ide: remove useless subdirs from drivers/ide/

Suggested-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

1 files changed, 0 insertions, 429 deletions

diff --git a/drivers/ide/legacy/qd65xx.c b/drivers/ide/legacy/qd65xx.c
deleted file mode 100644
index bc27c7aba936..000000000000
--- a/drivers/ide/legacy/qd65xx.c
+++ /dev/null
@@ -1,429 +0,0 @@
-/*
- *  Copyright (C) 1996-2001  Linus Torvalds & author (see below)
- */
-
-/*
- *  Version 0.03	Cleaned auto-tune, added probe
- *  Version 0.04	Added second channel tuning
- *  Version 0.05	Enhanced tuning ; added qd6500 support
- *  Version 0.06	Added dos driver's list
- *  Version 0.07	Second channel bug fix 
- *
- * QDI QD6500/QD6580 EIDE controller fast support
- *
- * To activate controller support, use "ide0=qd65xx"
- */
-
-/*
- * Rewritten from the work of Colten Edwards <pje120@cs.usask.ca> by
- * Samuel Thibault <samuel.thibault@fnac.net>
- */
-
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/timer.h>
-#include <linux/mm.h>
-#include <linux/ioport.h>
-#include <linux/blkdev.h>
-#include <linux/ide.h>
-#include <linux/init.h>
-#include <asm/system.h>
-#include <asm/io.h>
-
-#define DRV_NAME "qd65xx"
-
-#include "qd65xx.h"
-
-/*
- * I/O ports are 0x30-0x31 (and 0x32-0x33 for qd6580)
- *            or 0xb0-0xb1 (and 0xb2-0xb3 for qd6580)
- *	-- qd6500 is a single IDE interface
- *	-- qd6580 is a dual IDE interface
- *
- * More research on qd6580 being done by willmore@cig.mot.com (David)
- * More Information given by Petr Soucek (petr@ryston.cz)
- * http://www.ryston.cz/petr/vlb
- */
-
-/*
- * base: Timer1
- *
- *
- * base+0x01: Config (R/O)
- *
- * bit 0: ide baseport: 1 = 0x1f0 ; 0 = 0x170 (only useful for qd6500)
- * bit 1: qd65xx baseport: 1 = 0xb0 ; 0 = 0x30
- * bit 2: ID3: bus speed: 1 = <=33MHz ; 0 = >33MHz
- * bit 3: qd6500: 1 = disabled, 0 = enabled
- *        qd6580: 1
- * upper nibble:
- *        qd6500: 1100
- *        qd6580: either 1010 or 0101
- *
- *
- * base+0x02: Timer2 (qd6580 only)
- *
- *
- * base+0x03: Control (qd6580 only)
- *
- * bits 0-3 must always be set 1
- * bit 4 must be set 1, but is set 0 by dos driver while measuring vlb clock
- * bit 0 : 1 = Only primary port enabled : channel 0 for hda, channel 1 for hdb
- *         0 = Primary and Secondary ports enabled : channel 0 for hda & hdb
- *                                                   channel 1 for hdc & hdd
- * bit 1 : 1 = only disks on primary port
- *         0 = disks & ATAPI devices on primary port
- * bit 2-4 : always 0
- * bit 5 : status, but of what ?
- * bit 6 : always set 1 by dos driver
- * bit 7 : set 1 for non-ATAPI devices on primary port
- *	(maybe read-ahead and post-write buffer ?)
- */
-
-static int timings[4]={-1,-1,-1,-1}; /* stores current timing for each timer */
-
-/*
- * qd65xx_select:
- *
- * This routine is invoked to prepare for access to a given drive.
- */
-
-static void qd65xx_select(ide_drive_t *drive)
-{
-	u8 index = ((	(QD_TIMREG(drive)) & 0x80 ) >> 7) |
-			(QD_TIMREG(drive) & 0x02);
-
-	if (timings[index] != QD_TIMING(drive))
-		outb(timings[index] = QD_TIMING(drive), QD_TIMREG(drive));
-}
-
-/*
- * qd6500_compute_timing
- *
- * computes the timing value where
- *	lower nibble represents active time,   in count of VLB clocks
- *	upper nibble represents recovery time, in count of VLB clocks
- */
-
-static u8 qd6500_compute_timing (ide_hwif_t *hwif, int active_time, int recovery_time)
-{
-	int clk = ide_vlb_clk ? ide_vlb_clk : 50;
-	u8 act_cyc, rec_cyc;
-
-	if (clk <= 33) {
-		act_cyc =  9 - IDE_IN(active_time   * clk / 1000 + 1, 2,  9);
-		rec_cyc = 15 - IDE_IN(recovery_time * clk / 1000 + 1, 0, 15);
-	} else {
-		act_cyc =  8 - IDE_IN(active_time   * clk / 1000 + 1, 1,  8);
-		rec_cyc = 18 - IDE_IN(recovery_time * clk / 1000 + 1, 3, 18);
-	}
-
-	return (rec_cyc << 4) | 0x08 | act_cyc;
-}
-
-/*
- * qd6580_compute_timing
- *
- * idem for qd6580
- */
-
-static u8 qd6580_compute_timing (int active_time, int recovery_time)
-{
-	int clk = ide_vlb_clk ? ide_vlb_clk : 50;
-	u8 act_cyc, rec_cyc;
-
-	act_cyc = 17 - IDE_IN(active_time   * clk / 1000 + 1, 2, 17);
-	rec_cyc = 15 - IDE_IN(recovery_time * clk / 1000 + 1, 2, 15);
-
-	return (rec_cyc << 4) | act_cyc;
-}
-
-/*
- * qd_find_disk_type
- *
- * tries to find timing from dos driver's table
- */
-
-static int qd_find_disk_type (ide_drive_t *drive,
-		int *active_time, int *recovery_time)
-{
-	struct qd65xx_timing_s *p;
-	char *m = (char *)&drive->id[ATA_ID_PROD];
-	char model[ATA_ID_PROD_LEN];
-
-	if (*m == 0)
-		return 0;
-
-	strncpy(model, m, ATA_ID_PROD_LEN);
-	ide_fixstring(model, ATA_ID_PROD_LEN, 1); /* byte-swap */
-
-	for (p = qd65xx_timing ; p->offset != -1 ; p++) {
-		if (!strncmp(p->model, model+p->offset, 4)) {
-			printk(KERN_DEBUG "%s: listed !\n", drive->name);
-			*active_time = p->active;
-			*recovery_time = p->recovery;
-			return 1;
-		}
-	}
-	return 0;
-}
-
-/*
- * qd_set_timing:
- *
- * records the timing
- */
-
-static void qd_set_timing (ide_drive_t *drive, u8 timing)
-{
-	drive->drive_data &= 0xff00;
-	drive->drive_data |= timing;
-
-	printk(KERN_DEBUG "%s: %#x\n", drive->name, timing);
-}
-
-static void qd6500_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
-	u16 *id = drive->id;
-	int active_time   = 175;
-	int recovery_time = 415; /* worst case values from the dos driver */
-
-	/*
-	 * FIXME: use "pio" value
-	 */
-	if (!qd_find_disk_type(drive, &active_time, &recovery_time) &&
-	    (id[ATA_ID_OLD_PIO_MODES] & 0xff) && (id[ATA_ID_FIELD_VALID] & 2) &&
-	    id[ATA_ID_EIDE_PIO] >= 240) {
-		printk(KERN_INFO "%s: PIO mode%d\n", drive->name,
-			id[ATA_ID_OLD_PIO_MODES] & 0xff);
-		active_time = 110;
-		recovery_time = drive->id[ATA_ID_EIDE_PIO] - 120;
-	}
-
-	qd_set_timing(drive, qd6500_compute_timing(HWIF(drive), active_time, recovery_time));
-}
-
-static void qd6580_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
-	ide_hwif_t *hwif = drive->hwif;
-	struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio);
-	unsigned int cycle_time;
-	int active_time   = 175;
-	int recovery_time = 415; /* worst case values from the dos driver */
-	u8 base = (hwif->config_data & 0xff00) >> 8;
-
-	if (drive->id && !qd_find_disk_type(drive, &active_time, &recovery_time)) {
-		cycle_time = ide_pio_cycle_time(drive, pio);
-
-		switch (pio) {
-			case 0: break;
-			case 3:
-				if (cycle_time >= 110) {
-					active_time = 86;
-					recovery_time = cycle_time - 102;
-				} else
-					printk(KERN_WARNING "%s: Strange recovery time !\n",drive->name);
-				break;
-			case 4:
-				if (cycle_time >= 69) {
-					active_time = 70;
-					recovery_time = cycle_time - 61;
-				} else
-					printk(KERN_WARNING "%s: Strange recovery time !\n",drive->name);
-				break;
-			default:
-				if (cycle_time >= 180) {
-					active_time = 110;
-					recovery_time = cycle_time - 120;
-				} else {
-					active_time = t->active;
-					recovery_time = cycle_time - active_time;
-				}
-		}
-		printk(KERN_INFO "%s: PIO mode%d\n", drive->name,pio);
-	}
-
-	if (!HWIF(drive)->channel && drive->media != ide_disk) {
-		outb(0x5f, QD_CONTROL_PORT);
-		printk(KERN_WARNING "%s: ATAPI: disabled read-ahead FIFO "
-			"and post-write buffer on %s.\n",
-			drive->name, HWIF(drive)->name);
-	}
-
-	qd_set_timing(drive, qd6580_compute_timing(active_time, recovery_time));
-}
-
-/*
- * qd_testreg
- *
- * tests if the given port is a register
- */
-
-static int __init qd_testreg(int port)
-{
-	unsigned long flags;
-	u8 savereg, readreg;
-
-	local_irq_save(flags);
-	savereg = inb_p(port);
-	outb_p(QD_TESTVAL, port);	/* safe value */
-	readreg = inb_p(port);
-	outb(savereg, port);
-	local_irq_restore(flags);
-
-	if (savereg == QD_TESTVAL) {
-		printk(KERN_ERR "Outch ! the probe for qd65xx isn't reliable !\n");
-		printk(KERN_ERR "Please contact maintainers to tell about your hardware\n");
-		printk(KERN_ERR "Assuming qd65xx is not present.\n");
-		return 1;
-	}
-
-	return (readreg != QD_TESTVAL);
-}
-
-static void __init qd6500_init_dev(ide_drive_t *drive)
-{
-	ide_hwif_t *hwif = drive->hwif;
-	u8 base = (hwif->config_data & 0xff00) >> 8;
-	u8 config = QD_CONFIG(hwif);
-
-	drive->drive_data = QD6500_DEF_DATA;
-}
-
-static void __init qd6580_init_dev(ide_drive_t *drive)
-{
-	ide_hwif_t *hwif = drive->hwif;
-	u16 t1, t2;
-	u8 base = (hwif->config_data & 0xff00) >> 8;
-	u8 config = QD_CONFIG(hwif);
-
-	if (hwif->host_flags & IDE_HFLAG_SINGLE) {
-		t1 = QD6580_DEF_DATA;
-		t2 = QD6580_DEF_DATA2;
-	} else
-		t2 = t1 = hwif->channel ? QD6580_DEF_DATA2 : QD6580_DEF_DATA;
-
-	drive->drive_data = (drive->dn & 1) ? t2 : t1;
-}
-
-static const struct ide_port_ops qd6500_port_ops = {
-	.init_dev		= qd6500_init_dev,
-	.set_pio_mode		= qd6500_set_pio_mode,
-	.selectproc		= qd65xx_select,
-};
-
-static const struct ide_port_ops qd6580_port_ops = {
-	.init_dev		= qd6580_init_dev,
-	.set_pio_mode		= qd6580_set_pio_mode,
-	.selectproc		= qd65xx_select,
-};
-
-static const struct ide_port_info qd65xx_port_info __initdata = {
-	.name			= DRV_NAME,
-	.chipset		= ide_qd65xx,
-	.host_flags		= IDE_HFLAG_IO_32BIT |
-				  IDE_HFLAG_NO_DMA,
-	.pio_mask		= ATA_PIO4,
-};
-
-/*
- * qd_probe:
- *
- * looks at the specified baseport, and if qd found, registers & initialises it
- * return 1 if another qd may be probed
- */
-
-static int __init qd_probe(int base)
-{
-	int rc;
-	u8 config, unit, control;
-	struct ide_port_info d = qd65xx_port_info;
-
-	config = inb(QD_CONFIG_PORT);
-
-	if (! ((config & QD_CONFIG_BASEPORT) >> 1 == (base == 0xb0)) )
-		return -ENODEV;
-
-	unit = ! (config & QD_CONFIG_IDE_BASEPORT);
-
-	if (unit)
-		d.host_flags |= IDE_HFLAG_QD_2ND_PORT;
-
-	switch (config & 0xf0) {
-	case QD_CONFIG_QD6500:
-		if (qd_testreg(base))
-			 return -ENODEV;	/* bad register */
-
-		if (config & QD_CONFIG_DISABLED) {
-			printk(KERN_WARNING "qd6500 is disabled !\n");
-			return -ENODEV;
-		}
-
-		printk(KERN_NOTICE "qd6500 at %#x\n", base);
-		printk(KERN_DEBUG "qd6500: config=%#x, ID3=%u\n",
-			config, QD_ID3);
-
-		d.port_ops = &qd6500_port_ops;
-		d.host_flags |= IDE_HFLAG_SINGLE;
-		break;
-	case QD_CONFIG_QD6580_A:
-	case QD_CONFIG_QD6580_B:
-		if (qd_testreg(base) || qd_testreg(base + 0x02))
-			return -ENODEV;	/* bad registers */
-
-		control = inb(QD_CONTROL_PORT);
-
-		printk(KERN_NOTICE "qd6580 at %#x\n", base);
-		printk(KERN_DEBUG "qd6580: config=%#x, control=%#x, ID3=%u\n",
-			config, control, QD_ID3);
-
-		outb(QD_DEF_CONTR, QD_CONTROL_PORT);
-
-		d.port_ops = &qd6580_port_ops;
-		if (control & QD_CONTR_SEC_DISABLED)
-			d.host_flags |= IDE_HFLAG_SINGLE;
-
-		printk(KERN_INFO "qd6580: %s IDE board\n",
-			(control & QD_CONTR_SEC_DISABLED) ? "single" : "dual");
-		break;
-	default:
-		return -ENODEV;
-	}
-
-	rc = ide_legacy_device_add(&d, (base << 8) | config);
-
-	if (d.host_flags & IDE_HFLAG_SINGLE)
-		return (rc == 0) ? 1 : rc;
-
-	return rc;
-}
-
-static int probe_qd65xx;
-
-module_param_named(probe, probe_qd65xx, bool, 0);
-MODULE_PARM_DESC(probe, "probe for QD65xx chipsets");
-
-static int __init qd65xx_init(void)
-{
-	int rc1, rc2 = -ENODEV;
-
-	if (probe_qd65xx == 0)
-		return -ENODEV;
-
-	rc1 = qd_probe(0x30);
-	if (rc1)
-		rc2 = qd_probe(0xb0);
-
-	if (rc1 < 0 && rc2 < 0)
-		return -ENODEV;
-
-	return 0;
-}
-
-module_init(qd65xx_init);
-
-MODULE_AUTHOR("Samuel Thibault");
-MODULE_DESCRIPTION("support of qd65xx vlb ide chipset");
-MODULE_LICENSE("GPL");