Merge tag 'mvebu-dt64-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/dt

mvebu dt64 for 6.1 (part 1)

 - Add UART1-3 for AC5/AC5X SoC
 - Improve uDPU support (Aramda 3720 based board)
 - Add new eDPU based on uDPU

* tag 'mvebu-dt64-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
  arm64: dts: marvell: 98dx25xx: use correct property for i2c gpios
  arm64: dts: marvell: add support for Methode eDPU
  dt-bindings: marvell: armada-37xx: add Methode eDPU compatible
  arm64: dts: marvell: split Methode uDPU DTS
  arm64: dts: marvell: rename temp sensor nodes
  arm64: dts: marvell: uDPU: remove LED node pinctrl-names
  arm64: dts: marvell: uDPU: align LED-s with bindings
  arm64: dts: marvell: uDPU: add missing SoC compatible
  arm64: dts: marvell: espressobin-ultra: add generic Espressobin compatible
  dt-bindings: marvell: convert Armada 37xx compatibles to YAML
  dt-bindings: vendor-prefixes: add Methode Electronics
  arm64: dts: marvell: Add UART1-3 for AC5/AC5X

Link: https://lore.kernel.org/r/87h70yxfmy.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

6 files changed, 213 insertions, 159 deletions

diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index b6d493e34dc5..058237681fe5 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -1,6 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 # Mvebu SoC Family
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-eDPU.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-emmc.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-ultra.dtb
diff --git a/arch/arm64/boot/dts/marvell/ac5-98dx25xx.dtsi b/arch/arm64/boot/dts/marvell/ac5-98dx25xx.dtsi
index 80b44c7df56a..44ed6f963b75 100644
--- a/arch/arm64/boot/dts/marvell/ac5-98dx25xx.dtsi
+++ b/arch/arm64/boot/dts/marvell/ac5-98dx25xx.dtsi
@@ -95,6 +95,36 @@
 				status = "okay";
 			};
 
+			uart1: serial@12100 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x11000 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				clocks = <&cnm_clock>;
+				status = "disabled";
+			};
+
+			uart2: serial@12200 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12200 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				clocks = <&cnm_clock>;
+				status = "disabled";
+			};
+
+			uart3: serial@12300 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12300 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				clocks = <&cnm_clock>;
+				status = "disabled";
+			};
+
 			mdio: mdio@22004 {
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -117,8 +147,8 @@
 				pinctrl-names = "default", "gpio";
 				pinctrl-0 = <&i2c0_pins>;
 				pinctrl-1 = <&i2c0_gpio>;
-				scl_gpio = <&gpio0 26 GPIO_ACTIVE_HIGH>;
-				sda_gpio = <&gpio0 27 GPIO_ACTIVE_HIGH>;
+				scl-gpios = <&gpio0 26 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+				sda-gpios = <&gpio0 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 				status = "disabled";
 			};
 
@@ -136,8 +166,8 @@
 				pinctrl-names = "default", "gpio";
 				pinctrl-0 = <&i2c1_pins>;
 				pinctrl-1 = <&i2c1_gpio>;
-				scl_gpio = <&gpio0 20 GPIO_ACTIVE_HIGH>;
-				sda_gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
+				scl-gpios = <&gpio0 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+				sda-gpios = <&gpio0 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 				status = "disabled";
 			};
 
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-eDPU.dts b/arch/arm64/boot/dts/marvell/armada-3720-eDPU.dts
new file mode 100644
index 000000000000..57fc698e55d0
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-3720-eDPU.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "armada-3720-uDPU.dtsi"
+
+/ {
+	model = "Methode eDPU Board";
+	compatible = "methode,edpu", "marvell,armada3720", "marvell,armada3710";
+};
+
+&eth0 {
+	phy-mode = "2500base-x";
+};
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts b/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
index 070725b81be5..1b2ed63ae6a2 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
@@ -12,8 +12,8 @@
 
 / {
 	model = "Globalscale Marvell ESPRESSOBin Ultra Board";
-	compatible = "globalscale,espressobin-ultra", "marvell,armada3720",
-		     "marvell,armada3710";
+	compatible = "globalscale,espressobin-ultra", "globalscale,espressobin",
+		     "marvell,armada3720", "marvell,armada3710";
 
 	aliases {
 		/* ethernet1 is WAN port */
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
index b20c8e7d923b..c76eceabd33e 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
@@ -1,66 +1,12 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Device tree for the uDPU board.
- * Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
- * Copyright (C) 2016 Marvell
- * Copyright (C) 2019 Methode Electronics
- * Copyright (C) 2019 Telus
- *
- * Vladimir Vid <vladimir.vid@sartura.hr>
- */
 
 /dts-v1/;
 
-#include <dt-bindings/gpio/gpio.h>
-#include "armada-372x.dtsi"
+#include "armada-3720-uDPU.dtsi"
 
 / {
 	model = "Methode uDPU Board";
-	compatible = "methode,udpu", "marvell,armada3720";
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	memory@0 {
-		device_type = "memory";
-		reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
-	};
-
-	leds {
-		pinctrl-names = "default";
-		compatible = "gpio-leds";
-
-		power1 {
-			label = "udpu:green:power";
-			gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
-		};
-
-		power2 {
-			label = "udpu:red:power";
-			gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
-		};
-
-		network1 {
-			label = "udpu:green:network";
-			gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
-		};
-
-		network2 {
-			label = "udpu:red:network";
-			gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
-		};
-
-		alarm1 {
-			label = "udpu:green:alarm";
-			gpios = <&gpionb 15 GPIO_ACTIVE_LOW>;
-		};
-
-		alarm2 {
-			label = "udpu:red:alarm";
-			gpios = <&gpionb 16 GPIO_ACTIVE_LOW>;
-		};
-	};
+	compatible = "methode,udpu", "marvell,armada3720", "marvell,armada3710";
 
 	sfp_eth0: sfp-eth0 {
 		compatible = "sff,sfp";
@@ -71,55 +17,6 @@
 		tx-fault-gpios = <&gpiosb 5 GPIO_ACTIVE_HIGH>;
 		maximum-power-milliwatt = <3000>;
 	};
-
-	sfp_eth1: sfp-eth1 {
-		compatible = "sff,sfp";
-		i2c-bus = <&i2c1>;
-		los-gpios = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios = <&gpiosb 8 GPIO_ACTIVE_LOW>;
-		tx-disable-gpios = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
-		tx-fault-gpios = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
-		maximum-power-milliwatt = <3000>;
-	};
-};
-
-&sdhci0 {
-	status = "okay";
-	bus-width = <8>;
-	mmc-ddr-1_8v;
-	mmc-hs400-1_8v;
-	marvell,pad-type = "fixed-1-8v";
-	non-removable;
-	no-sd;
-	no-sdio;
-};
-
-&spi0 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&spi_quad_pins>;
-
-	flash@0 {
-		compatible = "jedec,spi-nor";
-		reg = <0>;
-		spi-max-frequency = <54000000>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			partition@0 {
-				label = "firmware";
-				reg = <0x0 0x180000>;
-			};
-
-			partition@180000 {
-				label = "u-boot-env";
-				reg = <0x180000 0x10000>;
-			};
-		};
-	};
 };
 
 &pinctrl_nb {
@@ -127,11 +24,6 @@
 		groups = "i2c1";
 		function = "gpio";
 	};
-
-	i2c2_recovery_pins: i2c2-recovery-pins {
-		groups = "i2c2";
-		function = "gpio";
-	};
 };
 
 &i2c0 {
@@ -144,50 +36,7 @@
 	sda-gpios = <&gpionb 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 };
 
-&i2c1 {
-	status = "okay";
-	pinctrl-names = "default", "recovery";
-	pinctrl-0 = <&i2c2_pins>;
-	pinctrl-1 = <&i2c2_recovery_pins>;
-	/delete-property/mrvl,i2c-fast-mode;
-	scl-gpios = <&gpionb 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-	sda-gpios = <&gpionb 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-
-	nct375@48 {
-		status = "okay";
-		compatible = "ti,tmp75c";
-		reg = <0x48>;
-	};
-
-	nct375@49 {
-		status = "okay";
-		compatible = "ti,tmp75c";
-		reg = <0x49>;
-	};
-};
-
 &eth0 {
 	phy-mode = "sgmii";
-	status = "okay";
-	managed = "in-band-status";
-	phys = <&comphy1 0>;
 	sfp = <&sfp_eth0>;
 };
-
-&eth1 {
-	phy-mode = "sgmii";
-	status = "okay";
-	managed = "in-band-status";
-	phys = <&comphy0 1>;
-	sfp = <&sfp_eth1>;
-};
-
-&usb3 {
-	status = "okay";
-	phys = <&usb2_utmi_otg_phy>;
-	phy-names = "usb2-utmi-otg-phy";
-};
-
-&uart0 {
-	status = "okay";
-};
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dtsi b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dtsi
new file mode 100644
index 000000000000..3f79923376fb
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dtsi
@@ -0,0 +1,160 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device tree for the uDPU board.
+ * Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
+ * Copyright (C) 2016 Marvell
+ * Copyright (C) 2019 Methode Electronics
+ * Copyright (C) 2019 Telus
+ *
+ * Vladimir Vid <vladimir.vid@sartura.hr>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-372x.dtsi"
+
+/ {
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power1 {
+			label = "udpu:green:power";
+			gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
+		};
+
+		led-power2 {
+			label = "udpu:red:power";
+			gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
+		};
+
+		led-network1 {
+			label = "udpu:green:network";
+			gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led-network2 {
+			label = "udpu:red:network";
+			gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
+		};
+
+		led-alarm1 {
+			label = "udpu:green:alarm";
+			gpios = <&gpionb 15 GPIO_ACTIVE_LOW>;
+		};
+
+		led-alarm2 {
+			label = "udpu:red:alarm";
+			gpios = <&gpionb 16 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	sfp_eth1: sfp-eth1 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c1>;
+		los-gpio = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>;
+		tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
+		maximum-power-milliwatt = <3000>;
+	};
+};
+
+&sdhci0 {
+	status = "okay";
+	bus-width = <8>;
+	mmc-ddr-1_8v;
+	mmc-hs400-1_8v;
+	marvell,pad-type = "fixed-1-8v";
+	non-removable;
+	no-sd;
+	no-sdio;
+};
+
+&spi0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_quad_pins>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <54000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "firmware";
+				reg = <0x0 0x180000>;
+			};
+
+			partition@180000 {
+				label = "u-boot-env";
+				reg = <0x180000 0x10000>;
+			};
+		};
+	};
+};
+
+&pinctrl_nb {
+	i2c2_recovery_pins: i2c2-recovery-pins {
+		groups = "i2c2";
+		function = "gpio";
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	pinctrl-names = "default", "recovery";
+	pinctrl-0 = <&i2c2_pins>;
+	pinctrl-1 = <&i2c2_recovery_pins>;
+	/delete-property/mrvl,i2c-fast-mode;
+	scl-gpios = <&gpionb 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpionb 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+	temp-sensor@48 {
+		compatible = "ti,tmp75c";
+		reg = <0x48>;
+	};
+
+	temp-sensor@49 {
+		compatible = "ti,tmp75c";
+		reg = <0x49>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	managed = "in-band-status";
+	phys = <&comphy1 0>;
+};
+
+&eth1 {
+	phy-mode = "sgmii";
+	status = "okay";
+	managed = "in-band-status";
+	phys = <&comphy0 1>;
+	sfp = <&sfp_eth1>;
+};
+
+&usb3 {
+	status = "okay";
+	phys = <&usb2_utmi_otg_phy>;
+	phy-names = "usb2-utmi-otg-phy";
+};
+
+&uart0 {
+	status = "okay";
+};