Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux

Pull clk updates from Stephen Boyd:
 "This is all driver updates, the majority of which is a bunch of new
  Qualcomm clk drivers that dominate the diffstat because we add support
  for six SoCs from that particular vendor.

  The other big change is the removal of various clk drivers that are no
  longer used now that the kernel is dropping support for those SoCs.

  Beyond that there's the usual non-critical fixes for existing drivers
  and a good number of patches from Lee Jones that cleanup a bunch of
  W=1 enabled builds.

  Removed Drivers:
   - Remove efm32 clk driver
   - Remove tango4 clk driver
   - Remove zte zx clk driver
   - Remove sirf prima2/atlast clk drivers
   - Remove u300 clk driver

  New Drivers:
   - PLL support on MStar/SigmaStar ARMv7 SoCs
   - CPU clks for Qualcomm SDX55
   - GCC and RPMh clks for Qualcomm SC8180x and SC7280 SoCs
   - GCC clks for Qualcomm SM8350
   - GPU clks for Qualcomm SDM660/SDM630

  Updates:
   - Video clk fixups on Qualcomm SM8250
   - Improvements for multimedia clks on Qualcomm MSM8998
   - Fix many warnings with W=1 enabled builds under drivers/clk/
   - Support crystal load capacitance for Versaclock VC5
   - Add a "skip recall" DT binding for Silicon Labs' si570 to avoid
     glitches at boot
   - Convert Xilinx VCU clk driver to a proper clk provider driver
   - Expose Xilinx ZynqMP clk driver to more platforms
   - Amlogic pll driver fixup
   - Amlogic meson8b clock controller dt support clean up
   - Remove mipi clk from the Amlogic axg clock controller
   - New Rockchip rk3368 clock ids related to camera input
   - Use pr_notice() instead of pr_warn() on i.MX6Q pre-boot ldb_di_clk
     reparenting
   - A series from Liu Ying that adds some SCU clocks support for
     i.MX8qxp DC0/MIPI-LVDS subsystems
   - A series from Lucas Stach that adds PLL monitor clocks for i.MX8MQ,
     and clkout1/2 support for i.MX8MM/MN
   - Add I2c and Ethernet (RAVB) clocks on Renesas R-Car V3U
   - Add timer (TMU) clocks on most Renesas R-Car Gen3 SoCs
   - Add video-related (FCPVD/VSPD/VSPX), watchdog (RWDT), serial
     (HSCIF), pincontrol/GPIO (PFC/GPIO), SPI (MSIOF), SDHI, and DMA
     (SYS-DMAC) clocks on Renesas R-Car V3U
   - Add support for the USB 2.0 clock selector on Renesas RZ/G2 SoCs
   - Allwinner H616 SoC clk support"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (171 commits)
  clk: mstar: msc313-mpll: Fix format specifier
  clk: mstar: Allow MStar clk drivers to be compile tested
  clk: qoriq: use macros to generate pll_mask
  clk: qcom: Add Global Clock controller (GCC) driver for SC7280
  dt-bindings: clock: Add SC7280 GCC clock binding
  clk: qcom: rpmh: Add support for RPMH clocks on SC7280
  dt-bindings: clock: Add RPMHCC bindings for SC7280
  clk: qcom: gcc-sm8350: add gdsc
  dt-bindings: clock: Add QCOM SDM630 and SDM660 graphics clock bindings
  clk: qcom: Add SDM660 GPU Clock Controller (GPUCC) driver
  clk: qcom: mmcc-msm8996: Migrate gfx3d clock to clk_rcg2_gfx3d
  clk: qcom: rcg2: Stop hardcoding gfx3d pingpong parent numbers
  dt-bindings: clock: Add support for the SDM630 and SDM660 mmcc
  clk: qcom: Add SDM660 Multimedia Clock Controller (MMCC) driver
  clk: qcom: gcc-sdm660: Mark GPU CFG AHB clock as critical
  clk: qcom: gcc-sdm660: Mark MMSS NoC CFG AHB clock as critical
  clk: qcom: gpucc-msm8998: Allow fabia gpupll0 rate setting
  clk: qcom: gpucc-msm8998: Add resets, cxc, fix flags on gpu_gx_gdsc
  clk: qcom: gdsc: Implement NO_RET_PERIPH flag
  clk: mstar: MStar/SigmaStar MPLL driver
  ...

1 files changed, 0 insertions, 1199 deletions

diff --git a/drivers/clk/clk-u300.c b/drivers/clk/clk-u300.c
deleted file mode 100644
index e228c07c4c6e..000000000000
--- a/drivers/clk/clk-u300.c
+++ /dev/null
@@ -1,1199 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * U300 clock implementation
- * Copyright (C) 2007-2012 ST-Ericsson AB
- * Author: Linus Walleij <linus.walleij@stericsson.com>
- * Author: Jonas Aaberg <jonas.aberg@stericsson.com>
- */
-#include <linux/clkdev.h>
-#include <linux/slab.h>
-#include <linux/err.h>
-#include <linux/io.h>
-#include <linux/clk-provider.h>
-#include <linux/spinlock.h>
-#include <linux/of.h>
-#include <linux/platform_data/clk-u300.h>
-
-/* APP side SYSCON registers */
-/* CLK Control Register 16bit (R/W) */
-#define U300_SYSCON_CCR						(0x0000)
-#define U300_SYSCON_CCR_I2S1_USE_VCXO				(0x0040)
-#define U300_SYSCON_CCR_I2S0_USE_VCXO				(0x0020)
-#define U300_SYSCON_CCR_TURN_VCXO_ON				(0x0008)
-#define U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK			(0x0007)
-#define U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER		(0x04)
-#define U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW			(0x03)
-#define U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE		(0x02)
-#define U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH			(0x01)
-#define U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST			(0x00)
-/* CLK Status Register 16bit (R/W) */
-#define U300_SYSCON_CSR						(0x0004)
-#define U300_SYSCON_CSR_PLL208_LOCK_IND				(0x0002)
-#define U300_SYSCON_CSR_PLL13_LOCK_IND				(0x0001)
-/* Reset lines for SLOW devices 16bit (R/W) */
-#define U300_SYSCON_RSR						(0x0014)
-#define U300_SYSCON_RSR_PPM_RESET_EN				(0x0200)
-#define U300_SYSCON_RSR_ACC_TMR_RESET_EN			(0x0100)
-#define U300_SYSCON_RSR_APP_TMR_RESET_EN			(0x0080)
-#define U300_SYSCON_RSR_RTC_RESET_EN				(0x0040)
-#define U300_SYSCON_RSR_KEYPAD_RESET_EN				(0x0020)
-#define U300_SYSCON_RSR_GPIO_RESET_EN				(0x0010)
-#define U300_SYSCON_RSR_EH_RESET_EN				(0x0008)
-#define U300_SYSCON_RSR_BTR_RESET_EN				(0x0004)
-#define U300_SYSCON_RSR_UART_RESET_EN				(0x0002)
-#define U300_SYSCON_RSR_SLOW_BRIDGE_RESET_EN			(0x0001)
-/* Reset lines for FAST devices 16bit (R/W) */
-#define U300_SYSCON_RFR						(0x0018)
-#define U300_SYSCON_RFR_UART1_RESET_ENABLE			(0x0080)
-#define U300_SYSCON_RFR_SPI_RESET_ENABLE			(0x0040)
-#define U300_SYSCON_RFR_MMC_RESET_ENABLE			(0x0020)
-#define U300_SYSCON_RFR_PCM_I2S1_RESET_ENABLE			(0x0010)
-#define U300_SYSCON_RFR_PCM_I2S0_RESET_ENABLE			(0x0008)
-#define U300_SYSCON_RFR_I2C1_RESET_ENABLE			(0x0004)
-#define U300_SYSCON_RFR_I2C0_RESET_ENABLE			(0x0002)
-#define U300_SYSCON_RFR_FAST_BRIDGE_RESET_ENABLE		(0x0001)
-/* Reset lines for the rest of the peripherals 16bit (R/W) */
-#define U300_SYSCON_RRR						(0x001c)
-#define U300_SYSCON_RRR_CDS_RESET_EN				(0x4000)
-#define U300_SYSCON_RRR_ISP_RESET_EN				(0x2000)
-#define U300_SYSCON_RRR_INTCON_RESET_EN				(0x1000)
-#define U300_SYSCON_RRR_MSPRO_RESET_EN				(0x0800)
-#define U300_SYSCON_RRR_XGAM_RESET_EN				(0x0100)
-#define U300_SYSCON_RRR_XGAM_VC_SYNC_RESET_EN			(0x0080)
-#define U300_SYSCON_RRR_NANDIF_RESET_EN				(0x0040)
-#define U300_SYSCON_RRR_EMIF_RESET_EN				(0x0020)
-#define U300_SYSCON_RRR_DMAC_RESET_EN				(0x0010)
-#define U300_SYSCON_RRR_CPU_RESET_EN				(0x0008)
-#define U300_SYSCON_RRR_APEX_RESET_EN				(0x0004)
-#define U300_SYSCON_RRR_AHB_RESET_EN				(0x0002)
-#define U300_SYSCON_RRR_AAIF_RESET_EN				(0x0001)
-/* Clock enable for SLOW peripherals 16bit (R/W) */
-#define U300_SYSCON_CESR					(0x0020)
-#define U300_SYSCON_CESR_PPM_CLK_EN				(0x0200)
-#define U300_SYSCON_CESR_ACC_TMR_CLK_EN				(0x0100)
-#define U300_SYSCON_CESR_APP_TMR_CLK_EN				(0x0080)
-#define U300_SYSCON_CESR_KEYPAD_CLK_EN				(0x0040)
-#define U300_SYSCON_CESR_GPIO_CLK_EN				(0x0010)
-#define U300_SYSCON_CESR_EH_CLK_EN				(0x0008)
-#define U300_SYSCON_CESR_BTR_CLK_EN				(0x0004)
-#define U300_SYSCON_CESR_UART_CLK_EN				(0x0002)
-#define U300_SYSCON_CESR_SLOW_BRIDGE_CLK_EN			(0x0001)
-/* Clock enable for FAST peripherals 16bit (R/W) */
-#define U300_SYSCON_CEFR					(0x0024)
-#define U300_SYSCON_CEFR_UART1_CLK_EN				(0x0200)
-#define U300_SYSCON_CEFR_I2S1_CORE_CLK_EN			(0x0100)
-#define U300_SYSCON_CEFR_I2S0_CORE_CLK_EN			(0x0080)
-#define U300_SYSCON_CEFR_SPI_CLK_EN				(0x0040)
-#define U300_SYSCON_CEFR_MMC_CLK_EN				(0x0020)
-#define U300_SYSCON_CEFR_I2S1_CLK_EN				(0x0010)
-#define U300_SYSCON_CEFR_I2S0_CLK_EN				(0x0008)
-#define U300_SYSCON_CEFR_I2C1_CLK_EN				(0x0004)
-#define U300_SYSCON_CEFR_I2C0_CLK_EN				(0x0002)
-#define U300_SYSCON_CEFR_FAST_BRIDGE_CLK_EN			(0x0001)
-/* Clock enable for the rest of the peripherals 16bit (R/W) */
-#define U300_SYSCON_CERR					(0x0028)
-#define U300_SYSCON_CERR_CDS_CLK_EN				(0x2000)
-#define U300_SYSCON_CERR_ISP_CLK_EN				(0x1000)
-#define U300_SYSCON_CERR_MSPRO_CLK_EN				(0x0800)
-#define U300_SYSCON_CERR_AHB_SUBSYS_BRIDGE_CLK_EN		(0x0400)
-#define U300_SYSCON_CERR_SEMI_CLK_EN				(0x0200)
-#define U300_SYSCON_CERR_XGAM_CLK_EN				(0x0100)
-#define U300_SYSCON_CERR_VIDEO_ENC_CLK_EN			(0x0080)
-#define U300_SYSCON_CERR_NANDIF_CLK_EN				(0x0040)
-#define U300_SYSCON_CERR_EMIF_CLK_EN				(0x0020)
-#define U300_SYSCON_CERR_DMAC_CLK_EN				(0x0010)
-#define U300_SYSCON_CERR_CPU_CLK_EN				(0x0008)
-#define U300_SYSCON_CERR_APEX_CLK_EN				(0x0004)
-#define U300_SYSCON_CERR_AHB_CLK_EN				(0x0002)
-#define U300_SYSCON_CERR_AAIF_CLK_EN				(0x0001)
-/* Single block clock enable 16bit (-/W) */
-#define U300_SYSCON_SBCER					(0x002c)
-#define U300_SYSCON_SBCER_PPM_CLK_EN				(0x0009)
-#define U300_SYSCON_SBCER_ACC_TMR_CLK_EN			(0x0008)
-#define U300_SYSCON_SBCER_APP_TMR_CLK_EN			(0x0007)
-#define U300_SYSCON_SBCER_KEYPAD_CLK_EN				(0x0006)
-#define U300_SYSCON_SBCER_GPIO_CLK_EN				(0x0004)
-#define U300_SYSCON_SBCER_EH_CLK_EN				(0x0003)
-#define U300_SYSCON_SBCER_BTR_CLK_EN				(0x0002)
-#define U300_SYSCON_SBCER_UART_CLK_EN				(0x0001)
-#define U300_SYSCON_SBCER_SLOW_BRIDGE_CLK_EN			(0x0000)
-#define U300_SYSCON_SBCER_UART1_CLK_EN				(0x0019)
-#define U300_SYSCON_SBCER_I2S1_CORE_CLK_EN			(0x0018)
-#define U300_SYSCON_SBCER_I2S0_CORE_CLK_EN			(0x0017)
-#define U300_SYSCON_SBCER_SPI_CLK_EN				(0x0016)
-#define U300_SYSCON_SBCER_MMC_CLK_EN				(0x0015)
-#define U300_SYSCON_SBCER_I2S1_CLK_EN				(0x0014)
-#define U300_SYSCON_SBCER_I2S0_CLK_EN				(0x0013)
-#define U300_SYSCON_SBCER_I2C1_CLK_EN				(0x0012)
-#define U300_SYSCON_SBCER_I2C0_CLK_EN				(0x0011)
-#define U300_SYSCON_SBCER_FAST_BRIDGE_CLK_EN			(0x0010)
-#define U300_SYSCON_SBCER_CDS_CLK_EN				(0x002D)
-#define U300_SYSCON_SBCER_ISP_CLK_EN				(0x002C)
-#define U300_SYSCON_SBCER_MSPRO_CLK_EN				(0x002B)
-#define U300_SYSCON_SBCER_AHB_SUBSYS_BRIDGE_CLK_EN		(0x002A)
-#define U300_SYSCON_SBCER_SEMI_CLK_EN				(0x0029)
-#define U300_SYSCON_SBCER_XGAM_CLK_EN				(0x0028)
-#define U300_SYSCON_SBCER_VIDEO_ENC_CLK_EN			(0x0027)
-#define U300_SYSCON_SBCER_NANDIF_CLK_EN				(0x0026)
-#define U300_SYSCON_SBCER_EMIF_CLK_EN				(0x0025)
-#define U300_SYSCON_SBCER_DMAC_CLK_EN				(0x0024)
-#define U300_SYSCON_SBCER_CPU_CLK_EN				(0x0023)
-#define U300_SYSCON_SBCER_APEX_CLK_EN				(0x0022)
-#define U300_SYSCON_SBCER_AHB_CLK_EN				(0x0021)
-#define U300_SYSCON_SBCER_AAIF_CLK_EN				(0x0020)
-/* Single block clock disable 16bit (-/W) */
-#define U300_SYSCON_SBCDR					(0x0030)
-/* Same values as above for SBCER */
-/* Clock force SLOW peripherals 16bit (R/W) */
-#define U300_SYSCON_CFSR					(0x003c)
-#define U300_SYSCON_CFSR_PPM_CLK_FORCE_EN			(0x0200)
-#define U300_SYSCON_CFSR_ACC_TMR_CLK_FORCE_EN			(0x0100)
-#define U300_SYSCON_CFSR_APP_TMR_CLK_FORCE_EN			(0x0080)
-#define U300_SYSCON_CFSR_KEYPAD_CLK_FORCE_EN			(0x0020)
-#define U300_SYSCON_CFSR_GPIO_CLK_FORCE_EN			(0x0010)
-#define U300_SYSCON_CFSR_EH_CLK_FORCE_EN			(0x0008)
-#define U300_SYSCON_CFSR_BTR_CLK_FORCE_EN			(0x0004)
-#define U300_SYSCON_CFSR_UART_CLK_FORCE_EN			(0x0002)
-#define U300_SYSCON_CFSR_SLOW_BRIDGE_CLK_FORCE_EN		(0x0001)
-/* Clock force FAST peripherals 16bit (R/W) */
-#define U300_SYSCON_CFFR					(0x40)
-/* Values not defined. Define if you want to use them. */
-/* Clock force the rest of the peripherals 16bit (R/W) */
-#define U300_SYSCON_CFRR					(0x44)
-#define U300_SYSCON_CFRR_CDS_CLK_FORCE_EN			(0x2000)
-#define U300_SYSCON_CFRR_ISP_CLK_FORCE_EN			(0x1000)
-#define U300_SYSCON_CFRR_MSPRO_CLK_FORCE_EN			(0x0800)
-#define U300_SYSCON_CFRR_AHB_SUBSYS_BRIDGE_CLK_FORCE_EN		(0x0400)
-#define U300_SYSCON_CFRR_SEMI_CLK_FORCE_EN			(0x0200)
-#define U300_SYSCON_CFRR_XGAM_CLK_FORCE_EN			(0x0100)
-#define U300_SYSCON_CFRR_VIDEO_ENC_CLK_FORCE_EN			(0x0080)
-#define U300_SYSCON_CFRR_NANDIF_CLK_FORCE_EN			(0x0040)
-#define U300_SYSCON_CFRR_EMIF_CLK_FORCE_EN			(0x0020)
-#define U300_SYSCON_CFRR_DMAC_CLK_FORCE_EN			(0x0010)
-#define U300_SYSCON_CFRR_CPU_CLK_FORCE_EN			(0x0008)
-#define U300_SYSCON_CFRR_APEX_CLK_FORCE_EN			(0x0004)
-#define U300_SYSCON_CFRR_AHB_CLK_FORCE_EN			(0x0002)
-#define U300_SYSCON_CFRR_AAIF_CLK_FORCE_EN			(0x0001)
-/* PLL208 Frequency Control 16bit (R/W) */
-#define U300_SYSCON_PFCR					(0x48)
-#define U300_SYSCON_PFCR_DPLL_MULT_NUM				(0x000F)
-/* Power Management Control 16bit (R/W) */
-#define U300_SYSCON_PMCR					(0x50)
-#define U300_SYSCON_PMCR_DCON_ENABLE				(0x0002)
-#define U300_SYSCON_PMCR_PWR_MGNT_ENABLE			(0x0001)
-/* Reset Out 16bit (R/W) */
-#define U300_SYSCON_RCR						(0x6c)
-#define U300_SYSCON_RCR_RESOUT0_RST_N_DISABLE			(0x0001)
-/* EMIF Slew Rate Control 16bit (R/W) */
-#define U300_SYSCON_SRCLR					(0x70)
-#define U300_SYSCON_SRCLR_MASK					(0x03FF)
-#define U300_SYSCON_SRCLR_VALUE					(0x03FF)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_5_B			(0x0200)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_5_A			(0x0100)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_4_B			(0x0080)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_4_A			(0x0040)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_3_B			(0x0020)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_3_A			(0x0010)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_2_B			(0x0008)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_2_A			(0x0004)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_1_B			(0x0002)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_1_A			(0x0001)
-/* EMIF Clock Control Register 16bit (R/W) */
-#define U300_SYSCON_ECCR					(0x0078)
-#define U300_SYSCON_ECCR_MASK					(0x000F)
-#define U300_SYSCON_ECCR_EMIF_1_STATIC_CLK_EN_N_DISABLE		(0x0008)
-#define U300_SYSCON_ECCR_EMIF_1_RET_OUT_CLK_EN_N_DISABLE	(0x0004)
-#define U300_SYSCON_ECCR_EMIF_MEMCLK_RET_EN_N_DISABLE		(0x0002)
-#define U300_SYSCON_ECCR_EMIF_SDRCLK_RET_EN_N_DISABLE		(0x0001)
-/* MMC/MSPRO frequency divider register 0 16bit (R/W) */
-#define U300_SYSCON_MMF0R					(0x90)
-#define U300_SYSCON_MMF0R_MASK					(0x00FF)
-#define U300_SYSCON_MMF0R_FREQ_0_HIGH_MASK			(0x00F0)
-#define U300_SYSCON_MMF0R_FREQ_0_LOW_MASK			(0x000F)
-/* MMC/MSPRO frequency divider register 1 16bit (R/W) */
-#define U300_SYSCON_MMF1R					(0x94)
-#define U300_SYSCON_MMF1R_MASK					(0x00FF)
-#define U300_SYSCON_MMF1R_FREQ_1_HIGH_MASK			(0x00F0)
-#define U300_SYSCON_MMF1R_FREQ_1_LOW_MASK			(0x000F)
-/* Clock control for the MMC and MSPRO blocks 16bit (R/W) */
-#define U300_SYSCON_MMCR					(0x9C)
-#define U300_SYSCON_MMCR_MASK					(0x0003)
-#define U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE			(0x0002)
-#define U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE			(0x0001)
-/* SYS_0_CLK_CONTROL first clock control 16bit (R/W) */
-#define U300_SYSCON_S0CCR					(0x120)
-#define U300_SYSCON_S0CCR_FIELD_MASK				(0x43FF)
-#define U300_SYSCON_S0CCR_CLOCK_REQ				(0x4000)
-#define U300_SYSCON_S0CCR_CLOCK_REQ_MONITOR			(0x2000)
-#define U300_SYSCON_S0CCR_CLOCK_INV				(0x0200)
-#define U300_SYSCON_S0CCR_CLOCK_FREQ_MASK			(0x01E0)
-#define U300_SYSCON_S0CCR_CLOCK_SELECT_MASK			(0x001E)
-#define U300_SYSCON_S0CCR_CLOCK_ENABLE				(0x0001)
-#define U300_SYSCON_S0CCR_SEL_MCLK				(0x8 << 1)
-#define U300_SYSCON_S0CCR_SEL_ACC_FSM_CLK			(0xA << 1)
-#define U300_SYSCON_S0CCR_SEL_PLL60_48_CLK			(0xC << 1)
-#define U300_SYSCON_S0CCR_SEL_PLL60_60_CLK			(0xD << 1)
-#define U300_SYSCON_S0CCR_SEL_ACC_PLL208_CLK			(0xE << 1)
-#define U300_SYSCON_S0CCR_SEL_APP_PLL13_CLK			(0x0 << 1)
-#define U300_SYSCON_S0CCR_SEL_APP_FSM_CLK			(0x2 << 1)
-#define U300_SYSCON_S0CCR_SEL_RTC_CLK				(0x4 << 1)
-#define U300_SYSCON_S0CCR_SEL_APP_PLL208_CLK			(0x6 << 1)
-/* SYS_1_CLK_CONTROL second clock control 16 bit (R/W) */
-#define U300_SYSCON_S1CCR					(0x124)
-#define U300_SYSCON_S1CCR_FIELD_MASK				(0x43FF)
-#define U300_SYSCON_S1CCR_CLOCK_REQ				(0x4000)
-#define U300_SYSCON_S1CCR_CLOCK_REQ_MONITOR			(0x2000)
-#define U300_SYSCON_S1CCR_CLOCK_INV				(0x0200)
-#define U300_SYSCON_S1CCR_CLOCK_FREQ_MASK			(0x01E0)
-#define U300_SYSCON_S1CCR_CLOCK_SELECT_MASK			(0x001E)
-#define U300_SYSCON_S1CCR_CLOCK_ENABLE				(0x0001)
-#define U300_SYSCON_S1CCR_SEL_MCLK				(0x8 << 1)
-#define U300_SYSCON_S1CCR_SEL_ACC_FSM_CLK			(0xA << 1)
-#define U300_SYSCON_S1CCR_SEL_PLL60_48_CLK			(0xC << 1)
-#define U300_SYSCON_S1CCR_SEL_PLL60_60_CLK			(0xD << 1)
-#define U300_SYSCON_S1CCR_SEL_ACC_PLL208_CLK			(0xE << 1)
-#define U300_SYSCON_S1CCR_SEL_ACC_PLL13_CLK			(0x0 << 1)
-#define U300_SYSCON_S1CCR_SEL_APP_FSM_CLK			(0x2 << 1)
-#define U300_SYSCON_S1CCR_SEL_RTC_CLK				(0x4 << 1)
-#define U300_SYSCON_S1CCR_SEL_APP_PLL208_CLK			(0x6 << 1)
-/* SYS_2_CLK_CONTROL third clock control 16 bit (R/W) */
-#define U300_SYSCON_S2CCR					(0x128)
-#define U300_SYSCON_S2CCR_FIELD_MASK				(0xC3FF)
-#define U300_SYSCON_S2CCR_CLK_STEAL				(0x8000)
-#define U300_SYSCON_S2CCR_CLOCK_REQ				(0x4000)
-#define U300_SYSCON_S2CCR_CLOCK_REQ_MONITOR			(0x2000)
-#define U300_SYSCON_S2CCR_CLOCK_INV				(0x0200)
-#define U300_SYSCON_S2CCR_CLOCK_FREQ_MASK			(0x01E0)
-#define U300_SYSCON_S2CCR_CLOCK_SELECT_MASK			(0x001E)
-#define U300_SYSCON_S2CCR_CLOCK_ENABLE				(0x0001)
-#define U300_SYSCON_S2CCR_SEL_MCLK				(0x8 << 1)
-#define U300_SYSCON_S2CCR_SEL_ACC_FSM_CLK			(0xA << 1)
-#define U300_SYSCON_S2CCR_SEL_PLL60_48_CLK			(0xC << 1)
-#define U300_SYSCON_S2CCR_SEL_PLL60_60_CLK			(0xD << 1)
-#define U300_SYSCON_S2CCR_SEL_ACC_PLL208_CLK			(0xE << 1)
-#define U300_SYSCON_S2CCR_SEL_ACC_PLL13_CLK			(0x0 << 1)
-#define U300_SYSCON_S2CCR_SEL_APP_FSM_CLK			(0x2 << 1)
-#define U300_SYSCON_S2CCR_SEL_RTC_CLK				(0x4 << 1)
-#define U300_SYSCON_S2CCR_SEL_APP_PLL208_CLK			(0x6 << 1)
-/* SC_PLL_IRQ_CONTROL 16bit (R/W) */
-#define U300_SYSCON_PICR					(0x0130)
-#define U300_SYSCON_PICR_MASK					(0x00FF)
-#define U300_SYSCON_PICR_FORCE_PLL208_LOCK_LOW_ENABLE		(0x0080)
-#define U300_SYSCON_PICR_FORCE_PLL208_LOCK_HIGH_ENABLE		(0x0040)
-#define U300_SYSCON_PICR_FORCE_PLL13_LOCK_LOW_ENABLE		(0x0020)
-#define U300_SYSCON_PICR_FORCE_PLL13_LOCK_HIGH_ENABLE		(0x0010)
-#define U300_SYSCON_PICR_IRQMASK_PLL13_UNLOCK_ENABLE		(0x0008)
-#define U300_SYSCON_PICR_IRQMASK_PLL13_LOCK_ENABLE		(0x0004)
-#define U300_SYSCON_PICR_IRQMASK_PLL208_UNLOCK_ENABLE		(0x0002)
-#define U300_SYSCON_PICR_IRQMASK_PLL208_LOCK_ENABLE		(0x0001)
-/* SC_PLL_IRQ_STATUS 16 bit (R/-) */
-#define U300_SYSCON_PISR					(0x0134)
-#define U300_SYSCON_PISR_MASK					(0x000F)
-#define U300_SYSCON_PISR_PLL13_UNLOCK_IND			(0x0008)
-#define U300_SYSCON_PISR_PLL13_LOCK_IND				(0x0004)
-#define U300_SYSCON_PISR_PLL208_UNLOCK_IND			(0x0002)
-#define U300_SYSCON_PISR_PLL208_LOCK_IND			(0x0001)
-/* SC_PLL_IRQ_CLEAR 16 bit (-/W) */
-#define U300_SYSCON_PICLR					(0x0138)
-#define U300_SYSCON_PICLR_MASK					(0x000F)
-#define U300_SYSCON_PICLR_RWMASK				(0x0000)
-#define U300_SYSCON_PICLR_PLL13_UNLOCK_SC			(0x0008)
-#define U300_SYSCON_PICLR_PLL13_LOCK_SC				(0x0004)
-#define U300_SYSCON_PICLR_PLL208_UNLOCK_SC			(0x0002)
-#define U300_SYSCON_PICLR_PLL208_LOCK_SC			(0x0001)
-/* Clock activity observability register 0 */
-#define U300_SYSCON_C0OAR					(0x140)
-#define U300_SYSCON_C0OAR_MASK					(0xFFFF)
-#define U300_SYSCON_C0OAR_VALUE					(0xFFFF)
-#define U300_SYSCON_C0OAR_BT_H_CLK				(0x8000)
-#define U300_SYSCON_C0OAR_ASPB_P_CLK				(0x4000)
-#define U300_SYSCON_C0OAR_APP_SEMI_H_CLK			(0x2000)
-#define U300_SYSCON_C0OAR_APP_SEMI_CLK				(0x1000)
-#define U300_SYSCON_C0OAR_APP_MMC_MSPRO_CLK			(0x0800)
-#define U300_SYSCON_C0OAR_APP_I2S1_CLK				(0x0400)
-#define U300_SYSCON_C0OAR_APP_I2S0_CLK				(0x0200)
-#define U300_SYSCON_C0OAR_APP_CPU_CLK				(0x0100)
-#define U300_SYSCON_C0OAR_APP_52_CLK				(0x0080)
-#define U300_SYSCON_C0OAR_APP_208_CLK				(0x0040)
-#define U300_SYSCON_C0OAR_APP_104_CLK				(0x0020)
-#define U300_SYSCON_C0OAR_APEX_CLK				(0x0010)
-#define U300_SYSCON_C0OAR_AHPB_M_H_CLK				(0x0008)
-#define U300_SYSCON_C0OAR_AHB_CLK				(0x0004)
-#define U300_SYSCON_C0OAR_AFPB_P_CLK				(0x0002)
-#define U300_SYSCON_C0OAR_AAIF_CLK				(0x0001)
-/* Clock activity observability register 1 */
-#define U300_SYSCON_C1OAR					(0x144)
-#define U300_SYSCON_C1OAR_MASK					(0x3FFE)
-#define U300_SYSCON_C1OAR_VALUE					(0x3FFE)
-#define U300_SYSCON_C1OAR_NFIF_F_CLK				(0x2000)
-#define U300_SYSCON_C1OAR_MSPRO_CLK				(0x1000)
-#define U300_SYSCON_C1OAR_MMC_P_CLK				(0x0800)
-#define U300_SYSCON_C1OAR_MMC_CLK				(0x0400)
-#define U300_SYSCON_C1OAR_KP_P_CLK				(0x0200)
-#define U300_SYSCON_C1OAR_I2C1_P_CLK				(0x0100)
-#define U300_SYSCON_C1OAR_I2C0_P_CLK				(0x0080)
-#define U300_SYSCON_C1OAR_GPIO_CLK				(0x0040)
-#define U300_SYSCON_C1OAR_EMIF_MPMC_CLK				(0x0020)
-#define U300_SYSCON_C1OAR_EMIF_H_CLK				(0x0010)
-#define U300_SYSCON_C1OAR_EVHIST_CLK				(0x0008)
-#define U300_SYSCON_C1OAR_PPM_CLK				(0x0004)
-#define U300_SYSCON_C1OAR_DMA_CLK				(0x0002)
-/* Clock activity observability register 2 */
-#define U300_SYSCON_C2OAR					(0x148)
-#define U300_SYSCON_C2OAR_MASK					(0x0FFF)
-#define U300_SYSCON_C2OAR_VALUE					(0x0FFF)
-#define U300_SYSCON_C2OAR_XGAM_CDI_CLK				(0x0800)
-#define U300_SYSCON_C2OAR_XGAM_CLK				(0x0400)
-#define U300_SYSCON_C2OAR_VC_H_CLK				(0x0200)
-#define U300_SYSCON_C2OAR_VC_CLK				(0x0100)
-#define U300_SYSCON_C2OAR_UA_P_CLK				(0x0080)
-#define U300_SYSCON_C2OAR_TMR1_CLK				(0x0040)
-#define U300_SYSCON_C2OAR_TMR0_CLK				(0x0020)
-#define U300_SYSCON_C2OAR_SPI_P_CLK				(0x0010)
-#define U300_SYSCON_C2OAR_PCM_I2S1_CORE_CLK			(0x0008)
-#define U300_SYSCON_C2OAR_PCM_I2S1_CLK				(0x0004)
-#define U300_SYSCON_C2OAR_PCM_I2S0_CORE_CLK			(0x0002)
-#define U300_SYSCON_C2OAR_PCM_I2S0_CLK				(0x0001)
-
-
-/*
- * The clocking hierarchy currently looks like this.
- * NOTE: the idea is NOT to show how the clocks are routed on the chip!
- * The ideas is to show dependencies, so a clock higher up in the
- * hierarchy has to be on in order for another clock to be on. Now,
- * both CPU and DMA can actually be on top of the hierarchy, and that
- * is not modeled currently. Instead we have the backbone AMBA bus on
- * top. This bus cannot be programmed in any way but conceptually it
- * needs to be active for the bridges and devices to transport data.
- *
- * Please be aware that a few clocks are hw controlled, which mean that
- * the hw itself can turn on/off or change the rate of the clock when
- * needed!
- *
- *  AMBA bus
- *  |
- *  +- CPU
- *  +- FSMC NANDIF NAND Flash interface
- *  +- SEMI Shared Memory interface
- *  +- ISP Image Signal Processor (U335 only)
- *  +- CDS (U335 only)
- *  +- DMA Direct Memory Access Controller
- *  +- AAIF APP/ACC Interface (Mobile Scalable Link, MSL)
- *  +- APEX
- *  +- VIDEO_ENC AVE2/3 Video Encoder
- *  +- XGAM Graphics Accelerator Controller
- *  +- AHB
- *  |
- *  +- ahb:0 AHB Bridge
- *  |  |
- *  |  +- ahb:1 INTCON Interrupt controller
- *  |  +- ahb:3 MSPRO  Memory Stick Pro controller
- *  |  +- ahb:4 EMIF   External Memory interface
- *  |
- *  +- fast:0 FAST bridge
- *  |  |
- *  |  +- fast:1 MMCSD MMC/SD card reader controller
- *  |  +- fast:2 I2S0  PCM I2S channel 0 controller
- *  |  +- fast:3 I2S1  PCM I2S channel 1 controller
- *  |  +- fast:4 I2C0  I2C channel 0 controller
- *  |  +- fast:5 I2C1  I2C channel 1 controller
- *  |  +- fast:6 SPI   SPI controller
- *  |  +- fast:7 UART1 Secondary UART (U335 only)
- *  |
- *  +- slow:0 SLOW bridge
- *     |
- *     +- slow:1 SYSCON (not possible to control)
- *     +- slow:2 WDOG Watchdog
- *     +- slow:3 UART0 primary UART
- *     +- slow:4 TIMER_APP Application timer - used in Linux
- *     +- slow:5 KEYPAD controller
- *     +- slow:6 GPIO controller
- *     +- slow:7 RTC controller
- *     +- slow:8 BT Bus Tracer (not used currently)
- *     +- slow:9 EH Event Handler (not used currently)
- *     +- slow:a TIMER_ACC Access style timer (not used currently)
- *     +- slow:b PPM (U335 only, what is that?)
- */
-
-/* Global syscon virtual base */
-static void __iomem *syscon_vbase;
-
-/**
- * struct clk_syscon - U300 syscon clock
- * @hw: corresponding clock hardware entry
- * @hw_ctrld: whether this clock is hardware controlled (for refcount etc)
- *	and does not need any magic pokes to be enabled/disabled
- * @reset: state holder, whether this block's reset line is asserted or not
- * @res_reg: reset line enable/disable flag register
- * @res_bit: bit for resetting or taking this consumer out of reset
- * @en_reg: clock line enable/disable flag register
- * @en_bit: bit for enabling/disabling this consumer clock line
- * @clk_val: magic value to poke in the register to enable/disable
- *	this one clock
- */
-struct clk_syscon {
-	struct clk_hw hw;
-	bool hw_ctrld;
-	bool reset;
-	void __iomem *res_reg;
-	u8 res_bit;
-	void __iomem *en_reg;
-	u8 en_bit;
-	u16 clk_val;
-};
-
-#define to_syscon(_hw) container_of(_hw, struct clk_syscon, hw)
-
-static DEFINE_SPINLOCK(syscon_resetreg_lock);
-
-/*
- * Reset control functions. We remember if a block has been
- * taken out of reset and don't remove the reset assertion again
- * and vice versa. Currently we only remove resets so the
- * enablement function is defined out.
- */
-static void syscon_block_reset_enable(struct clk_syscon *sclk)
-{
-	unsigned long iflags;
-	u16 val;
-
-	/* Not all blocks support resetting */
-	if (!sclk->res_reg)
-		return;
-	spin_lock_irqsave(&syscon_resetreg_lock, iflags);
-	val = readw(sclk->res_reg);
-	val |= BIT(sclk->res_bit);
-	writew(val, sclk->res_reg);
-	spin_unlock_irqrestore(&syscon_resetreg_lock, iflags);
-	sclk->reset = true;
-}
-
-static void syscon_block_reset_disable(struct clk_syscon *sclk)
-{
-	unsigned long iflags;
-	u16 val;
-
-	/* Not all blocks support resetting */
-	if (!sclk->res_reg)
-		return;
-	spin_lock_irqsave(&syscon_resetreg_lock, iflags);
-	val = readw(sclk->res_reg);
-	val &= ~BIT(sclk->res_bit);
-	writew(val, sclk->res_reg);
-	spin_unlock_irqrestore(&syscon_resetreg_lock, iflags);
-	sclk->reset = false;
-}
-
-static int syscon_clk_prepare(struct clk_hw *hw)
-{
-	struct clk_syscon *sclk = to_syscon(hw);
-
-	/* If the block is in reset, bring it out */
-	if (sclk->reset)
-		syscon_block_reset_disable(sclk);
-	return 0;
-}
-
-static void syscon_clk_unprepare(struct clk_hw *hw)
-{
-	struct clk_syscon *sclk = to_syscon(hw);
-
-	/* Please don't force the console into reset */
-	if (sclk->clk_val == U300_SYSCON_SBCER_UART_CLK_EN)
-		return;
-	/* When unpreparing, force block into reset */
-	if (!sclk->reset)
-		syscon_block_reset_enable(sclk);
-}
-
-static int syscon_clk_enable(struct clk_hw *hw)
-{
-	struct clk_syscon *sclk = to_syscon(hw);
-
-	/* Don't touch the hardware controlled clocks */
-	if (sclk->hw_ctrld)
-		return 0;
-	/* These cannot be controlled */
-	if (sclk->clk_val == 0xFFFFU)
-		return 0;
-
-	writew(sclk->clk_val, syscon_vbase + U300_SYSCON_SBCER);
-	return 0;
-}
-
-static void syscon_clk_disable(struct clk_hw *hw)
-{
-	struct clk_syscon *sclk = to_syscon(hw);
-
-	/* Don't touch the hardware controlled clocks */
-	if (sclk->hw_ctrld)
-		return;
-	if (sclk->clk_val == 0xFFFFU)
-		return;
-	/* Please don't disable the console port */
-	if (sclk->clk_val == U300_SYSCON_SBCER_UART_CLK_EN)
-		return;
-
-	writew(sclk->clk_val, syscon_vbase + U300_SYSCON_SBCDR);
-}
-
-static int syscon_clk_is_enabled(struct clk_hw *hw)
-{
-	struct clk_syscon *sclk = to_syscon(hw);
-	u16 val;
-
-	/* If no enable register defined, it's always-on */
-	if (!sclk->en_reg)
-		return 1;
-
-	val = readw(sclk->en_reg);
-	val &= BIT(sclk->en_bit);
-
-	return val ? 1 : 0;
-}
-
-static u16 syscon_get_perf(void)
-{
-	u16 val;
-
-	val = readw(syscon_vbase + U300_SYSCON_CCR);
-	val &= U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK;
-	return val;
-}
-
-static unsigned long
-syscon_clk_recalc_rate(struct clk_hw *hw,
-		       unsigned long parent_rate)
-{
-	struct clk_syscon *sclk = to_syscon(hw);
-	u16 perf = syscon_get_perf();
-
-	switch (sclk->clk_val) {
-	case U300_SYSCON_SBCER_FAST_BRIDGE_CLK_EN:
-	case U300_SYSCON_SBCER_I2C0_CLK_EN:
-	case U300_SYSCON_SBCER_I2C1_CLK_EN:
-	case U300_SYSCON_SBCER_MMC_CLK_EN:
-	case U300_SYSCON_SBCER_SPI_CLK_EN:
-		/* The FAST clocks have one progression */
-		switch (perf) {
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
-			return 13000000;
-		default:
-			return parent_rate; /* 26 MHz */
-		}
-	case U300_SYSCON_SBCER_DMAC_CLK_EN:
-	case U300_SYSCON_SBCER_NANDIF_CLK_EN:
-	case U300_SYSCON_SBCER_XGAM_CLK_EN:
-		/* AMBA interconnect peripherals */
-		switch (perf) {
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
-			return 6500000;
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
-			return 26000000;
-		default:
-			return parent_rate; /* 52 MHz */
-		}
-	case U300_SYSCON_SBCER_SEMI_CLK_EN:
-	case U300_SYSCON_SBCER_EMIF_CLK_EN:
-		/* EMIF speeds */
-		switch (perf) {
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
-			return 13000000;
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
-			return 52000000;
-		default:
-			return 104000000;
-		}
-	case U300_SYSCON_SBCER_CPU_CLK_EN:
-		/* And the fast CPU clock */
-		switch (perf) {
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
-			return 13000000;
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
-			return 52000000;
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH:
-			return 104000000;
-		default:
-			return parent_rate; /* 208 MHz */
-		}
-	default:
-		/*
-		 * The SLOW clocks and default just inherit the rate of
-		 * their parent (typically PLL13 13 MHz).
-		 */
-		return parent_rate;
-	}
-}
-
-static long
-syscon_clk_round_rate(struct clk_hw *hw, unsigned long rate,
-		      unsigned long *prate)
-{
-	struct clk_syscon *sclk = to_syscon(hw);
-
-	if (sclk->clk_val != U300_SYSCON_SBCER_CPU_CLK_EN)
-		return *prate;
-	/* We really only support setting the rate of the CPU clock */
-	if (rate <= 13000000)
-		return 13000000;
-	if (rate <= 52000000)
-		return 52000000;
-	if (rate <= 104000000)
-		return 104000000;
-	return 208000000;
-}
-
-static int syscon_clk_set_rate(struct clk_hw *hw, unsigned long rate,
-			       unsigned long parent_rate)
-{
-	struct clk_syscon *sclk = to_syscon(hw);
-	u16 val;
-
-	/* We only support setting the rate of the CPU clock */
-	if (sclk->clk_val != U300_SYSCON_SBCER_CPU_CLK_EN)
-		return -EINVAL;
-	switch (rate) {
-	case 13000000:
-		val = U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER;
-		break;
-	case 52000000:
-		val = U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE;
-		break;
-	case 104000000:
-		val = U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH;
-		break;
-	case 208000000:
-		val = U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST;
-		break;
-	default:
-		return -EINVAL;
-	}
-	val |= readw(syscon_vbase + U300_SYSCON_CCR) &
-		~U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK ;
-	writew(val, syscon_vbase + U300_SYSCON_CCR);
-	return 0;
-}
-
-static const struct clk_ops syscon_clk_ops = {
-	.prepare = syscon_clk_prepare,
-	.unprepare = syscon_clk_unprepare,
-	.enable = syscon_clk_enable,
-	.disable = syscon_clk_disable,
-	.is_enabled = syscon_clk_is_enabled,
-	.recalc_rate = syscon_clk_recalc_rate,
-	.round_rate = syscon_clk_round_rate,
-	.set_rate = syscon_clk_set_rate,
-};
-
-static struct clk_hw * __init
-syscon_clk_register(struct device *dev, const char *name,
-		    const char *parent_name, unsigned long flags,
-		    bool hw_ctrld,
-		    void __iomem *res_reg, u8 res_bit,
-		    void __iomem *en_reg, u8 en_bit,
-		    u16 clk_val)
-{
-	struct clk_hw *hw;
-	struct clk_syscon *sclk;
-	struct clk_init_data init;
-	int ret;
-
-	sclk = kzalloc(sizeof(*sclk), GFP_KERNEL);
-	if (!sclk)
-		return ERR_PTR(-ENOMEM);
-
-	init.name = name;
-	init.ops = &syscon_clk_ops;
-	init.flags = flags;
-	init.parent_names = (parent_name ? &parent_name : NULL);
-	init.num_parents = (parent_name ? 1 : 0);
-	sclk->hw.init = &init;
-	sclk->hw_ctrld = hw_ctrld;
-	/* Assume the block is in reset at registration */
-	sclk->reset = true;
-	sclk->res_reg = res_reg;
-	sclk->res_bit = res_bit;
-	sclk->en_reg = en_reg;
-	sclk->en_bit = en_bit;
-	sclk->clk_val = clk_val;
-
-	hw = &sclk->hw;
-	ret = clk_hw_register(dev, hw);
-	if (ret) {
-		kfree(sclk);
-		hw = ERR_PTR(ret);
-	}
-
-	return hw;
-}
-
-#define U300_CLK_TYPE_SLOW 0
-#define U300_CLK_TYPE_FAST 1
-#define U300_CLK_TYPE_REST 2
-
-/**
- * struct u300_clock - defines the bits and pieces for a certain clock
- * @type: the clock type, slow fast or rest
- * @id: the bit in the slow/fast/rest register for this clock
- * @hw_ctrld: whether the clock is hardware controlled
- * @clk_val: a value to poke in the one-write enable/disable registers
- */
-struct u300_clock {
-	u8 type;
-	u8 id;
-	bool hw_ctrld;
-	u16 clk_val;
-};
-
-static struct u300_clock const u300_clk_lookup[] __initconst = {
-	{
-		.type = U300_CLK_TYPE_REST,
-		.id = 3,
-		.hw_ctrld = true,
-		.clk_val = U300_SYSCON_SBCER_CPU_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_REST,
-		.id = 4,
-		.hw_ctrld = true,
-		.clk_val = U300_SYSCON_SBCER_DMAC_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_REST,
-		.id = 5,
-		.hw_ctrld = false,
-		.clk_val = U300_SYSCON_SBCER_EMIF_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_REST,
-		.id = 6,
-		.hw_ctrld = false,
-		.clk_val = U300_SYSCON_SBCER_NANDIF_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_REST,
-		.id = 8,
-		.hw_ctrld = true,
-		.clk_val = U300_SYSCON_SBCER_XGAM_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_REST,
-		.id = 9,
-		.hw_ctrld = false,
-		.clk_val = U300_SYSCON_SBCER_SEMI_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_REST,
-		.id = 10,
-		.hw_ctrld = true,
-		.clk_val = U300_SYSCON_SBCER_AHB_SUBSYS_BRIDGE_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_REST,
-		.id = 12,
-		.hw_ctrld = false,
-		/* INTCON: cannot be enabled, just taken out of reset */
-		.clk_val = 0xFFFFU,
-	},
-	{
-		.type = U300_CLK_TYPE_FAST,
-		.id = 0,
-		.hw_ctrld = true,
-		.clk_val = U300_SYSCON_SBCER_FAST_BRIDGE_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_FAST,
-		.id = 1,
-		.hw_ctrld = false,
-		.clk_val = U300_SYSCON_SBCER_I2C0_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_FAST,
-		.id = 2,
-		.hw_ctrld = false,
-		.clk_val = U300_SYSCON_SBCER_I2C1_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_FAST,
-		.id = 5,
-		.hw_ctrld = false,
-		.clk_val = U300_SYSCON_SBCER_MMC_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_FAST,
-		.id = 6,
-		.hw_ctrld = false,
-		.clk_val = U300_SYSCON_SBCER_SPI_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_SLOW,
-		.id = 0,
-		.hw_ctrld = true,
-		.clk_val = U300_SYSCON_SBCER_SLOW_BRIDGE_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_SLOW,
-		.id = 1,
-		.hw_ctrld = false,
-		.clk_val = U300_SYSCON_SBCER_UART_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_SLOW,
-		.id = 4,
-		.hw_ctrld = false,
-		.clk_val = U300_SYSCON_SBCER_GPIO_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_SLOW,
-		.id = 6,
-		.hw_ctrld = true,
-		/* No clock enable register bit */
-		.clk_val = 0xFFFFU,
-	},
-	{
-		.type = U300_CLK_TYPE_SLOW,
-		.id = 7,
-		.hw_ctrld = false,
-		.clk_val = U300_SYSCON_SBCER_APP_TMR_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_SLOW,
-		.id = 8,
-		.hw_ctrld = false,
-		.clk_val = U300_SYSCON_SBCER_ACC_TMR_CLK_EN,
-	},
-};
-
-static void __init of_u300_syscon_clk_init(struct device_node *np)
-{
-	struct clk_hw *hw = ERR_PTR(-EINVAL);
-	const char *clk_name = np->name;
-	const char *parent_name;
-	void __iomem *res_reg;
-	void __iomem *en_reg;
-	u32 clk_type;
-	u32 clk_id;
-	int i;
-
-	if (of_property_read_u32(np, "clock-type", &clk_type)) {
-		pr_err("%s: syscon clock \"%s\" missing clock-type property\n",
-		       __func__, clk_name);
-		return;
-	}
-	if (of_property_read_u32(np, "clock-id", &clk_id)) {
-		pr_err("%s: syscon clock \"%s\" missing clock-id property\n",
-		       __func__, clk_name);
-		return;
-	}
-	parent_name = of_clk_get_parent_name(np, 0);
-
-	switch (clk_type) {
-	case U300_CLK_TYPE_SLOW:
-		res_reg = syscon_vbase + U300_SYSCON_RSR;
-		en_reg = syscon_vbase + U300_SYSCON_CESR;
-		break;
-	case U300_CLK_TYPE_FAST:
-		res_reg = syscon_vbase + U300_SYSCON_RFR;
-		en_reg = syscon_vbase + U300_SYSCON_CEFR;
-		break;
-	case U300_CLK_TYPE_REST:
-		res_reg = syscon_vbase + U300_SYSCON_RRR;
-		en_reg = syscon_vbase + U300_SYSCON_CERR;
-		break;
-	default:
-		pr_err("unknown clock type %x specified\n", clk_type);
-		return;
-	}
-
-	for (i = 0; i < ARRAY_SIZE(u300_clk_lookup); i++) {
-		const struct u300_clock *u3clk = &u300_clk_lookup[i];
-
-		if (u3clk->type == clk_type && u3clk->id == clk_id)
-			hw = syscon_clk_register(NULL, clk_name, parent_name,
-						 0, u3clk->hw_ctrld,
-						 res_reg, u3clk->id,
-						 en_reg, u3clk->id,
-						 u3clk->clk_val);
-	}
-
-	if (!IS_ERR(hw)) {
-		of_clk_add_hw_provider(np, of_clk_hw_simple_get, hw);
-
-		/*
-		 * Some few system clocks - device tree does not
-		 * represent clocks without a corresponding device node.
-		 * for now we add these three clocks here.
-		 */
-		if (clk_type == U300_CLK_TYPE_REST && clk_id == 5)
-			clk_hw_register_clkdev(hw, NULL, "pl172");
-		if (clk_type == U300_CLK_TYPE_REST && clk_id == 9)
-			clk_hw_register_clkdev(hw, NULL, "semi");
-		if (clk_type == U300_CLK_TYPE_REST && clk_id == 12)
-			clk_hw_register_clkdev(hw, NULL, "intcon");
-	}
-}
-
-/**
- * struct clk_mclk - U300 MCLK clock (MMC/SD clock)
- * @hw: corresponding clock hardware entry
- * @is_mspro: if this is the memory stick clock rather than MMC/SD
- */
-struct clk_mclk {
-	struct clk_hw hw;
-	bool is_mspro;
-};
-
-#define to_mclk(_hw) container_of(_hw, struct clk_mclk, hw)
-
-static int mclk_clk_prepare(struct clk_hw *hw)
-{
-	struct clk_mclk *mclk = to_mclk(hw);
-	u16 val;
-
-	/* The MMC and MSPRO clocks need some special set-up */
-	if (!mclk->is_mspro) {
-		/* Set default MMC clock divisor to 18.9 MHz */
-		writew(0x0054U, syscon_vbase + U300_SYSCON_MMF0R);
-		val = readw(syscon_vbase + U300_SYSCON_MMCR);
-		/* Disable the MMC feedback clock */
-		val &= ~U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE;
-		/* Disable MSPRO frequency */
-		val &= ~U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE;
-		writew(val, syscon_vbase + U300_SYSCON_MMCR);
-	} else {
-		val = readw(syscon_vbase + U300_SYSCON_MMCR);
-		/* Disable the MMC feedback clock */
-		val &= ~U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE;
-		/* Enable MSPRO frequency */
-		val |= U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE;
-		writew(val, syscon_vbase + U300_SYSCON_MMCR);
-	}
-
-	return 0;
-}
-
-static unsigned long
-mclk_clk_recalc_rate(struct clk_hw *hw,
-		     unsigned long parent_rate)
-{
-	u16 perf = syscon_get_perf();
-
-	switch (perf) {
-	case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
-		/*
-		 * Here, the 208 MHz PLL gets shut down and the always
-		 * on 13 MHz PLL used for RTC etc kicks into use
-		 * instead.
-		 */
-		return 13000000;
-	case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
-	case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
-	case U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH:
-	case U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST:
-	{
-		/*
-		 * This clock is under program control. The register is
-		 * divided in two nybbles, bit 7-4 gives cycles-1 to count
-		 * high, bit 3-0 gives cycles-1 to count low. Distribute
-		 * these with no more than 1 cycle difference between
-		 * low and high and add low and high to get the actual
-		 * divisor. The base PLL is 208 MHz. Writing 0x00 will
-		 * divide by 1 and 1 so the highest frequency possible
-		 * is 104 MHz.
-		 *
-		 * e.g. 0x54 =>
-		 * f = 208 / ((5+1) + (4+1)) = 208 / 11 = 18.9 MHz
-		 */
-		u16 val = readw(syscon_vbase + U300_SYSCON_MMF0R) &
-			U300_SYSCON_MMF0R_MASK;
-		switch (val) {
-		case 0x0054:
-			return 18900000;
-		case 0x0044:
-			return 20800000;
-		case 0x0043:
-			return 23100000;
-		case 0x0033:
-			return 26000000;
-		case 0x0032:
-			return 29700000;
-		case 0x0022:
-			return 34700000;
-		case 0x0021:
-			return 41600000;
-		case 0x0011:
-			return 52000000;
-		case 0x0000:
-			return 104000000;
-		default:
-			break;
-		}
-	}
-	default:
-		break;
-	}
-	return parent_rate;
-}
-
-static long
-mclk_clk_round_rate(struct clk_hw *hw, unsigned long rate,
-		    unsigned long *prate)
-{
-	if (rate <= 18900000)
-		return 18900000;
-	if (rate <= 20800000)
-		return 20800000;
-	if (rate <= 23100000)
-		return 23100000;
-	if (rate <= 26000000)
-		return 26000000;
-	if (rate <= 29700000)
-		return 29700000;
-	if (rate <= 34700000)
-		return 34700000;
-	if (rate <= 41600000)
-		return 41600000;
-	/* Highest rate */
-	return 52000000;
-}
-
-static int mclk_clk_set_rate(struct clk_hw *hw, unsigned long rate,
-			     unsigned long parent_rate)
-{
-	u16 val;
-	u16 reg;
-
-	switch (rate) {
-	case 18900000:
-		val = 0x0054;
-		break;
-	case 20800000:
-		val = 0x0044;
-		break;
-	case 23100000:
-		val = 0x0043;
-		break;
-	case 26000000:
-		val = 0x0033;
-		break;
-	case 29700000:
-		val = 0x0032;
-		break;
-	case 34700000:
-		val = 0x0022;
-		break;
-	case 41600000:
-		val = 0x0021;
-		break;
-	case 52000000:
-		val = 0x0011;
-		break;
-	case 104000000:
-		val = 0x0000;
-		break;
-	default:
-		return -EINVAL;
-	}
-
-	reg = readw(syscon_vbase + U300_SYSCON_MMF0R) &
-		~U300_SYSCON_MMF0R_MASK;
-	writew(reg | val, syscon_vbase + U300_SYSCON_MMF0R);
-	return 0;
-}
-
-static const struct clk_ops mclk_ops = {
-	.prepare = mclk_clk_prepare,
-	.recalc_rate = mclk_clk_recalc_rate,
-	.round_rate = mclk_clk_round_rate,
-	.set_rate = mclk_clk_set_rate,
-};
-
-static struct clk_hw * __init
-mclk_clk_register(struct device *dev, const char *name,
-		  const char *parent_name, bool is_mspro)
-{
-	struct clk_hw *hw;
-	struct clk_mclk *mclk;
-	struct clk_init_data init;
-	int ret;
-
-	mclk = kzalloc(sizeof(*mclk), GFP_KERNEL);
-	if (!mclk)
-		return ERR_PTR(-ENOMEM);
-
-	init.name = "mclk";
-	init.ops = &mclk_ops;
-	init.flags = 0;
-	init.parent_names = (parent_name ? &parent_name : NULL);
-	init.num_parents = (parent_name ? 1 : 0);
-	mclk->hw.init = &init;
-	mclk->is_mspro = is_mspro;
-
-	hw = &mclk->hw;
-	ret = clk_hw_register(dev, hw);
-	if (ret) {
-		kfree(mclk);
-		hw = ERR_PTR(ret);
-	}
-
-	return hw;
-}
-
-static void __init of_u300_syscon_mclk_init(struct device_node *np)
-{
-	struct clk_hw *hw;
-	const char *clk_name = np->name;
-	const char *parent_name;
-
-	parent_name = of_clk_get_parent_name(np, 0);
-	hw = mclk_clk_register(NULL, clk_name, parent_name, false);
-	if (!IS_ERR(hw))
-		of_clk_add_hw_provider(np, of_clk_hw_simple_get, hw);
-}
-
-static const struct of_device_id u300_clk_match[] __initconst = {
-	{
-		.compatible = "fixed-clock",
-		.data = of_fixed_clk_setup,
-	},
-	{
-		.compatible = "fixed-factor-clock",
-		.data = of_fixed_factor_clk_setup,
-	},
-	{
-		.compatible = "stericsson,u300-syscon-clk",
-		.data = of_u300_syscon_clk_init,
-	},
-	{
-		.compatible = "stericsson,u300-syscon-mclk",
-		.data = of_u300_syscon_mclk_init,
-	},
-	{}
-};
-
-
-void __init u300_clk_init(void __iomem *base)
-{
-	u16 val;
-
-	syscon_vbase = base;
-
-	/* Set system to run at PLL208, max performance, a known state. */
-	val = readw(syscon_vbase + U300_SYSCON_CCR);
-	val &= ~U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK;
-	writew(val, syscon_vbase + U300_SYSCON_CCR);
-	/* Wait for the PLL208 to lock if not locked in yet */
-	while (!(readw(syscon_vbase + U300_SYSCON_CSR) &
-		 U300_SYSCON_CSR_PLL208_LOCK_IND));
-
-	/* Power management enable */
-	val = readw(syscon_vbase + U300_SYSCON_PMCR);
-	val |= U300_SYSCON_PMCR_PWR_MGNT_ENABLE;
-	writew(val, syscon_vbase + U300_SYSCON_PMCR);
-
-	of_clk_init(u300_clk_match);
-}