e1000e: use generic IEEE MII definitions

For standard IEEE MII-compatible transceivers, the kernel has generic
register and bit definitions.  Use those instead of redundant local
defines.

Do not replace references of MII_CR_SPEED_10 with BMCR_SPEED10 (0x0000)
when it is not necessary (i.e. when it is bitwise OR'ed with another
value).

Some whitespace issues in the surrounding context of the above changes are
also cleaned up.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

1 files changed, 0 insertions, 60 deletions

diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index 1257f917af34..615b900c0152 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -563,66 +563,6 @@
 			   E1000_GCR_TXDSCW_NO_SNOOP      | \
 			   E1000_GCR_TXDSCR_NO_SNOOP)
 
-/* PHY Control Register */
-#define MII_CR_FULL_DUPLEX      0x0100  /* FDX =1, half duplex =0 */
-#define MII_CR_RESTART_AUTO_NEG 0x0200  /* Restart auto negotiation */
-#define MII_CR_POWER_DOWN       0x0800  /* Power down */
-#define MII_CR_AUTO_NEG_EN      0x1000  /* Auto Neg Enable */
-#define MII_CR_LOOPBACK         0x4000  /* 0 = normal, 1 = loopback */
-#define MII_CR_RESET            0x8000  /* 0 = normal, 1 = PHY reset */
-#define MII_CR_SPEED_1000       0x0040
-#define MII_CR_SPEED_100        0x2000
-#define MII_CR_SPEED_10         0x0000
-
-/* PHY Status Register */
-#define MII_SR_LINK_STATUS       0x0004 /* Link Status 1 = link */
-#define MII_SR_AUTONEG_COMPLETE  0x0020 /* Auto Neg Complete */
-
-/* Autoneg Advertisement Register */
-#define NWAY_AR_10T_HD_CAPS      0x0020   /* 10T   Half Duplex Capable */
-#define NWAY_AR_10T_FD_CAPS      0x0040   /* 10T   Full Duplex Capable */
-#define NWAY_AR_100TX_HD_CAPS    0x0080   /* 100TX Half Duplex Capable */
-#define NWAY_AR_100TX_FD_CAPS    0x0100   /* 100TX Full Duplex Capable */
-#define NWAY_AR_PAUSE            0x0400   /* Pause operation desired */
-#define NWAY_AR_ASM_DIR          0x0800   /* Asymmetric Pause Direction bit */
-
-/* Link Partner Ability Register (Base Page) */
-#define NWAY_LPAR_100TX_FD_CAPS  0x0100 /* LP 100TX Full Dplx Capable */
-#define NWAY_LPAR_PAUSE          0x0400 /* LP Pause operation desired */
-#define NWAY_LPAR_ASM_DIR        0x0800 /* LP Asymmetric Pause Direction bit */
-
-/* Autoneg Expansion Register */
-#define NWAY_ER_LP_NWAY_CAPS     0x0001 /* LP has Auto Neg Capability */
-
-/* 1000BASE-T Control Register */
-#define CR_1000T_HD_CAPS         0x0100 /* Advertise 1000T HD capability */
-#define CR_1000T_FD_CAPS         0x0200 /* Advertise 1000T FD capability  */
-					/* 0=DTE device */
-#define CR_1000T_MS_VALUE        0x0800 /* 1=Configure PHY as Master */
-					/* 0=Configure PHY as Slave */
-#define CR_1000T_MS_ENABLE       0x1000 /* 1=Master/Slave manual config value */
-					/* 0=Automatic Master/Slave config */
-
-/* 1000BASE-T Status Register */
-#define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */
-#define SR_1000T_LOCAL_RX_STATUS  0x2000 /* Local receiver OK */
-
-
-/* PHY 1000 MII Register/Bit Definitions */
-/* PHY Registers defined by IEEE */
-#define PHY_CONTROL      0x00 /* Control Register */
-#define PHY_STATUS       0x01 /* Status Register */
-#define PHY_ID1          0x02 /* Phy Id Reg (word 1) */
-#define PHY_ID2          0x03 /* Phy Id Reg (word 2) */
-#define PHY_AUTONEG_ADV  0x04 /* Autoneg Advertisement */
-#define PHY_LP_ABILITY   0x05 /* Link Partner Ability (Base Page) */
-#define PHY_AUTONEG_EXP  0x06 /* Autoneg Expansion Reg */
-#define PHY_1000T_CTRL   0x09 /* 1000Base-T Control Reg */
-#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */
-#define PHY_EXT_STATUS   0x0F /* Extended Status Reg */
-
-#define PHY_CONTROL_LB   0x4000 /* PHY Loopback bit */
-
 /* NVM Control */
 #define E1000_EECD_SK        0x00000001 /* NVM Clock */
 #define E1000_EECD_CS        0x00000002 /* NVM Chip Select */