arm64: dts: marvell: split Methode uDPU DTS

Split the Methode uDPU DTS into a common DTSI as preparation for adding
support for Methode eDPU which is based on the uDPU to avoid duplication.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

1 files changed, 1 insertions, 149 deletions

diff --git a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
index b2d7f24fa940..c76eceabd33e 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
@@ -1,66 +1,13 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Device tree for the uDPU board.
- * Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
- * Copyright (C) 2016 Marvell
- * Copyright (C) 2019 Methode Electronics
- * Copyright (C) 2019 Telus
- *
- * Vladimir Vid <vladimir.vid@sartura.hr>
- */
 
 /dts-v1/;
 
-#include <dt-bindings/gpio/gpio.h>
-#include "armada-372x.dtsi"
+#include "armada-3720-uDPU.dtsi"
 
 / {
 	model = "Methode uDPU Board";
 	compatible = "methode,udpu", "marvell,armada3720", "marvell,armada3710";
 
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	memory@0 {
-		device_type = "memory";
-		reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		led-power1 {
-			label = "udpu:green:power";
-			gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
-		};
-
-		led-power2 {
-			label = "udpu:red:power";
-			gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
-		};
-
-		led-network1 {
-			label = "udpu:green:network";
-			gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
-		};
-
-		led-network2 {
-			label = "udpu:red:network";
-			gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
-		};
-
-		led-alarm1 {
-			label = "udpu:green:alarm";
-			gpios = <&gpionb 15 GPIO_ACTIVE_LOW>;
-		};
-
-		led-alarm2 {
-			label = "udpu:red:alarm";
-			gpios = <&gpionb 16 GPIO_ACTIVE_LOW>;
-		};
-	};
-
 	sfp_eth0: sfp-eth0 {
 		compatible = "sff,sfp";
 		i2c-bus = <&i2c0>;
@@ -70,55 +17,6 @@
 		tx-fault-gpios = <&gpiosb 5 GPIO_ACTIVE_HIGH>;
 		maximum-power-milliwatt = <3000>;
 	};
-
-	sfp_eth1: sfp-eth1 {
-		compatible = "sff,sfp";
-		i2c-bus = <&i2c1>;
-		los-gpios = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios = <&gpiosb 8 GPIO_ACTIVE_LOW>;
-		tx-disable-gpios = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
-		tx-fault-gpios = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
-		maximum-power-milliwatt = <3000>;
-	};
-};
-
-&sdhci0 {
-	status = "okay";
-	bus-width = <8>;
-	mmc-ddr-1_8v;
-	mmc-hs400-1_8v;
-	marvell,pad-type = "fixed-1-8v";
-	non-removable;
-	no-sd;
-	no-sdio;
-};
-
-&spi0 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&spi_quad_pins>;
-
-	flash@0 {
-		compatible = "jedec,spi-nor";
-		reg = <0>;
-		spi-max-frequency = <54000000>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			partition@0 {
-				label = "firmware";
-				reg = <0x0 0x180000>;
-			};
-
-			partition@180000 {
-				label = "u-boot-env";
-				reg = <0x180000 0x10000>;
-			};
-		};
-	};
 };
 
 &pinctrl_nb {
@@ -126,11 +24,6 @@
 		groups = "i2c1";
 		function = "gpio";
 	};
-
-	i2c2_recovery_pins: i2c2-recovery-pins {
-		groups = "i2c2";
-		function = "gpio";
-	};
 };
 
 &i2c0 {
@@ -143,48 +36,7 @@
 	sda-gpios = <&gpionb 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 };
 
-&i2c1 {
-	status = "okay";
-	pinctrl-names = "default", "recovery";
-	pinctrl-0 = <&i2c2_pins>;
-	pinctrl-1 = <&i2c2_recovery_pins>;
-	/delete-property/mrvl,i2c-fast-mode;
-	scl-gpios = <&gpionb 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-	sda-gpios = <&gpionb 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-
-	temp-sensor@48 {
-		compatible = "ti,tmp75c";
-		reg = <0x48>;
-	};
-
-	temp-sensor@49 {
-		compatible = "ti,tmp75c";
-		reg = <0x49>;
-	};
-};
-
 &eth0 {
 	phy-mode = "sgmii";
-	status = "okay";
-	managed = "in-band-status";
-	phys = <&comphy1 0>;
 	sfp = <&sfp_eth0>;
 };
-
-&eth1 {
-	phy-mode = "sgmii";
-	status = "okay";
-	managed = "in-band-status";
-	phys = <&comphy0 1>;
-	sfp = <&sfp_eth1>;
-};
-
-&usb3 {
-	status = "okay";
-	phys = <&usb2_utmi_otg_phy>;
-	phy-names = "usb2-utmi-otg-phy";
-};
-
-&uart0 {
-	status = "okay";
-};