remove the v850 port

Trying to compile the v850 port brings many compile errors, one of them exists
since at least kernel 2.6.19.

There also seems to be noone willing to bring this port back into a usable
state.

This patch therefore removes the v850 port.

If anyone ever decides to revive the v850 port the code will still be
available from older kernels, and it wouldn't be impossible for the port to
reenter the kernel if it would become actively maintained again.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

1 files changed, 0 insertions, 121 deletions

diff --git a/arch/v850/kernel/rte_cb_multi.c b/arch/v850/kernel/rte_cb_multi.c
deleted file mode 100644
index 963d55ab34cc..000000000000
--- a/arch/v850/kernel/rte_cb_multi.c
+++ /dev/null
@@ -1,121 +0,0 @@
-/*
- * include/asm-v850/rte_multi.c -- Support for Multi debugger monitor ROM
- * 	on Midas lab RTE-CB series of evaluation boards
- *
- *  Copyright (C) 2001,02,03  NEC Electronics Corporation
- *  Copyright (C) 2001,02,03  Miles Bader <miles@gnu.org>
- *
- * This file is subject to the terms and conditions of the GNU General
- * Public License.  See the file COPYING in the main directory of this
- * archive for more details.
- *
- * Written by Miles Bader <miles@gnu.org>
- */
-
-#include <linux/init.h>
-
-#include <asm/machdep.h>
-
-#define IRQ_ADDR(irq) (0x80 + (irq) * 0x10)
-
-/* A table of which interrupt vectors to install, since blindly
-   installing all of them makes the debugger stop working.  This is a
-   list of offsets in the interrupt vector area; each entry means to
-   copy that particular 16-byte vector.  An entry less than zero ends
-   the table.  */
-static long multi_intv_install_table[] = {
-	/* Trap vectors */
-	0x40, 0x50,		
-
-#ifdef CONFIG_RTE_CB_MULTI_DBTRAP
-	/* Illegal insn / dbtrap.  These are used by multi, so only handle
-	   them if configured to do so.  */
-	0x60,
-#endif
-
-	/* GINT1 - GINT3 (note, not GINT0!) */
-	IRQ_ADDR (IRQ_GINT(1)),
-	IRQ_ADDR (IRQ_GINT(2)),
-	IRQ_ADDR (IRQ_GINT(3)),
-
-	/* Timer D interrupts (up to 4 timers) */
-	IRQ_ADDR (IRQ_INTCMD(0)),
-#if IRQ_INTCMD_NUM > 1
-	IRQ_ADDR (IRQ_INTCMD(1)),
-#if IRQ_INTCMD_NUM > 2
-	IRQ_ADDR (IRQ_INTCMD(2)),
-#if IRQ_INTCMD_NUM > 3
-	IRQ_ADDR (IRQ_INTCMD(3)),
-#endif
-#endif
-#endif
-	
-	/* UART interrupts (up to 3 channels) */
-	IRQ_ADDR (IRQ_INTSER (0)), /* err */
-	IRQ_ADDR (IRQ_INTSR  (0)), /* rx */
-	IRQ_ADDR (IRQ_INTST  (0)), /* tx */
-#if IRQ_INTSR_NUM > 1
-	IRQ_ADDR (IRQ_INTSER (1)), /* err */
-	IRQ_ADDR (IRQ_INTSR  (1)), /* rx */
-	IRQ_ADDR (IRQ_INTST  (1)), /* tx */
-#if IRQ_INTSR_NUM > 2
-	IRQ_ADDR (IRQ_INTSER (2)), /* err */
-	IRQ_ADDR (IRQ_INTSR  (2)), /* rx */
-	IRQ_ADDR (IRQ_INTST  (2)), /* tx */
-#endif
-#endif
-
-	-1
-};
-
-/* Early initialization for kernel using Multi debugger ROM monitor.  */
-void __init multi_init (void)
-{
-	/* We're using the Multi debugger monitor, so we have to install
-	   the interrupt vectors.  The monitor doesn't allow them to be
-	   initially downloaded into their final destination because
-	   it's in the monitor's scratch-RAM area.  Unfortunately, Multi
-	   also doesn't deal correctly with ELF sections where the LMA
-	   and VMA differ -- it just ignores the LMA -- so we can't use
-	   that feature to work around the problem.  What we do instead
-	   is just put the interrupt vectors into a normal section, and
-	   do the necessary copying and relocation here.  Since the
-	   interrupt vector basically only contains `jr' instructions
-	   and no-ops, it's not that hard.  */
-	extern unsigned long _intv_load_start, _intv_start;
-	register unsigned long *src = &_intv_load_start;
-	register unsigned long *dst = (unsigned long *)INTV_BASE;
-	register unsigned long jr_fixup = (char *)&_intv_start - (char *)dst;
-	register long *ii;
-
-	/* Copy interrupt vectors as instructed by multi_intv_install_table. */
-	for (ii = multi_intv_install_table; *ii >= 0; ii++) {
-		/* Copy 16-byte interrupt vector at offset *ii.  */
-		int boffs;
-		for (boffs = 0; boffs < 0x10; boffs += sizeof *src) {
-			/* Copy a single word, fixing up the jump offs
-			   if it's a `jr' instruction.  */
-			int woffs = (*ii + boffs) / sizeof *src;
-			unsigned long word = src[woffs];
-
-			if ((word & 0xFC0) == 0x780) {
-				/* A `jr' insn, fix up its offset (and yes, the
-				   weird half-word swapping is intentional). */
-				unsigned short hi = word & 0xFFFF;
-				unsigned short lo = word >> 16;
-				unsigned long udisp22
-					= lo + ((hi & 0x3F) << 16);
-				long disp22 = (long)(udisp22 << 10) >> 10;
-
-				disp22 += jr_fixup;
-
-				hi = ((disp22 >> 16) & 0x3F) | 0x780;
-				lo = disp22 & 0xFFFF;
-
-				word = hi + (lo << 16);
-			}
-
-			dst[woffs] = word;
-		}
-	}
-}