ide: remove the legacy ide driver

The legay ide driver has been replace with libata starting in 2003 and has
been scheduled for removal for a while.  Finally kill it off so that we
can start cleaning up various bits of cruft it forced on the block layer.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

1 files changed, 0 insertions, 367 deletions

diff --git a/drivers/ide/sl82c105.c b/drivers/ide/sl82c105.c
deleted file mode 100644
index 5c24c420c438..000000000000
--- a/drivers/ide/sl82c105.c
+++ /dev/null
@@ -1,367 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * SL82C105/Winbond 553 IDE driver
- *
- * Maintainer unknown.
- *
- * Drive tuning added from Rebel.com's kernel sources
- *  -- Russell King (15/11/98) linux@arm.linux.org.uk
- * 
- * Merge in Russell's HW workarounds, fix various problems
- * with the timing registers setup.
- *  -- Benjamin Herrenschmidt (01/11/03) benh@kernel.crashing.org
- *
- * Copyright (C) 2006-2007,2009 MontaVista Software, Inc. <source@mvista.com>
- * Copyright (C)      2007 Bartlomiej Zolnierkiewicz
- */
-
-#include <linux/types.h>
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/ide.h>
-
-#include <asm/io.h>
-
-#define DRV_NAME "sl82c105"
-
-/*
- * SL82C105 PCI config register 0x40 bits.
- */
-#define CTRL_IDE_IRQB   (1 << 30)
-#define CTRL_IDE_IRQA   (1 << 28)
-#define CTRL_LEGIRQ     (1 << 11)
-#define CTRL_P1F16      (1 << 5)
-#define CTRL_P1EN       (1 << 4)
-#define CTRL_P0F16      (1 << 1)
-#define CTRL_P0EN       (1 << 0)
-
-/*
- * Convert a PIO mode and cycle time to the required on/off times
- * for the interface.  This has protection against runaway timings.
- */
-static unsigned int get_pio_timings(ide_drive_t *drive, u8 pio)
-{
-	struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio);
-	unsigned int cmd_on, cmd_off;
-	u8 iordy = 0;
-
-	cmd_on  = (t->active + 29) / 30;
-	cmd_off = (ide_pio_cycle_time(drive, pio) - 30 * cmd_on + 29) / 30;
-
-	if (cmd_on == 0)
-		cmd_on = 1;
-
-	if (cmd_off == 0)
-		cmd_off = 1;
-
-	if (ide_pio_need_iordy(drive, pio))
-		iordy = 0x40;
-
-	return (cmd_on - 1) << 8 | (cmd_off - 1) | iordy;
-}
-
-/*
- * Configure the chipset for PIO mode.
- */
-static void sl82c105_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
-	struct pci_dev *dev	= to_pci_dev(hwif->dev);
-	unsigned long timings	= (unsigned long)ide_get_drivedata(drive);
-	int reg			= 0x44 + drive->dn * 4;
-	u16 drv_ctrl;
-	const u8 pio		= drive->pio_mode - XFER_PIO_0;
-
-	drv_ctrl = get_pio_timings(drive, pio);
-
-	/*
-	 * Store the PIO timings so that we can restore them
-	 * in case DMA will be turned off...
-	 */
-	timings &= 0xffff0000;
-	timings |= drv_ctrl;
-	ide_set_drivedata(drive, (void *)timings);
-
-	pci_write_config_word(dev, reg,  drv_ctrl);
-	pci_read_config_word (dev, reg, &drv_ctrl);
-
-	printk(KERN_DEBUG "%s: selected %s (%dns) (%04X)\n", drive->name,
-			  ide_xfer_verbose(pio + XFER_PIO_0),
-			  ide_pio_cycle_time(drive, pio), drv_ctrl);
-}
-
-/*
- * Configure the chipset for DMA mode.
- */
-static void sl82c105_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
-	static u16 mwdma_timings[] = {0x0707, 0x0201, 0x0200};
-	unsigned long timings = (unsigned long)ide_get_drivedata(drive);
-	u16 drv_ctrl;
-	const u8 speed = drive->dma_mode;
-
-	drv_ctrl = mwdma_timings[speed - XFER_MW_DMA_0];
-
-	/*
-	 * Store the DMA timings so that we can actually program
-	 * them when DMA will be turned on...
-	 */
-	timings &= 0x0000ffff;
-	timings |= (unsigned long)drv_ctrl << 16;
-	ide_set_drivedata(drive, (void *)timings);
-}
-
-static int sl82c105_test_irq(ide_hwif_t *hwif)
-{
-	struct pci_dev *dev	= to_pci_dev(hwif->dev);
-	u32 val, mask		= hwif->channel ? CTRL_IDE_IRQB : CTRL_IDE_IRQA;
-
-	pci_read_config_dword(dev, 0x40, &val);
-
-	return (val & mask) ? 1 : 0;
-}
-
-/*
- * The SL82C105 holds off all IDE interrupts while in DMA mode until
- * all DMA activity is completed.  Sometimes this causes problems (eg,
- * when the drive wants to report an error condition).
- *
- * 0x7e is a "chip testing" register.  Bit 2 resets the DMA controller
- * state machine.  We need to kick this to work around various bugs.
- */
-static inline void sl82c105_reset_host(struct pci_dev *dev)
-{
-	u16 val;
-
-	pci_read_config_word(dev, 0x7e, &val);
-	pci_write_config_word(dev, 0x7e, val | (1 << 2));
-	pci_write_config_word(dev, 0x7e, val & ~(1 << 2));
-}
-
-/*
- * If we get an IRQ timeout, it might be that the DMA state machine
- * got confused.  Fix from Todd Inglett.  Details from Winbond.
- *
- * This function is called when the IDE timer expires, the drive
- * indicates that it is READY, and we were waiting for DMA to complete.
- */
-static void sl82c105_dma_lost_irq(ide_drive_t *drive)
-{
-	ide_hwif_t *hwif	= drive->hwif;
-	struct pci_dev *dev	= to_pci_dev(hwif->dev);
-	u32 val, mask		= hwif->channel ? CTRL_IDE_IRQB : CTRL_IDE_IRQA;
-	u8 dma_cmd;
-
-	printk(KERN_WARNING "sl82c105: lost IRQ, resetting host\n");
-
-	/*
-	 * Check the raw interrupt from the drive.
-	 */
-	pci_read_config_dword(dev, 0x40, &val);
-	if (val & mask)
-		printk(KERN_INFO "sl82c105: drive was requesting IRQ, "
-		       "but host lost it\n");
-
-	/*
-	 * Was DMA enabled?  If so, disable it - we're resetting the
-	 * host.  The IDE layer will be handling the drive for us.
-	 */
-	dma_cmd = inb(hwif->dma_base + ATA_DMA_CMD);
-	if (dma_cmd & 1) {
-		outb(dma_cmd & ~1, hwif->dma_base + ATA_DMA_CMD);
-		printk(KERN_INFO "sl82c105: DMA was enabled\n");
-	}
-
-	sl82c105_reset_host(dev);
-}
-
-/*
- * ATAPI devices can cause the SL82C105 DMA state machine to go gaga.
- * Winbond recommend that the DMA state machine is reset prior to
- * setting the bus master DMA enable bit.
- *
- * The generic IDE core will have disabled the BMEN bit before this
- * function is called.
- */
-static void sl82c105_dma_start(ide_drive_t *drive)
-{
-	ide_hwif_t *hwif	= drive->hwif;
-	struct pci_dev *dev	= to_pci_dev(hwif->dev);
-	int reg 		= 0x44 + drive->dn * 4;
-
-	pci_write_config_word(dev, reg,
-			      (unsigned long)ide_get_drivedata(drive) >> 16);
-
-	sl82c105_reset_host(dev);
-	ide_dma_start(drive);
-}
-
-static void sl82c105_dma_clear(ide_drive_t *drive)
-{
-	struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
-
-	sl82c105_reset_host(dev);
-}
-
-static int sl82c105_dma_end(ide_drive_t *drive)
-{
-	struct pci_dev *dev	= to_pci_dev(drive->hwif->dev);
-	int reg 		= 0x44 + drive->dn * 4;
-	int ret			= ide_dma_end(drive);
-
-	pci_write_config_word(dev, reg,
-			      (unsigned long)ide_get_drivedata(drive));
-
-	return ret;
-}
-
-/*
- * ATA reset will clear the 16 bits mode in the control
- * register, we need to reprogram it
- */
-static void sl82c105_resetproc(ide_drive_t *drive)
-{
-	struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
-	u32 val;
-
-	pci_read_config_dword(dev, 0x40, &val);
-	val |= (CTRL_P1F16 | CTRL_P0F16);
-	pci_write_config_dword(dev, 0x40, val);
-}
-
-/*
- * Return the revision of the Winbond bridge
- * which this function is part of.
- */
-static u8 sl82c105_bridge_revision(struct pci_dev *dev)
-{
-	struct pci_dev *bridge;
-
-	/*
-	 * The bridge should be part of the same device, but function 0.
-	 */
-	bridge = pci_get_domain_bus_and_slot(pci_domain_nr(dev->bus),
-					dev->bus->number,
-					PCI_DEVFN(PCI_SLOT(dev->devfn), 0));
-	if (!bridge)
-		return -1;
-
-	/*
-	 * Make sure it is a Winbond 553 and is an ISA bridge.
-	 */
-	if (bridge->vendor != PCI_VENDOR_ID_WINBOND ||
-	    bridge->device != PCI_DEVICE_ID_WINBOND_83C553 ||
-	    bridge->class >> 8 != PCI_CLASS_BRIDGE_ISA) {
-	    	pci_dev_put(bridge);
-		return -1;
-	}
-	/*
-	 * We need to find function 0's revision, not function 1
-	 */
-	pci_dev_put(bridge);
-
-	return bridge->revision;
-}
-
-/*
- * Enable the PCI device
- * 
- * --BenH: It's arch fixup code that should enable channels that
- * have not been enabled by firmware. I decided we can still enable
- * channel 0 here at least, but channel 1 has to be enabled by
- * firmware or arch code. We still set both to 16 bits mode.
- */
-static int init_chipset_sl82c105(struct pci_dev *dev)
-{
-	u32 val;
-
-	pci_read_config_dword(dev, 0x40, &val);
-	val |= CTRL_P0EN | CTRL_P0F16 | CTRL_P1F16;
-	pci_write_config_dword(dev, 0x40, val);
-
-	return 0;
-}
-
-static const struct ide_port_ops sl82c105_port_ops = {
-	.set_pio_mode		= sl82c105_set_pio_mode,
-	.set_dma_mode		= sl82c105_set_dma_mode,
-	.resetproc		= sl82c105_resetproc,
-	.test_irq		= sl82c105_test_irq,
-};
-
-static const struct ide_dma_ops sl82c105_dma_ops = {
-	.dma_host_set		= ide_dma_host_set,
-	.dma_setup		= ide_dma_setup,
-	.dma_start		= sl82c105_dma_start,
-	.dma_end		= sl82c105_dma_end,
-	.dma_test_irq		= ide_dma_test_irq,
-	.dma_lost_irq		= sl82c105_dma_lost_irq,
-	.dma_timer_expiry	= ide_dma_sff_timer_expiry,
-	.dma_clear		= sl82c105_dma_clear,
-	.dma_sff_read_status	= ide_dma_sff_read_status,
-};
-
-static const struct ide_port_info sl82c105_chipset = {
-	.name		= DRV_NAME,
-	.init_chipset	= init_chipset_sl82c105,
-	.enablebits	= {{0x40,0x01,0x01}, {0x40,0x10,0x10}},
-	.port_ops	= &sl82c105_port_ops,
-	.dma_ops	= &sl82c105_dma_ops,
-	.host_flags	= IDE_HFLAG_IO_32BIT |
-			  IDE_HFLAG_UNMASK_IRQS |
-			  IDE_HFLAG_SERIALIZE_DMA |
-			  IDE_HFLAG_NO_AUTODMA,
-	.pio_mask	= ATA_PIO5,
-	.mwdma_mask	= ATA_MWDMA2,
-};
-
-static int sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id)
-{
-	struct ide_port_info d = sl82c105_chipset;
-	u8 rev = sl82c105_bridge_revision(dev);
-
-	if (rev <= 5) {
-		/*
-		 * Never ever EVER under any circumstances enable
-		 * DMA when the bridge is this old.
-		 */
-		printk(KERN_INFO DRV_NAME ": Winbond W83C553 bridge "
-				 "revision %d, BM-DMA disabled\n", rev);
-		d.dma_ops = NULL;
-		d.mwdma_mask = 0;
-		d.host_flags &= ~IDE_HFLAG_SERIALIZE_DMA;
-	}
-
-	return ide_pci_init_one(dev, &d, NULL);
-}
-
-static const struct pci_device_id sl82c105_pci_tbl[] = {
-	{ PCI_VDEVICE(WINBOND, PCI_DEVICE_ID_WINBOND_82C105), 0 },
-	{ 0, },
-};
-MODULE_DEVICE_TABLE(pci, sl82c105_pci_tbl);
-
-static struct pci_driver sl82c105_pci_driver = {
-	.name		= "W82C105_IDE",
-	.id_table	= sl82c105_pci_tbl,
-	.probe		= sl82c105_init_one,
-	.remove		= ide_pci_remove,
-	.suspend	= ide_pci_suspend,
-	.resume		= ide_pci_resume,
-};
-
-static int __init sl82c105_ide_init(void)
-{
-	return ide_pci_register_driver(&sl82c105_pci_driver);
-}
-
-static void __exit sl82c105_ide_exit(void)
-{
-	pci_unregister_driver(&sl82c105_pci_driver);
-}
-
-module_init(sl82c105_ide_init);
-module_exit(sl82c105_ide_exit);
-
-MODULE_DESCRIPTION("PCI driver module for W82C105 IDE");
-MODULE_LICENSE("GPL");