg_vdd_3v3: BUCK4 { - regulator-name = "buck4"; + regulator-name = "+3V3 (BUCK4)"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; regulator-boot-on; @@ -128,7 +144,7 @@ }; reg_vdd_1v8: BUCK5 { - regulator-name = "buck5"; + regulator-name = "+1V8 (BUCK5)"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-boot-on; @@ -136,7 +152,7 @@ }; reg_nvcc_dram: BUCK6 { - regulator-name = "buck6"; + regulator-name = "+1V1_NVCC_DRAM (BUCK6)"; regulator-min-microvolt = <1100000>; regulator-max-microvolt = <1100000>; regulator-boot-on; @@ -144,7 +160,7 @@ }; reg_nvcc_snvs: LDO1 { - regulator-name = "ldo1"; + regulator-name = "+1V8_NVCC_SNVS (LDO1)"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-boot-on; @@ -152,7 +168,7 @@ }; reg_vdd_snvs: LDO2 { - regulator-name = "ldo2"; + regulator-name = "+0V8_VDD_SNVS (LDO2)"; regulator-min-microvolt = <800000>; regulator-max-microvolt = <900000>; regulator-boot-on; @@ -160,7 +176,7 @@ }; reg_vdda: LDO3 { - regulator-name = "ldo3"; + regulator-name = "+1V8_VDDA (LDO3)"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-boot-on; @@ -168,7 +184,7 @@ }; reg_vdd_phy: LDO4 { - regulator-name = "ldo4"; + regulator-name = "+0V9_VDD_PHY (LDO4)"; regulator-min-microvolt = <900000>; regulator-max-microvolt = <900000>; regulator-boot-on; @@ -176,7 +192,7 @@ }; reg_nvcc_sd: LDO5 { - regulator-name = "ldo5"; + regulator-name = "NVCC_SD (LDO5)"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; }; @@ -229,7 +245,6 @@ pinctrl_pmic: pmicgrp { fsl,pins = < MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x141 - MX8MM_IOMUXC_GPIO1_IO04_GPIO1_IO4 0x141 >; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts index b1e7540f0281..641be3af989d 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts @@ -17,4 +17,3 @@ stdout-path = &uart2; }; }; - diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7902.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7902.dts index 6dc5eda2d256..31f4c735fe4f 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7902.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7902.dts @@ -222,7 +222,6 @@ compatible = "microchip,mcp2515"; reg = <0>; clocks = <&can20m>; - oscillator-frequency = <20000000>; interrupt-parent = <&gpio2>; interrupts = <3 IRQ_TYPE_LEVEL_LOW>; spi-max-frequency = <10000000>; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7903.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7903.dts index a65761a53f23..19f6d2943d26 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7903.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7903.dts @@ -250,7 +250,7 @@ }; &gpio2 { - gpio-line-names = "dig2_in", "dig2_out#", "", "", "", "", "", "", + gpio-line-names = "dig2_in", "dig2_out#", "dig2_ctl", "", "", "", "dig1_ctl", "", "dig1_out#", "dig1_in", "", "", "", "", "", "", "", "", "", "", "", "", "", "", "", "", "", "", "", "", "", ""; @@ -630,6 +630,8 @@ MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x40000041 /* RS232# */ MX8MM_IOMUXC_SD1_DATA7_GPIO2_IO9 0x40000041 /* DIG1_IN */ MX8MM_IOMUXC_SD1_DATA6_GPIO2_IO8 0x40000041 /* DIG1_OUT */ + MX8MM_IOMUXC_SD1_DATA4_GPIO2_IO6 0x40000041 /* DIG1_CTL */ + MX8MM_IOMUXC_SD1_DATA0_GPIO2_IO2 0x40000041 /* DIG2_CTL */ MX8MM_IOMUXC_SD1_CLK_GPIO2_IO0 0x40000041 /* DIG2_IN */ MX8MM_IOMUXC_SD1_CMD_GPIO2_IO1 0x40000041 /* DIG2_OUT */ MX8MM_IOMUXC_ECSPI1_MOSI_GPIO5_IO7 0x40000041 /* SIM1DET# */ diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7904.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7904.dts new file mode 100644 index 000000000000..a67771d02146 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7904.dts @@ -0,0 +1,888 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2022 Gateworks Corporation + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/linux-event-codes.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/phy/phy-imx8-pcie.h> + +#include "imx8mm.dtsi" + +/ { + model = "Gateworks Venice GW7904 i.MX8MM board"; + compatible = "gateworks,imx8mm-gw7904", "fsl,imx8mm"; + + chosen { + stdout-path = &uart2; + }; + + memory@40000000 { + device_type = "memory"; + reg = <0x0 0x40000000 0 0x80000000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + + key-0 { + label = "user_pb"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + linux,code = <BTN_0>; + }; + + key-1 { + label = "user_pb1x"; + linux,code = <BTN_1>; + interrupt-parent = <&gsc>; + interrupts = <0>; + }; + + key-2 { + label = "key_erased"; + linux,code = <BTN_2>; + interrupt-parent = <&gsc>; + interrupts = <1>; + }; + + key-3 { + label = "eeprom_wp"; + linux,code = <BTN_3>; + interrupt-parent = <&gsc>; + interrupts = <2>; + }; + + key-4 { + label = "switch_hold"; + linux,code = <BTN_5>; + interrupt-parent = <&gsc>; + interrupts = <7>; + }; + }; + + led-controller { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_leds>; + + led-0 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_GREEN>; + label = "led01_grn"; + gpios = <&gpioled 0 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led-1 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_YELLOW>; + label = "led01_yel"; + gpios = <&gpioled 1 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led-2 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_GREEN>; + label = "led02_grn"; + gpios = <&gpioled 2 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led-3 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_YELLOW>; + label = "led02_yel"; + gpios = <&gpioled 3 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led-4 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_GREEN>; + label = "led03_grn"; + gpios = <&gpioled 4 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led-5 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_YELLOW>; + label = "led03_yel"; + gpios = <&gpioled 5 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led-6 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_GREEN>; + label = "led04_grn"; + gpios = <&gpioled 6 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led-7 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_YELLOW>; + label = "led04_yel"; + gpios = <&gpioled 7 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led-8 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_GREEN>; + label = "led05_grn"; + gpios = <&gpioled 8 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led-9 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_YELLOW>; + label = "led05_yel"; + gpios = <&gpioled 9 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led-10 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_GREEN>; + label = "led06_grn"; + gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led-11 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_RED>; + label = "led06_red"; + gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led-12 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_GREEN>; + label = "led07_grn"; + gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led-13 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_RED>; + label = "led07_red"; + gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led-14 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_GREEN>; + label = "led08_grn"; + gpios = <&gpioled 10 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led-15 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_YELLOW>; + label = "led08_yel"; + gpios = <&gpioled 11 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led-16 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_GREEN>; + label = "led09_grn"; + gpios = <&gpioled 12 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led-17 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_YELLOW>; + label = "led09_yel"; + gpios = <&gpioled 13 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led-18 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_GREEN>; + label = "led10_grn"; + gpios = <&gpioled 14 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led-19 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_YELLOW>; + label = "led10_yel"; + gpios = <&gpioled 15 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + }; + + pcie0_refclk: pcie0-refclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <100000000>; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; +}; + +&A53_0 { + cpu-supply = <&buck2>; +}; + +&A53_1 { + cpu-supply = <&buck2>; +}; + +&A53_2 { + cpu-supply = <&buck2>; +}; + +&A53_3 { + cpu-supply = <&buck2>; +}; + +&ddrc { + operating-points-v2 = <&ddrc_opp_table>; + + ddrc_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-25M { + opp-hz = /bits/ 64 <25000000>; + }; + + opp-100M { + opp-hz = /bits/ 64 <100000000>; + }; + + opp-750M { + opp-hz = /bits/ 64 <750000000>; + }; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + local-mac-address = [00 00 00 00 00 00]; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + }; +}; + +&gpio1 { + gpio-line-names = "", "", "", "", "", "", "", "", + "", "", "", "", "rs232_en#", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&gpio5 { + gpio-line-names = "", "", "", "", "", "", "", "", + "", "", "", "", "pci_wdis#", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + gsc: gsc@20 { + compatible = "gw,gsc"; + reg = <0x20>; + pinctrl-0 = <&pinctrl_gsc>; + interrupt-parent = <&gpio4>; + interrupts = <26 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <1>; + + adc { + compatible = "gw,gsc-adc"; + #address-cells = <1>; + #size-cells = <0>; + + channel@6 { + gw,mode = <0>; + reg = <0x06>; + label = "temp"; + }; + + channel@82 { + gw,mode = <2>; + reg = <0x82>; + label = "vin"; + gw,voltage-divider-ohms = <22100 1000>; + gw,voltage-offset-microvolt = <700000>; + }; + + channel@84 { + gw,mode = <2>; + reg = <0x84>; + label = "vdd_5p0"; + gw,voltage-divider-ohms = <10000 10000>; + }; + + channel@86 { + gw,mode = <2>; + reg = <0x86>; + label = "vdd_3p3"; + gw,voltage-divider-ohms = <10000 10000>; + }; + + channel@88 { + gw,mode = <2>; + reg = <0x88>; + label = "vdd_0p9"; + }; + + channel@8c { + gw,mode = <2>; + reg = <0x8c>; + label = "vdd_soc"; + }; + + channel@8e { + gw,mode = <2>; + reg = <0x8e>; + label = "vdd_arm"; + }; + + channel@90 { + gw,mode = <2>; + reg = <0x90>; + label = "vdd_1p8"; + }; + + channel@92 { + gw,mode = <2>; + reg = <0x92>; + label = "vdd_dram"; + }; + + channel@a2 { + gw,mode = <2>; + reg = <0xa2>; + label = "vdd_gsc"; + gw,voltage-divider-ohms = <10000 10000>; + }; + }; + }; + + gpio: gpio@23 { + compatible = "nxp,pca9555"; + reg = <0x23>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&gsc>; + interrupts = <4>; + }; + + eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + pagesize = <16>; + }; + + eeprom@51 { + compatible = "atmel,24c02"; + reg = <0x51>; + pagesize = <16>; + }; + + eeprom@52 { + compatible = "atmel,24c02"; + reg = <0x52>; + pagesize = <16>; + }; + + eeprom@53 { + compatible = "atmel,24c02"; + reg = <0x53>; + pagesize = <16>; + }; + + rtc@68 { + compatible = "dallas,ds1672"; + reg = <0x68>; + }; +}; + +&i2c2 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + pmic@4b { + compatible = "rohm,bd71847"; + reg = <0x4b>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pmic>; + interrupt-parent = <&gpio3>; + interrupts = <8 IRQ_TYPE_LEVEL_LOW>; + rohm,reset-snvs-powered; + #clock-cells = <0>; + clocks = <&osc_32k 0>; + clock-output-names = "clk-32k-out"; + + regulators { + /* vdd_soc: 0.805-0.900V (typ=0.8V) */ + BUCK1 { + regulator-name = "buck1"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + }; + + /* vdd_arm: 0.805-1.0V (typ=0.9V) */ + buck2: BUCK2 { + regulator-name = "buck2"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + rohm,dvs-run-voltage = <1000000>; + rohm,dvs-idle-voltage = <900000>; + }; + + /* vdd_0p9: 0.805-1.0V (typ=0.9V) */ + BUCK3 { + regulator-name = "buck3"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1350000>; + regulator-boot-on; + regulator-always-on; + }; + + /* vdd_3p3 */ + BUCK4 { + regulator-name = "buck4"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + /* vdd_1p8 */ + BUCK5 { + regulator-name = "buck5"; + regulator-min-microvolt = <1605000>; + regulator-max-microvolt = <1995000>; + regulator-boot-on; + regulator-always-on; + }; + + /* vdd_dram */ + BUCK6 { + regulator-name = "buck6"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + }; + + /* nvcc_snvs_1p8 */ + LDO1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <1600000>; + regulator-max-microvolt = <1900000>; + regulator-boot-on; + regulator-always-on; + }; + + /* vdd_snvs_0p8 */ + LDO2 { + regulator-name = "ldo2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <900000>; + regulator-boot-on; + regulator-always-on; + }; + + /* vdda_1p8 */ + LDO3 { + regulator-name = "ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + LDO4 { + regulator-name = "ldo4"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + LDO6 { + regulator-name = "ldo6"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; + +&i2c3 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + accelerometer@19 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_accel>; + compatible = "st,lis2de12"; + reg = <0x19>; + st,drdy-int-pin = <1>; + interrupt-parent = <&gpio1>; + interrupts = <15 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "INT1"; + }; +}; + +&i2c4 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + status = "okay"; + + gpioled: gpio@27 { + compatible = "nxp,pca9555"; + reg = <0x27>; + gpio-controller; + #gpio-cells = <2>; + }; +}; + +&pcie_phy { + fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>; + fsl,clkreq-unsupported; + clocks = <&pcie0_refclk>; + clock-names = "ref"; + status = "okay"; +}; + +&pcie0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcie0>; + reset-gpio = <&gpio5 11 GPIO_ACTIVE_LOW>; + clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>, + <&pcie0_refclk>; + clock-names = "pcie", "pcie_aux", "pcie_bus"; + assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>, + <&clk IMX8MM_CLK_PCIE1_CTRL>; + assigned-clock-rates = <10000000>, <250000000>; + assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>, + <&clk IMX8MM_SYS_PLL2_250M>; + status = "okay"; +}; + +&pgc_mipi { + status = "disabled"; +}; + +/* off-board RS232 */ +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +/* console */ +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +/* off-board RS232 */ +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&usbotg1 { + dr_mode = "host"; + disable-over-current; + status = "okay"; +}; + +/* microSD */ +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + bus-width = <4>; + vmmc-supply = <®_3p3v>; + status = "okay"; +}; + +/* eMMC */ +&usdhc3 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_hog: hoggrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x40000041 /* RS232# */ + MX8MM_IOMUXC_ECSPI2_MISO_GPIO5_IO12 0x40000041 /* PCI_WDIS# */ + >; + }; + + pinctrl_accel: accelgrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x159 + >; + }; + + pinctrl_fec1: fec1grp { + fsl,pins = < + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3 + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3 + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f + MX8MM_IOMUXC_SAI2_TXFS_GPIO4_IO24 0x19 /* IRQ# */ + MX8MM_IOMUXC_SAI2_TXC_GPIO4_IO25 0x19 /* RST# */ + >; + }; + + pinctrl_gpio_leds: gpioledsgrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x40000019 + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x40000019 + MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x40000019 + MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x40000019 + >; + }; + + pinctrl_gsc: gscgrp { + fsl,pins = < + MX8MM_IOMUXC_SAI2_TXD0_GPIO4_IO26 0x159 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3 + MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x400001c3 + MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x400001c3 + >; + }; + + pinctrl_pcie0: pciegrp { + fsl,pins = < + MX8MM_IOMUXC_ECSPI2_MOSI_GPIO5_IO11 0x41 + >; + }; + + pinctrl_pmic: pmicgrp { + fsl,pins = < + MX8MM_IOMUXC_NAND_DATA02_GPIO3_IO8 0x41 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140 + MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140 + MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140 + MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 + >; + }; + + pinctrl_usdhc2_gpio: usdhc2-gpiogrp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x1c4 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190 + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi index 3ec0c9ac3170..bcab830c6e95 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi @@ -53,6 +53,21 @@ }; }; + hdmi_connector: hdmi-connector { + compatible = "hdmi-connector"; + ddc-i2c-bus = <&i2c2>; + label = "hdmi"; + type = "a"; + status = "disabled"; + }; + + panel_lvds: panel-lvds { + compatible = "panel-lvds"; + backlight = <&backlight>; + data-mapping = "vesa-24"; + status = "disabled"; + }; + /* Carrier Board Supplies */ reg_1p8v: regulator-1p8v { compatible = "regulator-fixed"; @@ -561,8 +576,8 @@ status = "disabled"; }; - lvds_ti_sn65dsi83: bridge@2c { - compatible = "ti,sn65dsi83"; + lvds_ti_sn65dsi84: bridge@2c { + compatible = "ti,sn65dsi84"; /* Verdin GPIO_9_DSI (SN65DSI84 IRQ, SODIMM 17, unused) */ /* Verdin GPIO_10_DSI (SODIMM 21) */ enable-gpios = <&gpio3 3 GPIO_ACTIVE_HIGH>; diff --git a/arch/arm64/boot/dts/freescale/imx8mn-venice-gw7902.dts b/arch/arm64/boot/dts/freescale/imx8mn-venice-gw7902.dts index 636f8602b979..dd4302ac1de4 100644 --- a/arch/arm64/boot/dts/freescale/imx8mn-venice-gw7902.dts +++ b/arch/arm64/boot/dts/freescale/imx8mn-venice-gw7902.dts @@ -213,7 +213,6 @@ compatible = "microchip,mcp2515"; reg = <0>; clocks = <&can20m>; - oscillator-frequency = <20000000>; interrupt-parent = <&gpio2>; interrupts = <3 IRQ_TYPE_LEVEL_LOW>; spi-max-frequency = <10000000>; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-dhcom-pdk2.dts b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-pdk2.dts index 2ca2ede2e94e..382fbedaf6ba 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp-dhcom-pdk2.dts +++ b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-pdk2.dts @@ -1,18 +1,23 @@ // SPDX-License-Identifier: (GPL-2.0+ OR MIT) /* * Copyright (C) 2022 Marek Vasut <marex@denx.de> + * + * DHCOM iMX8MP variant: + * DHCM-iMX8ML8-C160-R409-F1638-SPI16-GE-CAN2-SD-RTC-WBTA-ADC-T-RGB-CSI2-HS-I-01D2 + * DHCOM PCB number: 660-100 or newer + * PDK2 PCB number: 516-400 or newer */ /dts-v1/; #include <dt-bindings/leds/common.h> -#include <dt-bindings/net/qca-ar803x.h> #include <dt-bindings/phy/phy-imx8-pcie.h> #include "imx8mp-dhcom-som.dtsi" / { model = "DH electronics i.MX8M Plus DHCOM Premium Developer Kit (2)"; - compatible = "dh,imx8mp-dhcom-pdk2", "fsl,imx8mp"; + compatible = "dh,imx8mp-dhcom-pdk2", "dh,imx8mp-dhcom-som", + "fsl,imx8mp"; chosen { stdout-path = &uart1; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts index f6b017ab5f53..9f1469db554d 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts +++ b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts @@ -5,6 +5,7 @@ /dts-v1/; +#include <dt-bindings/phy/phy-imx8-pcie.h> #include "imx8mp.dtsi" / { @@ -33,6 +34,12 @@ <0x1 0x00000000 0 0xc0000000>; }; + pcie0_refclk: pcie0-refclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <100000000>; + }; + reg_can1_stby: regulator-can1-stby { compatible = "regulator-fixed"; regulator-name = "can1-stby"; @@ -55,6 +62,17 @@ enable-active-high; }; + reg_pcie0: regulator-pcie { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcie0_reg>; + regulator-name = "MPCIE_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 6 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + reg_usdhc2_vmmc: regulator-usdhc2 { compatible = "regulator-fixed"; pinctrl-names = "default"; @@ -350,6 +368,28 @@ */ }; +&pcie_phy { + fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>; + clocks = <&pcie0_refclk>; + clock-names = "ref"; + status = "okay"; +}; + +&pcie { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcie0>; + reset-gpio = <&gpio2 7 GPIO_ACTIVE_LOW>; + clocks = <&clk IMX8MP_CLK_HSIO_ROOT>, + <&clk IMX8MP_CLK_PCIE_ROOT>, + <&clk IMX8MP_CLK_HSIO_AXI>; + clock-names = "pcie", "pcie_aux", "pcie_bus"; + assigned-clocks = <&clk IMX8MP_CLK_PCIE_AUX>; + assigned-clock-rates = <10000000>; + assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_50M>; + vpcie-supply = <®_pcie0>; + status = "okay"; +}; + &snvs_pwrkey { status = "okay"; }; @@ -502,6 +542,19 @@ >; }; + pinctrl_pcie0: pcie0grp { + fsl,pins = < + MX8MP_IOMUXC_I2C4_SCL__PCIE_CLKREQ_B 0x61 /* open drain, pull up */ + MX8MP_IOMUXC_SD1_DATA5__GPIO2_IO07 0x41 + >; + }; + + pinctrl_pcie0_reg: pcie0reggrp { + fsl,pins = < + MX8MP_IOMUXC_SD1_DATA4__GPIO2_IO06 0x41 + >; + }; + pinctrl_pmic: pmicgrp { fsl,pins = < MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03 0x000001c0 diff --git a/arch/arm64/boot/dts/freescale/imx8mp-icore-mx8mp-edimm2.2.dts b/arch/arm64/boot/dts/freescale/imx8mp-icore-mx8mp-edimm2.2.dts index dd703b6a5e17..a02b31c42db4 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp-icore-mx8mp-edimm2.2.dts +++ b/arch/arm64/boot/dts/freescale/imx8mp-icore-mx8mp-edimm2.2.dts @@ -2,7 +2,7 @@ /* * Copyright (c) 2018 NXP * Copyright (c) 2019 Engicam srl - * Copyright (c) 2020 Amarula Solutons(India) + * Copyright (c) 2020 Amarula Solutions(India) */ /dts-v1/; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-icore-mx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-icore-mx8mp.dtsi index 5116079cce22..a6319824ea2e 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp-icore-mx8mp.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mp-icore-mx8mp.dtsi @@ -2,7 +2,7 @@ /* * Copyright (c) 2018 NXP * Copyright (c) 2019 Engicam srl - * Copyright (c) 2020 Amarula Solutons(India) + * Copyright (c) 2020 Amarula Solutions(India) */ / { diff --git a/arch/arm64/boot/dts/freescale/imx8mp-msc-sm2s-14N0600E.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-msc-sm2s-14N0600E.dtsi new file mode 100644 index 000000000000..2f5cc013e8d6 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-msc-sm2s-14N0600E.dtsi @@ -0,0 +1,68 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2022 Avnet Embedded GmbH + */ +/dts-v1/; + +#include "imx8mp-msc-sm2s.dtsi" + +/ { + memory@40000000 { + device_type = "memory"; + reg = <0x0 0x40000000 0 0x80000000>; /* bank0, 2GiB */ + }; +}; + +&cpu_alert0 { + temperature = <95000>; +}; + +&cpu_crit0 { + temperature = <105000>; +}; + +&soc_alert0 { + temperature = <95000>; +}; + +&soc_crit0 { + temperature = <105000>; +}; + +&tca6424 { + gbe0-int-hog { + gpio-hog; + input; + gpios = <3 GPIO_ACTIVE_LOW>; + }; + + gbe1-int-hog { + gpio-hog; + input; + gpios = <4 GPIO_ACTIVE_LOW>; + }; + + cam2-rst-hog { + gpio-hog; + output-high; + gpios = <9 GPIO_ACTIVE_LOW>; + }; + + cam2-pwr-hog { + gpio-hog; + output-high; + gpios = <10 GPIO_ACTIVE_LOW>; + }; + + tpm-int-hog { + gpio-hog; + input; + gpios = <13 GPIO_ACTIVE_LOW>; + }; + + wifi-int-hog { + gpio-hog; + input; + gpios = <14 GPIO_ACTIVE_LOW>; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-msc-sm2s-ep1.dts b/arch/arm64/boot/dts/freescale/imx8mp-msc-sm2s-ep1.dts new file mode 100644 index 000000000000..470ff8e31e32 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-msc-sm2s-ep1.dts @@ -0,0 +1,52 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2022 Avnet Embedded GmbH + */ + +/dts-v1/; + +#include "imx8mp-msc-sm2s-14N0600E.dtsi" +#include <dt-bindings/clock/imx8mp-clock.h> +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "MSC SM2-MB-EP1 Carrier Board with SM2S-IMX8PLUS-QC6-14N0600E SoM"; + compatible = "avnet,sm2s-imx8mp-14N0600E-ep1", + "avnet,sm2s-imx8mp-14N0600E", "avnet,sm2s-imx8mp", + "fsl,imx8mp"; +}; + +&flexcan1 { + status = "okay"; +}; + +&flexcan2 { + status = "okay"; +}; + +&usdhc2 { + no-1-8-v; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_smarc_gpio>; + + pinctrl_smarc_gpio: smarcgpiosgrp { + fsl,pins = + <MX8MP_IOMUXC_GPIO1_IO11__GPIO1_IO11 0x19>, /* GPIO0 */ + <MX8MP_IOMUXC_SAI1_RXC__GPIO4_IO01 0x19>, /* GPIO1 */ + <MX8MP_IOMUXC_SAI1_RXD0__GPIO4_IO02 0x19>, /* GPIO2 */ + <MX8MP_IOMUXC_SAI1_RXD1__GPIO4_IO03 0x19>, /* GPIO3 */ + <MX8MP_IOMUXC_SAI3_RXC__GPIO4_IO29 0x19>, /* GPIO4 */ + <MX8MP_IOMUXC_SAI3_MCLK__GPIO5_IO02 0x19>, /* GPIO5 */ + <MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18 0x19>, /* GPIO6 */ + <MX8MP_IOMUXC_GPIO1_IO10__GPIO1_IO10 0x19>, /* GPIO7 */ + <MX8MP_IOMUXC_SAI1_MCLK__GPIO4_IO20 0x19>, /* GPIO8 */ + <MX8MP_IOMUXC_SAI2_RXFS__GPIO4_IO21 0x19>, /* GPIO9 */ + <MX8MP_IOMUXC_SAI2_RXC__GPIO4_IO22 0x19>, /* GPIO10 */ + <MX8MP_IOMUXC_SAI3_RXFS__GPIO4_IO28 0x19>, /* GPIO11 */ + <MX8MP_IOMUXC_SAI1_TXD7__GPIO4_IO19 0x19>, /* GPIO12 */ + <MX8MP_IOMUXC_SAI1_RXFS__GPIO4_IO00 0x19>; /* GPIO13 */ + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-msc-sm2s.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-msc-sm2s.dtsi new file mode 100644 index 000000000000..5dbec71747c3 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-msc-sm2s.dtsi @@ -0,0 +1,820 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2022 Avnet Embedded GmbH + */ + +/dts-v1/; + +#include "imx8mp.dtsi" +#include <dt-bindings/net/ti-dp83867.h> + +/ { + aliases { + rtc0 = &sys_rtc; + rtc1 = &snvs_rtc; + }; + + chosen { + stdout-path = &uart2; + }; + + reg_usb0_host_vbus: regulator-usb0-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb0_host_vbus"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb0_vbus>; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usb1_host_vbus: regulator-usb1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1_host_vbus"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb1_vbus>; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usdhc2_vmmc: regulator-usdhc2 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2_vmmc>; + regulator-name = "VSD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; + enable-active-high; + startup-delay-us = <100>; + off-on-delay-us = <12000>; + }; + + reg_flexcan1_xceiver: regulator-flexcan1 { + compatible = "regulator-fixed"; + regulator-name = "flexcan1-xceiver"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + reg_flexcan2_xceiver: regulator-flexcan2 { + compatible = "regulator-fixed"; + regulator-name = "flexcan2-xceiver"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + lcd0_backlight: backlight-0 { + compatible = "pwm-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd0_backlight>; + pwms = <&pwm1 0 100000 0>; + brightness-levels = <0 255>; + num-interpolated-steps = <255>; + default-brightness-level = <255>; + enable-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; + status = "disabled"; + }; + + lcd1_backlight: backlight-1 { + compatible = "pwm-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd1_backlight>; + pwms = <&pwm2 0 100000 0>; + brightness-levels = <0 255>; + num-interpolated-steps = <255>; + default-brightness-level = <255>; + enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; + status = "disabled"; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds>; + status = "okay"; + + led-sw { + label = "sw-led"; + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + default-state = "off"; + linux,default-trigger = "heartbeat"; + }; + }; + + extcon_usb0: extcon-usb0 { + compatible = "linux,extcon-usb-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb0_extcon>; + id-gpio = <&gpio1 3 GPIO_ACTIVE_HIGH>; + }; +}; + +&A53_0 { + cpu-supply = <&vcc_arm>; +}; + +&A53_1 { + cpu-supply = <&vcc_arm>; +}; + +&A53_2 { + cpu-supply = <&vcc_arm>; +}; + +&A53_3 { + cpu-supply = <&vcc_arm>; +}; + +&ecspi1 { + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + cs-gpios = <0>, <&gpio2 8 GPIO_ACTIVE_LOW>; +}; + +&ecspi2 { + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi2>; + cs-gpios = <0>, <&gpio2 9 GPIO_ACTIVE_LOW>; +}; + +&eqos { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_eqos>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + status = "okay"; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + eee-broken-1000t; + reset-gpios = <&tca6424 16 GPIO_ACTIVE_LOW>; + reset-assert-us = <1000>; + reset-deassert-us = <1000>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>; + }; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy1>; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + eee-broken-1000t; + reset-gpios = <&tca6424 17 GPIO_ACTIVE_LOW>; + reset-assert-us = <1000>; + reset-deassert-us = <1000>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>; + }; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + clock-frequency = <400000>; + status = "okay"; + + id_eeprom: eeprom@50 { + compatible = "atmel,24c64"; + reg = <0x50>; + pagesize = <32>; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + clock-frequency = <400000>; + status = "disabled"; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + clock-frequency = <400000>; + status = "disabled"; +}; + +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + clock-frequency = <400000>; + status = "disabled"; +}; + +&i2c5 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c5>; + clock-frequency = <400000>; + status = "disabled"; +}; + +&i2c6 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c6>; + clock-frequency = <400000>; + status = "okay"; + + tca6424: gpio@22 { + compatible = "ti,tca6424"; + reg = <0x22>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tca6424>; + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = "BOOT_SEL0#", "BOOT_SEL1#", "BOOT_SEL2#", + "gbe0_int", "gbe1_int", "pmic_int", "rtc_int", "lvds_int", + "PCIE_WAKE#", "cam2_rst", "cam2_pwr", "SLEEP#", + "wifi_pd", "tpm_int", "wifi_int", "PCIE_A_RST#", + "gbe0_rst", "gbe1_rst", "LID#", "BATLOW#", "CHARGING#", + "CHARGER_PRSNT#"; + interrupt-parent = <&gpio1>; + interrupts = <9 IRQ_TYPE_EDGE_RISING>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + dsi_lvds_bridge: bridge@2d { + compatible = "ti,sn65dsi83"; + reg = <0x2d>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lvds_bridge>; + enable-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; + status = "disabled"; + }; + + pmic: pmic@30 { + compatible = "ricoh,rn5t567"; + reg = <0x30>; + interrupt-parent = <&tca6424>; + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; + + regulators { + DCDC1 { + regulator-name = "VCC_SOC"; + regulator-always-on; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <950000>; + }; + + DCDC2 { + regulator-name = "VCC_DRAM"; + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + }; + + vcc_arm: DCDC3 { + regulator-name = "VCC_ARM"; + regulator-always-on; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <950000>; + }; + + DCDC4 { + regulator-name = "VCC_1V8"; + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + LDO1 { + regulator-name = "VCC_LDO1_2V5"; + regulator-always-on; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + }; + + LDO2 { + regulator-name = "VCC_LDO2_1V8"; + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + LDO3 { + regulator-name = "VCC_ETH_2V5"; + regulator-always-on; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + }; + + LDO4 { + regulator-name = "VCC_DDR4_2V5"; + regulator-always-on; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + }; + + LDO5 { + regulator-name = "VCC_LDO5_1V8"; + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + LDORTC1 { + regulator-name = "VCC_SNVS_1V8"; + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + LDORTC2 { + regulator-name = "VCC_SNVS_3V3"; + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; + + sys_rtc: rtc@32 { + compatible = "ricoh,r2221tl"; + reg = <0x32>; + interrupt-parent = <&tca6424>; + interrupts = <6 IRQ_TYPE_EDGE_FALLING>; + }; + + tmp_sensor: temperature-sensor@71 { + compatible = "ti,tmp103"; + reg = <0x71>; + }; +}; + +&flexcan1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1>; + xceiver-supply = <®_flexcan1_xceiver>; + status = "disabled"; +}; + +&flexcan2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan2>; + xceiver-supply = <®_flexcan2_xceiver>; + status = "disabled"; +}; + +&flexspi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexspi0>; + status = "okay"; + + qspi_flash: flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <80000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + }; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; + status = "disabled"; +}; + +&pwm2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm2>; + status = "disabled"; +}; + +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm3>; + status = "disabled"; +}; + +&pwm4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm4>; + status = "disabled"; +}; + +&snvs_pwrkey { + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + uart-has-rtscts; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + uart-has-rtscts; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "disabled"; +}; + +&usb3_phy0 { + vbus-supply = <®_usb0_host_vbus>; + status = "okay"; +}; + +&usb3_phy1 { + vbus-supply = <®_usb1_host_vbus>; + status = "okay"; +}; + +&usb3_0 { + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; + +&usb_dwc3_0 { + dr_mode = "otg"; + hnp-disable; + srp-disable; + adp-disable; + extcon = <&extcon_usb0>; + status = "okay"; +}; + +&usb_dwc3_1 { + dr_mode = "host"; + status = "okay"; +}; + +&usdhc2 { + assigned-clocks = <&clk IMX8MP_CLK_USDHC2>; + assigned-clock-rates = <400000000>; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>; + bus-width = <4>; + vmmc-supply = <®_usdhc2_vmmc>; + status = "okay"; +}; + +&usdhc3 { + assigned-clocks = <&clk IMX8MP_CLK_USDHC3>; + assigned-clock-rates = <400000000>; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl_ecspi1: ecspi1grp { + fsl,pins = + <MX8MP_IOMUXC_ECSPI1_MISO__ECSPI1_MISO 0x82>, + <MX8MP_IOMUXC_ECSPI1_MOSI__ECSPI1_MOSI 0x82>, + <MX8MP_IOMUXC_ECSPI1_SCLK__ECSPI1_SCLK 0x82>, + <MX8MP_IOMUXC_ECSPI1_SS0__ECSPI1_SS0 0x40000>, + <MX8MP_IOMUXC_SD1_DATA6__GPIO2_IO08 0x40000>; + }; + + pinctrl_ecspi2: ecspi2grp { + fsl,pins = + <MX8MP_IOMUXC_ECSPI2_MISO__ECSPI2_MISO 0x82>, + <MX8MP_IOMUXC_ECSPI2_MOSI__ECSPI2_MOSI 0x82>, + <MX8MP_IOMUXC_ECSPI2_SCLK__ECSPI2_SCLK 0x82>, + <MX8MP_IOMUXC_ECSPI2_SS0__ECSPI2_SS0 0x40000>, + <MX8MP_IOMUXC_SD1_DATA7__GPIO2_IO09 0x40000>; + }; + + pinctrl_eqos: eqosgrp { + fsl,pins = + <MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC 0x3>, + <MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO 0x3>, + <MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0 0x91>, + <MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1 0x91>, + <MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2 0x91>, + <MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3 0x91>, + <MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x91>, + <MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x91>, + <MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0 0x1f>, + <MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1 0x1f>, + <MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2 0x1f>, + <MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3 0x1f>, + <MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x1f>, + <MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x1f>; + }; + + pinctrl_fec: fecgrp { + fsl,pins = + <MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC 0x3>, + <MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO 0x3>, + <MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0 0x91>, + <MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1 0x91>, + <MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2 0x91>, + <MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3 0x91>, + <MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC 0x91>, + <MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL 0x91>, + <MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0 0x1f>, + <MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1 0x1f>, + <MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2 0x1f>, + <MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3 0x1f>, + <MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL 0x1f>, + <MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC 0x1f>; + }; + + pinctrl_flexcan1: flexcan1grp { + fsl,pins = + <MX8MP_IOMUXC_SAI5_RXD1__CAN1_TX 0x154>, + <MX8MP_IOMUXC_SAI5_RXD2__CAN1_RX 0x154>; + }; + + pinctrl_flexcan2: flexcan2grp { + fsl,pins = + <MX8MP_IOMUXC_SAI5_MCLK__CAN2_RX 0x154>, + <MX8MP_IOMUXC_SAI5_RXD3__CAN2_TX 0x154>; + }; + + pinctrl_flexspi0: flexspi0grp { + fsl,pins = + <MX8MP_IOMUXC_NAND_ALE__FLEXSPI_A_SCLK 0x1c2>, + <MX8MP_IOMUXC_NAND_CE0_B__FLEXSPI_A_SS0_B 0x82>, + <MX8MP_IOMUXC_NAND_DATA00__FLEXSPI_A_DATA00 0x82>, + <MX8MP_IOMUXC_NAND_DATA01__FLEXSPI_A_DATA01 0x82>, + <MX8MP_IOMUXC_NAND_DATA02__FLEXSPI_A_DATA02 0x82>, + <MX8MP_IOMUXC_NAND_DATA03__FLEXSPI_A_DATA03 0x82>, + <MX8MP_IOMUXC_NAND_DQS__GPIO3_IO14 0x19>; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = + <MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c3>, + <MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA 0x400001c3>; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = + <MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL 0x400001c3>, + <MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA 0x400001c3>; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = + <MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL 0x400001c3>, + <MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA 0x400001c3>; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = + <MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL 0x400001c3>, + <MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA 0x400001c3>; + }; + + pinctrl_i2c5: i2c5grp { + fsl,pins = + <MX8MP_IOMUXC_SPDIF_TX__I2C5_SCL 0x400001c3>, + <MX8MP_IOMUXC_SPDIF_RX__I2C5_SDA 0x400001c3>; + }; + + pinctrl_i2c6: i2c6grp { + fsl,pins = + <MX8MP_IOMUXC_SAI5_RXFS__I2C6_SCL 0x400001c3>, + <MX8MP_IOMUXC_SAI5_RXC__I2C6_SDA 0x400001c3>; + }; + + pinctrl_lcd0_backlight: lcd0-backlightgrp { + fsl,pins = + <MX8MP_IOMUXC_GPIO1_IO05__GPIO1_IO05 0x41>; + }; + + pinctrl_lcd1_backlight: lcd1-backlightgrp { + fsl,pins = + <MX8MP_IOMUXC_GPIO1_IO06__GPIO1_IO06 0x41>; + }; + + pinctrl_leds: ledsgrp { + fsl,pins = + <MX8MP_IOMUXC_GPIO1_IO08__GPIO1_IO08 0x19>; + }; + + pinctrl_lvds_bridge: lvds-bridgegrp { + fsl,pins = + <MX8MP_IOMUXC_GPIO1_IO07__GPIO1_IO07 0x41>; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = + <MX8MP_IOMUXC_SPDIF_EXT_CLK__PWM1_OUT 0x116>; + }; + + pinctrl_pwm2: pwm2grp { + fsl,pins = + <MX8MP_IOMUXC_SAI5_RXD0__PWM2_OUT 0x116>; + }; + + pinctrl_pwm3: pwm3grp { + fsl,pins = + <MX8MP_IOMUXC_GPIO1_IO10__PWM3_OUT 0x116>; + }; + + pinctrl_pwm4: pwm4grp { + fsl,pins = + <MX8MP_IOMUXC_SAI3_MCLK__PWM4_OUT 0x116>; + }; + + pinctrl_tca6424: tca6424grp { + fsl,pins = + <MX8MP_IOMUXC_GPIO1_IO09__GPIO1_IO09 0x41>; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = + <MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX 0x49>, + <MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX 0x49>; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = + <MX8MP_IOMUXC_SD1_DATA4__GPIO2_IO06 0x1c4>, + <MX8MP_IOMUXC_SD1_DATA5__GPIO2_IO07 0x1c4>, + <MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX 0x49>, + <MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX 0x49>; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = + <MX8MP_IOMUXC_SD1_RESET_B__GPIO2_IO10 0x1c4>, + <MX8MP_IOMUXC_SD1_STROBE__GPIO2_IO11 0x1c4>, + <MX8MP_IOMUXC_UART3_RXD__UART3_DCE_RX 0x49>, + <MX8MP_IOMUXC_UART3_TXD__UART3_DCE_TX 0x49>; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = + <MX8MP_IOMUXC_UART4_RXD__UART4_DCE_RX 0x49>, + <MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX 0x49>; + }; + + pinctrl_usb0_extcon: usb0-extcongrp { + fsl,pins = + <MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03 0x19>; + }; + + pinctrl_usb0_vbus: usb0-vbusgrp { + fsl,pins = + <MX8MP_IOMUXC_GPIO1_IO12__GPIO1_IO12 0x19>; + }; + + pinctrl_usb1_vbus: usb1-vbusgrp { + fsl,pins = + <MX8MP_IOMUXC_GPIO1_IO14__GPIO1_IO14 0x19>; + }; + + pinctrl_usdhc2_gpio: usdhc2-gpiogrp { + fsl,pins = + <MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12 0x1c4>, + <MX8MP_IOMUXC_SD2_WP__GPIO2_IO20 0x1c4>; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = + <MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x190>, + <MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d0>, + <MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d0>, + <MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d0>, + <MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d0>, + <MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d0>, + <MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1>; + }; + + pinctrl_usdhc2_vmmc: usdhc2-vmmcgrp { + fsl,pins = + <MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19 0x41>; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { + fsl,pins = + <MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x194>, + <MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d4>, + <MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d4>, + <MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d4>, + <MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d4>, + <MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d4>, + <MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1>; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { + fsl,pins = + <MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x196>, + <MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d6>, + <MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d6>, + <MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d6>, + <MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d6>, + <MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d6>, + <MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1>; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = + <MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x190>, + <MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d0>, + <MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d0>, + <MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d0>, + <MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d0>, + <MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d0>, + <MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d0>, + <MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d0>, + <MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d0>, + <MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d0>, + <MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x190>; + }; + + pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp { + fsl,pins = + <MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x194>, + <MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d4>, + <MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d4>, + <MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d4>, + <MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d4>, + <MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d4>, + <MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d4>, + <MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d4>, + <MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d4>, + <MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d4>, + <MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x194>; + }; + + pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp { + fsl,pins = + <MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x196>, + <MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d6>, + <MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d6>, + <MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d6>, + <MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d6>, + <MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d6>, + <MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d6>, + <MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d6>, + <MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d6>, + <MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d6>, + <MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x196>; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = + <MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B 0xc6>; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl.dts b/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl.dts index 0e237b2f9541..7bf6f81e87b4 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl.dts +++ b/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl.dts @@ -139,6 +139,13 @@ regulator-max-microvolt = <3300000>; }; + reg_vcc_5v0: regulator-5v0 { + compatible = "regulator-fixed"; + regulator-name = "VCC_5V0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + reserved-memory { #address-cells = <2>; #size-cells = <2>; @@ -447,6 +454,38 @@ status = "okay"; }; +&usb3_0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb0>; + fsl,over-current-active-low; + status = "okay"; +}; + +&usb3_phy0 { + vbus-supply = <®_vcc_5v0>; + status = "okay"; +}; + +&usb_dwc3_0 { + /* dual role is implemented, but not a full featured OTG */ + hnp-disable; + srp-disable; + adp-disable; + dr_mode = "otg"; + usb-role-switch; + role-switch-default-mode = "peripheral"; + status = "okay"; + + connector { + compatible = "gpio-usb-b-connector", "usb-b-connector"; + type = "micro"; + label = "X29"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbcon0>; + id-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; + }; +}; + &usdhc2 { pinctrl-names = "default", "state_100mhz", "state_200mhz"; pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; @@ -672,6 +711,15 @@ <MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX 0x140>; }; + pinctrl_usb0: usb0grp { + fsl,pins = <MX8MP_IOMUXC_GPIO1_IO13__USB1_OTG_OC 0x1c0>, + <MX8MP_IOMUXC_GPIO1_IO12__USB1_OTG_PWR 0x1c0>; + }; + + pinctrl_usbcon0: usb0congrp { + fsl,pins = <MX8MP_IOMUXC_GPIO1_IO10__GPIO1_IO10 0x1c0>; + }; + pinctrl_usdhc2: usdhc2grp { fsl,pins = <MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x192>, <MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d2>, diff --git a/arch/arm64/boot/dts/freescale/imx8mp-venice-gw74xx.dts b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw74xx.dts index 211e6a1b296e..06b4c93c5876 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp-venice-gw74xx.dts +++ b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw74xx.dts @@ -8,6 +8,7 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/linux-event-codes.h> #include <dt-bindings/leds/common.h> +#include <dt-bindings/phy/phy-imx8-pcie.h> #include "imx8mp.dtsi" @@ -100,6 +101,12 @@ }; }; + pcie0_refclk: pcie0-refclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <100000000>; + }; + pps { compatible = "pps-gpio"; pinctrl-names = "default"; @@ -134,13 +141,29 @@ compatible = "regulator-fixed"; regulator-name = "wl"; gpio = <&gpio3 9 GPIO_ACTIVE_HIGH>; - startup-delay-us = <100>; + startup-delay-us = <70000>; enable-active-high; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; }; }; +&A53_0 { + cpu-supply = <®_arm>; +}; + +&A53_1 { + cpu-supply = <®_arm>; +}; + +&A53_2 { + cpu-supply = <®_arm>; +}; + +&A53_3 { + cpu-supply = <®_arm>; +}; + /* off-board header */ &ecspi2 { pinctrl-names = "default"; @@ -199,8 +222,8 @@ &gpio2 { gpio-line-names = "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", "", - "pcie3_wdis#", "", "", "pcie1_wdis@", "pcie2_wdis#", "", "", "", + "", "", "", "", "", "", "pcie3_wdis#", "", + "", "", "pcie2_wdis#", "", "", "", "", "", "", "", "", "", "", "", "", ""; }; @@ -361,7 +384,7 @@ regulator-ramp-delay = <3125>; }; - BUCK2 { + reg_arm: BUCK2 { regulator-name = "BUCK2"; regulator-min-microvolt = <720000>; regulator-max-microvolt = <1025000>; @@ -546,6 +569,28 @@ status = "okay"; }; +&pcie_phy { + fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>; + fsl,clkreq-unsupported; + clocks = <&pcie0_refclk>; + clock-names = "ref"; + status = "okay"; +}; + +&pcie { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcie0>; + reset-gpio = <&gpio2 17 GPIO_ACTIVE_LOW>; + clocks = <&clk IMX8MP_CLK_HSIO_ROOT>, + <&clk IMX8MP_CLK_PCIE_ROOT>, + <&clk IMX8MP_CLK_HSIO_AXI>; + clock-names = "pcie", "pcie_aux", "pcie_bus"; + assigned-clocks = <&clk IMX8MP_CLK_PCIE_AUX>; + assigned-clock-rates = <10000000>; + assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_50M>; + status = "okay"; +}; + /* GPS / off-board header */ &uart1 { pinctrl-names = "default"; @@ -560,6 +605,21 @@ status = "okay"; }; +/* bluetooth HCI */ +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>, <&pinctrl_uart3_gpio>; + cts-gpios = <&gpio3 21 GPIO_ACTIVE_LOW>; + rts-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>; + uart-has-rtscts; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm4330-bt"; + shutdown-gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>; + }; +}; + &uart4 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart4>; @@ -567,20 +627,35 @@ }; /* USB1 - Type C front panel */ -&usb3_phy0 { +&usb3_0 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usb1>; + fsl,over-current-active-low; status = "okay"; }; -&usb3_0 { - fsl,over-current-active-low; +&usb3_phy0 { status = "okay"; }; &usb_dwc3_0 { - dr_mode = "host"; + /* dual role is implemented but not a full featured OTG */ + adp-disable; + hnp-disable; + srp-disable; + dr_mode = "otg"; + usb-role-switch; + role-switch-default-mode = "peripheral"; status = "okay"; + + connector { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbcon1>; + compatible = "gpio-usb-b-connector", "usb-b-connector"; + type = "micro"; + label = "Type-C"; + id-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; + }; }; /* USB2 - USB3.0 Hub */ @@ -600,6 +675,25 @@ status = "okay"; }; +/* SDIO WiFi */ +&usdhc1 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + bus-width = <4>; + non-removable; + vmmc-supply = <®_wifi_en>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + wifi@0 { + compatible = "cypress,cyw4373-fmac"; + reg = <0>; + }; +}; + /* eMMC */ &usdhc3 { assigned-clocks = <&clk IMX8MP_CLK_USDHC3>; @@ -629,7 +723,6 @@ MX8MP_IOMUXC_GPIO1_IO09__GPIO1_IO09 0x40000040 /* DIO0 */ MX8MP_IOMUXC_GPIO1_IO11__GPIO1_IO11 0x40000040 /* DIO1 */ MX8MP_IOMUXC_NAND_DQS__GPIO3_IO14 0x40000040 /* M2SKT_OFF# */ - MX8MP_IOMUXC_SD2_DATA2__GPIO2_IO17 0x40000150 /* PCIE1_WDIS# */ MX8MP_IOMUXC_SD2_DATA3__GPIO2_IO18 0x40000150 /* PCIE2_WDIS# */ MX8MP_IOMUXC_SD2_CMD__GPIO2_IO14 0x40000150 /* PCIE3_WDIS# */ MX8MP_IOMUXC_NAND_DATA00__GPIO3_IO06 0x40000040 /* M2SKT_RST# */ @@ -742,6 +835,12 @@ >; }; + pinctrl_pcie0: pciegrp { + fsl,pins = < + MX8MP_IOMUXC_SD2_DATA2__GPIO2_IO17 0x110 + >; + }; + pinctrl_pmic: pmicgrp { fsl,pins = < MX8MP_IOMUXC_NAND_DATA01__GPIO3_IO07 0x140 @@ -829,7 +928,12 @@ pinctrl_usb1: usb1grp { fsl,pins = < MX8MP_IOMUXC_GPIO1_IO13__USB1_OTG_OC 0x140 - MX8MP_IOMUXC_GPIO1_IO10__USB1_OTG_ID 0x140 + >; + }; + + pinctrl_usbcon1: usb1congrp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO10__GPIO1_IO10 0x140 >; }; @@ -844,6 +948,28 @@ >; }; + pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK 0x194 + MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD 0x1d4 + MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0 0x1d4 + MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1 0x1d4 + MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2 0x1d4 + MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3 0x1d4 + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK 0x196 + MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD 0x1d6 + MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0 0x1d6 + MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1 0x1d6 + MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2 0x1d6 + MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3 0x1d6 + >; + }; + pinctrl_usdhc3: usdhc3grp { fsl,pins = < MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x190 diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi index 1c74c6a19449..7b712d1888ea 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi @@ -146,6 +146,22 @@ }; }; +&A53_0 { + cpu-supply = <®_vdd_arm>; +}; + +&A53_1 { + cpu-supply = <®_vdd_arm>; +}; + +&A53_2 { + cpu-supply = <®_vdd_arm>; +}; + +&A53_3 { + cpu-supply = <®_vdd_arm>; +}; + &cpu_alert0 { temperature = <95000>; }; @@ -286,7 +302,6 @@ status = "disabled"; }; - /* Verdin CAN_2 */ &flexcan2 { pinctrl-names = "default"; @@ -454,7 +469,7 @@ regulator-ramp-delay = <3125>; }; - BUCK2 { + reg_vdd_arm: BUCK2 { nxp,dvs-run-voltage = <950000>; nxp,dvs-standby-voltage = <850000>; regulator-always-on; diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp.dtsi index fe178b7d063c..53493dc7d976 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi @@ -5,8 +5,10 @@ #include <dt-bindings/clock/imx8mp-clock.h> #include <dt-bindings/power/imx8mp-power.h> +#include <dt-bindings/reset/imx8mp-reset.h> #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> +#include <dt-bindings/interconnect/fsl,imx8mp.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/thermal/thermal.h> @@ -469,6 +471,11 @@ wakeup-source; status = "disabled"; }; + + snvs_lpgpr: snvs-lpgpr { + compatible = "fsl,imx8mp-snvs-lpgpr", + "fsl,imx7d-snvs-lpgpr"; + }; }; clk: clock-controller@30380000 { @@ -597,6 +604,33 @@ reg = <IMX8MP_POWER_DOMAIN_MEDIAMIX_ISPDWP>; clocks = <&clk IMX8MP_CLK_MEDIA_ISP_ROOT>; }; + + pgc_vpumix: power-domain@19 { + #power-domain-cells = <0>; + reg = <IMX8MP_POWER_DOMAIN_VPUMIX>; + clocks =<&clk IMX8MP_CLK_VPU_ROOT>; + }; + + pgc_vpu_g1: power-domain@20 { + #power-domain-cells = <0>; + power-domains = <&pgc_vpumix>; + reg = <IMX8MP_POWER_DOMAIN_VPU_G1>; + clocks = <&clk IMX8MP_CLK_VPU_G1_ROOT>; + }; + + pgc_vpu_g2: power-domain@21 { + #power-domain-cells = <0>; + power-domains = <&pgc_vpumix>; + reg = <IMX8MP_POWER_DOMAIN_VPU_G2>; + clocks = <&clk IMX8MP_CLK_VPU_G2_ROOT>; + }; + + pgc_vpu_vc8000e: power-domain@22 { + #power-domain-cells = <0>; + power-domains = <&pgc_vpumix>; + reg = <IMX8MP_POWER_DOMAIN_VPU_VC8000E>; + clocks = <&clk IMX8MP_CLK_VPU_VC8KE_ROOT>; + }; }; }; }; @@ -1064,6 +1098,18 @@ "lcdif1", "isi", "mipi-csi2", "lcdif2", "isp", "dwe", "mipi-dsi2"; + interconnects = + <&noc IMX8MP_ICM_LCDIF_RD &noc IMX8MP_ICN_MEDIA>, + <&noc IMX8MP_ICM_LCDIF_WR &noc IMX8MP_ICN_MEDIA>, + <&noc IMX8MP_ICM_ISI0 &noc IMX8MP_ICN_MEDIA>, + <&noc IMX8MP_ICM_ISI1 &noc IMX8MP_ICN_MEDIA>, + <&noc IMX8MP_ICM_ISI2 &noc IMX8MP_ICN_MEDIA>, + <&noc IMX8MP_ICM_ISP0 &noc IMX8MP_ICN_MEDIA>, + <&noc IMX8MP_ICM_ISP1 &noc IMX8MP_ICN_MEDIA>, + <&noc IMX8MP_ICM_DWE &noc IMX8MP_ICN_MEDIA>; + interconnect-names = "lcdif-rd", "lcdif-wr", "isi0", + "isi1", "isi2", "isp0", "isp1", + "dwe"; clocks = <&clk IMX8MP_CLK_MEDIA_APB_ROOT>, <&clk IMX8MP_CLK_MEDIA_AXI_ROOT>, <&clk IMX8MP_CLK_MEDIA_CAM1_PIX_ROOT>, @@ -1084,6 +1130,17 @@ #power-domain-cells = <1>; }; + pcie_phy: pcie-phy@32f00000 { + compatible = "fsl,imx8mp-pcie-phy"; + reg = <0x32f00000 0x10000>; + resets = <&src IMX8MP_RESET_PCIEPHY>, + <&src IMX8MP_RESET_PCIEPHY_PERST>; + reset-names = "pciephy", "perst"; + power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_PCIE_PHY>; + #phy-cells = <0>; + status = "disabled"; + }; + hsio_blk_ctrl: blk-ctrl@32f10000 { compatible = "fsl,imx8mp-hsio-blk-ctrl", "syscon"; reg = <0x32f10000 0x24>; @@ -1095,10 +1152,46 @@ <&pgc_hsiomix>, <&pgc_pcie_phy>; power-domain-names = "bus", "usb", "usb-phy1", "usb-phy2", "pcie", "pcie-phy"; + interconnects = <&noc IMX8MP_ICM_NOC_PCIE &noc IMX8MP_ICN_HSIO>, + <&noc IMX8MP_ICM_USB1 &noc IMX8MP_ICN_HSIO>, + <&noc IMX8MP_ICM_USB2 &noc IMX8MP_ICN_HSIO>, + <&noc IMX8MP_ICM_PCIE &noc IMX8MP_ICN_HSIO>; + interconnect-names = "noc-pcie", "usb1", "usb2", "pcie"; #power-domain-cells = <1>; }; }; + pcie: pcie@33800000 { + compatible = "fsl,imx8mp-pcie"; + reg = <0x33800000 0x400000>, <0x1ff00000 0x80000>; + reg-names = "dbi", "config"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + bus-range = <0x00 0xff>; + ranges = <0x81000000 0 0x00000000 0x1ff80000 0 0x00010000>, /* downstream I/O 64KB */ + <0x82000000 0 0x18000000 0x18000000 0 0x07f00000>; /* non-prefetchable memory */ + num-lanes = <1>; + num-viewport = <4>; + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &gic GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 2 &gic GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 3 &gic GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 4 &gic GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; + fsl,max-link-speed = <3>; + linux,pci-domain = <0>; + power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_PCIE>; + resets = <&src IMX8MP_RESET_PCIE_CTRL_APPS_EN>, + <&src IMX8MP_RESET_PCIE_CTRL_APPS_TURNOFF>; + reset-names = "apps", "turnoff"; + phys = <&pcie_phy>; + phy-names = "pcie-phy"; + status = "disabled"; + }; + gpu3d: gpu@38000000 { compatible = "vivante,gc"; reg = <0x38000000 0x8000>; @@ -1130,6 +1223,23 @@ power-domains = <&pgc_gpu2d>; }; + vpumix_blk_ctrl: blk-ctrl@38330000 { + compatible = "fsl,imx8mp-vpu-blk-ctrl", "syscon"; + reg = <0x38330000 0x100>; + #power-domain-cells = <1>; + power-domains = <&pgc_vpumix>, <&pgc_vpu_g1>, + <&pgc_vpu_g2>, <&pgc_vpu_vc8000e>; + power-domain-names = "bus", "g1", "g2", "vc8000e"; + clocks = <&clk IMX8MP_CLK_VPU_G1_ROOT>, + <&clk IMX8MP_CLK_VPU_G2_ROOT>, + <&clk IMX8MP_CLK_VPU_VC8KE_ROOT>; + clock-names = "g1", "g2", "vc8000e"; + interconnects = <&noc IMX8MP_ICM_VPU_G1 &noc IMX8MP_ICN_VIDEO>, + <&noc IMX8MP_ICM_VPU_G2 &noc IMX8MP_ICN_VIDEO>, + <&noc IMX8MP_ICM_VPU_H1 &noc IMX8MP_ICN_VIDEO>; + interconnect-names = "g1", "g2", "vc8000e"; + }; + gic: interrupt-controller@38800000 { compatible = "arm,gic-v3"; reg = <0x38800000 0x10000>, diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi index 9eec8a7eecfc..ae08556b2ef2 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi @@ -7,6 +7,7 @@ #include "dt-bindings/input/input.h" #include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/leds/common.h> #include "dt-bindings/pwm/pwm.h" #include "dt-bindings/usb/pd.h" #include "imx8mq.dtsi" @@ -54,6 +55,31 @@ }; }; + led-controller { + compatible = "pwm-leds"; + + led-0 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_BLUE>; + max-brightness = <248>; + pwms = <&pwm2 0 50000 0>; + }; + + led-1 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_GREEN>; + max-brightness = <248>; + pwms = <&pwm4 0 50000 0>; + }; + + led-2 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_RED>; + max-brightness = <248>; + pwms = <&pwm3 0 50000 0>; + }; + }; + reg_aud_1v8: regulator-audio-1v8 { compatible = "regulator-fixed"; pinctrl-names = "default"; @@ -747,6 +773,10 @@ interrupt-names = "irq"; connector { + compatible = "usb-c-connector"; + label = "USB-C"; + data-role = "dual"; + ports { #address-cells = <1>; #size-cells = <0>; @@ -1070,6 +1100,12 @@ pinctrl-0 = <&pinctrl_i2c4>; status = "okay"; + vcm@c { + compatible = "dongwoon,dw9714"; + reg = <0x0c>; + vcc-supply = <®_csi_1v8>; + }; + bat: fuel-gauge@36 { compatible = "maxim,max17055"; reg = <0x36>; @@ -1077,6 +1113,7 @@ interrupts = <20 IRQ_TYPE_LEVEL_LOW>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_gauge>; + power-supplies = <&bq25895>; maxim,over-heat-temp = <700>; maxim,over-volt = <4500>; maxim,rsns-microohm = <5000>; @@ -1106,8 +1143,6 @@ }; &mipi_csi1 { - #address-cells = <1>; - #size-cells = <0>; status = "okay"; ports { @@ -1265,6 +1300,7 @@ #size-cells = <0>; dr_mode = "otg"; snps,dis_u3_susphy_quirk; + usb-role-switch; status = "okay"; port@0 { diff --git a/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts b/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts index 8956a46788fa..055031bba8c4 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts +++ b/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts @@ -210,7 +210,6 @@ status = "okay"; }; - ®_1p8v { vin-supply = <®_main_5v>; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi index e9f0cdd10ab6..19eaa523564d 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi @@ -534,7 +534,7 @@ status = "disabled"; }; - sdma2: sdma@302c0000 { + sdma2: dma-controller@302c0000 { compatible = "fsl,imx8mq-sdma","fsl,imx7d-sdma"; reg = <0x302c0000 0x10000>; interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; @@ -1302,7 +1302,7 @@ status = "disabled"; }; - sdma1: sdma@30bd0000 { + sdma1: dma-controller@30bd0000 { compatible = "fsl,imx8mq-sdma","fsl,imx7d-sdma"; reg = <0x30bd0000 0x10000>; interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; diff --git a/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts b/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts index 33e84c4e9ed8..f1c6d933a17c 100644 --- a/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts +++ b/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts @@ -19,6 +19,21 @@ device_type = "memory"; reg = <0x0 0x80000000 0 0x80000000>; }; + + clock_ext_rmii: clock-ext-rmii { + compatible = "fixed-clock"; + clock-frequency = <50000000>; + clock-output-names = "ext_rmii_clk"; + #clock-cells = <0>; + }; + + clock_ext_ts: clock-ext-ts { + compatible = "fixed-clock"; + /* External ts clock is 50MHZ from PHY on EVK board. */ + clock-frequency = <50000000>; + clock-output-names = "ext_ts_clk"; + #clock-cells = <0>; + }; }; &lpuart5 { @@ -38,7 +53,49 @@ status = "okay"; }; +&fec { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&pinctrl_enet>; + pinctrl-1 = <&pinctrl_enet>; + clocks = <&cgc1 IMX8ULP_CLK_XBAR_DIVBUS>, + <&pcc4 IMX8ULP_CLK_ENET>, + <&cgc1 IMX8ULP_CLK_ENET_TS_SEL>, + <&clock_ext_rmii>; + clock-names = "ipg", "ahb", "ptp", "enet_clk_ref"; + assigned-clocks = <&cgc1 IMX8ULP_CLK_ENET_TS_SEL>; + assigned-clock-parents = <&clock_ext_ts>; + phy-mode = "rmii"; + phy-handle = <ðphy>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy: ethernet-phy@1 { + reg = <1>; + micrel,led-mode = <1>; + }; + }; +}; + &iomuxc1 { + pinctrl_enet: enetgrp { + fsl,pins = < + MX8ULP_PAD_PTE15__ENET0_MDC 0x43 + MX8ULP_PAD_PTE14__ENET0_MDIO 0x43 + MX8ULP_PAD_PTE17__ENET0_RXER 0x43 + MX8ULP_PAD_PTE18__ENET0_CRS_DV 0x43 + MX8ULP_PAD_PTF1__ENET0_RXD0 0x43 + MX8ULP_PAD_PTE20__ENET0_RXD1 0x43 + MX8ULP_PAD_PTE16__ENET0_TXEN 0x43 + MX8ULP_PAD_PTE23__ENET0_TXD0 0x43 + MX8ULP_PAD_PTE22__ENET0_TXD1 0x43 + MX8ULP_PAD_PTE19__ENET0_REFCLK 0x43 + MX8ULP_PAD_PTF10__ENET0_1588_CLKIN 0x43 + >; + }; + pinctrl_lpuart5: lpuart5grp { fsl,pins = < MX8ULP_PAD_PTF14__LPUART5_TX 0x3 diff --git a/arch/arm64/boot/dts/freescale/imx8ulp-pinfunc.h b/arch/arm64/boot/dts/freescale/imx8ulp-pinfunc.h index b204ac79b449..b204ac79b449 100755..100644 --- a/arch/arm64/boot/dts/freescale/imx8ulp-pinfunc.h +++ b/arch/arm64/boot/dts/freescale/imx8ulp-pinfunc.h diff --git a/arch/arm64/boot/dts/freescale/imx8ulp.dtsi b/arch/arm64/boot/dts/freescale/imx8ulp.dtsi index bb56390b8f54..06ce5f19aa8a 100644 --- a/arch/arm64/boot/dts/freescale/imx8ulp.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8ulp.dtsi @@ -16,6 +16,7 @@ #size-cells = <2>; aliases { + ethernet0 = &fec; gpio0 = &gpiod; gpio1 = &gpioe; gpio2 = &gpiof; @@ -62,6 +63,14 @@ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; }; + pmu { + compatible = "arm,cortex-a35-pmu"; + interrupt-parent = <&gic>; + interrupts = <GIC_PPI 7 + (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>; + interrupt-affinity = <&A35_0>, <&A35_1>; + }; + psci { compatible = "arm,psci-1.0"; method = "smc"; @@ -111,7 +120,7 @@ #size-cells = <1>; ranges = <0 0x0 0x2201f000 0x1000>; - scmi_buf: scmi-buf@0 { + scmi_buf: scmi-sram-section@0 { compatible = "arm,scmi-shmem"; reg = <0x0 0x400>; }; @@ -143,6 +152,13 @@ #size-cells = <1>; ranges = <0x0 0x0 0x0 0x40000000>; + s4muap: mailbox@27020000 { + compatible = "fsl,imx8ulp-mu-s4"; + reg = <0x27020000 0x10000>; + interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <2>; + }; + per_bridge3: bus@29000000 { compatible = "simple-bus"; reg = <0x29000000 0x800000>; @@ -150,6 +166,23 @@ #size-cells = <1>; ranges; + mu: mailbox@29220000 { + compatible = "fsl,imx8ulp-mu"; + reg = <0x29220000 0x10000>; + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <2>; + status = "disabled"; + }; + + mu3: mailbox@29230000 { + compatible = "fsl,imx8ulp-mu"; + reg = <0x29230000 0x10000>; + interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pcc3 IMX8ULP_CLK_MU3_A>; + #mbox-cells = <2>; + status = "disabled"; + }; + wdog3: watchdog@292a0000 { compatible = "fsl,imx8ulp-wdt", "fsl,imx7ulp-wdt"; reg = <0x292a0000 0x10000>; @@ -163,8 +196,6 @@ cgc1: clock-controller@292c0000 { compatible = "fsl,imx8ulp-cgc1"; reg = <0x292c0000 0x10000>; - clocks = <&rosc>, <&sosc>, <&frosc>, <&lposc>; - clock-names = "rosc", "sosc", "frosc", "lposc"; #clock-cells = <1>; }; @@ -193,7 +224,7 @@ <&pcc3 IMX8ULP_CLK_LPI2C4>; clock-names = "per", "ipg"; assigned-clocks = <&pcc3 IMX8ULP_CLK_LPI2C4>; - assigned-clock-parents = <&cgc1 IMX8ULP_CLK_XBAR_DIVBUS>; + assigned-clock-parents = <&cgc1 IMX8ULP_CLK_FROSC_DIV2>; assigned-clock-rates = <48000000>; status = "disabled"; }; @@ -206,7 +237,7 @@ <&pcc3 IMX8ULP_CLK_LPI2C5>; clock-names = "per", "ipg"; assigned-clocks = <&pcc3 IMX8ULP_CLK_LPI2C5>; - assigned-clock-parents = <&cgc1 IMX8ULP_CLK_XBAR_DIVBUS>; + assigned-clock-parents = <&cgc1 IMX8ULP_CLK_FROSC_DIV2>; assigned-clock-rates = <48000000>; status = "disabled"; }; @@ -239,8 +270,8 @@ <&pcc3 IMX8ULP_CLK_LPSPI4>; clock-names = "per", "ipg"; assigned-clocks = <&pcc3 IMX8ULP_CLK_LPSPI4>; - assigned-clock-parents = <&cgc1 IMX8ULP_CLK_XBAR_DIVBUS>; - assigned-clock-rates = <16000000>; + assigned-clock-parents = <&cgc1 IMX8ULP_CLK_FROSC_DIV2>; + assigned-clock-rates = <48000000>; status = "disabled"; }; @@ -254,8 +285,8 @@ <&pcc3 IMX8ULP_CLK_LPSPI5>; clock-names = "per", "ipg"; assigned-clocks = <&pcc3 IMX8ULP_CLK_LPSPI5>; - assigned-clock-parents = <&cgc1 IMX8ULP_CLK_XBAR_DIVBUS>; - assigned-clock-rates = <16000000>; + assigned-clock-parents = <&cgc1 IMX8ULP_CLK_FROSC_DIV2>; + assigned-clock-rates = <48000000>; status = "disabled"; }; }; @@ -282,7 +313,7 @@ <&pcc4 IMX8ULP_CLK_LPI2C6>; clock-names = "per", "ipg"; assigned-clocks = <&pcc4 IMX8ULP_CLK_LPI2C6>; - assigned-clock-parents = <&cgc1 IMX8ULP_CLK_XBAR_DIVBUS>; + assigned-clock-parents = <&cgc1 IMX8ULP_CLK_FROSC_DIV2>; assigned-clock-rates = <48000000>; status = "disabled"; }; @@ -295,7 +326,7 @@ <&pcc4 IMX8ULP_CLK_LPI2C7>; clock-names = "per", "ipg"; assigned-clocks = <&pcc4 IMX8ULP_CLK_LPI2C7>; - assigned-clock-parents = <&cgc1 IMX8ULP_CLK_XBAR_DIVBUS>; + assigned-clock-parents = <&cgc1 IMX8ULP_CLK_FROSC_DIV2>; assigned-clock-rates = <48000000>; status = "disabled"; }; @@ -367,6 +398,16 @@ bus-width = <4>; status = "disabled"; }; + + fec: ethernet@29950000 { + compatible = "fsl,imx8ulp-fec", "fsl,imx6ul-fec", "fsl,imx6q-fec"; + reg = <0x29950000 0x10000>; + interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "int0"; + fsl,num-tx-queues = <1>; + fsl,num-rx-queues = <1>; + status = "disabled"; + }; }; gpioe: gpio@2d000080 { @@ -407,8 +448,6 @@ cgc2: clock-controller@2da60000 { compatible = "fsl,imx8ulp-cgc2"; reg = <0x2da60000 0x10000>; - clocks = <&sosc>, <&frosc>; - clock-names = "sosc", "frosc"; #clock-cells = <1>; }; diff --git a/arch/arm64/boot/dts/freescale/imx93.dtsi b/arch/arm64/boot/dts/freescale/imx93.dtsi index f83a07c7c9b1..3a5713bb4880 100644 --- a/arch/arm64/boot/dts/freescale/imx93.dtsi +++ b/arch/arm64/boot/dts/freescale/imx93.dtsi @@ -7,6 +7,7 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/power/fsl,imx93-power.h> #include "imx93-pinfunc.h" @@ -16,6 +17,14 @@ #size-cells = <2>; aliases { + i2c0 = &lpi2c1; + i2c1 = &lpi2c2; + i2c2 = &lpi2c3; + i2c3 = &lpi2c4; + i2c4 = &lpi2c5; + i2c5 = &lpi2c6; + i2c6 = &lpi2c7; + i2c7 = &lpi2c8; mmc0 = &usdhc1; mmc1 = &usdhc2; mmc2 = &usdhc3; @@ -72,6 +81,11 @@ clock-output-names = "clk_ext1"; }; + pmu { + compatible = "arm,cortex-a55-pmu"; + interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>; + }; + psci { compatible = "arm,psci-1.0"; method = "smc"; @@ -112,6 +126,11 @@ #size-cells = <1>; ranges; + anomix_ns_gpr: syscon@44210000 { + compatible = "fsl,imx93-aonmix-ns-syscfg", "syscon"; + reg = <0x44210000 0x1000>; + }; + mu1: mailbox@44230000 { compatible = "fsl,imx93-mu", "fsl,imx8ulp-mu"; reg = <0x44230000 0x10000>; @@ -128,6 +147,50 @@ clock-names = "per"; }; + lpi2c1: i2c@44340000 { + compatible = "fsl,imx93-lpi2c", "fsl,imx7ulp-lpi2c"; + reg = <0x44340000 0x10000>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX93_CLK_LPI2C1_GATE>, + <&clk IMX93_CLK_BUS_AON>; + clock-names = "per", "ipg"; + status = "disabled"; + }; + + lpi2c2: i2c@44350000 { + compatible = "fsl,imx93-lpi2c", "fsl,imx7ulp-lpi2c"; + reg = <0x44350000 0x10000>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX93_CLK_LPI2C2_GATE>, + <&clk IMX93_CLK_BUS_AON>; + clock-names = "per", "ipg"; + status = "disabled"; + }; + + lpspi1: spi@44360000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx93-spi", "fsl,imx7ulp-spi"; + reg = <0x44360000 0x10000>; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX93_CLK_LPSPI1_GATE>, + <&clk IMX93_CLK_BUS_AON>; + clock-names = "per", "ipg"; + status = "disabled"; + }; + + lpspi2: spi@44370000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx93-spi", "fsl,imx7ulp-spi"; + reg = <0x44370000 0x10000>; + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX93_CLK_LPSPI2_GATE>, + <&clk IMX93_CLK_BUS_AON>; + clock-names = "per", "ipg"; + status = "disabled"; + }; + lpuart1: serial@44380000 { compatible = "fsl,imx93-lpuart", "fsl,imx7ulp-lpuart"; reg = <0x44380000 0x1000>; @@ -161,6 +224,30 @@ status = "okay"; }; + src: system-controller@44460000 { + compatible = "fsl,imx93-src", "syscon"; + reg = <0x44460000 0x10000>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + mediamix: power-domain@44462400 { + compatible = "fsl,imx93-src-slice"; + reg = <0x44462400 0x400>, <0x44465800 0x400>; + #power-domain-cells = <0>; + clocks = <&clk IMX93_CLK_MEDIA_AXI>, + <&clk IMX93_CLK_MEDIA_APB>; + }; + + mlmix: power-domain@44461800 { + compatible = "fsl,imx93-src-slice"; + reg = <0x44461800 0x400>, <0x44464800 0x400>; + #power-domain-cells = <0>; + clocks = <&clk IMX93_CLK_ML_APB>, + <&clk IMX93_CLK_ML>; + }; + }; + anatop: anatop@44480000 { compatible = "fsl,imx93-anatop", "syscon"; reg = <0x44480000 0x10000>; @@ -174,6 +261,11 @@ #size-cells = <1>; ranges; + wakeupmix_gpr: syscon@42420000 { + compatible = "fsl,imx93-wakeupmix-syscfg", "syscon"; + reg = <0x42420000 0x1000>; + }; + mu2: mailbox@42440000 { compatible = "fsl,imx93-mu", "fsl,imx8ulp-mu"; reg = <0x42440000 0x10000>; @@ -182,6 +274,26 @@ status = "disabled"; }; + lpi2c3: i2c@42530000 { + compatible = "fsl,imx93-lpi2c", "fsl,imx7ulp-lpi2c"; + reg = <0x42530000 0x10000>; + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX93_CLK_LPI2C3_GATE>, + <&clk IMX93_CLK_BUS_WAKEUP>; + clock-names = "per", "ipg"; + status = "disabled"; + }; + + lpi2c4: i2c@42540000 { + compatible = "fsl,imx93-lpi2c", "fsl,imx7ulp-lpi2c"; + reg = <0x42540000 0x10000>; + interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX93_CLK_LPI2C4_GATE>, + <&clk IMX93_CLK_BUS_WAKEUP>; + clock-names = "per", "ipg"; + status = "disabled"; + }; + lpuart3: serial@42570000 { compatible = "fsl,imx93-lpuart", "fsl,imx7ulp-lpuart"; reg = <0x42570000 0x1000>; @@ -235,6 +347,47 @@ clock-names = "ipg"; status = "disabled"; }; + + lpi2c5: i2c@426b0000 { + compatible = "fsl,imx93-lpi2c", "fsl,imx7ulp-lpi2c"; + reg = <0x426b0000 0x10000>; + interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX93_CLK_LPI2C5_GATE>, + <&clk IMX93_CLK_BUS_WAKEUP>; + clock-names = "per", "ipg"; + status = "disabled"; + }; + + lpi2c6: i2c@426c0000 { + compatible = "fsl,imx93-lpi2c", "fsl,imx7ulp-lpi2c"; + reg = <0x426c0000 0x10000>; + interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX93_CLK_LPI2C6_GATE>, + <&clk IMX93_CLK_BUS_WAKEUP>; + clock-names = "per", "ipg"; + status = "disabled"; + }; + + lpi2c7: i2c@426d0000 { + compatible = "fsl,imx93-lpi2c", "fsl,imx7ulp-lpi2c"; + reg = <0x426d0000 0x10000>; + interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX93_CLK_LPI2C7_GATE>, + <&clk IMX93_CLK_BUS_WAKEUP>; + clock-names = "per", "ipg"; + status = "disabled"; + }; + + lpi2c8: i2c@426e0000 { + compatible = "fsl,imx93-lpi2c", "fsl,imx7ulp-lpi2c"; + reg = <0x426e0000 0x10000>; + interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX93_CLK_LPI2C8_GATE>, + <&clk IMX93_CLK_BUS_WAKEUP>; + clock-names = "per", "ipg"; + status = "disabled"; + }; + }; aips3: bus@42800000 { @@ -248,8 +401,8 @@ compatible = "fsl,imx93-usdhc", "fsl,imx8mm-usdhc"; reg = <0x42850000 0x10000>; interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clk IMX93_CLK_DUMMY>, - <&clk IMX93_CLK_DUMMY>, + clocks = <&clk IMX93_CLK_BUS_WAKEUP>, + <&clk IMX93_CLK_WAKEUP_AXI>, <&clk IMX93_CLK_USDHC1_GATE>; clock-names = "ipg", "ahb", "per"; bus-width = <8>; @@ -262,8 +415,8 @@ compatible = "fsl,imx93-usdhc", "fsl,imx8mm-usdhc"; reg = <0x42860000 0x10000>; interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clk IMX93_CLK_DUMMY>, - <&clk IMX93_CLK_DUMMY>, + clocks = <&clk IMX93_CLK_BUS_WAKEUP>, + <&clk IMX93_CLK_WAKEUP_AXI>, <&clk IMX93_CLK_USDHC2_GATE>; clock-names = "ipg", "ahb", "per"; bus-width = <4>; @@ -276,8 +429,8 @@ compatible = "fsl,imx93-usdhc", "fsl,imx8mm-usdhc"; reg = <0x428b0000 0x10000>; interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clk IMX93_CLK_DUMMY>, - <&clk IMX93_CLK_DUMMY>, + clocks = <&clk IMX93_CLK_BUS_WAKEUP>, + <&clk IMX93_CLK_WAKEUP_AXI>, <&clk IMX93_CLK_USDHC3_GATE>; clock-names = "ipg", "ahb", "per"; bus-width = <4>; @@ -295,6 +448,9 @@ interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; interrupt-controller; #interrupt-cells = <2>; + clocks = <&clk IMX93_CLK_GPIO2_GATE>, + <&clk IMX93_CLK_GPIO2_GATE>; + clock-names = "gpio", "port"; gpio-ranges = <&iomuxc 0 32 32>; }; @@ -306,6 +462,9 @@ interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; interrupt-controller; #interrupt-cells = <2>; + clocks = <&clk IMX93_CLK_GPIO3_GATE>, + <&clk IMX93_CLK_GPIO3_GATE>; + clock-names = "gpio", "port"; gpio-ranges = <&iomuxc 0 64 32>; }; @@ -317,6 +476,9 @@ interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>; interrupt-controller; #interrupt-cells = <2>; + clocks = <&clk IMX93_CLK_GPIO4_GATE>, + <&clk IMX93_CLK_GPIO4_GATE>; + clock-names = "gpio", "port"; gpio-ranges = <&iomuxc 0 96 32>; }; @@ -328,7 +490,39 @@ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; interrupt-controller; #interrupt-cells = <2>; + clocks = <&clk IMX93_CLK_GPIO1_GATE>, + <&clk IMX93_CLK_GPIO1_GATE>; + clock-names = "gpio", "port"; gpio-ranges = <&iomuxc 0 0 32>; }; + + s4muap: mailbox@47520000 { + compatible = "fsl,imx93-mu-s4"; + reg = <0x47520000 0x10000>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "txirq", "rxirq"; + #mbox-cells = <2>; + }; + + media_blk_ctrl: system-controller@4ac10000 { + compatible = "fsl,imx93-media-blk-ctrl", "syscon"; + reg = <0x4ac10000 0x10000>; + power-domains = <&mediamix>; + clocks = <&clk IMX93_CLK_MEDIA_APB>, + <&clk IMX93_CLK_MEDIA_AXI>, + <&clk IMX93_CLK_NIC_MEDIA_GATE>, + <&clk IMX93_CLK_MEDIA_DISP_PIX>, + <&clk IMX93_CLK_CAM_PIX>, + <&clk IMX93_CLK_PXP_GATE>, + <&clk IMX93_CLK_LCDIF_GATE>, + <&clk IMX93_CLK_ISI_GATE>, + <&clk IMX93_CLK_MIPI_CSI_GATE>, + <&clk IMX93_CLK_MIPI_DSI_GATE>; + clock-names = "apb", "axi", "nic", "disp", "cam", + "pxp", "lcdif", "isi", "csi", "dsi"; + #power-domain-cells = <1>; + status = "disabled"; + }; }; }; |