de6*/dl2k/sundance: Move the D-Link drivers

Move the D-Link drivers into drivers/net/ethernet/dlink/ and
make the necessary Kconfig and Makefile changes.

CC: Bjorn Ekwall <bj0rn@blox.se>
CC: Donald Becker <becker@scyld.com>
CC: Edward Peng <edward_peng@dlink.com.tw>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

1 files changed, 0 insertions, 117 deletions

diff --git a/drivers/net/de620.h b/drivers/net/de620.h
deleted file mode 100644
index e8d9a88f4cb5..000000000000
--- a/drivers/net/de620.h
+++ /dev/null
@@ -1,117 +0,0 @@
-/*********************************************************
- *                                                       *
- * Definition of D-Link DE-620 Ethernet Pocket adapter   *
- *                                                       *
- *********************************************************/
-
-/* DE-620's CMD port Command */
-#define CS0		0x08	/* 1->0 command strobe */
-#define ICEN		0x04	/* 0=enable DL3520 host interface */
-#define DS0		0x02	/* 1->0 data strobe 0 */
-#define DS1		0x01	/* 1->0 data strobe 1 */
-
-#define WDIR		0x20	/* general 0=read  1=write */
-#define RDIR		0x00	/*  (not 100% confirm ) */
-#define PS2WDIR		0x00	/* ps/2 mode 1=read, 0=write */
-#define PS2RDIR		0x20
-
-#define IRQEN		0x10	/* 1 = enable printer IRQ line */
-#define SELECTIN	0x08	/* 1 = select printer */
-#define INITP		0x04	/* 0 = initial printer */
-#define AUTOFEED	0x02	/* 1 = printer auto form feed */
-#define STROBE		0x01	/* 0->1 data strobe */
-
-#define RESET		0x08
-#define NIS0		0x20	/* 0 = BNC, 1 = UTP */
-#define NCTL0		0x10
-
-/* DE-620 DIC Command */
-#define W_DUMMY		0x00	/* DIC reserved command */
-#define W_CR		0x20	/* DIC write command register */
-#define W_NPR		0x40	/* DIC write Next Page Register */
-#define W_TBR		0x60	/* DIC write Tx Byte Count 1 reg */
-#define W_RSA		0x80	/* DIC write Remote Start Addr 1 */
-
-/* DE-620's STAT port bits 7-4 */
-#define EMPTY		0x80	/* 1 = receive buffer empty */
-#define INTLEVEL	0x40	/* 1 = interrupt level is high */
-#define TXBF1		0x20	/* 1 = transmit buffer 1 is in use */
-#define TXBF0		0x10	/* 1 = transmit buffer 0 is in use */
-#define READY		0x08	/* 1 = h/w ready to accept cmd/data */
-
-/* IDC 1 Command */
-#define	W_RSA1		0xa0	/* write remote start address 1 */
-#define	W_RSA0		0xa1	/* write remote start address 0 */
-#define	W_NPRF		0xa2	/* write next page register NPR15-NPR8 */
-#define	W_DFR		0xa3	/* write delay factor register */
-#define	W_CPR		0xa4	/* write current page register */
-#define	W_SPR		0xa5	/* write start page register */
-#define	W_EPR		0xa6	/* write end page register */
-#define	W_SCR		0xa7	/* write system configuration register */
-#define	W_TCR		0xa8	/* write Transceiver Configuration reg */
-#define	W_EIP		0xa9	/* write EEPM Interface port */
-#define	W_PAR0		0xaa	/* write physical address register 0 */
-#define	W_PAR1		0xab	/* write physical address register 1 */
-#define	W_PAR2		0xac	/* write physical address register 2 */
-#define	W_PAR3		0xad	/* write physical address register 3 */
-#define	W_PAR4		0xae	/* write physical address register 4 */
-#define	W_PAR5		0xaf	/* write physical address register 5 */
-
-/* IDC 2 Command */
-#define	R_STS		0xc0	/* read status register */
-#define	R_CPR		0xc1	/* read current page register */
-#define	R_BPR		0xc2	/* read boundary page register */
-#define	R_TDR		0xc3	/* read time domain reflectometry reg */
-
-/* STATUS Register */
-#define EEDI		0x80	/* EEPM DO pin */
-#define TXSUC		0x40	/* tx success */
-#define T16		0x20	/* tx fail 16 times */
-#define TS1		0x40	/* 0=Tx success, 1=T16 */
-#define TS0		0x20	/* 0=Tx success, 1=T16 */
-#define RXGOOD		0x10	/* rx a good packet */
-#define RXCRC		0x08	/* rx a CRC error packet */
-#define RXSHORT		0x04	/* rx a short packet */
-#define COLS		0x02	/* coaxial collision status */
-#define LNKS		0x01	/* UTP link status */
-
-/* Command Register */
-#define CLEAR		0x10	/* reset part of hardware */
-#define NOPER		0x08	/* No Operation */
-#define RNOP		0x08
-#define RRA		0x06	/* After RR then auto-advance NPR & BPR(=NPR-1) */
-#define RRN		0x04	/* Normal Remote Read mode */
-#define RW1		0x02	/* Remote Write tx buffer 1  ( page 6 - 11 ) */
-#define RW0		0x00	/* Remote Write tx buffer 0  ( page 0 - 5 ) */
-#define TXEN		0x01	/* 0->1 tx enable */
-
-/* System Configuration Register */
-#define TESTON		0x80	/* test host data transfer reliability */
-#define SLEEP		0x40	/* sleep mode */
-#if 0
-#define FASTMODE	0x04	/* fast mode for intel 82360SL fast mode */
-#define BYTEMODE	0x02	/* byte mode */
-#else
-#define FASTMODE	0x20	/* fast mode for intel 82360SL fast mode */
-#define BYTEMODE	0x10	/* byte mode */
-#endif
-#define NIBBLEMODE	0x00	/* nibble mode */
-#define IRQINV		0x08	/* turn off IRQ line inverter */
-#define IRQNML		0x00	/* turn on IRQ line inverter */
-#define INTON		0x04
-#define AUTOFFSET	0x02	/* auto shift address to TPR+12 */
-#define AUTOTX		0x01	/* auto tx when leave RW mode */
-
-/* Transceiver Configuration Register */
-#define JABBER		0x80	/* generate jabber condition */
-#define TXSUCINT	0x40	/* enable tx success interrupt */
-#define T16INT		0x20	/* enable T16 interrupt */
-#define RXERRPKT	0x10	/* accept CRC error or short packet */
-#define EXTERNALB2	0x0C	/* external loopback 2 */
-#define EXTERNALB1	0x08	/* external loopback 1 */
-#define INTERNALB	0x04	/* internal loopback */
-#define NMLOPERATE	0x00	/* normal operation */
-#define RXPBM		0x03	/* rx physical, broadcast, multicast */
-#define RXPB		0x02	/* rx physical, broadcast */
-#define RXALL		0x01	/* rx all packet */
-#define RXOFF		0x00	/* rx disable */